Floors from the end saw cuts of wood. Do-it-yourself wood cut floor photo

What is not made from wood cuts. Garden paths, shelves, countertops, interior decoration and much more. Using saw cuts instead of floors in a living room is what our author decided to do.

Materials and tools
dry logs of different diameters;
a circular saw;
grinding machine;
liquid Nails:
grout for tiles;
polyurethane varnish for wood;

From dry logs of different diameters on circular saw Sawed kruglyashi approximately the same thickness.

Using a grinder, he polishes each saw cut.

Prepared the base of the floor by removing the old coating. Under the bottom was a concrete screed, which made it easier for the author to carry out further work.
Then he lays the saw cuts as close as possible to each other.

The empty space is filled with smaller cuts, twigs.

By laying out the entire area with liquid nails secures each saw to the floor.

Waiting for the glue to dry grinder smoothes and polishes the floor. The floor must be level and smooth.

Grout for tiles wipes the gaps between the cuts.

After waiting for the grout to dry completely, I covered the floor with polyurethane varnish for wood. The varnish was applied so that it would get into all the cracks. Polyurethane varnish is applied in 3-4 layers. After the varnish has dried, the floor from the saw cuts of the tree is completely ready.

Natural materials are appropriate in different styles landscape design, therefore, among the variety of all kinds of country paths, wood flooring is often found. If you decide to make a path from boards in the garden, a wooden floor on the terrace or a path from tree cuts with your own hands in the country, look at the photo options, study all the stages of preparing the site and wood, how to lay wood and how to care for the coating.

Where to get saw cuts from wood

Comfortable and beautiful walk on the lawn

What are the advantages of wood materials

The attractiveness of wood materials for the construction of country "means of communication" is determined by:

Availability. Of course, wood prices are rising, but the cost of wooden paths remains lower than that of stone, clinker, paving slabs. In addition, you can use lumber and fallen trees on the site that were not used in the construction of buildings in the country.
High decorative. The unique texture is beautiful in itself, allows you to create pleasing to the eye unique coating with original design.
Ease of operation. The construction of wooden paths does not imply the presence of a special theoretical training and specific practical skills. It is enough to be able to use a saw, a shovel, a hammer.
Environmental friendliness. Natural material is safe for health, harmonizes perfectly with environment, especially popular among fans of eco-style.

Natural decorativeness of wood - each cut has a unique pattern

Disadvantages are also present: wooden paths are not very durable, they are prone to insects, fungus, and mold. And yet they can be used from 7 years to a quarter of a century, depending on the type of wood. However, this requires: competent processing of blanks before laying, correct installation and a reliable foundation, arranged according to all the rules.

The tree is in perfect harmony with the environment

Preparation of the base for the main path

So that the garden path does not swell, fail, overgrow with weeds and eventually crumble in the next year or two, you need to prepare a reliable bed (base) for it.

Marking the contours of the path

This is a simple, but rather laborious task is as follows:

On the territory, mark the boundaries of the track with a cord stretched between the driven pegs. On the bends of the route, pegs should be placed often, with an interval of no more than half a meter (depending on the radius of curvature), and on straight sections, pegs can be driven in after 2 or even 3 m. You can also mark the contour of a winding path with sand, chalk powder, lime.

If you plan to install curbs, provide for an appropriate indent when marking the width of the bed.

Within the markings, select the soil by about 20 cm, controlling the depth of the resulting trench with a template or ruler. This should be done in dry weather: rain that has spilled into the trench will significantly reduce the quality of the foundation.

If curbs are needed, install them by leveling them. Under the curbs, it is desirable to add compacted sand.

Tamp the bed, line it with geotextile or PET film to protect against weed germination and prevent subsidence.

Lay a drainage layer of gravel or crushed stone of a fine fraction 4-10 cm high on the bottom (depending on the stability of the soil). You can use a gravel-sand mixture (9:1). Thoroughly tamp with a roller, vibrating plate or hand-made homemade rammer.

For some types of paths, it is required to pour a sand cushion of the same height over the drainage layer. It must be poured gradually, in layers, moisturizing and well tamping each layer.

Start of foundation preparation work

After that, you can start laying paths made of wood of one design or another in the garden.

How to lay out a path from wooden cuts

The advantages of using wooden saw cuts (cuts, slices, logs) as a material for paving paths have already been appreciated by many summer residents and homeowners. The paths, paved with charming logs, allow you to comfortably move around the site, look organically among green spaces, perfectly set off blooming flower beds.

A path made of wooden saw cuts emphasizes the beauty of greenery and flowers

Where to get saw cuts from wood

Ready saw cuts from various types of wood are offered by many manufacturers. You can even buy already processed special formulations blanks that will only need to be properly mounted on the prepared base. This option is good when the budget allows.

However, if you even glance at the price lists, you can experience some disappointment. For example, untreated larch sections with a diameter of 30 cm and a height of 10 cm domestic manufacturer are offered at 150 rubles / piece.

A simple calculation shows: material for a 9-meter trail 60 cm wide will cost 9,000 rubles. excluding shipping and handling charges before packing. And if you make cuts of a tree for a path with your own hands from a fallen trunk that clutters up the site, the same path can be paved almost for nothing.

You can prepare saw cuts yourself

How to make cuts with your own hands

Cheaper than ready-made cuts will also cost blanks sawn independently from purchased round timber. You will need a few tools for work:

benzo or electric saw;
tape measure or template;
pencil or crayon for marking;
sanding scraper.

Any type of wood can serve as the starting material. However, if there is a choice, then conifers it is better to take larch, pine, and from deciduous - oak, alder, hornbeam, acacia. The paths made of larch and oak will last the longest. But you need to keep in mind that the wood of these species is difficult to process. The selected tree must be dry, otherwise the cuts laid in the ground will warp, crack - the work will go down the drain.

To make saw cuts, you need to perform the following manipulations:

Clear the trunk of branches.

Sand the barrel with a scraper or other tool. Perhaps someone will prefer to peel ready-made logs from the bark.

Using a template, mark the log lengthwise into equal parts of 10-20 cm. The thicker the trunk, the greater the saw cut height. In order for the cuts to be securely held in the track, it is undesirable to make them less than 10 cm high.

Dissolve the trunk according to the marks.

Wood cuts are ready

Treatment of slices with special compounds

Before proceeding directly to laying the path from the saw cuts of the tree with your own hands, the cut blanks must be processed to protect against insects and fungus. For this purpose, you can use:

special antiseptics, impregnations deep penetration purchased at the store, using them according to the instructions;
home remedy solution blue vitriol(10-20%), in which the cuts must be kept for two days, then dried for the same time in the shade;
drying oil brought almost to a boil - it must be applied with a brush on all surfaces of the cuts;
working off engine oil - use it as drying oil.

Path from "aged" wooden saw cuts

From the impact of copper sulphate, the tree quickly darkens. If there is a desire to achieve the effect of an "aged" tree, such processing is what you need. In an effort to preserve the natural color of the material, it is more advisable to impregnate with drying oil. You can also use the old trick of the inhabitants of taiga settlements - soak saw cuts with a saturated decoction of larch bark. It will give the wood antiseptic properties and a pleasant red-brown color.

These cuts are ready to be laid

After the logs have dried, it is necessary to apply a waterproofing layer on their lower part. To do this, the bitumen must be melted in a metal bowl and the bottom of the workpieces should be dipped into it. This operation is not safe: bitumen is not easy to boil, and the temperature of the molten substance exceeds 200°C. You can use other ways to create a waterproofing layer:

Briquettes of bitumen, placed in a metal container, pour gasoline, leave for several days until a liquefied bitumen mass is formed. Process saw cuts in it, as in hot bitumen.

Cover the lower surfaces of the logs with Kuzbasslak.

Laying prepared logs on the base

Paving a path from trunk cuts

Now, there is very little left until the moment when you can be proud of the wooden path made by your own hands in the country. The most exciting creative work for the installation of saw cuts.

Scheme of the device of the trail from saw cuts

To fully realize your idea, you must do the following:

While the finished saw cuts dry out after impregnation, prepare a bed for them using the technology described above. Provide such a thickness of the compacted gravel-sand "pie" so that the upper ends of the logs are flush with surrounding soil or slightly above it. If borders are planned, their role will be successfully played by higher saw cuts, wooden chopping blocks.

Make sure the bed is level using a level.

Start paving. Set each element in its place, pressing into the sand and leveling by carefully tapping with a wooden or rubber mallet. Control by level so that all slices are in the same plane.

Lay out logs according to any chosen scheme: from a single-row path from saw cuts large diameter to the path, densely paved with saw cuts of different diameters and configurations. It all depends on the artist's intention and the availability of blanks.

Fill the gaps between saw cuts with sand, crushed stone sifting, small pebbles with earth. Decorate such a wooden path sown in the intervals between saw cuts ground cover plants or moss.

Finish Edges: Decorate decorative stone, cover with crushed stone, gravel or just soil and tamp well.

You can get ideas for decorating paths from wooden cuts by looking at the photo below.

Caring for a wooden path

To use the saw cut path long time, she will have to take care of:

Annually clean off the dirt with a metal scraper, then treat with an antiseptic, drying oil or (if desired) cover with paints and varnishes for outdoor use.

Timely remove weeds that can disrupt the base of the coating.

Avoid flooding and erosion of the coating. For this purpose, you can install special grooves on the sides of the path or arrange grooves.

In winter, sweep away snow in a timely manner, to prevent the formation of ice on the surface. At the same time, it is worth refusing to use salt or other reagents for cleaning ice, which contribute to the gradual destruction of wood.

It is prestigious to have such a floor

Floors from wooden saw cuts - it's stylish

Having a supply of material for cuts and acquiring some skills in working with them, you can make an unusual floor from wood cuts - this is now fashionable. Depending on what will serve as the base of the floor, can be applied various ways styling and finishing floor covering.

Floor made of sliced wood on a soil basis

If you need a floor on a soil basis (say, for an open terrace), you can build it exactly according to the same scenario as a saw cut path. But there are also differences:

Paving should be made as dense as possible, using saw cuts of different diameters.
The remaining gaps between saw cuts do not need to be filled. bulk materials- the prepared mastic should be pressed into them (about it a little lower), leveling the surface with a rubber spatula.
After the mastic has dried and the surface has hardened, it is required to walk on it with a sanding machine. Then carefully remove the dust and polish the floor with linseed oil and wax or apply parquet polish.

Mastic preparation:

Soak 2 kg of clay.

Thoroughly mix it with 1 kg of slaked lime.

Add 1 kg of technical fat and 4 kg of small sawdust.

Mix until a homogeneous mass is obtained.

Laying saw cuts on a solid base

"Eternal" floor made of wooden saw cuts

Noteworthy is the option of an expensive, but truly durable floor, mounted on a solid base. At the same time, the height of saw cuts laid on concrete screed or an old wooden floor, can be substantially reduced. For this floor you need:

Level and clean the base.

Apply a polyurethane self-leveling floor to a small area of the base. Lay wooden slices as tightly as possible in this area. By the way, the sections made from the remnants of the timber will provide the highest packing density.

Go to the next section, repeat the previous operation.

After gluing the saw cuts over the entire base, wait for the polyurethane to harden and seal the joints with a mixture of polymer and sawdust.

Treat the dried floor with a grinder. Remove dust after sanding.

Pour top coat from polyurethane.

"Parquet" from the end saw cuts of timber

Lumber trails - simple and inexpensive

If the process of harvesting and laying saw cuts seems too complicated and lengthy, you can quickly and easily build a variety of wood paths for the garden using ready-made lumber: boards, timber different size. The most straightforward option is panel flooring, which does not require time-consuming preparation of the base.

wooden garden path

For such a path, planed edged boards the same thickness (preferably and equal width), wooden blocks, hacksaw, hammer, nails. Flooring manufacturing process:

Mark the path, level the ground along the route of the path (fill in the holes, tamp, cut off the tubercles).

Saw the timber into segments with a length equal to the width of the path. Trim the boards.

Soak the boards and bars with an antiseptic, dry.

Treat the bottom of the boards and each surface of the bars with bituminous coating (or cover with Kuzbasslak), let it harden.

Place the bars on the ground at intervals of about 1 m, pin the boards to them, sinking the nail heads. Nails are better to use galvanized. Leave a gap of up to 5 mm between the boards for ventilation and water drainage.

Sew the shields together using the same bars. Treat the joints with sandpaper.

Paint the walkway using outdoor paint.

Walking path made of boards and gravel

Another design wooden walkway for the garden, simple in execution and does not require substantial costs. For her you need:

Prepare the base according to the above technology. But a trench 5-7 cm deep, covered with a sand-gravel mixture, is enough.

From the boards (beams), cut lengths equal to the width of the track. Process them in the same way that was used in the manufacture of shields.

Place the boards along the length of the base with an interval of short steps, press into the backfill, paint.

Plank flooring

As you can see, to create simple but spectacular wood paths with your own hands, special knowledge and skills are not required. Consider the recommendations, take a closer look at the photographs, turn on your imagination and decorate the territory in the country with original paths.

All buildings and structures (gazebo, terrace, swimming pool, greenhouse, vegetable garden and various elements of landscape design) on the dacha or personal plot communicated through tracks.

What kind of path to make, or rather, from what material, everyone decides for himself, specifically within the framework of this article, we will consider the manufacture of a garden path from chopped tree rings.

Among all the options (from boards, timber, shields, garden parquet, branches and bamboo), one of the most accessible in terms of material and the most difficult in terms of device is the path from tree cuts. The material is structured according to the principle step by step instructions so that anyone can build such a path with their own hands.

A path made of wooden saw cuts can be called differently: from cuts, stumps (dice, block, stump, log, ends of logs), but the construction method will be identical.

Garden paths from saw cut wood - step by step guide

For work you will need materials and tools:

Saw cuts (cuts) of a tree
Roll waterproofing or geotextile (geotextile)
Sand, pebbles, gravel, water
Level
Hammer (preferably a mallet)
Chainsaw manual
Shovel, buckets, brushes

Step 1 - preparation of wooden saw cuts

You need to start working with pre-training saw cuts (cuts) of a tree. Then they will be ready just in time for laying.

When choosing wood, you need to proceed from how long it is supposed to operate the track, and what load it will have. When arranging garden paths from tree cuts in the country, it is better to give preference to hardwoods. So, for example, oak will serve you for about ten years, pine - no more than seven. And larch is practically indestructible and will delight you for more than a quarter of a century.

But, most often, blanks for the track are made from those rocks that are available. It all depends on the budget, saw cuts from poplar will cost much less than from oak or larch.

To prepare the cut, you need to dissolve the log into pieces 150-200 mm high.

The rule works here, the larger the diameter of the log, the greater the saw cut height should be. And of course, the height of all blanks should be approximately the same.

If the thickness of the saw cut is less than 100 mm, there is a high probability that it will not be fixed in the ground, and may “pop out” when pressed.

To extend the life of the saw cut, it must be cleaned of bark. Because it is the bark that will begin to flake off first.

In addition, it is better to refuse to use saw cuts that have cracks. They will begin to deteriorate first of all and very quickly, and the crack may increase under the influence of loads on it.

The saw cut must also be pre-processed. The most common can be called drying oil treatment.

To do this, it is heated to a boiling state and the saw cut is completely coated. Please note that this work is dangerous, so it is better to buy special antiseptic solutions that will provide both moisture protection and biosecurity. In such a solution, the saw cut should be from two hours to two days.

To protect the wood from decay even more reliably, the bottom of the round timber must be additionally treated with bitumen. Wood can be aged with a solution of copper sulphate.

The treated saw cut must be dried well.

Step 2 - marking the track

The complexity of this step is in determining optimal sizes paths - 350 mm, sufficient width for one person to move freely. As well as its route - to provide access to all the required objects.

Step 3 - ground preparation

In order for wooden garden paths to serve you as long as possible and be safe, they must be securely fixed.

To do this, along the marked route of the future path, you need to dig a trench. Its depth depends on the length of the hemp (cut) plus 50-100 mm. (depending on the type of soil and the expected load on the track).

The width of the trench is equal to the desired width of the path.

A waterproofing film is laid on the bottom of the trench (you can apply polyethylene film used for greenhouses or geofabric).

Gravel or small gravel is poured over the film. This drainage is necessary in order to protect the wood from moisture. The height of the first layer of the cushion is half of the required height (25-50 mm). It is important to pack it well.

The sand and gravel cushion must be leveled using building level. This will significantly save time and effort when laying saw cuts.

Step 4 - installation of curbs for tracks (sides)

If a curb is provided, then they must be installed before the installation of saw cuts.

Stones, bricks, sheet iron, wooden blocks or long logs can be used as material for the curb.

But, in order not to disturb the harmony of the garden path, chibouks sawn along are used.

Step 5 - filling the second layer of sand cushion

Sand is used as the second layer. The total height of the pillow is 50-100 mm.

To compact the sand well, a technique such as watering it with water is used.

The material was prepared for the site www.site

Step 6 - scheme for laying saw cuts from wood

The order in which the wood slices are mounted is not critical. The formation of the pattern depends on the preferences of the owner.

It can be positioned so that there is as little space as possible between the cuts. And you can, on the contrary, arrange them widely.

The main thing at this stage is to slightly “drown” the saw cut (tamp it down), and also align them in level.

Step 7 - decorative design of a garden path from tree cuts

The space between the cuts can be covered with sand or earth mixed with seeds of ground cover plants.

And leave the cuts themselves in their original form or paint with bright colors.

You can more clearly show how to make paths from tree cuts using a sectional drawing of a path.

Caring for wooden walkways

So that a self-made garden path made of saw cuts of a tree does not lose its original appearance over time, it needs constant care.

To do this, once a year you need to clean the saw cuts with a metal scraper, treat with an antiseptic and apply a special protective covering, drying oil or paint.

Advice
When you make a track, set aside a few saw cuts in reserve, in the future, it will be possible to replace individual elements in the process of repair. In order to reduce the sliding effect after rain, do not polish the ends of the logs heavily before installation.

If you are interested in the process of arranging a path from tree cuts - a video illustrating DIY manufacturing

Garden paths from saw cuts of a tree - arguments "for"

cheapness;
high speed and ease of arrangement;
the ability to carry out the entire process independently;
do not accumulate moisture (do not create puddles);
have a natural appearance;
very maintainable;
environmentally friendly;
opportunity to make a unique garden path from wood. After all, all saw cuts are different, which means that it is impossible to repeat the pattern;
the ability to use end-of-life logs as mulch or chop and add to compost.

Country paths from saw cuts of a tree - arguments "against"

subject to decay;
react to temperature changes;
require constant care;
become how many after the rain (leveled by using a special composition for processing).

Conclusion

Based on the foregoing, it becomes clear how to make a path from tree cuts with your own hands, without resorting to excessive costs and outside help. Although, you should not rely too much on cheapness, even with self-manufacturing you have to spend money, but such a path is worth it

The saw cut floor is made of natural materials who do not have any negative consequences for good health. Due to the fact that it is made from natural resources

Benefits of saw cut floors:

The saw cut floor is made from natural materials that do not have any negative health effects.
Due to the fact that it is made from natural resources, it can be very cheap.
Contrary to the opinion of skeptics, such a floor is more durable than expected.
Exceptional aesthetic appearance and pleasant to the touch.
Easily done without the need to hire a specialist.

Disadvantages:

Unfortunately, this type of flooring requires quite a lot of wood. good quality, so it is recommended to cover only small areas(to protect forests).
Require frequent Maintenance(every 2 years)

Construction stages:

Before proceeding with the creation of such a floor, it is very important to read information about natural houses, floors in which can be not only inexpensive and healthy, but also very effective, because they form a thermal mass and act as a heat storage from sunlight or any other source of energy.

Materials:

Pieces of logs are about 10-12 cm thick (the diameter may differ from everyone's imagination).
sawdust, limestone, clay, linseed oil, beeswax, water, lard.

Note: it is important that the cuts are very, very well dried (not to mention work, no moisture).

The manufacturing process of such a floor is relatively simple and is very similar to laying paving slabs or paving stones. You need a hard, well-packed surface, on top of which we pour a layer of river pebbles (about 6-10 cm). Then, using a rubber mallet, we proceed to laying the saw cuts. We tap and check with a level that the floor is even and none of the saw cuts stick out or go too deep. As a rule, after laying, the distance from the surface of the cuts to the level of the sand is about 4-7 cm, and the distance between the cuts should be approximately one to one and a half centimeters.

Joint filler mix:

For a floor area of about 5 square meters in a 15-liter bucket for 1 kg of melted pork fat, add 1 kg of lime, 5 kg of sawdust and 2 kg of clay with water. After thorough mixing, you should get a pasty mass. You can also add marble dust or glass shards with grease to help make the mixture waterproof.

We introduce the mixture into the distances between the cuts and rub it well, as far as possible, without leaving air pockets. It should fill the gaps up to the magazines. It is very important that there are no voids left, otherwise cracks and water leakage cannot be avoided in the future. Residues of this mixture can also be used to fill cracks in saw cuts (if applicable). After the last seam is smeared, we leave our floor to dry for 1-2 days. Check if you have cracks, then fill them. After complete drying (another day or two) it is well polished. Even scraping is recommended. You can rent a cycling machine to achieve the perfect effect. After that, once again carefully, very carefully check if you have any cracks. If found, fill in gaps, hand sand and leave to dry completely. This usually shouldn't happen after scraping, but especially if you're using a bathroom floor like this, it never hurts to be more careful.

And finally, it's time for the most pleasant stage of finishing. Since our floor is made of natural materials, we will polish it natural materials, namely beeswax and linseed oil.

Benefits of sawn floors

The saw cut floor is made from natural materials.
Relatively cheap.
Very beautiful and pleasant to the touch.
Easy to do (relatively).

disadvantages

Unfortunately, this type of flooring requires quite a lot of good quality wood, so it is recommended to cover only small areas.
Saw-cut floors need to be serviced about once every 2 years.

What will be needed?

Kruglyashi 10-12 cm thick, sawdust, limestone, clay, linseed oil, beeswax, water, lard.

Note: it is important that the cuts are very, very well dried (not to mention work, no moisture).

The manufacturing process of such a floor is relatively simple and is very similar to laying paving slabs or paving stones. You need a solid, well-packed surface, on top of which we pour a layer of river pebbles (about 6-10 cm). Then, using a rubber mallet, we proceed to laying the saw cuts. We tap and check with a level so that the floor is even and none of the saw cuts stick out or go too deep. As a rule, after laying, the distance from the surface of the cuts to the level of the sand is about 4-7 cm, and the distance between the cuts should be approximately 1-1.5 cm.

Joint filling compound

For a floor area of about 5 square meters, in a 15-liter bucket for 1 kg of melted pork fat, add 1 kg of lime, 5 kg of sawdust and 2 kg of clay with water. After thorough mixing, you should get a pasty mass. You can also add marble dust.

We introduce the mixture into the distances between the cuts and rub it well, as far as possible, without leaving air pockets. She has to fill in the gaps. It is very important that there are no voids left, otherwise cracks and water leakage cannot be avoided in the future. Residues of this mixture can also be used to fill cracks in saw cuts (if applicable). After the last seam is smeared, we leave our floor to dry for 1-2 days. If cracks appear, fill them.

After complete drying (another day or two), we polish the floor from saw cuts well. Even scraping is recommended. You can rent a scraping machine to achieve the perfect effect. After that, check very carefully for cracks.

Finally, polish with beeswax and linseed oil.

p.s. And this is an old "pavement" of saw cuts, which the craftsmen gave a hexagonal shape (the shape of a honeycomb), it is over a hundred years old.