How to get rid of toning: a few simple tips. How to remove glue after tinting

In fact, the reasons for removing the tint can be very different. This may be another tightening of liability for unauthorized tinting or simply a poorly applied film on a car purchased on the secondary market. In any case, in order to save time and money, it is worth understanding in detail the methods and nuances of removing tinting from car windows.

Methods for dismantling the tint film

A simple and logical way to remove tinting can be to contact a car service, if not for the prices for these services. After raising fines for tinting, a stream of people "tone out" increased several times, which led to an increase in prices for this seemingly simple work.

Therefore, the question of removing tinting with your own hands has become relevant.

It should be noted right away that removing the film from the glass - not an easy task. To make the glass transparent after removing the tinting, without glue residues and pieces of film, there are 2 ways:

Heating method;

method without heating.

Film removal with glass heating

The film heating method is based on drying the adhesive at high temperature and then removing the tint without any residue on the glass. (The adhesive loses its properties when heated, and the film easily moves away from the glass)

For quality work you will need:

1. Hair dryer or other similar device with the ability to heat the surface up to 40 ° C.

2. Assistant to remove the film from the surface before it has time to cool.

The work process is simple:

One person heats the glass surface, after which the second person carefully peels off the film. Peeling off should be smooth, without sudden movements, otherwise glue and pieces of tinting will remain on the glass surface.

This method is reliable, but requires precautions.

It is necessary to avoid prolonged heating of the plastic or rubber elements of the car adjacent to the glass, as they may be damaged.

With a sudden change in temperature glass can break, so the dismantling of the film is carried out at a positive temperature.

At 40°C glue loses its properties, and the film has not yet begun to melt, it is because of this that it is important not to overdo it with heating.

Removing the tint film without heating

This method is more laborious, but it can be used, being without an assistant and special devices.

1. You need to start from the edge of the glass, where you need to pick up the edge of the film with a sharp object, and then slowly peel it off the surface. The area where the film has been removed is immediately coated with household detergent to soften the adhesive and film residue.

3. If the glue does not lend itself household chemicals, then you can use a solvent or acetone. But we must not forget about plastic and rubber, which can suffer from such exposure. Care must be taken not to damage neighboring interior elements.

Features of removing tinting from the rear window

Most rear windows are heated. These are thin threads that are glued to the surface of the glass, and removing the tint in these places is fraught with possible damage to the heating device.

Cold dismantling of tinting is unsuitable here.

It will be more efficient use the method with heating the surface with a hairdryer. Only when peeling off the film in the places where the heating threads are attached, it is necessary to develop special care. The possibility of breaking the heating filaments is great, therefore it is more reliable to entrust the removal of tinting from the rear window to a specialist.

It's no secret that having tinted windows on your car has become so popular that the tinting service is now considered the most popular in car services throughout the country. But, no matter how hard the experts try, the shelf life of such a fashionable chip is limited, and the time comes when the film has to be removed.

automotolife.com

When to remove the old tint

Remove tint for the following reasons:

• improper use of tinting;
• unfavorable natural conditions;
• and, an important fact - the tightening of fines for tinting car windows;
• you bought a car and you do not like the presence of tinted windows.

And this is where the problems begin: it is difficult to remove the tinted film completely, the resistant glue with which the base is impregnated leaves unpleasant and sticky stains. But there are several ways to clean glass without consequences.

First, let's figure out when you need to remove the old film:

1 – if there are reasons that do not depend on the state of the tinting itself, this is light transmission below 80%, which is prohibited by the traffic regulations;

2- deterioration of tinting– delamination along the edges of the glasses, the appearance of bubbles, glue, scratches and elementary burnout of the coating

If you decide to remove the film yourself, you should be aware that this is a painstaking task and requires free time and strong nerves.

For different car windows, you can use several methods for removing tint. Which one is better to use depends on which glass you are going to remove the film from: front, rear or side. With large-scale glass it is convenient to use soap, in small areas - a hair dryer.

Tinting removal options

In principle, everyone chooses for himself more convenient way removal:

• detergent (preferably for the front glass) – to do this, you can use a special car shampoo, dishwashing detergent (more expensive brands), or even washing powder. The solution is prepared in relation to 30 ml of the agent per 1 liter of water, mixed and poured into the car washer tank or sprayer. After applying the substance directly to the tint, you need to stop the process for 5 minutes, let the film soak. Then, using a knife, pry off the edge of the old film and gently pull it towards you with a smooth movement. Repeat the procedure until the glass is clean. ;
• with a hair dryer in this case, you will need an assistant : one heats the surface, and the other gently removes the film ;
• with ammonia solution ammonia is applied thin layer for tinting, then the glass is closed with polyethylene (for this better fit cling film). In this state, you need to leave the car for several hours so that the chemical reaction takes effect, and only after that the tinting is removed. After that, the remnants of the film and glue are removed with water and soapy water;
• soapy water – a painstaking, lengthy process, but effective. Wet the entire tinting around the perimeter with prepared water and apply a newspaper to a damp place, do not let it dry for an hour, constantly wetting the glass. After the specified time, gradually remove the tint, rinse the surface again.

Let's take a closer look at the fastest and most best option removal of tint by heating.

To do this, you will need: work gloves, hair dryer, car scraper, and, ideally, a partner. Remember this method can only be used if your car is in a warm room or outside, but in warm weather. If this rule is not observed, then the glass may crack due to a sharp temperature difference.

We take the following steps:

• Prepare the car for the procedure - remove the seals from the windows.
• Take a hair dryer - you can use both building and household ones;
• Start heating the window from top to bottom at a temperature of no more than 40 degrees. This temperature allows you to soften the glue, but if you increase it, there will be an even greater bonding of the surface. Gradually moving from one edge of the glass to the other. Be careful not to damage paintwork car body and interior.
• Release the glass
• Gently grasp the edge of the tint and gently and smoothly pull down
• If the film begins to break, heat the place of separation again until all the tinting is in your hands.
• wash glass
• Dry the surface with a hair dryer.

Removing tint from headlights

If you want to remove the tint from the headlights, then for this type of glass it is better to use acetone or gasoline:

• dampen a cotton pad or cotton pad with
• distribute it evenly around the perimeter, after that, the tinting should peel off the glass without hindrance;
• remove tint;
• wash the headlight with any detergent and dry it.

To avoid damage to the upholstery of the car when using aggressive chemicals, be sure to cover the surrounding surface with rags, otherwise this may lead to metal corrosion or a short circuit of nearby wires.

How to remove tint from heated glass

If you are dismantling the rear window film, do not forget about the heating filaments, in no case scrape the surface with sharp objects, use a soft cloth.

In places where the heating device is held, do not overdo it with a hairdryer, it is better to choose a method without heating the surface. Photo: Drive2.ru

After removing the film, as a rule, there are always stains and sticky adhesive residues. Since synthetic agents are used in tinting, the most effective option their removal is an ordinary warm soapy solution.

Remember, never use different kind cleaners and others chemicals, this can lead to damage to the lamination (scratches and abrasions may appear) of the car glass.

To make glass perfectly clean you need:

1. Take a rubber scraper and scrape off the remaining glue by scraping, you can also use handy tools - a clerical knife and a blade;
2. Spray the surface to be cleaned with window cleaner, wipe thoroughly and clean the window again with a sharp instrument.

If after two procedures you are dissatisfied with the result, then do the following:

1. Prepare a soapy solution, foam the liquid with a dishwashing sponge, and evenly apply to the entire surface of the glass, wait until it dries completely.
2. Dampen the sponge with warm water and wipe the window again, washing away stains and glue residue
3. Wipe the surface dry with a clean cloth and evaluate your work.

You can also use oily products (but only after removing the tint!), Such as acetone, gasoline, kerosene, medical alcohol. Or buy a special spray in the store to remove streaks after removing the tinted film.

Another version of the removal instructions old toning you will find in the video:

Outcome

Which method of removing tint you prefer is up to you, but do not forget the main rule - through trial and error, you can achieve the desired result. In each particular case different method will be optimally useful. If the doubts are so great that you do not dare to get down to business, then trust the professionals.

Car window tinting- it's pretty complex technological process, in which the glass is darkened with a special tint film or sprayed or simply inserted colored glass. Many motorists are wondering how to remove the old tint from the car glass and the new one using improvised means. Therefore, we will try to help them figure out how this is done.

Consider the following questions:

Reasons for film removal

Peeling off the tint film is a very time-consuming process, which must be approached no less seriously than sticking it on. So the methods of removal will largely depend on the reason for which you need to remove the old tint. Since a relatively freshly glued film is much easier to remove than an old one. And so we will get acquainted with the most common reasons for its removal.

Reasons for film removal:

What are the ways to remove tint

Of course, ideally, in order not to fool around with removing the film, you can use a special service in a car service. But the price has recently jumped to the impossibility that it is easier to do everything yourself. Many car enthusiasts mistakenly think that it is very easy to remove the film on their own, and they are very mistaken. Since in order to do this qualitatively, you need to know a few important points, which will be discussed further.

Therefore, consider ways to remove the tint film:

1. By heating with an industrial hair dryer or steam generator.
2. No heating with soapy water.
3. With the help of ammonia.

You can use any of these methods to remove the film from the windows of your car.

Another very important role is played by the manufacturer of films for tinting. Opinions about Chinese tinting differ, someone says that it is poorly removed, and for someone it does not hold at all. For example, according to consumer reviews, Chinese film quality is much worse than that of other manufacturers. Therefore, to the question of how to remove the old Chinese tint, the answer is obvious, much more complicated, longer in time and more fuss than with the usual one, especially if it is also ancient. In all other respects, you need to act according to the generally accepted algorithm.

Removing tint with heat

How can you tear off the old tint, you ask. For, to remove the old tint film you must first prepare the necessary tools, such as: industrial or household hair dryer, although for heating it is possible to use steam generator or others Appliances which can radiate heat (in some cases they manage to heat even with an iron).

Using industrial hair dryer desirable do not overdo it so that the glass does not burst and not deformed tint film not melted.

Removal with industrial hair dryer

Removal with a steam generator

Precautions when warming up the film must be observed due to the fact that then it will not be so easy to remove it, you will have to scrape it off. And for safety reasons, we recommend removing all decorative elements.

With a steam generator film can remove much faster and better, because hot steam is supplied to the nozzle under pressure. This allows not only to remove the film, but also the adhesive layer. It should be noted that this method, although quite effective, is not safe, since the steam generator is operating at a very high temperature, which can threaten not only glass, but also your own health.

1. First of all, you need to warm up the film thoroughly so that it effortlessly lags behind the glass without leaving a layer of glue, although if it remains, it does not matter, then it can be removed additionally, the main thing is that the film is faked with a blade.

   Important! During operation of the hair dryer, make sure that hot air does not get on the rubber and plastic parts interior, so as not to damage them.

   

   Removing tint from car windows

2. Second important point when removed is temperature regime, it should not be different, because temperature fluctuation can adversely affect the glass, as a result, it will begin to crack, so it is better to carry out such work in the warm season. Experts recommend heat glass up to 40˚С, exactly at this temperature, the glue will become soft and the film does not melt.
3. After warming up with a knife, you need to carefully pry the film around the edges, trying to remove it in this way, you need to act slowly, because glue particles may remain on the glass, which later will need to be washed with detergents.

To more clearly understand how to remove the old tint, below you can see the video instruction.

Removing tint without heating



The question of how to remove the old tint without a hair dryer is asked by those motorists who do not have such a tool. And their first mistake is the very idea that if the edges of the film have peeled off, then it will be much easier to remove it than in the opposite case. Sometimes the easiest thing you can do is just pull on the protruding part of the tint, which will later just come off and leave no pieces of film behind for further removal, which will mean that the material that held it to the glass has simply dried up. Lest this happen use dishwashing liquid, because they are probably in every home. Also, in addition to detergent, you will need a sponge or rag. small sizes, it needs to wipe the stains on the glass, you also need a blade or scraper to pry the film.

If the film adheres well to the glass, then you can simply “cut” it with a sharp blade.

In order to get rid of the old tinting with soapy water, without using heating, you must:

1. Prepare your detergent, which must first be diluted with a small amount of water (24-40 ml of product per 1 liter of water). Ready solution must be poured into a sprayer for more convenient use. They need to be sprayed directly on the inner edges of the film so that the layer gradually comes off the glass.
2. Then, we begin to pry the film with a blade, at a very sharp angle to the glass trying not to hurt her. If a piece of film is pryed up to the moment when it is already possible to pull on its edge, then slow movements you can try to tighten, while the place where the glue was, it is best to moisten with a warm solution. This procedure must be done several times, while giving time for the film to peel off.
3. After the surface is cleaned of the film, it is necessary to apply a detergent and use a rubber scraper to remove the adhesive, which softened under the action of the agent. It is necessary to thoroughly clean the entire surface so that no material remains on the glass.
4. If there is still glue left on the surface, it is recommended to apply special remedy to remove tint. Although with such a task it is good 646 solvent or acetone will cope, they “remove the remains of the adhesive material with a bang”.
5. After applying the funds, you need wipe the glass dry preferably with a clean piece of cloth.



Glass staining with ammonia

By applying this harmful substance like ammonia, you can easily cope with the removal of tinting in any condition, both old cracked and still in good condition, on the side or pasted on the rear window with heating threads. This method of tinting the rear window with ammonia is often used by Americans, since it is the most reliable and is able to cope with the resistant glue of the highest quality tint films.

Here's what it takes:


1. The surface must first be moistened with soapy water, then with ammonia.
2. After that, you need to attach a small part of a plastic bag for collecting garbage to it, on which ammonia must also be applied from the spray gun. It is recommended to work in a respirator.
3. Attach the same piece of polyethylene to the inside of the glass. After that, you need to leave everything for a while, in order to wait until the heat of the sun's rays warms up the polyethylene. Under the influence of heat and ammonia, the film will begin to deform and peel off the glass.
4. Then it remains just to remove the film along with the plastic bag.









The disadvantage of this method is that it can only be used in sunny weather. As a rule, after removing the film, glue remains on the glass, it must be cleaned additionally, for example, with a soap solution and a blade. After all the operations performed, it is advisable to wipe everything thoroughly with a napkin.

How to remove the tint from the rear window without damaging the heating

Removing the tint film on the side windows is much easier and faster than doing it on the rear, especially if it is still heated. Therefore, we will pay special attention and tell you about the nuances of how to remove the tinting film from the rear window without damaging the heating, trim in the cabin and decorative panels. Let's uncover a few tricks.



Rear windows in most cases are equipped with heating in the form of special thin threads. So while removing the film from the glass, no need to make sudden movements because it can damage heating elements. To avoid negative consequences when removing the film warming up will help. and use soapy(alkaline) solution. Therefore, if a hair dryer is not available, it is quite simple turn on glass heating. Under the influence of heat, the adhesive will become softer and can be easily removed from the glass without damaging the heating filaments.

It is allowed to heat the glass with a hairdryer at temperatures above 0 degrees, otherwise it may burst. Therefore, it is not recommended to remove tinting in winter.

Another simple and reliable method get rid of tinting on heated glass - use the ammonia removal method (described above). Or even plain soapy water using food film. But spraying water and gluing the film on top will delay the removal of the tint for a couple of days (this is how long it takes for the water to penetrate the film and it comes off).

As you can see, everything can be done with your own hands, if you just be attentive and careful to your vehicle. If you follow all the steps strictly according to the instructions, then you will not damage anything in the car, but if this process still seems difficult for you, then it is better to turn to professionals, but then you will have to spend 2-3 thousand rubles.

How to remove leftover adhesive from glass

If you made some mistakes when removing the film, then a sticky layer of glue may remain on the glass. To cope with it on your own, you need to try very hard.



1. Water. With it, you can soak the remaining glue, but if it sticks very well, then water in this case may not help.
2. Solvents. This is enough good way but quite dangerous. Do not use substances with high concentrations, such as acetone, which is very aggressive to glass surfaces.
3. Petrol. Before applying to glass, where the adhesive remains, it should be diluted with water. Also see do not make rainbow streaks.
4. Alcohol. The best of all ways and not so dangerous. It perfectly copes with the adhesive surface and removes excess without harm to the glass.
5. Ammonia. Copes very well with repair (construction) glue. It removes the tint along with the adhesive, but you need to be careful and protect other surfaces of the car from ammonia. After removal, it is necessary to wipe the glass well with alcohol.

Thus, you can remove the remaining glue from the glass after removing the tint film with a spatula, but before that, it is imperative to moisten the places with glue residues with soap or another solution from the list presented.

Few people know, but the remnants of glue, both from tinting and other stickers, are perfectly removed with WD-40 universal grease.

As you can see, the procedure for removing tinting is not a simple procedure, so if the darkening of the film on the windows of your car is within allowable norms and I would not like to regularly remove for re-gluing, we recommend that you follow a few tips.

How to care for tinted car windows

If you want tinting to serve you for a long time, then you need to follow some recommendations for its care.:

1. Not recommended leave the car windows open for 5 days after you tint the windows.
2. Not need wash inside glasses for up to 3 weeks after gluing the film, this is done so that the adhesive layer adheres well to the glass.
3. Try do not touch the edges of the film on the glass so as not to damage them, so that later it does not start to peel off.
4. After each sinks is absolutely necessary wipe the glass leaving no water.
5. During glass cleaning do not use brushes so as not to damage the tint.
6. Do not apply special detergents that contain ammonia.
7. Film can be cleaned any hand wash only in the ratio of 30 grams of the product per 1 liter of water.

Caring for tinted glass is simply necessary, if you do not pay special attention to this, then your film will quickly become unusable and, as a result, it will need to be replaced, which will negatively affect your budget and nerve cells.

As you can see, the methods of removing tint films from car windows are quite different. And removing the tint film is no different from the one on the body. Therefore, in order not to harm your car, you need to be extremely careful when removing them. Also, when buying a film, you should pay attention not only to the cost, but also to its quality, because the duration of the service and the difficulty of removing the tint will then depend on it.

The need to remove the tinting from the glass began to manifest itself very clearly after the adoption of the law on the light transmission of the windshield and front side windows in the car. The requirement to remove the tinting forced literally a week after its adoption to make a queue at car services, which became much larger. To comply with this law or not - each driver decides for himself, however, tips on how to properly remove the tint yourself can be very useful.

How to remove tint from glass yourself? To get started, you should get some tools that will help solve this issue without problems for your car. Among necessary tools you can note:

• spray;
• knife for cutting paper;
• scraper;
• building hair dryer;
• rag;
• liquid detergent;
• medical alcohol or ammonia solution.

There are several ways to remove window tint. old film even the High Quality can be removed using one of the methods. If one person can use an ordinary knife for this activity, others should use the full range of tools offered to them.

Removal of tinting can be carried out independently different ways. All of them depend on the quality of the tinted coating and the skills of the person carrying out this process. But still, before you start work, you should prepare your car. The main task at the preparation stage is to open access to the entire surface to be treated. To do this, fluid access must be blocked in the cabin.

The preparatory stage includes the study of the window module and the dismantling of the parts sealing the window. With this procedure, we advise you to remember the order of placement of such overlays and seals well, since there is a high chance that you will soon have to install them in place. How to remove tint from glass with and without heating - we will talk about this later in our article.

with heating

How to remove old tint with heating? For this procedure, you will have to invite an assistant to simplify the process. And you will also have to prepare some tools.

by the most necessary device to remove the tint can be called an industrial hair dryer.

The work has its own sequence and if you stick to it, the process will be carried out correctly and in a short time.

1. One of the people performing the task heats the glass. The other person gradually removes the film.
2. It is very important to monitor during the heating process that hot air does not get on the rubber seals and parts that are part of the fasteners or parts of the interior of the cabin.
   Tinting can be removed if the temperature outside is positive. This will protect the glass of the car from possible cracking.
3. The surface heats up to forty degrees. This temperature softens the adhesive, and the film does not begin to melt yet.
4. After heating, the edge of the tinting is pryed off with a knife blade, and the film is pulled over the exfoliated part of it. We do not recommend forcing and accelerating the robot, because thin material may break. And the remains of the glue will remain and they will have to be removed again in a different way.

How to remove tint from glass using heaters? You can use household appliances such as a hair dryer, steamer and others that can be found in everyday life.

No heating

How to remove the tint yourself without heating the surface? The tint film can be removed without heating, and the process is not very complicated. Several stages, performed in turn, will help to cope with the task without problems and delays.

1. Prying the edge with a sharp object, the old tinting slowly comes off.
2. The glass surface without tinting is cleaned with household detergent.
3. A rubber scraper is needed in order to remove glue stains that can soften significantly after previous processing. We work from top to bottom, the glass is cleared across its entire width. You can also use a scraper to remove the remnants of the tint film.
   If the adhesive is not completely removed, then a more powerful detergent can be used for this. In this case, even acetone is suitable for the procedure.
4. After completing all cleaning procedures, the surface is wiped dry, for this we take a cloth or soft rag.
5. In order to protect the door trim from getting liquid under it, a rag should be placed over the seal. All rubber seals that do not get wet during operation will remain elastic and resilient.

Removing glue residue

It is not often possible to remove the tint yourself and remove the film in such a way as to remove all the remaining glue. Most often, glue residues are removed with a detergent, and a sponge or cloth acts as the main tool for work. If the glue stains are held more confidently, then they can be removed with a scraper.

But still, before the procedure for removing tinting, moistening the work area with detergent will not hurt. The most difficult cases of contamination can be cured with acetone or gasoline mixed with vinegar. You should not allow such combinations of caustic substances to get on the upholstery of your car.

Nuances when removing tinting from the rear window

You can remove the tint yourself from the rear window of the car, but this requires more care and accuracy. Usually, heating threads are located on the rear window of a car, which are very easy to damage with careless movements. You should also be careful not to scratch anything.

Any way to remove tint from the rear window must have a previous procedure for heating with a hair dryer. Remove the coating with solvents is not at all The best way. Softer tint removers can keep your vehicle intact and safe. The requirement to remove the tint applies both to the front windshield, as well as to the rear. The removal procedure should take place in comfortable conditions, and the temperature outside should not be below zero - this can damage the glass even without heating it.

Video "How to dismantle the tint film on your own"

This video shows how to dismantle the tint film on your own.

Car window tinting is a complex process. technological work requiring a certain amount of skill and specialized equipment. Tinted glasses create certain conveniences and comfort, but there are situations when this tint layer needs to be removed. And before you remove it, you should read the recommendations on how to remove the tint yourself quickly, easily and efficiently.

Why do you need to remove tint from car windows?

tinted windows– it is certainly convenient. The cabin will not be so hot in warm weather, the sun's rays will not blind the driver and passengers. In addition, it is a certain protection from prying eyes. However, there are certain reasons why tint removal cannot be avoided.

• Protective glass coating over time wears out, scratches and other larger defects appear on it.
• Often car owners notice that under the film bubbles form. The reason is not following the technology of applying the film on the glass surface.
• After purchasing a car with tinted windows, the owner notes that he uncomfortable ride with too dark windows, or, on the contrary, he is not satisfied with the increased light transmission, and he wants to install a darker film.
• Removal of tinting may be due to traffic police requirements. According to the requirements, the light transmission capacity of the glass surface when applying the film should not be less than 75%.

In order not to pay significant fines every time a traffic police officer stops you, it is better to remove the tint layer.

How to remove tint film from a car

We will immediately make a reservation that this work can be entrusted car service worker. But, if you want to save money and like to tinker with your car, you can remove the tint from the glass on one's own. Exist four effective ways how to remove film:

1. By heating the surface with a hair dryer or steam generator.
2. Using soapy water.
3. mechanical way.
4. With the use of ammonia.

Removing tint with heat

Thermal removal applicable in warm weather, such as in summer or when work is carried out in a heated garage. To remove the old tint from the windshield or side glass, you need to prepare household hair dryer or steam generator. A hair dryer used for construction purposes must be used very carefully, since at too high temperatures it is likely that the glass surface may burst, or the film will melt and flow over the glass. Removing it in this case will be much more difficult.

As practice shows, steam generator it is more convenient and faster to work, the film not only quickly lags behind the glasses, but is also immediately removed adhesive layer. But when using a steam generator, it is also worth considering safety precautions. This appliance generates and delivers steam under high pressure, you must work very carefully so as not to burn yourself. When working with hair dryer and steam generator it is necessary to ensure that hot air is not directed for a long time at the plastic and rubber elements of the interior, which can be deformed under the influence of hot air.

It is more convenient to carry out this procedure with a partner: one heats the surface with a hair dryer, and the other begins to dismantle the film layer.

Procedure, how to remove film by heating:

1. Surface heating. It is necessary to turn on the device and direct warm air onto the film. At a temperature of +40 degrees, the tinting will begin to move away from the glass.
2. Coating Removal. With a sharp object, such as a blade, you need to pry off the edge, then gently pull the material.
3. If after removing the coating on the glass surface adhesive layer left. Glue is removed with warm soapy water or solvent.

Removing the film with soapy water

In order to remove tint properly, you need 30-40 ml of any liquid detergent, it is dissolved in a liter warm water. The resulting solution is poured into a spray bottle.

How to properly remove tint:

• Spray with soap at the edge of the cover.
• Once the edges start to come off, continue splash water on the inner adhesive layer of the film. If the edge does not come off, it can be slightly pry with a blade.
• Slowly and very carefully start peeling off the tape while constantly moistening it with water.
• When cover will be completely removed., start to removing the adhesive layer. The glass is moistened with the same soapy composition and the remaining glue is removed with a scraper. If the soapy solution is not effective, and glue clots are still present, they can be removed with a solvent or acetone.

Sold in car dealerships special means to remove tint, using them, you will quickly complete the entire operation.

Removing tint with ammonia

One of the most efficient detonation methods - use of ammonia solution, and this option is suitable even to remove the old coating and coating from the rear window where there are heating filaments.

You will need: ammonia, soap solution, sprayer, black plastic bags and respirator.

Work order:

1. Spray on glass surface soap composition.
2. Wet the surface ammonia.
3. Cover the tint with polyethylene and top spray again with ammonia, leave for a while. Under the action of sunlight and ammonia solution, the coating will begin to lag behind the glass.
4. If a film began to wrinkle, it can be removed.

Glue is removed with soapy water or any solvent.

Film removal by mechanical action

If the tint coating is not old, you can try to remove it using blade or sharp thin knife. After the seals are removed, the edge of the film material is pryed off with a blade and at the same time pulled towards itself. These steps must be carried out until the film is completely removed. This will require patience, quick actions can provoke a tear in the film.

After removing the film coating on the glasses remain glue residue, they are removed with a soapy composition or solvent. It is not worth rubbing and applying force, it is enough to moisten a rag in a solvent and leave it on the glass surface, after a while the glue dissolves, and you just have to wash the glass and wipe it dry with a soft cloth.

Another way to remove Chinese film without using any tools and devices. For this it is necessary dismantle glass, lower it into the bath and pour very hot water. The film itself will lag behind the glass.

Removing tint coating from glass with heating threads

Technological process tint removal from the rear window, where there are heating threads, is distinguished by its own characteristics. Careless actions can damage the heating elements. To remove coatings from the rear window, you will need an alkaline soap solution, in this case you can not use a hair dryer, but simply turn on the glass heating. It is impossible to scrape off the glass surface in order to quickly remove the film, firstly, this way you can scratch the window itself, and secondly, you can damage the heating filaments.

Removing tint film from headlights

On one's own remove film from headlights can be done in the same way as with windows. If the tint layer was applied with paints and varnishes, the algorithm of actions is somewhat different. Headlight surfaces need to be sanded. For this, it is applied Sander or sandpaper with an abrasive layer, first 2000, then 3000. Headlights are polished until the tint is completely removed. Before starting work, it is necessary to glue the joints of the headlights and adjacent surfaces with masking tape.

After reading the instructions and helpful tips, you can choose for yourself suitable option removing tint. The main thing is to prepare in advance the right tools and funds, be patient and carefully do all the work.

There is also a video on how to properly remove the tint.