Window paint. How and with what to paint old wooden frames? The better to cover wooden windows

Painting wooden windows can not only give them an original appearance, but also protect the material from impacts environment negative nature.

In order for the paint to properly lay down on the surface of the frame, you must follow the rules for painting. Also, the quality of this procedure directly depends on the quality of the paint that will be applied to the surface of the frames.

The right choice of paint will not only ennoble the appearance of the window, but also significantly extend its life. When choosing a paint, it is necessary to give preference to those materials that are characterized by resistance to moisture.

Otherwise, moisture can penetrate the window frame and cause damage to the window structure.

Wood is subject to swelling and shrinkage, which requires the choice of a flexible paint. Inelastic material can crack.

Most the best option for painting wooden windows is alkyd paint with the addition of oil. This material is characterized high level strength and elasticity, which protects it from deformation.

When choosing a paint for painting a window sill, it is necessary to give preference to materials that are resistant to mechanical damage. The choice of paint color also needs to be approached as seriously as possible.

For painting the outside of the window, it is better to give preference light colors, which will beat off the sun's rays, which will protect the window frame from premature drying out. The inside of the window can be painted in any color, but the consistency of the paint must be uniform.

Painting of wooden windows is carried out in several stages. The main ones include:

• Preparation of the premises;
• Seizure of accessories;
• Cleaning the surface of old paint;
• Puttying;
• Painting.

At the first stage, it is necessary to clean not only the window, but the entire room from dust that can settle on the paint and spoil the appearance of the window.

In order for the window painting to be done as accurately as possible, it is necessary to remove the fittings from the window frame. This will not only speed up the painting process, but also protect the fittings from accidental staining.

An important step in painting windows is the process of removing old paint. The quality of painting depends on the effectiveness of this action. Using a spatula, it is necessary to remove layers of old paint in hard-to-reach places Oh.

The frame itself must be wiped with white spirit, and then washed with water. The next step is puttying, which must be done only if there is damage to the window frame. To perform this action, you must use a special putty for wood.

Before you start painting, the window frame must be primed. Painting is carried out in dry and warm weather. To perform this action, you can use a regular shield.

The choice of material for painting windows is quite wide. Very often, people choose varnish to perform this action. This is explained by given material is able not only to give an unsurpassed appearance to the window, but also has excellent technical characteristics.

Lacquer for wooden window frames should be characterized by a high thistotropy, which will allow it to be applied in a thick layer without streaks.

To create a special rustic effect, it is best to choose a high-transparent varnish. With it, you can emphasize the original structure of wood. Works on painting windows with varnish are carried out in the same order as when covering the surface with paint.

Painting windows is a fairly simple procedure. When all the rules of painting and when right choice lacquer coating can provide a very attractive appearance of the window.

You will also find a video about painting wooden windows useful.

Hide

For many generations, the question has been tormented by what paint to paint wooden windows! Someone says that there is no difference - it will peel off anyway. And someone comes up with tricky recipes in which there are two, three or more ingredients.

We Let's list the most "reliable" means. We will also give instructions on how to properly paint wooden windows..

How to paint wooden windows: paint varnish strife

A set of paints and varnishes for painting wooden windows includes:

1. Water-dispersion acrylic(dilute with water) or alkyd enamel paint- based on resins. Advertising says that both have good water resistance. However, the people trust the second one more.

Someone advise oil paints, but they dry for a very long time for external work.

Increasingly, wooden windows are painted with transparent varnishes - to preserve the texture of wood.

2. Can be used instead of paint clear varnishes. They are the same alkyd enamel, only without the coloring pigment.

3. Primer on wood, or just drying oil- to keep the paint well. It is very easy to determine which primer is right for you. For water-dispersion paints fits on acrylic base, i.e. the composition of paint and primer is similar. With enamel, alkyd drying oil is used.

4. Mordant based on white alcohol- with wood protection properties. Those. so that the wood does not absorb moisture and bugs do not eat it.

You can choose putty color one to one with wood

5. Putty on wood.

Some use old-fashioned means: they mix wax with turpentine, rosin, etc. But if you absolutely “do not boil” in paints, it is more convenient to buy ready-made compositions. Fortunately, stores are bursting with them.

There are a variety of primers, thinners, base paints, top coats and varnishes, etc. You can easily find the best way to paint wooden windows only outside, only inside, and universal rulers - suitable for outdoor and internal works.

The most popular "paint and varnish" brand is Tikkurila. Consumers praise her on the forums the most. True, the price, they write, is too immodest. Brands are also mentioned: Pinotex, Zawosan, Tex, etc.

We paint - we do not repaint

You can paint a wooden window, old or new, yourself:

1. If the window has already been painted, it needs to be sanded first. You will find several simple ways to do this in the article:.

For smoothness, the window is sanded first large, and then small. sandpaper

2. Next, prepare your profile. If there are cracks on it, cover them with wood putty. Sand the rough surface of the wood with sandpaper (first large - No. 150, and then smaller - No. 180 or 220). If this is not done, after staining the villi on the profile will “stand on end”.

3. Remove dust and cleaning from the wood with a damp cloth.

4. Stir the stain and apply it with a brush or swab so that there are no smudges. Therefore, moisten the swab or brush in the stain is not very generous.

The stain usually dries in 6-8 hours.

5. After this time, also apply a primer or drying oil to the window with a brush. There are several options here. Sometimes it is applied to the stain, if, for example, the latter is not on water based. Often the stain is not used at all, but immediately primed. In this case, the result can also be quite good.

Choose any paint color. But on the outer sunny side, make the profile white so that the rays are reflected from it and the paint does not deteriorate

6. Once the primer dries, start painting or varnishing. If the paint is too thick, dilute with a thinner (buying it is not a problem). Mix not all at once, but little by little. The consistency of the paint should be more like cream than sour cream.

"Enlightened" recommend starting painting from the outside of the window. They say that the moisture accumulated by the tree could evaporate into the apartment. Well, there is logic in this. But it is much more logical to paint the window in the summer in dry weather, when it has not yet had time to get wet.

Apply the paint along the fibers with a well wrung out brush. thin layer. After the first has dried, proceed to the second. And then to the third layer, if the first two were not enough.

Painting a wooden window and not smearing glass with walls is almost an art. How to master it, look at video:

Prices for painting wooden windows in Moscow

Yes, yes, and there is such a service on the domestic market, which is offered by window makers and firms for general repair. So how much does it cost to paint wooden windows? The price of the work alone is from 300 rubles. per m2 of surface. If you count the materials, then the amount will come out 10 times more. True, you also need to take into account the condition of the window, painting or repainting is required, etc.

Most people keep up with the times - choose new Decoration Materials, install modern doors and windows. But there are people who do not want to part with wooden windows. And there are enough hosts. Every year you have to pay attention to old windows in order to keep them in proper order: twist, change glazing beads and paint wooden frames. So that the process does not drag out, and the windows cope with the tasks, it is necessary to prepare all the materials and tools in advance.

Self-repair of wooden windows is not an easy task. This process is time-consuming, since every year of operation wooden frames are exposed to atmospheric precipitation and constant temperature fluctuations. The tree wears out especially after the autumn-winter period, when cold air blows through the windows from the street, and from the side of the room the temperature is several tens of degrees higher. As a result of such drops, condensation forms on the windows, wooden frames either freeze or swell. The tree can rot, mold appears. To prevent this from happening, it is necessary to properly care for the windows, namely, to adhere to the technology of painting wooden windows.

Preparation of tools and materials

In order to paint wooden window frames, you must first bring the frames into proper condition. We start with an inspection, then we prepare necessary tools and materials.

What we may need:

• electric grinder or drill plus attachments;
• foam roller for coloring;
• spatula for removing old paint;
• scraper and several brushes;
• fine-grained grinder;
• construction tape;
• film or old newspapers;
• rags;
• paint container.

From the materials you need to prepare the following:

• putty;
• paint;
• solvent;
• primer.

It is also necessary to think over the support in advance - it can be a strong chair or stool, and best of all - a stepladder. In addition, immediately prepare a hammer, some nails, a chisel and a screwdriver. And that's not all: you need to take care of protective equipment: buy glasses, gloves, a mask or respirator, a hat on your head (or tie a scarf).

Now about the choice of materials: for painting wooden surfaces, choose special paint oil-based - alkyd. This is for indoor work. Outside, it is best to paint wooden windows with acrylic paint. By the way, you can buy one paint - universal, for indoor and outdoor work. The price of painting wooden windows can vary significantly and depend on the cost of materials.

Where to begin. Surface preparation

Every owner knows that surface preparation is no less important than the painting process itself. If you pay maximum attention to this issue, then wooden frames can be saved for long years. None weather should not affect the condition of the tree: rain, blizzard, heat or dust. Therefore, the first rule is to choose the best day for painting. It's good to work when it's not hot outside, not it's raining and there is no wind. The frames will dry well when the air temperature does not drop below +5 ° C, the humidity should be quite high - up to 80%. If the day is cloudy, it is damp outside, then the tree will not dry well. The paint will seize, but it can "take" bubbles, and this is bad for the tree. In a few months, you will have to redo all the work again. By the way, the paint can peel off not only because of wet weather, but also due to non-compliance with the painting technology. If the surface is poorly cleaned of dirt and old paint or when a primer is not used.

How to clean frames from old paint? Many people ask this question. For work, it is necessary to prepare sandpaper (coarse-grained) and a scraper. Before starting work, check if the wooden frame closes well. If it’s bad - the tree is damaged and the paint is swollen, then you need to trim the frame using a drill with a nozzle or a grinder (grinder). When doing this part of the work, be extremely careful and careful not to damage the tree. If this option is too difficult for you, go to the hardware store, they are now on sale special means for removing paint. You just need to apply the liquid to the surface and wait a bit. Then the removal process will not take much time. Pay attention to the Tikkurila or Svema paint removers. If there is nothing suitable in the construction stores, go to the car shop, there big choice similar means suitable for removing paint from wooden surfaces.

We apply the product on wooden frames (we work with gloves and a respirator). We are waiting for the paint to rise, wrinkle. Then we take a spatula in our hands and remove layers of paint. We clean the remains with sandpaper with a large grain.

Before you start painting wooden windows, you need to remove all unnecessary, metal parts also need to be unscrewed (latches, handles, locks). If you can’t unscrew something that interferes, you can paste over these places with construction tape so as not to accidentally paint over these places. Of course, the ideal option is to remove the old fittings and, after painting the wooden frame, screw on the new one.

Now a few words about the preparation of glasses. If you have never painted wooden frames before, then you should not rely on your accuracy, but it is better to immediately seal the glass with at least adhesive tape next to the frame so that the paint does not get on the glass.

Tip from experienced craftsmen: before you start painting wooden windows, stick masking tape on the glass, just step back 2 mm from the frame. The paint will fill the void and gaps between the glass and the frame. Moisture will not accumulate in these places.

Do you know why the glasses "tremble" when strong wind? They don't fit well in frames. This means it's time to change the rails. New strips are painted separately and nailed last, after painting the frames.

Priming and puttying. Is it really that important?

The preliminary inspection is completed, you can proceed to the next stage - the primary processing of the tree. Once again, we pay attention to the wooden frame: if there are metal fasteners that cannot be removed, it is necessary to treat the parts with a special primer for metal ( Special attention let's pay attention to the "hats" of nails, hinged loops, etc.).

To prevent the destruction of the wooden frame, it is necessary to treat the surface with a special antiseptic solution. This will get rid of the reproduction of insects and prevent decay. We have completed these points, then you need to take a good look at wooden surface. Did you see depressions, bumps or potholes? All these places must be filled with putty. Just try to apply each layer a little and do not rush. Otherwise, a dense layer of putty will not have time to dry properly. If you rush and immediately start painting the windows, then the putty will fall off the tree along with the paint. You will have to tinker to correct mistakes.

What should be the putty? Only special, designed for wooden surfaces. Such putty is sold in any hardware store in small jars. Alkyd wood putty "Lakkakitti" has proven itself well.

Several simple tips for painting wooden windows:

• did you buy paint? Then just put putty on the wood;
• if you use varnish, then before covering the damaged areas, you need to apply stain in several layers so that the treated areas do not stand out;
• color for wood can be prepared independently from very fine sawdust, resin and glue.

How to apply putty correctly:

1. Clean the surface of old paint.
2. Go over the frames with sandpaper to smooth out the bumps.
3. Remove debris and dust with a damp cloth.
4. Apply a thin layer of putty with a spatula, smooth out the bumps.
5. We wait 1-2 hours for the layer to dry. We clean it with fine-grained sandpaper.
6. We brush off the particles of dry putty with a rag.
7. We examine our work: if necessary, repeat all the steps again to achieve a perfectly flat surface.

Now second preparatory stage- Applying a primer. It is designed to ensure a reliable adhesion of the paint to the wood. Choose a proven primer with the added function of surface decontamination. Good feedback at the primer-antiseptic company "Pinotex". After application, the primer forms an invisible layer on the surface. protective film, which allows not only to provide protection against insects and decay, but also maintains an optimal moisture balance. Another primer on wood retains the structure natural material. Therefore, it is so important to choose the material for its intended purpose. Metal primer is not suitable for wooden frames.

Before applying the primer, it is necessary to degrease the wood. For these purposes, white spirit is suitable. Apply liquid with a roller, work with gloves and a protective mask. How to understand if the putty has dried or not? Once you apply the degreaser, wet areas darken. This means that the putty has not dried out yet. It may also happen that you did everything right and started painting wooden frames. After drying, the paint found that the surface was not painted evenly - dark areas appeared. This means that the putty has not completely dried out, or you missed a section of wood and did not apply a primer coat.

In a good way, it is better to redo such work immediately. To do this, you need to clean these areas with sandpaper to the ground, apply a layer of primer, and then a layer of paint.

How to paint wooden windows

Wooden frames are ready for painting. Now most beginners have questions: "How to paint wooden windows neatly"? There is nothing difficult here, you just need to follow simple rules. The main thing is to clean the room so that there is no debris and dust around. It is also necessary to wipe the window sill so that nothing interferes with you when painting.

For painting, it is better to use water-based paint, alkyd enamel or acrylic paints. The main advantage of this material: strength, stability, ease of application.

How to paint wooden windows:

1. Open the paint can. Make a handy stick for mixing paint from an old plank. Stir the contents of the can very carefully, as the paint may have peeled off during storage.
2. Ideally, if you strain the paint through a metal sieve into another container to get rid of lumps. But if that's not possible, skip this step. Not every owner has an old metal sieve that is not a pity to use in work.
3. Pour a small portion of paint into a convenient jar (you can apply tin can from canned food).
4. Dip the brush into the paint, squeezing the excess from the brush so as not to spill the paint around.
5. Apply the first coat of paint to the wooden frames. At first, it will seem to you that it does not lie flat and there are light areas. This is normal, as the first layer impregnates the surface and fills in any irregularities.
6. The second layer will fit better.
7. If you see that the paint is thick, then you need to add a little thinner.
8. After applying the first layer, you need to wait until the paint is completely dry, and then proceed to re-staining.
9. Two coats of paint is not always enough. Everything is individual here and depends on the condition of the wooden frame and the quality of the paint itself. It also happens that it is also necessary to apply the 3rd, final layer, but only after the previous ones have completely dried.
10. Remember that when painting wooden frames for the 2nd and 3rd time, do not make the paint rare, it should be a little thicker than when it was first applied. This way you will avoid paint streaks. And if they appear, try to immediately remove the excess with a cloth dipped in a solvent.
11. If you missed this moment and did not immediately get rid of paint streaks, then be prepared for the fact that you will have to clean off the excess (with a knife or large sandpaper), and then paint this area again.
12. Do not forget to pre-glue construction tape on glass or thin paper. You can remove the protection even before the moment when the paint dries completely.
13. Try to apply paint along the wood fibers, so the material will lay down better. Make short and "light" strokes. Also try to paint over the corners easily, do not pour a lot of paint.
14. We try not to completely immerse the brush in a can of paint during work. Leftovers should be left at the edge of the container.
15. We start painting the surface from the street.
16. Prepare several brushes for work: narrow ones to get to hard-to-reach places, wide ones - to paint over a large and even area. Tassels should be flat, 2 to 5 cm wide.
17. After painting and complete drying of the paint, it is necessary to install the fittings in place.

Watch the video to reinforce the theory in practice:

Windows are the "eyes" of a home. Now most buildings seem to be impersonal due to the fact that typical PVC double-glazed windows are used everywhere. However, there are those who, despite fashion and practicality modern technologies still prefers wooden structure, because its environmental and aesthetic advantages are undeniable.

In order for wooden frames to last longer, it is necessary to reliably protect them from the effects of sunlight and dampness, as well as various insects and their larvae. To complete all these tasks, painting a wooden window is called upon. In addition, such processing will save long time appearance, however, provided that it was carried out correctly and in a timely manner. We will tell you how to paint and protect new wooden windows, as well as restore old ones if possible.

What tools will be required?

The simplest set is required when painting a new window. For old design the list is expanding significantly. From the tools, prepare in advance a spatula, a scraper, a drill with a special nozzle or a grinder, a roller and brushes, sandpaper (fine and coarse), a metal sieve, a paint container, a stable chair, a stool or a ladder-ladder, well, rags, and newspapers.

Next on the list - expendable materials. As a matter of fact, this is how to paint wooden windows and process them before that: putty, primer, paint, thinner, white spirit. Do not neglect protective equipment, such as a mask, goggles, a respirator, a hat and gloves.

What paint to choose for windows?

Even a professional cannot unequivocally answer the question of which paint to choose for painting windows. The preferences of each owner of a wooden structure are different. Someone for tradition and White color, others - for the naturalness and natural structure of wood. The modern construction market offers a very rich choice:

• alkyd enamel;
• acrylic (water-dispersed) paint;
• clear nail polish;
• Oil paint;
• primers and drying oil;
• solvent-based stain.

If preference is given to the natural color of wood, then experts recommend using special varnishes, azures and impregnations for coloring and protection. They perfectly penetrate the tree, form a water-repellent layer and prevent the penetration of rot and mold, and also protect against pests.

For interior work, it is preferable to use acrylic paint, which is practically odorless and dries quickly (literally in a couple of hours). Outside, the design is best handled. But the question of what kind of paint is better to paint wooden windows, imported or domestic, is a purely personal matter of each owner, his preferences and financial capabilities.

Step 1: Removing Old Paint from the Window Frame

If they are new from wood, then painting them is not particularly difficult. The situation is much more serious with old windows, which have already been repeatedly applied paint. Before carrying out a new processing, they should be carefully prepared. Peeling paint is best removed completely. And the better it is done, the more attractive the end result will be.

Old paint from windows can be removed using special compounds that soften the layers, gradually turning them into a curdled mass, easily removed with a scraper or spatula. However, it should be remembered that such products are quite toxic, and therefore gloves, goggles and a respirator should be used when working with it.

Can be used when processing old windows building hair dryer which will soften the old paint with hot air. Then it will be easy to remove it with a scraper. Remove the old coating in stages, warm up only small areas. Before the procedure, it is desirable to remove the glass from the frames.

If the coating is not very worn out under the influence of atmospheric factors, you can do with small preparatory activities and don't delete it completely. However, before painting wooden windows according to old paint, in any case, they should be carefully sanded and then cleaned of dust, and the irregularities should be treated with putty.

Step 2: sealing cracks and cracks

Wooden products have one significant drawback - this is cracking when dried. On the window frames quite often you can find both small and fairly deep cracks. Therefore, before painting, be sure to inspect the structure, including the joints of the window block with the wall. Cracks are where dirt and moisture accumulate. Thoroughly clean them from accumulated dust with a brush or vacuum cleaner, dry and fill with a special putty. After the composition has dried, sand the entire wooden surface with coarse sandpaper. Otherwise, after painting, uneven areas on the frame will be very noticeable.

Step 3: Coating the window frame with a primer

Before painting the wooden frame of the window, it is necessary to prime it. This is done not only in the case of new design, but also when stripping the old to the very tree. If this is not done, the paint will not hold well and in less than a year, it will have to be put in order again. The application of a primer promotes better adhesion of the paint to the surface, reduces its consumption. After using it, the wood fibers may rise slightly, so experts advise sanding the window frame again with fine-grained sandpaper. This should always be done in the direction of fiber growth.

The choice of primer depends directly on what kind of paint will be used in the future.

Step 4: the final stage of preparation before painting

The process of preparing wooden windows for painting ends with an inspection of the structure. Carefully inspect it for traces of resin. This is especially true if the frame is new and/or made from conifers tree. Resinous secretions should be carefully removed, as the acid present in their composition will gradually destroy the paint layer. Next, the surface of the wood must be degreased. Which composition should be used for these purposes depends on It must be compatible with it. So, since ancient times, complete with oil paint turpentine was used. Its residues on the surface did not in any way affect the quality of the painting. White spirit or simple kerosene, gasoline is popular.

Step 5: protect the glass surface of the window

As practice shows, even the most experienced craftsmen easily touch structures with a brush. Therefore, it will be better if you protect it with a special masking tape. The process will not take much time, but the painting of a wooden window will be much faster, and the coating will turn out without smudges, smooth and neat.

Keep in mind that you should remove from the glass surface before the paint on the window frame dries. Otherwise, there is a risk of tearing off part of the paintwork along with it.

Step 6: paint and brushes

Whatever composition you choose for painting a wooden window, you should first mix it well right in the jar. Then the paint must be filtered through a metal sieve into a special bath or other container. This step will save you from lumps that may later get on the surface to be painted.

Don't dip the brush all the way into the paint, it's best to do it half way. The excess should remain in the bath or jar. To do this, brush gently along the edge of the container. A large number of paint is completely useless, so you only contribute to the formation of smudges.

Prepare several types of brushes in advance. For the most inaccessible places, those that are smaller are suitable, for a flat surface - large ones or a roller. A flat brush is much more preferable than a round one.

Step 7: Apply paint to the surface

So, having learned how to prepare the surface before painting wooden windows from the outside and inside and having completed this stage, you can safely proceed to the main work.

It is best to paint a window from the inside out. Should open the frame and initially process internal surfaces primarily horizontal. Then move from bottom to top. If there are curly elements on the frame, it is better to start with them, using a narrow brush. For even surfaces, use a roller, because with its help the paint lays down much more evenly. Apply it in several layers (2-3). Do not try to close all dents, gaps and cracks with one stroke. A thick layer of paint will certainly begin to spread, sagging will appear and, in general, the work may be spoiled.

Apply a thin first layer and let it dry. The waiting time depends on the weather and humidity. When the surface is ready, apply a second coat of paint. As a rule, this is enough. In the case of old windows, a third coat may be necessary, as dry wood absorbs paint heavily.

When is the best time to paint windows?

The question of what weather is best for painting windows is far from being idle, as it might seem at first glance. Experts always pay attention to this aspect. They advise to carry out work on a cloudy spring day, when it is already warm, but there is still little moisture in the air, and ultraviolet does not have a damaging effect on the paint. Window frames dry best at temperatures above +5°C and humidity no more than 80%. Avoid rainy weather. Drops of water on the surface to which the paint is applied lead to further "bubble" of the coating. It not only spoils aesthetic appearance, but also contributes to the rapid destruction. In addition, when painting a wooden window, the coating may peel off due to dampness, poor primer, or poor pre-cleaning of the surface.

Wooden window frames require periodic painting. In order not to repeat this process every year, you should take it responsibly, prepare all building materials and special tools in advance.

Repair of wooden frames is the most time-consuming process. From the street they are influenced sunlight and precipitation, and from the side of the rooms - an increased temperature compared to the street, dry air or water condensate. In addition, insects often start in wooden windows, and can develop. To avoid these troubles, strictly follow the order of processing the tree.

Repair of wooden frames begins with their detailed inspection and preparation. building materials and tools. To paint old wooden windows, you will need the following materials and tools: scraper, spatula, sandpaper, grinder machine, roller, brushes, adhesive tape, window film, primer, putty, white spirit, thinner and paint. Do not forget about the mandatory ways to protect yourself from harmful volatile substances: mask, goggles, gloves and panama.

For painting wooden windows from the inside of the room, oil-based alkyd paint is usually used, and from the side of the street - acrylic paint for outdoor use. The choice of domestic or imported paint will depend on the cost of your repair and preferences.

Preparing wooden windows for painting

In order for wooden frames to last longer, it is necessary to choose the right time for painting. ideal condition a warm day without a bright hot sun, when the humidity is low and ultraviolet does not destroy the paint structure, is considered for repair. Wooden frames dry well at temperatures above 5°C and relative humidity below 80%. Do not apply paint on a damp surface, because. later bubbles may appear on it, and the frame will have to be repainted. The peeling of the paint also occurs due to dampness or poor pre-cleaning.

Preparing windows for painting

Let's take a closer look at how to paint and wooden frames in frame house. The first thing to do is to remove the old layer of paint. For this work, use a scraper and sandpaper with a large grain. If there are problems closing the frame, use a surface grinder. Use the machine carefully so as not to damage the wooden base of the frame.

Remover for removing old paint

Currently on construction markets appeared special liquids for removing the old layer of paint, such as Tikkurila, Shostka, Svema and more. This significantly speeds up the process of preparing wooden frames for repair. This mixture is applied to the frames, and when the paint is wrinkled and turns into a curdled substance, it is scraped off with a spatula, and the surface is treated with coarse sandpaper.

It is better to remove the sashes of wooden windows and all fittings before painting so that after painting the window looks more neat. If it is not possible to remove the handles or locks, simply cover them with masking tape.

We also carefully and accurately prepare all the glass windows. It is necessary to seal all the glasses with newspapers, fastening them with adhesive tape on the sides, retreating from each edge by 2 mm, so that the paint gets into narrow cracks and does not allow moisture and water to accumulate in the future. Throw away the old glazing beads, and paint the new ones separately from the frames and nail the finished ones with carnations.

The process of filling and priming wooden windows

Take a close look at the wood frame. All details and elements that can rust over time and ruin your repair, pre-treat specifically for iron (stud caps, metal hinges, etc.).

An antiseptic is important detail preparatory work before painting frames. This processing will prevent wood decay, the development and formation of fungus, and will not allow insects to settle in yours. will make your frame last longer.

After treating the frame with an antiseptic, inspect the surface of the window. All cracks, undulations or potholes must be filled. But do it gradually, because thick layer putty may fall off along with a layer of paint, and you will have to start the repair again.

After applying the first layer of putty, you need to clean the surface with sandpaper. After a few hours, when the second layer dries well, once again we level the entire surface of the frame with sandpaper. The process must be repeated until the surface of the wooden frame is perfectly flat.

The next step is the primer. This process will ensure a reliable and high-quality coating of wood with paint. Modern primer mixtures are also. When applied, it forms a protective transparent film, which is necessary to preserve the natural pattern of wood. In addition, primer mixtures protect well from mold, dampness and fungi, do not allow decay processes to develop on outside frames, even with increased humidity.

window primer

The primer consists of the following elements: oil, resin, glue, and various pigments. The recipe of each primer mixture is significantly different, however, there is a common among all primers for wood - this is their ability to preserve the natural structure of wood. Therefore, a metal primer for wooden parts do not use.

Before priming the surface, it is necessary to thoroughly degrease it with white spirit. It is better to prime with a brush, not a roller. If the putty is not very well dried or you missed the area when priming the surface, after painting on this place a dark spot may form.

Painting a wooden window in several layers

After the above treatment, the window is smooth and even. Before painting, it is necessary to carefully clean the room, clean the space near the wooden window from dust so that it cannot get on the freshly painted frame.

When renovating, many people are faced with the question of what color to paint the windows? As a rule, water-acrylate or alkyd enamels are chosen for painting wooden frames. Their main advantages are high moisture resistance, elasticity and resistance to fading from sunlight. In our country, with sudden changes in temperature, changeable weather, precipitation, Dulux, Remmers, Caparol will hold well on window frames. This option is quite expensive. Domestic window paints are comparatively cheaper.

On average, window repair and painting will cost from 500 to 10,000 rubles.

Examples of alkyd enamels from Russian manufacturers

• The paint must be thoroughly mixed in a jar, strained on a special metal sieve into a bath.
• The first coat of paint is more watery than subsequent ones, because its purpose is to impregnate all the unevenness of the wood.
• To dilute, use a thinner or white spirit, see paint composition.
• After the first application, the paint must dry. And only after that you can start painting on the second layer.

As a rule, windows are painted in three layers, although sometimes two layers will be enough.

It is worth noting that the second and third coats of paint should be thicker to avoid subsequent streaks. If they do appear, it is urgent to remove them with a rag and solvent. If this is not done in time, later you will have to re-clean and paint the entire surface of the frame.

When painting, do not dip the entire brush into the paint, only half, leave the excess paint in the bath, gently brushing along the edge. Start painting with outer side window. It is important to have several types of brushes: small ones for more hard-to-reach places, large ones for smoother surfaces. The width of the brush varies from 3cm to 5cm. A flat-shaped brush is suitable for painting frames.

The paint will lie perfectly along the grain of the wood. Paint the corners with light, short brush strokes.

Another important note - remove the adhesive tape and newsprint from the glasses before the paint is completely dry. If this is not done in time, the paint layer may be damaged.

We install the accessories removed earlier after the wooden frame has completely dried.

If you have been thinking about how to paint a window correctly - with your own hands or with the help of professional craftsmen- after our article, all questions and doubts will disappear. Have a good repair!

Where to buy paint? What price?