Installation of plasterboard partitions Knauf. Knauf: description of the installation technology and the materials required for this

Content:

One of the most effective methods ceiling alignment is mounting plasterboard ceiling by Knauf technology. This method takes quite a bit of time and effort, but the result is excellent. This method is a sequential assembly of finished structural elements.

Let's take a look at what is included in the proposed kit:

Guides.
Profile 28X60.
Various hanging items.
Crabs.
Profile connectors, they will be required only if the profiles are not long enough and they have to be increased by connecting them together.
Ceiling drywall Knauf.
Fasteners (dowels, bugs and self-tapping screws).

Preparatory work

Installation work should be carried out during the period finishing works indoors, the Knauf GKL ceiling installation technology is applicable only if all wet work has already been completed. Also, before starting work with the ceiling, it is worth aligning everything vertical surfaces. Indoors, it is worth keeping normal room temperature and humidity. In no case should the temperature fall below 10 degrees Celsius.

Before starting work, it is worth preparing the tools:

perforator;
cordless screwdriver and drill;
tape measure and pencil;
knife for processing ends;
hydraulic level.

Marking and fastening guides

To mark the ceiling, which will be mounted using Knauf drywall technology, it will not be enough to use building level, for this purpose, a hydraulic level or a laser device is ideal. It is also worth preparing a paint pad. After marks were made in the corners of the room using the hydraulic level, they are connected to each other around the entire perimeter with a cord.

Fastening metal profile will be carried out under the intended line, so it is worth remembering that the final floor will go down the width of the profile and the thickness of the drywall sheet. This point should be thought out in advance so that, ultimately, the ceiling does not fall too low.

At the marking stage, it is worth looking at the ceiling and walls for the presence of electrical wiring, it is recommended to outline its location. This will prevent damage to it when attaching the metal profile frame.

After all the markings have been done, it is worth fixing the guides; for this purpose, a 27 by 28 mm profile is used. They are attached to the wall with dowels 6 40 mm.

Frame installation

Knauf technology involves directly on the frame. After fixing the guide profiles, you can begin to mount it. It is necessary to fix the suspensions along the pre-planned lines. To attach them to concrete base dowels must be used. For the frame, the Knauf profile 27 by 60 mm is used. The recommended distance between the profiles is 40 cm. When all the profiles are installed, you can begin to mount individual pieces of the profile, which will run perpendicular to the main ones.

On a note: In order to connect the elements at a right angle, it is necessary to use a special connecting profile - "crab".

It snaps onto the profile, but for reliability and strength, it is also attached to the profile using self-tapping screws measuring 3.5 by 9.5 mm. IN finished version a frame with a cell size of 40-40 cm should be obtained. The final stage of mounting the metal-profile frame is leveling the surface and fixing the hangers. It is with their help that you can adjust the horizontal plane of the suspended ceiling. Suspensions should be located at a distance of no more than 50 cm from each other. If there are more of them, this will only improve the strength and reliability of the profile structure.

Installation of drywall on the frame

Great difficulty in fastening drywall sheets there is no ceiling, the Knauf ceiling GKL installation technology is very easy to perform. But to create more comfortable conditions work is worth asking for help, since drywall sheets have enough big sizes and keeping them under the ceiling is quite difficult. Before sheathing, it is recommended that you familiarize yourself with the basic rules for the work:

Plasterboard sheets must be fixed in the direction of all profiles with a pitch between the screws of no more than 20 cm. In those places where the sheets are joined, the screws will be offset.
Use a sharp knife to cut a straight drywall piece. After making an incision in the upper layer, the sheet can be broken along the slot. If you need to prepare curly parts for cutting them, it is better to use a hacksaw.
It is necessary to screw in the screws carefully, it is important to control that the cap is slightly recessed and does not protrude above the surface. But you should be careful not to break through the sheet, as the fastening will be unreliable.

Puttying the plasterboard ceiling begins with the finishing of the joints. It is mandatory to use a grid that will prevent cracking of the plaster. Puttying the entire surface is carried out only after the joints have completely dried.

Video about making a ceiling using Knauf technology

Attention, only TODAY!

Tsugunov Anton Valerievich

Reading time: 4 minutes

Drywall is widely used in the renovation of apartments. With its help, walls and ceilings are leveled, niches and boxes are constructed, doorways are modernized, and many decor elements are performed. There is certain rules installation of these structures, which must be observed. Leading drywall manufacturers have developed entire kits for the convenience of consumers. The Knauf technology has gained particular popularity in our country.

Benefits of Using Technology

Knauf produces a whole line of ready-made kits that differ depending on the type and size of the structure.

The main advantage of the Knauf kits: they include everything you need to mount a wall or partition, from drywall to fasteners. This provides the consumer with several benefits, including:

Guaranteed to use only high quality materials. This is facilitated by a strict system of company control, designed for minimum tolerances in the manufacture of plasterboards and other elements.
Ease of calculating the consumption of drywall and other parts of the structure. A simple online calculator available on many sites is enough. You need to enter the dimensions of your wall or partition into it, indicating the number of doors and windows, and it will give full list all necessary elements indicating their number.
Each set is supplied by the manufacturer detailed instructions for assembly, thanks to which even an unprepared person can carry it out.
Buying materials separately, you can forget some details. Using the kit solves this problem.

The procedure for installing Knauf kits

Required preparatory work: alignment and marking. After that, a partition is placed:

Guide profiles are attached to the dowels.
Through the selected optimal intervals are set vertical racks. Their fixation is recommended to be done using a cutter with a bend.
Horizontal jumpers are mounted.
If necessary, communications are stretched, insulation is laid.
GKL frame is sheathed with special proprietary self-tapping screws.
Spend finishing corners and joints of sheets.

Mounting Features

The system for assembling walls and partitions using this technology has its own nuances that must be taken into account in order to achieve the optimal result:

To ensure high strength individual elements the frame is reinforced by nesting one profile into another.
The guides are attached to the dowels at least three points. The plane of the profile adjacent to the base is preliminarily pasted over with a damper tape.
Often it is necessary to join insufficiently long elements of a metal structure. In this case, you should space out the junctions, for example, place them in a checkerboard pattern. This will reduce the likelihood of vibrations or various deformations of the structure.
Racks are placed at a distance of 600 mm from each other. Thus, each sheet will be fixed on three profiles. If necessary, the step between the racks can be reduced.
The profiles are fastened together with a cutter or branded self-tapping screws. Crab connectors are used at intersections.
GKL sheathing elements are fastened end-to-end with the necessary gaps to compensate for the thermal expansion of the material. Later they are filled special composition, produced by the same company "Knauf".
When building partitions from gypsum boards with window niches or doorways, it is forbidden to join sheets above them. Otherwise, there is a risk of seams coming apart due to vibrations that occur when using windows and doors. Docking of elements is carried out closer to the corners of the room.

Types of structures provided by Knauf

The sets differ from each other in the number of skins, thickness and frame design. All partitions use branded insulation based on mineral wool. There are the following kits:

C 111 - with one layer of sheathing. The minimum thickness and instability to loads do not allow such a design to replace a full-fledged wall, its function is decorative and zoning.
C 112 - sheathing in two layers on each side on a single frame.
Sets C 121 and C 122 are similar to the two described above. The difference is that instead of profiles, they use wooden bars for the crate.
C 115 - a set with a double frame, lined with two layers of drywall. This allows, by increasing the thickness of the partition, to place a double layer of mineral wool in it. According to its characteristics, this design is close to a conventional wall.

C 116 - also performed on a double spaced frame. The internal cavities remaining inside it allow for hidden installation of communications. The two-layer sheathing removed from the wall is implemented in the C 626 kit.
C 113 or C 367 - sets with triple skin. Designed for those cases when it is necessary to apply drywall different types: moisture resistant, fireproof and common in many combinations.
C 118 - used for extra-strong walls and partitions. In it, sheets of galvanized steel 0.5 mm thick are laid between the layers of drywall.
C 361, C 362, C 363 - sets on a single frame, sheathed, respectively, in 1, 2 or 3 layers with Knauf gypsum fiber supersheets. C 365–369 - modifications of partitions with gypsum fiber on different frames.
C 386.1 and C386.2 - kits that provide for the laying of ventilation or other communication channels.

Various combinations of frames and skins are possible. All of them are presented in the Knauf product line.

A single frame is used when it is not planned to hang anything heavy on the wall, and also if significant insulation or soundproofing is not required. But to attach to the wall household appliances, which has a solid weight, you will have to make a double frame with reinforcement.

Features of the formation of corners from drywall

Corners play an important role in the installation of drywall construction. If they are assembled incorrectly, then through a short time cracks will appear in these places, and the fastening of the sheets will be unreliable.

GKL structures can have both internal and external corners. For the formation of each of them, their own methods are used. First of all, the frame is assembled.

External corners are made as follows:

Two vertical posts forming a rib are installed in the rails so as to form a single angle. It is unacceptable to mount them with an offset: in this case, there will be a void under the junction of the drywall sheets.
The racks are fixed in the guides with a pair of self-tapping screws at each attachment point. Professionals prefer to use a cutter: such a connection does not contain bulges that interfere with the tight fit of the GKL.

Fragments plasterboard sheathing are screwed end-to-end, so that the plane of one element overlaps the end of the other, and are reinforced with a special corner profile. You can fix it with putty or PVA glue.

Curvilinear ribs are reinforced with a flexible plastic corner.

Many masters who install suspended ceilings have mastered the technique of work in practice, adopting the necessary experience and knowledge from more experienced installers. But when the work requires the preparation of a project of work, and at the end it is necessary to provide reasonable guarantees technical compliance constructions to the norms of SNiP, many experience difficulties. Masters of any reputable organization perform the design and installation of drywall on the ceiling in accordance with the recommendations contained in the standard routing Knauf.

Purpose and content of the technical map

If for an amateur GOST and SNiP are a “dark forest”, then for a professional, the technological map is a universal guide on how to technically competently and quickly mount the frame and fasten drywall.

This instruction will save the master from studying these very norms and requirements, and will speed up the delivery of work to the customer. If you follow all the recommendations, the work will comply with fire regulations, environmental safety, the requirements of GOST, SNiP.
The Knauf technological map contains tables with ready-made initial data of the main components of the frame structure for the ceiling.

Ceiling Knauf

Important! If the work is carried out under a contract, then when placing and submitting an order, one cannot do without the recommendations of the Knauf technical card for the preparation of project documentation.

The manual states necessary material and an algorithm for assembling a frame of one type or another; ways to perform individual structural tasks are described.

The latest valid Knauf worksheet (series 1.045.9-2.08.1) is comprehensive on how to design and install a suspended ceiling structure for plasterboard and gypsum fiber boards. All work is divided into separate successive stages, so it will not be difficult to understand the technology.

Types of ceiling structures

The frame on the ceiling is made of metal profile Knauf, and from wooden bars.

There are 5 types of suspended ceiling structures:

Ceiling P 111 (the technology is known among the masters as the "system 111"). The biaxial frame is assembled from wooden bars.
Ceiling P 112. Biaxial frame made of metal profile.
Ceiling P 113. Uniaxial frame made of Knauf metal profile.
Ceiling P 131. A frame in which a wall profile is used with fastening not to the base of the ceiling, but to the walls.
Architectural and decorative ceiling P 19. A complex multi-level frame.

Frame guides

For wooden structure P 111 use coniferous bars with a moisture content of not more than 12%. Before installation on the ceiling, they are treated with an antiseptic and flame retardant. The recommended section of the bars is 50 × 30 mm.

The metal frame for the ceiling is made of long rolled elements made of sheet steel.

Frame with fastening to the base (P 112, 113). To assemble it, take a regular ceiling profile. It consists of the following elements:

Guide profile PN. In cross section, it has a size of 27 × 28 mm. There are factory holes in the wall through which the installation to the base of the wall is carried out.
Complete with PN, a supporting PP profile is mounted. In cross section, it has a size of 60 × 27 mm.

The ceiling of the P131 system with fastening to the wall is made of a more powerful profile for the installation of partition structures (PS).

To reinforce the structure at the joints of the premises, a reinforced UA profile is used on the ceiling.

Fasteners

Work on connecting the profile is performed using the following elements:

Multi-level cross connector for PP profile (60×27). It is sold in a straightened form, therefore, before installation, it must be bent.
Single-level cross connector "Crab".
One-way cross connector. With its upper side, it clings to the carrier profile.
Swivel multi-level connector that allows you to connect the carrier profile at any angle.
Longitudinal single-level connector. It is used when it is necessary to increase the bearing profile.
Universal connector. It is necessary in order to connect the carrier profile in one plane at any angle.

The work on mounting the frame on the Knauf ceiling is carried out using the following elements:

Direct U-shaped suspension.

Important! Not everyone knows that U-shaped suspensions are produced under the profile and under the timber. With external similarity, they have a different nominal size after bending the side strips. For wood, it is 50 mm, and for a profile - 60 mm.

Anchor hanger with adjustable clamp, quick suspension. They have similarities due to the presence of a mounting rod. Its length can reach 1500 mm, which allows you to adjust the required overhead gap in a wide range. The disadvantage is the limitation in the load up to 25 kg. This is considered a low figure, since all average calculations in the Knauf data sheet are based on a load of 40 kg.

Adjustable vernier hanger. It is a telescopic design of two parts. Designed for a load of 40 kg.
Combined suspension, in which there is both a rod and a retractable element of a vernier suspension.
For connection metal elements the necessary LN screw (with a sharp tip) and an LM screw (with a self-tapping tip).
Installation of a heavy profile in the P131 system is carried out with FN self-tapping screws.
Mounting the guides to the wall is carried out with metal or nylon dowels.
Mounting to hollow structures in sheet drywall Knauf perform multifunctional dowels or butterfly dowels.
Installation attachments to the sheets is carried out with a dowel with a screw thread.
Drywall is screwed with TN screws (in a standard profile) or TB (in a thick sheet profile). The MN screw is used for screwing into a gypsum fiber sheet.

Types of drywall

Depending on the operating conditions, required drywall Knauf is chosen from the following varieties:

Type A. Regular construction drywall. This sheet is used for heated rooms with a normal level of humidity (up to 60%).

Type H2. Drywall with increased moisture resistance. The sheet has a low level of water absorption (up to 10%). Humidity can be up to 75%.

Type D.F. Gypsum board resistant to open flame.

Type DFH2. Drywall, which has the properties of the two previous types.

Important! Initially, it is customary to calculate the frame specifically for ceiling drywall 1.2 × 2.5 m in size and 9.5 mm thick. But drywall comes in other sizes as well.

Drywall has a factory longitudinal edge. The most technologically advanced and therefore common is the semicircular thin one, but there is drywall with other types of edges:

Sheet with a straight edge.
Sheet with a cut corner.
Sheet with a thin edge.
Sheet with a rounded one-sided chamfer.
Sheet with a semicircular edge.

Each type of edge is needed to solve specific structural problems. In particular, the installation of figured corner ledges.

Work is carried out in a dry and heated room at an air temperature of at least +10 degrees.

Work on the implementation of any frame begins with marking the design position of the ceiling surface. Using a level and a chopping thread on the walls around the perimeter, mark the corresponding line.

Further, depending on which Knauf drywall is selected for the suspended ceiling, work is carried out to mark the location of the guides and mounting points for the suspensions. The lines of the bearing guides are marked in accordance with the length of the sheet so that the end joint falls on the profile.

At the marked points, suspensions are attached to the ceiling with dowels or anchors.

The wooden frame is mounted in two ways:

Mounting the guide rail to the base using a direct hanger or a quick-mount hanger. When using a quick suspension, alternately change the side of attachment to the bar.
Installation of the guide bar with anchor dowels directly on the ceiling. At the same time, in places of differences in the base, linings are used.

Mounting the frame from the profile:

The P112 ceiling is mounted in the same way, only in order to connect the guide and the supporting profile, two-level suspensions are used. When cutting guides, a compensatory gap of 10 mm is made. It will prevent deformation of the surface with temperature changes.
Installation of a single axis Knauf systems P 113 differs in that the technology provides for laying a sealing tape under the guide profile.
The work on assembling the P 131 system differs from that described above in that a wall profile is used, and the installation of the guides is carried out along the long wall of the room. These structures are usually mounted under a heavy ceiling, so necessary step dowel fastenings - no more than 30 cm. Guides use only solid ones. The carrier profile must be at least 3 cm into the guide.

Fixing drywall sheets

Important! The edge of the sheet, not pasted over with cardboard, is processed with a planer in order to chamfer.

The manufacturer has prepared a video in which the craftsmen demonstrate the principle of assembling a suspended structure

Screwing work sheets Knauf performed in pairs or using a lifting mechanism. Drywall is mounted on the ceiling without T-shaped joints, apart. At the same time, the sheet is shifted by a step of the carrier profile. Installation is carried out so that in the longitudinal direction the sheet lies without a gap, and in the transverse direction a small gap is obtained. So the putty will completely fill the joint, and the seam will turn out to be strong.

With temperature changes, the drywall sheet expands, so in large rooms it is necessary to provide for expansion joints in increments of 15 m.

For the convenience of puttying self-tapping screws, they are twisted with a slight recession of the cap into the sheet - by 1 mm. Work on sealing joints is carried out using reinforcing tape.

Drywall is a universal material, and the Knauf technological map will help to perform high-quality installation of any design, even for a novice master.

Drywall, by right, is considered universal material which is convenient to use, does not require constant and complex care, and most importantly, can be used to form simple and complex elements when decorating a room. With the help of drywall, you can sheathe the arch, partitions and niches, suspended ceilings.

On the other hand, drywall sheets are not the most important thing when decorating walls in a room. In this case, you can not do without a solid frame. Knauf-partitions - this is exactly the option that is perfect for decorating walls with drywall. Let us consider in more detail what a KNAUF-type plasterboard partition is, as well as what activities are carried out in connection with the installation of this finishing option.

What is a Knauf partition and what types of construction are there?

Partitions made of Knauf plasterboard, in fact, are a conventional plasterboard structure, inside of which there is metal carcass. Used to create a frame robust profile. Partitions are highly durable and quite easy to assemble.

The assembly of structures takes place according to a special technology, which allows in the future to exclude various unforeseen circumstances and problems associated with the operation of partitions.

GKL partitions made according to the KNAUF system can have different kind. They are installed in rooms with different levels soundproofing and with different purposes. Structures can be of different types and are divided according to various parameters.

Partitions are:

with one layer of skin;
with two layers of skin;
with three layers of skin;
with one layer of sheathing, made of moisture-resistant Knauf supersheets, on a single-type frame.

Important! If you want to make strong walls in the room and elevated level sound insulation, it is necessary to use partitions with a double frame.

In addition to the indicated varieties, there are partitions where special ventilation ducts and communications are built. Another parameter worth paying attention to is the type of frame structure. On this basis, the frame can be double and single.

The technology of mounting partitions with a double frame provides for the creation of a strong, reliable wall that can withstand even a heavy TV or other furniture that has a significant weight.

Single-frame constructions have a more affordable cost and are used in rooms where an increased level of sound insulation is not required, and heavy objects will not be placed on the walls.

Advantages of Knauf drywall partitions

Plasterboard partitions made according to the KNAUF system appeared in the 90s and today have taken a strong position in the market finishing materials. Drywall today is strongly associated with the word "European-style renovation", because it allows you to create a neat, beautiful and inexpensive finish in a room in a short period of time. The Knauf company was able to improve the quality indicators of the material and create structures that became not only a stylish, neat design in the room, but also distinguished by increased strength and reliability.

Material such as Knauf drywall is considered a durable and durable material that is easy to use.

The main advantages of Knauf partitions are as follows:

installation of partitions can be done independently, without the involvement of specialists. The package includes detailed instructions;
calculate right amount materials is quite simple with the help of a special construction calculator online. The expense is determined by taking into account the working area of the premises and the type of decoration that will be performed;
The assembly kit includes a sufficient number of parts needed to assemble the partitions. The contractor does not have to calculate materials using a calculator;
kits allow you to quickly and easily assemble the partition;
the material is highly durable and can withstand even a strong earthquake.

The use of Knauf partitions is very popular today, and in addition to ease of use, buyers note the affordable cost of such structures.

The process of assembling partitions according to the Knauf system

This method of installation does not have any special differences with the standard technology for finishing plasterboard. However, some differences still exist.

When laying Knauf drywall, it is important to ensure that there are no cruciform joints.

IN standard kit includes top and bottom rails, as well as racks. The width of the racks can be different and depends on the height of the room where the finishing will be carried out, as well as on general view structures.
To fix the guides, it is recommended to use special dowels, with which you should fasten at three points.
When mounting the posts, it is important to take into account the distance of 60 cm. In individual projects, the spacing of the posts can be reduced.
The main method of fastening the racks is the “cut-out with a bend” technique. Here it is allowed to use special KNAUF self-tapping screws;
To increase the level of sound insulation, you can use mineral wool.
When installing sheets, it is necessary to use the “butt” technique so that the laying is carried out without a gap.

In addition to these recommendations, it is important to take into account the features of mounting the frame. For the system to work long time, it is worth paying attention to the joints that are above the doorway and are not located on the racks. All of these recommendations will allow you to cope with the installation of the structure in the shortest possible time.

Conclusion

Partitions made according to the Knauf system can be an ideal option for planning a room and finishing it. To calculate the required amount of material, you can use a special calculator, or you can use ready-made kit. Using this finishing option, the user will receive a neat, modern and aesthetically attractive room.

Drywall is used to create arches, various decor rooms, partitions, wall openings, etc. Creating beautiful decorative elements will not do without a strong support, which is the Knauf-partitions. What is a Knauf partition? In fact, she looks like drywall construction, in which the frame consists entirely of a metal profile. The design is created using a special technology that excludes various unforeseen circumstances.

Partitions Knauf can be different. They are installed in various premises, with different sound insulation, for different purposes. Partitions can be of different types and are divided according to certain parameters.

According to their design, partitions are divided into:

Partitions with one layer of sheathing;
Partitions with two layers of sheathing;
Partitions with three layers of sheathing;
Partitions with one layer of sheathing, consisting of moisture-resistant Knauf supersheets on a single-type frame.

In addition to these types, there are partitions with built-in special channels for ventilation and communication. The next parameter by which the partitions are divided is the frame, or rather its type. Frames can be double or single.

The use of partitions based on a double frame is recommended if you need to create a strong, reliable wall that can withstand a heavy one.
The creation of partitions with single frames is recommended in places where sound insulation is not so important, and the walls will not be burdened with heavy pieces of furniture or appliances. It can be concluded that the double frame is more durable.

Knauf drywall partitions: main advantages

Why is drywall and Knauf partitions so popular? Since the 90s, drywall has been almost synonymous with the word renovation. On the Russian market this material appeared thanks to the firm Knauf. The material was accompanied by instructions that explained in detail how to create various designs from plasterboard sheets. The technology has gained great popularity due to the excellent quality of the product.

The main advantages of Knauf drywall partitions are as follows:

Installation of partitions can be carried out independently without the involvement of specialists; detailed instructions are included in the product;
Very easy to calculate required amount material and its cost;
Each set has the required number of parts, it is impossible to forget anything;
The kit will provide a quick and easy process of creating a partition;
Knauf material is very durable, so that the partition can withstand even an earthquake.

The use of Knauf partitions is popular to this day. The correct selection of a set of partitions can provide excellent sound insulation, high strength and reliability of the walls. As mentioned above, there are different strengths and sound insulation, depending on the type of room, you should choose the right kit.

Installation technology of partitions made of drywall Knauf

The installation technology according to the Knauf system is not much different from the standard installation procedure. However, there are still some differences, which will be discussed below. Together with the drywall material, Knauf brought special technology and general recommendations for the installation of partition walls.

They look like this:

Each baffle set has top and bottom rails and posts. These racks can have a different width, which depends on the height of the room where the installation is supposed to be, as well as on the weight of the overall structure.
To attach the guides, it is recommended to use dowels, it is necessary to fix at least 3 points.
To install rack profiles, a distance of 600 mm must be observed, in some cases the distance can be reduced.
To fix the racks, you should use the “cut-out with a bend” method, it is allowed to use special Knauf self-tapping screws.
To attach the device to a suspended ceiling, the fire rating must be met.
Mineral wool can be used for soundproofing.
For mounting sheets, use the "butt" method, that is, lay them without a gap.

In addition to the above recommendations, it is necessary to take into account the features of the installation of the frame. In order for the entire system to serve for a long time, it is necessary to ensure that the joints from the GKL-partition above the doorway are not located on the racks attached to the box. Instructions for assembling the frame for fastening the GKL in our material:.

In addition, the seam must be made so that it is in that part of the intermediate guide that is above the horizontal beam. The horizontal beam serves as the upper boundary. Compliance with these recommendations will help you make a long-lasting quality design.

High-quality GKL partitions according to the Knauf system: what will affect the choice of kit

Exist different types partitions that fit under different options premises. On the this moment there are about 25 sets for the installation of partitions according to the Knauf system. All sets are marked with the letter "C", which is combined with a specific set number.

To choose suitable set for installation, consider the following factors:

The height of the room or room;
Desired noise level;
Possible load on the wall in the form of furniture or appliances;
Availability of communication systems;
Type of door or its absence;
Desired partition height;
The temperature in the room and the level of humidity;
Type of room and its purpose (bedroom, kitchen, bathroom, living room).

Having decided on the parameters of the room, it will be much easier for you to choose a partition. For example, a bedroom adjacent to the kitchen or living room requires a high degree of soundproofing, so the installation kit should be selected appropriately. If the bedroom is adjacent to the wall of the neighboring apartment, then all the more so the partition should be with a high degree of protection against unwanted noise.

Modern Knauf technology and drywall: walls and partitions (video)

Plasterboard partitions Knauf - worthy and reliable way to build a wall at the desired location. Simplicity and ease of use, installation will help make the installation process easy and enjoyable. With this technology, the issue of excess noise will be closed to you forever.