How to make crafts from polyurethane foam with your own hands. Do-it-yourself garden figures from polyurethane foam (35 photos): tools and materials

Polyurethane foam has firmly won its place in the construction industry. This handy sealant is able to alleviate assembly work and the range of its application is unusually high. But now, more and more often, polyurethane foam has begun to receive unusual use as a material for creating crafts. To figure out how to do this, you first need to know what polyurethane foam is and what features it has.

What is foam and what is it used for?

First of all, mounting foam is effective remedy, capable of providing reliable sealing of seams and the correct position of installed parts in a matter of minutes. In fact, it is a combination of two components: isocyanate and polyol, which are produced from oil. Foam is sold in cylinders, which, in addition to the polymer compound, also include a propellant gas that displaces the mixture from the nozzle. Upon contact with air, the mixture begins to significantly increase in volume and polymerization of the substance occurs.

Initially, foam found its use in providing a secure fixation of installed window frames and door formwork, as well as filling voids. It is characterized by the following properties:

• Significant amount of covered area. When leaving the cylinder, the foam expands its volume, the difference of which in relation to the initial one is 40 times.
• Good adhesion. The foam adheres strongly to most materials, except for oily and polymeric coatings.
• The ability to fill all hard-to-reach places.
• Ensuring a good degree of sound and heat insulation.

You need to know that foam, despite its simplicity, requires special attention when working with it:

• foam should be handled at temperatures above +5°C,
• any work must be carried out with gloves to exclude the possibility of foam getting on unprotected areas of the body,
• before starting work, shake the container thoroughly for a minute so that the contents acquire a homogeneous structure,
• the cylinder during the entire operation should be kept upside down, that is, with the cap down, so that the gas that displaces the mixture from the cylinder can freely exit, since it is lighter than other components,
• any product must be covered protective layer paint, since the mounting foam is afraid of direct exposure to ultraviolet rays.
• complete hardening of the surface occurs after 8 hours; before the specified period, the material should not be subjected to loads.

Thanks to unique properties foam, many crafts made from this versatile sealant began to appear.

What tools will you need to create crafts from polyurethane foam

To get started, you need a simple set: the mounting foam itself in cylinders and a special gun for it, the cost of which starts from $ 5. In addition, the work will require the following tools in order to create garden crafts:

• stationery knife,
• artistic brushes different sizes: 4.8, 10 and 25 mm wide brush for decorative work,
• foam cleaner,
• Oil paint,
• weighting agents. Since the foam has a low weight, only 20 kg per m³, products should be equipped with simple loads, the role of which is played by a container with sand - a plastic bottle or a small can,
• colorless protective varnish. Simple varnishes are not always suitable due to the fact that the resulting products will become yellow,
• several pairs of household gloves: cotton or rubber. The latter are preferable, since household gloves sometimes provide insufficient protection for hands. It is important to remember that the foam is difficult to remove if it comes into contact with the skin, so the use of gloves is mandatory.

When these tools are prepared and the necessary stock of foam is available, work should begin.

Where does the work on the manufacture of crafts from polyurethane foam begin?

Since it’s hard to keep an artistic image of a craft in your head, you should first have photographs or pictures that reflect the essence of the future product and its prototype. Next, you need to build a frame with a weighting agent, on which mounting foam will be applied in layers. For the construction of the frame, plastic containers are most often used, which are filled with sand to provide weight. In addition, there is another method that is structurally more efficient, when the frame for the future product is either welded from thin reinforcement with a diameter of 5 mm, or twisted from thick wire. To ensure the stability of the craft, if it is located on the ground, you should leave the steel parts protruding 20 cm outside. For example, if a deer figurine is created in a standing position, the rods should be passed from the hooves.

In this way, better stability of the figurine against the wind will be achieved, as well as a more evenly distributed load on all parts of the product.

In the event that work on creating garden foam crafts is carried out indoors, a respirator should be used. The mounting foam itself is not toxic, but has an unpleasant odor.

The process of creating crafts for the garden, according to novice sculptors, is not difficult. It is only necessary to act carefully and allow the foam layer to harden in time before proceeding with the application of the next layer.

Creating figures for the garden from polyurethane foam

The process of creating a figurine is technically simple. You need to follow the steps:

• Creation of the frame of the figurine. If the craft is squat, then it is enough to use a plastic container with sand as a base, which, using improvised materials, should be adjusted to the required dimensions of the form.
• Next, foam is applied using a mounting gun. The use of this tool will allow you to accurately dose the amount of material.
• Allow 20 minutes for each layer to dry.
• With the help of a brush and a clerical knife, when the foam layer is hardened, the crafts should be given the necessary size and shape.
• After all the layers of foam have been applied, and the figure has acquired a finished look, it is worth puttingtying the entire base so that there are no cracks.
• After that, the product is painted with acrylic paints, applying at least two layers to the figure.
• At the end of the work, the figurine is varnished to ensure better preservation and resistance to weather conditions.

The finished craft should be left for several days so that all materials acquire the final degree of hardening.

Foam lamps and lanterns

A real master class can be shown by those specialists who create not only beautiful, but also functional things from polyurethane foam. Working lights on the site will be a beautiful and eye-catching addition to the overall picture. And what is nice, making them is not much more difficult than a simple figure.

To create a lamp, a base is made in the form of a stool from chipboard or OSB, since the latter is more durable. Then the following actions are performed:

• the base is carefully foamed with a mounting gun,
• further complemented by others wooden elements, which are also treated with foam,
• in the upper part of the wooden structure, it is necessary to make a cover for inserting a lantern,
• thereafter top part covered with a layer of foam and additional decorative elements(wooden lintels, forged fittings),
• final stage - painting finished construction, after which the lamp is placed through the cover on the body.

If the flashlight is powered by solar battery, then you should fix it on the side. But this will break the aesthetic appearance, so you should consider installing a flashlight that runs on batteries.

Ready workers lighting covered with several layers of foam, followed by decoration. In this case, if the lamp has a supply power cable- an aesthetically pleasing design. Even if the lamp is old-style and does not differ in sophistication of style, such a procedure will breathe new life into an old thing.

Decorating dishes with polyurethane foam

In the event that the initial skills are not enough to carry out such work, it makes sense to practice on the dishes. Decorating is not difficult, just a few steps:

• clean the surface of the selected object from contamination,
• apply a layer of foam using a mounting gun,
• at the time of its polymerization, use a brush and a knife to correct the resulting mass to give it a more regular shape,
• after hardening, cover the surface with a layer of paint.

As you can see, the process of decorating dishes does not have significant differences compared to the creation of a figurine. The presence of the selected dishes as an element of the base will allow you to conduct experiments without being distracted by the construction of the frame. A similar method is used for any vases, cabinets or baskets.

Creation of panels and ornaments from polyurethane foam

Mounting foam is also suitable for creating entire decorative panels. For example, a simple steel grating will gain the new kind thanks to the application of foam on each of the rods, followed by the creation of artistic elements that imitate forging. With the help of the form, it is quite possible to create simple decorative cladding panels, the purpose of which will be to give the building or its individual elements greater external appeal. In general, the possibility of using polyurethane foam is limited only by imagination.

It is not difficult to create crafts for the garden with your own hands. The foam itself is light and easy to use material, which, in addition to many advantages, also attracts with the price. The cost of a balloon of polyurethane foam with a volume of 850 ml starts from $ 3, which allows you to special costs create entire artistic compositions. To ready product pleased with its appearance, you should use a few practical tips in your work:

• after the foam layers have hardened, the finished product should be allowed to “rest” for 3-4 days to achieve maximum strength,
• for the safety and integrity of the coating, after applying several layers of paint, it is advisable to apply varnish to the coating. It is recommended to use a colorless protective lacquer, because, unlike the usual one, it will not impart a yellowish tint to the painted products,
• before painting, make sure that the selected paint does not contain a nitrocellulose base. Otherwise, the foam structure will be softened,
• the clerical knife used should have a good blade sharpness in order to effortlessly cut the foam. Otherwise, the blade will tear the viscous base, which will violate appearance crafts,
• cheap polyurethane foam does not hold its shape well, so when working, you should refrain from buying inexpensive bottles up to $ 3, the optimal choice would be foam from the manufacturer Tytan, at a price of $ 5.5 for a bottle of 850 ml,
• simple crafts of small sizes do not require the creation of a frame.

As can be seen from what has been written, learning to create beautiful compositions if you have an understanding of the final image, it is not difficult, although it will take time. If you want to use only professional polyurethane foam to create high-quality crafts, then you should trust the choice of specialists.

According to bench tests, Tytan Professional 65 O2 polyurethane foam is the leader among the proposed mixtures:

• film formation time takes 4 minutes,
• initial hardening of the material occurs after 25 minutes,
• the volume of material during the initial expansion was 51 liters, which is twice as high as most of the tested competitors,
• mixture output mass - 900 g.
• retail price from $ 5.5 per cylinder, which, together with big amount foam at the outlet can significantly reduce the cost of buying new cylinders.

This foam is well suited not only for masters, but also for beginners. Blowing occurs slowly, which gives time for processing the layer to give the desired shape. Budget foam M70 from the manufacturer Hercul will also become good choice, since it has average performance and a low price of $ 3, at the same time, it significantly outperforms the leader in terms of hygroscopic properties.

Mounting foam, crafts for the garden from which you do not need to make - is:

• Makroflex
• Houser
• Expert
• storehouse
• Ultima
• Bau Master
• Baumax
• Cyclone

All of these manufacturers sell low quality foam, which begins to lose its shape after 5-6 months.

To decorate your household plot, you do not need to complete art courses and have "golden hands". A small set of tools, a little diligence and abstract thinking will allow you to get gnomes, frogs, sheep and Christmas trees from quite affordable material.

Manufacturing technology

First things first, stock up necessary materials and tools. This will determine how well and quickly the manufacturing process will go:

• Plastic bottles are suitable for the frame of the product filled with sand, boards, metal objects and thick wire. Even an ordinary brick can become the basis for a future mushroom on its site!
• Mounting foam.
• Foam gun.
• Gun cleaner.
• If you plan to grow flowers in sculpture, then in the center of it you need to mount some kind of container such as a bucket, tin can or the same plastic bottle.
• Varnish, paint and brushes for them.
• Stationery or other knife.
• Several pairs of gloves. This item is required, as mounting foam quickly and permanently sticks to your hands!

In the photo foam mushrooms:

The very process of creating garden figures consists of two successive processes. First, we apply foam to the base and let it harden a little. Then we apply again and so on until we approach the shape we need.

After that, extra protrusions are removed with an ordinary clerical knife, the sculpture takes on a finished shape and can be covered with paint. The whole work can take from an hour to several days, depending on the size of the figure and the thickness of the applied layer. All this is desirable to do in a separate dry room, where there is no excess dust and children do not run. Otherwise, you will have to wash with gasoline or acetone an extremely sticky substance, which is polyurethane foam.

This video shows how crafts are made from polyurethane foam:

Manufacturing examples with instructions

Below are a few examples of different figures that even a beginner can create on his site. The main thing is to strictly follow the sequence of all operations. And in a few hours you will definitely feel like a real creator, from whose hands an excellent decoration for a summer cottage comes out!

Christmas tree

Making a Christmas tree out of polyurethane foam is as easy as shelling pears. To do this, you need to collect twigs and attach them to iron pipe. This can be done with tape or wire.

After that, it is necessary to wet the workpiece from the spray gun so that the foam “sticks” to the base more firmly.

Acrylic green paint is great for creating a Christmas mood with simple things like stick trims, twigs, polyurethane foam and fishing line.

Ball

The ball is the easiest figure to make. It is recommended to start your creative experiments with it, and after that move on to more complex decorations and sculptures.

1. We take a can of paint and fill it with sand;
2. Layer by layer we apply mounting foam;
3. Upon reaching required size and more or less spherical shape, we remove the extra parts with a knife;
4. We cover the product with varnish;
5. We choose the paint for our decoration, depending on our preferences;
6. If this is a bun or the head of some animal, we make eyes, a nose and a mustache from buttons, fishing line and wire.

Ram and sheep

1. First, let's make a frame. We take several plastic bottles and fasten them with tape. It will turn out something like the "skeleton" of the animal. The lower "limbs" can be filled with sand to make the figure more stable.
2. Next, you can already apply foam. But to save it, it is better to wrap the frame with isolon or other polymeric material. The first layer of polyurethane foam - you already have a rough idea of ​​​​what will happen in the end!
3. We make ears from pieces of skin. You can also make them from plastic bottles by preheating and bending them.
4. We process the muzzle with a knife, carefully giving it the necessary features.
5. We cover the product with varnish.
6. With paint we draw eyes, a mouth and other "features" of our sheep or lamb!

Goat

1. We make a frame of thick wire, with which we wrap several plastic bottles.
2. As a frame for the legs (bones), it is better to take metal pipes. They can be welded to a pedestal, dug into the ground, or secured with bolts. Your figurine must endure wind and rain, so be sure to securely fasten the base.
3. We apply one or two layers of mounting foam.
4. We make horns and a tail from wooden sticks or plastic cuts and fix them.
5. After applying the last layer, cut off all unnecessary and wrap the product with a sickle or fishing line.
6. We cover the surface with a primer and paint. You can choose any color, because it is completely your creation!
7. We make eyes from buttons.
8. We place our goat next to a pond, in a clearing, in the company of other decorations, etc.

In total, the production of this sculpture will take from one to two weeks, since each layer of foam must harden. As a result from unnecessary pipes, plastic bottles, wire scraps, other "garbage" and several cylinders of polyurethane foam, you get an excellent decoration for your summer cottage!

New Year crafts

Even with nothing at hand but a wire and a can of mounting foam, you can create excellent New Year's decorations. various ornaments, Christmas decorations, simple and complex figures - all this is accessible and simple!

For example, you can make a snowflake. We take a wire of such thickness that it can be bent without effort. We make the frame of the future snowflake out of it. Gently apply one or two layers of foam. While it has not hardened, we achieve even and smooth surfaces. If something goes wrong, you can always add a little foam and cut off the protrusions with a regular clerical knife.

Christmas ball made even easier. The tennis ball is covered with a layer of foam. After hardening, we apply a layer of paint and decorate our New Year's toy in bright and positive colors!

A simplified version of the Christmas tree is done using cardboard or isolon, wound on a rigid base in the form of a cone. Even a child can apply several layers! We level the surface, paint and put it in a prominent place.

Basic rules for working with mounting foam

• Shake the bottle periodically.
• The ideal temperature for work is room temperature.
• Mounting foam does not like direct sunlight. Therefore, it is necessary to work in the shade, and cover the finished product with paint.
• The setting time of the foam will vary depending on the manufacturer, temperature and speed of operation.

Important Points

• The paint used to cover the finished product must not contain nitrocellulose. Otherwise, the mounting foam will soften and the decoration will lose its shape.
• Gloves are required element work. Without them, washing hands will take much more time than the process of making crafts.
• Mounting foam is a very light material. Therefore, heavy objects must be placed inside any product made from it. It can be a jar of sand, a plastic bottle filled with water, an iron base, metal pipes fastened with wire, and other massive things.

garden figures it is quite easy to make it with your own hands from polyurethane foam, for this you will need a minimum of improvised materials. Armed with a can of polyurethane foam, you can make almost any figure that will become a real decoration of your garden.

Using a plastic bottle and polyurethane foam, you can independently make an original garden figure.

How to make a stork from polyurethane foam?

You will need:

• plastic eggplant from under the water;
• thick wire;
• Styrofoam;
• stationery tape;
• mounting foam;
• wood chip;
• electrodes (for bird legs);
• sharp knife;
• poultry feathers;
• paint and varnish for facade works.

A stork made of polyurethane foam with your own hands will be the highlight of your garden. The first step is to build a frame, which will subsequently be covered with foam. The basis of the frame is a plastic eggplant from under the water for 5 liters. From the side of the bottom is placed the head of a bird, the neck serves as a tail.

The stork's neck is made of thick wire: a small piece of foam plastic is applied to the bottle, it is pierced with a wire at an angle so that the wire rests against the wall of the eggplant. To make a bird's head, take a small piece of rounded foam, put it on the end of the wire. The nose is made from a piece of wood or a small piece of wire.

The legs of a bird are made from electrodes that are out of order, and metal fittings can also be used for this. At the junction of the legs with the body, pieces of foam are placed, since the stork's legs have a thickening at the top. The stork will be inserted into the ground with electrodes, so the figure does not need additional weighting, but if desired, you can fill the eggplant with sand.

For the wings, flat pieces of polystyrene in the form of a semicircle are suitable - they are attached with wire to the sides of the eggplant. In order to give the frame the necessary strength, it is wrapped with tape. Work begins with the head, gradually moving to the base of the legs of the bird. It is not necessary to wrap the electrodes with adhesive tape.

PVA glue is used to prime the figure.

After all the parts are fastened, proceed to shaping with foam. The foam is squeezed out in small zigzags or stripes, and there is no need to try to accurately repeat the contours of the bird, since everything superfluous will then be cut off. Important: the foam is laid thin layers with obligatory intermediate drying. This building material dries quickly enough, so the next layer can be applied after 15-30 minutes.

After the foam hardens, they begin to form a sculpture: with the help of a sharp knife, they cut off everything superfluous. It remains only to paint the stork. In order to reduce paint consumption, it is necessary to apply a primer that forms protective film and will not allow the porous foam to absorb the paint. As a primer, you can use PVA glue diluted with water in a ratio of 1: 2. The neck and body of the bird are painted in White color, the tips of the wings and the tail are black, the nose and legs are covered with red paint. The result is fixed with any facade varnish. At the end of the work, a bunch of real goose, duck or rooster feathers is inserted into the tail hole (bottle neck). The figurine of a stork is placed on a flower bed, deepening the electrodes (legs) into the ground.

How to make a donkey out of polyurethane foam?

You will need:

• eggplant from under the water for 10 l;
• can;
• wire;
• sharp knife;
• mounting foam;
• glue gun or double-sided tape;
• wooden boards (for legs);
• facade putty;
• primer;
• facade paint and varnish.

Foam figures can be small or large, it all depends on your imagination and the materials available. To make a donkey, you need a plastic eggplant from under the water for 10 liters. A tin can is perfect for the head, and if there is none on the farm, then you can use a cropped 5-liter eggplant. The legs of the donkey are made of wooden planks, the tail is made of wire or glazing bead. The head and legs are glued with glue gun or double sided tape, the tail is inserted at a slight angle into a hole made in advance.

In order to make the figure heavier, it is necessary to fill the eggplant with dry sand - it is better to do this after the glue has dried.

In the manufacture of garden figures, a special gun for polyurethane foam is used.

Layers of polyurethane foam are applied to the prepared frame. It is necessary to allow the previous layer to dry for 15-20 minutes, only after that the next layer of foam is applied.

Donkey ears are made of wire, which is bent in the form of a semicircle. Then the wire frame is wrapped with tape or paper, inserted into the donkey's head, and then foam is applied to the ears. Next, the foam is cut with a knife in such a way as to give the figure the desired shape.

In order for the sculpture to look believable, it is necessary to apply facade putty on top of the mounting foam, having previously primed the product. The primer improves the adhesion of materials, so this process should not be ignored. Small details are worked out on raw putty: nostrils are cut out, animal eyes are made. After drying, the putty is passed over the surface sandpaper with fine grain. The donkey figurine is painted with acrylic facade paint, and then covered with waterproof varnish.

Foam mushrooms

You will need:

• plastic bottle;
• Styrofoam;
• wire;
• stationery knife;
• primer;
• facade putty;
• acrylic facade paint and varnish.

Even a child can make mushrooms from polyurethane foam, for this you do not need to have the talent of a sculptor or artist. To make a mushroom leg, you will need a plastic bottle. To give the figurine stability, the bottle is filled with pebbles or dry sand. Foam is applied to the bottle in such a way that a thickening characteristic of the fungus is obtained at the bottom. The foam is distributed in thin layers with intermediate drying.

To make a mushroom cap, they take foam plastic, cut a circle out of it, and you don’t need to try to repeat the exact shape, since in nature there are no mushrooms with perfectly round hats. Foam is applied to the foam in such a way that a cone is gradually formed. A strong wire is inserted into the leg of the mushroom, a cap is put on it, the junction of the parts can be smeared with glue. Next, apply the last layer of foam, let it harden, and then cut off all the excess.

Polyurethane foam is a porous material that easily absorbs moisture, so the product must be primed. If this is not done, then the moisture from the putty will turn into foam, which will finishing material drier, and this may subsequently lead to cracking of the surface. If the farm does not have a primer, then it can be replaced with gelatin. Gelatin is soaked in cold water(15 g per 100 ml), let it swell, and then melt it in a water bath. Melted gelatin diluted warm water. The figure is treated with this solution 2-3 times with intermediate drying.

Next, facade putty is applied to the fungus (can be replaced with plaster) and left to dry completely. The surface is first sanded with medium-grain sandpaper, then fine-grained paper is used. The product is primed again - if this is not done, then the paint consumption will double. The mushroom cap is dyed Brown color, for the legs use white with the addition of ocher. The work is covered with facade or yacht varnish in 2-3 layers.

Garden figures made of polyurethane foam will bring an atmosphere of comfort, make the estate individual and unique. Everyone can make a fungus, a stork or a donkey, if you show a little imagination and acquire the necessary materials.

Making garden figures with your own hands from polyurethane foam is a great solution for any good owner. Even the smallest garden plot, not to mention the creations of landscape designers near expensive cottages, will be decorated with garden figurines - fairy tale characters, funny little animals, cartoon characters. It is not so important what material they will be made of and how much they will cost if these characters turn a piece of your garden into a fabulous space for the delight of children and guests.

Having decided to decorate your site garden figurines First of all, you need to decide how you see them. You can make future garden residents from the most different materials but not all of them you can handle on your own. For example, wood carving, and even more so stone carving, requires considerable professionalism, so it is better to order such garden figures from specialists or buy ready-made ones. The same applies to the manufacture of plaster sculptures. It is clear that this will require additional costs, including the delivery of figurines to a new place of residence. In addition, each of the mentioned materials has its drawbacks.

Garden figurines made of wood look great - they are beautiful, "warm", environmentally friendly. pure material. However, in natural conditions among grass and bushes, such crafts for the garden may be short-lived or require special protection from dampness and rot.

Stone sculptures fit perfectly into garden reality and last for a long time, however, stone is heavy material both literally and figuratively, so the figures will be inactive, and not suitable for every style.

Gypsum crafts for the garden are perhaps the most widespread today due to their relative cheapness and ease of manufacture. However, if the manufacturing technology is not fully observed, they may turn out to be fragile and not water resistant enough.

Figures made of polyurethane foam are not only devoid of the listed disadvantages, but also have additional advantages:

• low weight - so much so that during manufacture it is even recommended to fill the frame elements with sand or pebbles so that the characters made from polyurethane foam with their own hands are sufficiently stable;
• almost unlimited freedom when working with the material - foam allows you to easily and quickly add in one place and subtract in another, because it is perfectly cut and can be applied to any surface, which is, of course, very convenient for a novice sculptor;
• unlimited shapes, sizes and style features because foam can be used to create a cartoon snail on the lawn, and a Japanese-style lantern;
• insensitivity to moisture, temperature changes and other natural phenomena.

In other words, polyurethane foam as a material allows you to make a garden figure of any shape and any size.

Preparation for work

It is relatively easy to create a sculpture for a garden from polyurethane foam on your own, but you need to think everything through in advance.

First, you need to decide what kind of characters will become the inhabitants of your garden or vegetable garden. It is very important that they organically fit into the style of the site. Indeed, some monumental girl with an oar will look strange in a small dacha, and in Japanese garden- the frog princess or kolobok from Russian fairy tales. In addition, it should be borne in mind that there should not be too many such art objects, they should be a pleasant surprise for visitors, and not be found at every turn. If in doubt whether a do-it-yourself figure made from polyurethane foam will look good in one place or another, you can draw on cardboard and cut out its approximate layout. Put it in the intended place of residence of the future character and figure out how everything will look in reality.

Secondly, prepare in advance not only a balloon with foam, but also what you are going to make a frame from for a future sculpture. These can be metal buckets and cans, plastic bottles, boards and bars, fittings, strong but well-bent wire, thick cardboard, plastic tubes, etc. In fact, anything can become the basis for a future masterpiece - the foam coating will hide everything. The containers intended for the frame must be filled with sand or small pebbles to give stability to the finished figure. And the wire, from which it is convenient to make arms, legs, tails, is better to hide inside the hollow plastic tube so that the area to be covered with foam is larger and internal damage is less.

Thirdly, before you start sculpting figures from mounting foam with your own hands, carefully study the instructions for the foam that you purchased, since each manufacturer has its own nuances and requirements. Don't forget to stock up on individual protective equipment to work with this building material - at least with gloves and a respirator.

Step by step instructions for creating sculptures

So, are you ready to become a "foamy" Michelangelo? Then get started.

1. 1 On the made frame or part of it (in some cases it is better to connect the parts of the figure in almost ready-made) apply mounting foam in layers. The key here is to take your time and be patient. The foam is applied in thin layers, which must be allowed to dry for 15-20 minutes, otherwise pieces will begin to fall off your product. The bottle should be kept cap down to be able to use all the foam, without residue, and it is best to use a special gun to apply it. It is not recommended to work with this material when sub-zero temperature otherwise the result may disappoint you.
2. 2 Fully polyurethane foam hardens in about 11-12 hours, so at the stage of layering you can form it by hand, sculpting desired forms. When the material hardens completely, you can, following the example of the great sculptor, cut off the excess with a clerical knife. In this case, you can not only cut, but also add to right places material - in this sense, polyurethane foam is unrivaled.
3. 3 The finished and dried sculpture, so that it does not collapse in the future and serves as long as possible, should be covered with a layer of putty. To create a flat and smooth surface, the product is rubbed with sandpaper.
4. 4 Paint the sculpture better acrylic paints, and there should be at least 2 layers, otherwise it will not come out very beautifully. Simultaneously with the coloring, all the small details are installed, including the eyes, which can be made from beads (by gluing them on the face or muzzle) or from small rubber balls - this way the look will be more expressive. So that your work does not lose its beauty for as long as possible, after painting it is recommended to cover it with a layer of varnish.
5. 5 That's it, your masterpiece is ready, you can install it in its place. However, due to the lightness of the statue, you can change this place over time.

I would like to note that making figures for the garden with your own hands is especially nice if you do it with your children. In this case, your offspring will be able not only to enjoy meeting the funny inhabitants of your site, but also be proud that they participated in their creation.

Crafts from polyurethane foam can be made with your own hands in just a few hours.

If you have a disposable tank that hasn't run out yet, why not put it to good use. landscape design.

In this case, it is still better to resort to professional foam, and not household foam, since a small gun with a diameter of 2 mm is added to it.

Extraordinarily simple and beautiful figurines from mounting foam will become the property of your site. They will not leave indifferent either neighbors or just people passing by.

Materials for fakes from polyurethane foam

You will need:

• gloves;
• sprayer with pre-prepared water;
• polyethylene;
• aviation kerosene.

Kerosene is needed so that, upon completion of work with mounting foam, hands can be easily washed from building material.

Something will also come in handy for creating the basis for crafts from polyurethane foam with your own hands.

You can take the usual plastic bottle, an old pan or something else, which is not a pity.

With foam coating auxiliary material creating crafts and begin ...

You need to paint them carefully, and before carrying out this procedure
dry thoroughly in the shade. Drying takes at least a week, but if the foam layer is large, it is better to wait longer.

The paint is applied to the craft from mounting foam with your own hands every spring again. If this is not done, the foam may crack and the craft will deteriorate.

Foam craft ideas

If your site has a small pond, you can make a large green toad. This is especially true where many plants grow, especially large-leaved ones. In some cases, it is easier to make a lizard or a crocodile - who can do what.

In order not to miscalculate with the sizes and “fill your hand”, you can practice on plasticine. No matter how strange it may sound, but it was after trials on this simple material, it turns out to make chic crafts from polyurethane foam.

The same goes for dough - if you like to bake delicious buns, pat the animals - this will help you figure out what you can do better.

Perfect solution- make turtles from polyurethane foam. And it is not at all necessary to have a reservoir on the site. In addition, almost everyone has white paint, and it is now cheaper than colored ones.

Turtles are easier to dye, their shells can be alternated with natural ones. If, during the creation of the craft, bumps appeared that should not be, they can be cut off with a sharp knife.

Similarly, the situation will be with rounded details - if they need to be sharpened, the excess is simply cut off.

Crafts from polyurethane foam not only street views decorate, they can be made for the home. Funny frogs will bring smiles to people passing by!

Yes, as original New Year's decor you can make a snowman out of foam, but you need to start creating in advance so that the material has time to dry well.

If you paint over the foam ahead of time, it will quickly crack.