How to glue vinyl wallpaper? How to glue vinyl wallpaper on a paper basis. How to choose and stick vinyl wallpaper on paper or non-woven base

Vinyl wallpapers are ideal for both new buildings and for decoration during renovation. About how to glue vinyl wallpapers you will learn from our article.

Tools and materials

For work you will need:

• A special brush or fur roller for priming walls and applying glue.
• Rubber roller for working with seams.
• Yardstick.
• Level or plumb line.
• Paper tape.
• Cotton rags (to remove excess glue).
• Scissors, knife for cutting fabrics.

Process details

How to stick vinyl wallpaper: work sequence

1. Preparing the walls

• The walls must be well dried before gluing, especially if plastering work was carried out before that.
• The surface should be without visible drops, potholes, chips.
• Walls are primed with diluted glue or primer deep penetration. It is preliminary recommended that the walls be treated with an antifungal compound (anti-fungus primer or any fungicidal compound).
• Clay gets divorced warm water according to the instructions on the package.
• A vertical line is beaten off using a level or plumb line, which will serve as a guide for gluing the first sheet.
• Then it is necessary to de-energize the room and remove sockets and switches from the walls.

Your attention! The walls are cleared old finish, cracks are puttied, and the surface is leveled. How to check if the walls are well dried? Glue a small piece polyethylene film if water droplets appeared on it overnight, the wall needs to be dried better.

You can also check the wall for the degree of preparation by gluing a piece of ordinary tape to it. By sharply removing it and looking at the back, it will be clear how the wall is prepared.

Wallpapering

The presence of paint or plaster residue on it indicates poor preparation of the surface or any other room.

Before gluing vinyl wallpaper, you need to make sure that there are no drafts in the room, in no case should you turn on fans and air conditioners, open windows until the canvases are completely dry.

It is impossible to stick canvases on old ones; they must be removed by moistening them with water beforehand. A similar procedure is followed.

2. Training

The rolls are cut into strips, leaving an allowance of 10 cm in length. If the coating has a pattern and its selection is required, when cutting the strips, you need to combine the pattern, not forgetting to leave an allowance.

3. We apply glue

After the wall is leveled and dried, the glue is prepared for application (it should stand for 10 minutes after stirring), you can start gluing the canvases.

Vinyl sheets are glued end-to-end, without overlapping sheets on each other. Glue is applied to the size of the first sheet, glued on and proceed to the preparation of the next section.

When gluing, make sure that no glue remains on the front side of the canvas, especially when working with light shades.

Your attention! When gluing vinyl coatings based on interlining, glue can not be applied to the sheet.

Before starting work, read the instructions on the package, and just that.

4. Trimming the edges

After gluing, an allowance remains near the plinth below and above, which must be cut with a sharp blade.

Advice! It is best to cut the coating when it is well dried, otherwise you will not be able to make an even, neat cut. The knife blade needs to be changed periodically.

Classic technology

Vinyl coating is best glued in a duet. One at the bottom cuts the canvases and applies glue to them, the other sticks a strip on the ladder-ladder and pre-applies glue to the wall.

The panels are pressed against the base of the wall and the bubbles are forced out with a roller from the center to the edges and from top to bottom.

If glue remains on the edges during gluing, you should immediately wipe them with a soft cloth or sponge.

Skirting board sticker

If it is not possible to remove the plinth, the sheets are carefully cut at its upper edge.

Work at the top

To prevent the glue from getting on the painted ceiling during work, you need to wrap the panel 5 cm at the top. After gluing the strips, glue this area, applying glue with a small narrow brush.

Corner finishing

Corner finishing options:

• You can glue the canvas in the corners with an overlap. This method is applicable for plain canvases and specimens with a small pattern. When gluing, the sheet is placed on the adjacent wall by 1 cm, this overlap is subsequently covered with an adjacent sheet. This sheet is also glued along a strictly vertical strip.

A special glue is used for gluing the panels with an overlap. The disadvantage of this method is the unaesthetic appearance of the corner.

• Another way - the work begins in the same way as the first method, but with a large (2-3 cm) allowance. After drying the canvases with a clerical knife, two sheets are cut vertically at once.

For this purpose, a spatula or a metal ruler is used, along which two layers of sheets are cut from bottom to top. The cut off parts are removed, the edges of the canvases are bent, glue is applied and rolled with a roller or plastic spatula. The seam in this case is perfectly even.

Finishing near batteries, switches and sockets

Advice! Behind the heating radiators, the wallpaper is let in 15-20 cm and pressed against the wall with a narrow roller. Behind the batteries, you can not stick canvases, but paint the wall to match.

In places where there will be sockets and switches, the gluing process takes place in the usual way. It is not necessary to pre-cut holes in the sheet, as they may not coincide with the technological holes for electrical outlets. This is done after gluing the panels.

Vinyl wallpaper on paper basis

The principle of operation differs little from the usual, with the exception of a few points.

Vinyl wallpaper on paper basis many people know how to glue, since they have been traditional for a long time.

Glue is applied to the surface of walls and panels. On the sheets, the glue should impregnate the base; for this, the panel is folded face to face and left for some time.

Heavy vinyl wallpaper

This type of glue is somewhat more difficult than paper-based materials. It will not be easy to master this work on your own, especially if there is no experience in this matter.

Before gluing heavy vinyl wallpaper, purchase a special glue. We recommend using Quelyd, KLEO Line Optima or Metylan Interlining.

Such a finish stretches when wet and narrows when dry, which affects the quality of the seam.

The glued canvases should not dry too quickly, so the room temperature should not exceed 15 °C.

Summing up

We hope our article was useful to you. In order to more accurately understand the technological and practical matter, on our website there is a detailed photo and video instruction in which you will find useful information on this issue.

Photo gallery

When choosing wallpaper for a room, you should follow some rules and do not forget that they are not suitable for small rooms. bright wallpaper from large pattern. They visually further reduce its area. It is best for such a room to choose light wallpaper. If you want to visually increase the height of the ceiling, then the most appropriate would be the use of wallpaper in a narrow vertical strip. IN
In this article, we'll look at .

From this article you will learn:

We glue correctly paper-based vinyl wallpaper, a few steps.

Preparatory work
Before proceeding with the sticker paper backed vinyl wallpaper surface preparation is required. It must be leveled to get rid of defects with putty and cleaned of old wallpaper with a spatula and ordinary water. In this case, the wall must be not only absolutely flat, but also dry. When working, there should be no drafts, the windows are closed, and the air conditioner is turned off. So that subsequently a fungus does not appear under the wallpaper, it is recommended to treat the wall with a special substance.
The first step is to prepare the glue. It is diluted with water in the amount indicated on the package.
While the glue is being prepared, you can start cutting the wallpaper roll into strips with an allowance of at least 10 centimeters.
This is important, this must be remembered! The glue is applied to the vinyl wallpaper, not to the wall! After that, the canvas folds in half for 5-10 minutes. Now you know, .
Now the wallpaper needs some time to swell. In this case, the fibrous parts of the paper are impregnated, and the wallpaper material becomes more pliable and stretches.
The technology of gluing paper-based vinyl wallpaper is practically the same as other technologies. Work starts from one of the corners. In this case, wallpaper canvases should find each other by no more than 3 centimeters. It is much more convenient to do this together with an assistant, when one stands on a stepladder, and the other combines the edges of the wallpaper end-to-end, holding the bottom of the strip. If glue gets on the wallpaper, it must be immediately wiped off with a dry soft cloth.
By leaving an allowance when cutting wallpaper, their excess is formed under the ceiling, which must be carefully cut off. To do this, use a sharp wallpaper knife.
Before proceeding with wallpapering, the sockets and switches in the room are removed, and the electricity is turned off. The wallpaper is glued directly onto the holes, and then, after drying, cut around them, and the sockets and switches are returned to their place. You may need to remove air from under the wallpaper. This is done easily with a special rubber spatula or with a dry cloth or a large soft roller.

Since ancient times, people have been decorating their homes using wallpaper. But if in the recent past, they were only of two types - expensive fabric and cheap paper, today the range of materials is much wider. In this article we will talk about vinyl wallpaper.

Why about them? Everything is very simple - this is a material that simultaneously combines affordability, quality and a wide variety of textures and colors. After reading the article to the end, you will learn how to glue vinyl wallpaper correctly, saving your strength and nerves as much as possible.

The key to quality when wallpapering is 90% the base on which the roll coating will hold. If you do everything right, you will forever forget about peeling edges and swollen seams.

So let's get started.

Removing the old trim

The first step is to remove from the walls everything that will interfere with further work.

If there are old wallpapers in the room being renovated, then they must be removed to the very foundation (see). Of course, if you do not want to breed dirt and do not chase the perfect appearance premises, please leave them. But in this case, the quality is out of the question.

• To make your task easier, use special means to remove wallpaper. It perfectly penetrates the surface structure and softens the old dried glue.
• The instruction of this composition says that it should be enough for 200 square meters, but do not rush to trust marketers. In fact, this figure is calculated on the coincidence of all favorable conditions (smooth walls, a surface with high adhesion, etc.), and on walls where there are, for example, two layers of wallpaper, the consumption increases significantly.
• We’ll tell you in secret that instead of it you can use a composition, the average price of which is 30 rubles per cubic meter- This is water. It impregnates the surface a little worse, but the money saved is better spent on a better glue, for example - Quelyd (a great French-made glue that leaves even well-known competitors like Metylan far behind).

Before repairing, buy yourself a plastic bath and a roller - we will use them to apply all the compounds that we will encounter along the way. The advantage of a bath over a bucket is undeniable, since the ability to remove excess moisture from the tool allows you to perform all work more accurately.

Wet the old wallpaper well (two times is better), and let it soak for five minutes, then start removing it. To do this, use a wide (20 cm is enough) sharp spatula. If the lower layers are poorly saturated, then repeat the treatment with water - and so on until complete cleansing.

The photo above shows the wall after the wallpaper has been removed. Such a picture is easy to find in almost every apartment that contains traces of Soviet decoration. Before you is the bottom layer of oilcloth wallpaper glued on PVA, which is very difficult to remove.

Further we see large craters on the surface of concrete - a frequent occurrence in houses with thin partitions. It occurs as a result of drilling a wall (mounting doors, canopy of furniture and accessories), and if you look closely, you will see the shiny tips of the anchors that are clogged from the back.

Well, there is nowhere to get away from the peeling putty, which also needs to be cleaned off before solid foundation Whether it's concrete or plaster. If a surface painted with enamel is exposed under the wallpaper, then do not rush to get upset, there is no need to remove it. Enamel is an ideal surface for wallpaper, with absolute adhesion, which will save you from the need to apply a primer.

Leveling the surface

The thinner and more expensive the wallpaper, the more even and smooth the surface is required for them. Remember that each bulge on the wall leads to deformation of the canvas, which complicates the smoothing and joining of the seams, therefore, it is best to start by leveling the walls. But if you are not going to arrange a major overhaul, then you can limit yourself to patching potholes and puttying (see).

So:

• To begin with, we will use a dry brush and clean out all the dust from the chipped places. After that, it is necessary to thoroughly moisten the surface of the pothole with a primer - this will bind the remaining dust and improve adhesion. Let the soil soak in and dry.
• It is most convenient to close cracks using. It, unlike pure gypsum, has long time working out, and, thereby, allows you to do the job more carefully. This is a big plus for inexperienced people who decide to do everything with their own hands.
• The next step is to apply primer to the walls. Brush the corners of the room, as well as places under the ceiling and near the floor, separately with a brush, since here the wallpaper peels off most often.

Now we take a spatula in our hands, and in order to create a smooth surface, we begin to coat the wall with putty. The more layers you apply, the better the end result will be. But if the walls were not pre-plastered, then the feasibility of applying more than two layers is extremely doubtful.

After the wall dries, it needs to be sanded. Use an abrasive mesh of medium or fine fraction for this.

Next comes the crucial moment. correct execution which will greatly facilitate your work in the future - this is priming the walls under the wallpaper. It would seem nothing special, but in reality everything is different.

• Unlike a brush, when applying glue to the wall with a roller, it forms thin layer, which facilitates the process of smoothing and removing air from under the canvas. But due to the fact that the wall draws moisture into itself, such a layer is not enough for a long time, and the wall dries quickly. Because of this, you may not have time to properly smooth out the strip of wallpaper, and it will begin to peel off. The most annoying thing is that you will notice this only the next morning.
• Therefore, priming is carried out in several stages. First, apply a deep penetration primer to all walls (see). Do not artificially reduce the flow - the soil should literally drain. Give it half an hour to absorb and repeat the whole procedure again. Now you need to give 2-3 hours of drying time.
• For the third layer, we will prepare a solution ourselves from wallpaper glue. To do this, mix it with cold water in the proportions indicated on the package. We process the walls with the resulting mixture, and let it dry well.

Advice! Be careful, as there are two recipes on the package: one for priming, the other for gluing.

As for the ceiling, then add the following. All leveling, painting and installation work ceiling baguette must be completed prior to gluing. Finishing flooring(except for carpet) it is also advisable to lay it in advance so as not to damage the walls in the future. The exception is floor plinths, which are mounted last.

Sticking wallpaper on the wall

The main feature of vinyl wallpaper is the presence of a layer consisting of polyvinyl chloride applied to a paper or non-woven base. In fact, it is an ordinary plastic that has some elasticity.

Softening the structure

There are wallpapers in which, either low-quality vinyl, or there is too much of it, because of which they are poorly impregnated and extremely reluctant to change the shape that they took as a roll.

That is why all vinyl wallpapers, even on a non-woven base, must first be impregnated with glue. In the language of wallpaper masters, this procedure is called "brewing". Let's see how to do it correctly.

Measure a piece of wallpaper to the height of your room. In the place of the received mark, fold them in half, strictly making sure that the edges do not scatter when folded.

Cut the fabric at the fold using a utility knife or tailor's scissors. Buy several packs of blades for a clerical knife at once, as they become dull very quickly when cutting paper.

Advice! If the wallpaper you use does not have a pattern that needs to be joined together, then to speed up, cut the entire roll at once.

Spread the resulting piece on the floor, and spread a thin layer of glue on it with a roller. Make sure that the edges of the canvas do not remain dry. In order to prevent debris from sticking to the roller, which will then fall on the wallpaper, do not forget to rinse the floor with a damp sponge every time before applying glue to a new batch of wallpaper.

In order for the wallpaper to be better saturated, they must be folded. To do this, we bend both edges in turn towards the center, making sure that they do not overlap each other. Then we fold them two more times and put them aside, allowing them to stand in this form for at least five minutes.

Do the same with all the other cut pieces. In order to have time to produce such blanks, you should not brew more than five pieces at the same time.

Location on the wall

After we unfold the already impregnated wallpaper blank on weight, and apply it to the intended place. We join the seams with the already glued parts, and begin to smooth the canvas from the bottom up. For this procedure, you will need a special trowel and a rubber roller, which effectively expel air and excess glue from under the wallpaper.

When gluing the first piece to the wall, it must be aligned vertically, for which use building level to be attached to the edge of the canvas. To simplify your task, first draw a vertical line on the wall.

Advice! If you see that the seams between the wallpaper do not adhere well, then additionally grease them with glue.

Now you need to cut off the excess wallpaper along the edges of the canvas. If the lower part may not be even (the edges are closed with a plinth), then on top - every millimeter counts.

For precise cut perform the following actions:

• We bend the wallpaper under the baguette, pushing the corner with a plastic wallpaper spatula.
• Next, we apply a long metal spatula to the corner from the side of the wall, thereby fixing the canvas.
• Using the edge of the spatula as a guide, cut through the paper with a clerical knife. This method is difficult to apply if the wall is curved, and does not allow you to apply the spatula evenly. In this case, it is better to rely on your eye, as the master did in the photo below.

Do not forget that wet wallpaper is very easy to tear. Therefore, use only sharp blades, changing or breaking off sections of them every time you feel that they have become worse at cutting. While cutting, hold the knife at the sharpest possible angle relative to the wall.

So:

• Wallpaper is cut in a similar way when joining edges that do not have factory seams. Most often, this technique is performed over the door and window openings, in the corners of the room and in inconspicuous places. It allows you to avoid such a phenomenon harmful to aesthetics as gluing with an overlap.
• Let's see how this is done in practice. When the wall is glued on both sides at the same time, there will certainly be a section in the middle, the width of which will not match the width of the roll. We cut off a piece desired length and glue it, joining along the seam on one side, and overlapping on the other.
• We smooth the canvas, and feel for the border of the lower canvas. We retreat from it 1-2 centimeters, apply a spatula and cut through both layers. Then we bend the edges, and take out the resulting trimmings. Lubricate the wall again with glue, and rub the resulting seam with a trowel, which is very often more inconspicuous than the factory one.

The whole further procedure is monotonous and monotonous, so, having mastered all of the above, you can easily tell anyone how to stick vinyl wallpaper yourself. To strengthen your theoretical knowledge, also pay attention to the video that we have selected for this article. Well, of course, try, create and fix educational material on practice.

How to glue vinyl wallpaper? This question is asked by many owners during cosmetic and overhaul, because it is vinyl already long years most valued among different types wallpaper.

The best value for money, durability, resistance to impacts and scratches, the most unusual colors and patterns - all this is vinyl.

Sticking a vinyl sheet with your own hands is a rather troublesome business, but it’s quite possible to cope if you prepare the surface well and study all the nuances of such a wallpaper repair.

Advantages and disadvantages

They are produced in the form of rolls with a base of paper web or better and more durable non-woven fabric, on top - a decorative layer of vinyl (officially - polyvinyl chloride).

This coating has several varieties, but they are all famous for a number of common advantages:

• strength (due to two layers of canvas, it is almost impossible to tear the vinyl when gluing or already on the wall);
• durability (perfectly kept on the wall for up to 10 years, while maintaining the original brightness);
• moisture resistance (some types of vinyl can be wiped with a cloth and even washed);
• versatility (you can choose a coating for any interior, find an imitation of any coating - wood, fabric, brick, etc.).

Among the disadvantages of vinyl are toxicity, airtightness and heavy repairs, but in fact - not everything is so dangerous.

Toxic fumes after finishing can only appear on wallpaper of dubious quality - proven non-woven vinyl is absolutely safe for health.

This coating is also highly breathable, unlike a heavier paper backing that can encourage mold and mildew growth.

Gluing vinyl wallpaper with your own hands is really not easy, especially in the absence of experience, but if you choose a light coating on non-woven, rather than paper-based, then the gluing process will be much easier.

Features of gluing different types of material

Where to start sticking vinyl wallpaper?

Many will say that from a window or from a wall and they will be almost right. But in fact, you need to start by choosing a type of vinyl sheet.

On the repair market, you can find several subspecies of such a coating, each with its own characteristics.

• Structural (with a layer of foamed vinyl). Such wallpaper is usually pasted over uneven walls, as well as wood, plywood, fiberboard. The canvas helps to smooth out all the bumps and defects and creates a spectacular play of light on the surface;
• Hot stamping (heavy and compact vinyl). Such dense wallpapers are produced in the most unusual colors and textures. They perfectly hide all the unevenness of the walls and last as long as possible without losing their original appearance;
• Silkscreen. These rolls are produced on a paper basis. Stickering such wallpapers with your own hands is not an easy process: heavy silk-screened canvases are glued end-to-end, without overlap, and besides, when dried, they can shrink. But they are very durable, resistant to abrasion, look invariably expensive and stylish;
• Washable. Such vinyl is commonly used for kitchen renovations;
• Solid (evaporated). Consists of three layers of paper and evaporated vinyl, often used for painting.

Preparing for wallpaper repair

How to glue vinyl wallpaper with your own hands and what is needed for this?

You need to start by preparing a bridgehead for repairs - get rid of all traces of the old wall covering: greasy dirty wallpaper, crumbling putty and plaster.

Even if it is planned to paste the wall with embossed vinyl wallpaper, it is necessary to smooth out large cracks and bumps with putty, as well as prime the surface so that the vinyl lies tightly and does not peel off.

If wide vinyl wallpapers are used for wall decoration, it is important to ensure a perfectly flat surface.

Before you glue vinyl wallpaper with your own hands, you need to prepare:

• sharp scissors or a special wallpaper knife;
• pencil, suspension with a piece of chalk, ruler;
• a wide brush for glue and a thin brush for joints;
• wallpaper (plastic) spatula and rubber roller (smooth heavy canvases);
• clean dry cotton cloth;
• wet sponge;
• a bucket for glue and glue itself;
• ladder;
• several old newspapers.

Before gluing vinyl wallpaper with your own hands, you also need to de-energize the room and close all windows and doors tightly so that drafts do not walk in the room.

Then you need to properly prepare the glue and cut the wallpaper. Special glue for vinyl wallpaper is diluted according to the instructions and waiting for the solution to swell.

In the meantime, you need to prepare the wallpaper strips: cut the roll into separate canvases along the length with an allowance of 10 cm, lay them out on old newspapers, spread wallpaper glue and leave to “ripen” for 7-10 minutes.

Vinyl wallpaper gluing: work technology

How to glue vinyl wallpaper in a room with your own hands? It is best to do this together - with a reliable assistant.

First you need to draw a vertical line on the wall with the help of a suspension - the first strip will be glued along it.

The process of gluing the wallpaper will look like this: one person takes the wallpaper soaked with glue for upper part, gives it to a partner standing on a stepladder.

He applies a piece of vinyl roll to the wall, unfolds the panel and aligns the wallpaper.

It is necessary to glue vinyl only end-to-end, even minimal overlaps are strictly prohibited.

Then the strip must be smoothed out with a rubber roller or spatula.

The trowel is ideal for smooth canvas, the roller is used for foamed vinyl and other embossed wallpaper not to damage the pattern.

Where to start smoothing the canvas to expel trapped air and remove excess glue? It is better to move from the center to the edges from top to bottom in order to squeeze out all the bubbles.

Excess glue must be quickly removed with a cloth so that it does not get on the front side of the wallpaper.

Excess wallpaper that remains below should be cut off after drying, otherwise the wet canvas will wrinkle and may even tear.

Wide vinyl wallpapers are glued in the same way as strips of standard width.

The only caveat is if you choose wide wallpaper, then when working it is convenient to use 2 ladders. This will ensure the perfect alignment of the wallpaper on the walls and make it easier to lay them end to end.

Where to start wallpapering?

It is better to lay a vinyl sheet on the wall from the corner of the wall perpendicular to the window, light wide canvases - from the window in the direction of the incident light.

This will allow you to glue the wallpaper exactly end-to-end, clearly connect the pattern and create the effect of a solid coating.

We glue vinyl wallpaper in problem areas

If the process of pasting the walls themselves with heavy vinyl looks quite clear, then how to glue vinyl wallpaper in problem areas and where to start work?

The most difficult areas for do-it-yourself wallpaper repairs are the corners, the space behind the battery and the switch sockets.

Where to start wallpapering the corners with your own hands and how to do it - end-to-end or overlap?

To make the corners look beautiful and not lose their appearance after drying, you need to act according to a special scheme.

We glue two panels on the corners with an overlap of 2-3 cm (if the corners are uneven, you can increase it to 5 cm).

Then, with a sharp clerical knife, we cut both pieces vertically - along a ruler or a long spatula.

Carefully remove the upper unnecessary strips, bend the edges of both canvases, coat with glue, lay them back on the wall, connect the pattern and roll it with a roller (spatula).

After drying, the corners will remain perfectly even.

It is not necessary to lay the vinyl completely behind the batteries - it is enough to glue 15-20 cm on both sides.

If you definitely want to decorate the area behind the radiator with wallpaper, then you can cut pieces of the canvas into several narrow parts - this will make the job easier, especially if wide wallpapers are used for decoration.

Places for sockets and switches, when pasting walls with vinyl wallpaper, need to be cut out only on the wall - if you make holes in advance, they may simply not coincide with a real outlet.

On the glued strip mark Right place, make cuts crosswise and bend the corners inward.

After mounting the switches and sockets, the excess vinyl can simply be cut off.

Home repair is a troublesome business, especially when it comes to interior decoration that sets the tone for the entire interior. The presence of errors can spoil the entire design of the room. We will help you avoid them by analyzing in detail how to glue vinyl wallpaper on the ceiling and walls.

General provisions

First, let's pay a little attention to the chosen material. Why exactly vinyl wallpaper, what is special about them? Everything will become quite clear after reviewing their qualitative characteristics.

Advantages

The products in question are a non-woven or paper base coated with a layer of vinyl.

This structure provides them with many advantages:

• moisture resistance. Excellent quality, which is unusual for most other types of wallpaper. But vinyl not only resists moisture quite reliably, but is also able to withstand wet cleaning using household chemicals and even painting.

• Wide range of possible models. In addition to a stunning selection of a variety of ornaments and colors, there are also textured and silkscreen designs.

• High resistance to mechanical damage, ultraviolet radiation and even temperature fluctuations. That is, if you are opposite the south window, get a cat and begin to arrange long-term ventilation in winter, they will still retain their original appearance.
• Long service life, which reaches ten years.
• Simple sticking instructions, which we will analyze further in all the subtleties.
• Acceptable price. The whole set strength characteristics It is quite affordable for the budget of the average man in the street.

Flaw

The only thing that can happen unpleasant after applying the wallpaper in question is the presence bad smell the first two months. But this is subject to the purchase of cheap samples from an unknown manufacturer. Qualitative models do not have this effect.

Tip: if you still managed to stick foul-smelling canvases, and even airing does not help, then it is recommended to paint them with acrylic paint.
The polymer layer will block the contact of vinyl and air, eliminating the spread of odor.

Application technology

First of all, you should prepare everything necessary for the implementation of finishing work.

Tools and materials

For work you will need:

• Velor roller. Simplifies the processing of canvases and walls.

• Brush. Allows you to qualitatively cover hard-to-reach places with glue.

• A clean bucket for diluting the adhesive mixture.

• Special bath with ribbed surface.

• Stepladder - so that you can get to the top of the wall and ceiling.

Tip: choose a ladder that has a shelf on top.
Then you will have where to put the container with glue.

• Metal or plastic. It makes cutting fabric much easier.

• Roulette for all necessary measurements.

• Stationery knife for cutting wallpaper.

• Brush for smoothing products on the wall.

Tip: before gluing heavy vinyl wallpaper, be sure to make sure that the prepared brush is sufficiently stiff.
Because soft bristles will simply crumple on dense canvases and will not cope with their task.

• A clean rag to remove spilled drops of glue on the front side of the finish.

In addition to tools, you need to take care directly of the materials themselves:

1. Wallpaper choose in accordance with the rest of the interior of the room and its functionality. products designed for painting are better suited, and for the living room, for example, silk-screen samples. The color scheme is also very important and can have a significant impact on the feel of the occupants, visually expand and narrow the room.

1. How to determine when buying which adhesive is best for vinyl wallpaper? There are no secrets in this and you should not invent something new. Just read the attached instructions for the glue, and check with the seller for details.

1. Putty. It will be necessary if large cracks and significant damage are found in the wall after removing the old finish.

Preparatory work

Before sticking vinyl wallpaper, you must carefully prepare the surface of the wall.

Although such large-scale work with perfect alignment, as in the case of using paint, is not required, some things still need to be done:

1. Removing the old lining:
   • We wash off the paint with a special chemical composition.
   • We knock down the tile with a perforator.
   • We remove the wallpaper with a sharp metal spatula, after wetting it with water.

1. We putty possible cracks and noticeable irregularities.

1. We prime the wall. Do not refuse this step, even if it seems overhead and superfluous to you. The primer creates a polymer layer that increases adhesion, protects the surface from physical influences and reduces its porosity.

Sticking

Now let's figure out how to stick vinyl wallpaper:

1. We dilute the adhesive mixture with water according to the instructions indicated on the package.

1. We measure the wall, add a few centimeters and mark the resulting length on the unrolled roll.
2. Cut off the desired size according to the marked marks.

1. Apply glue to back side canvases. It is noteworthy that if products with a non-woven base are used, then this step is not needed.

1. Next, apply the adhesive to the wall.

1. We apply the canvas to the surface and smooth it with a brush, removing all the air from under it.

1. In the process, you will definitely come across the following question: how to glue vinyl wallpaper in the corners? The fact is that the corners in the room are almost never quite even, because of which you will not be able to make even joints there. Therefore, the canvas should be applied so that it covers trouble spot and entered the adjacent wall by at least 10 cm.

Output

We have examined how vinyl wallpaper is glued. The process is not complicated at all, but requires accuracy and attention. Stick to all the above recommendations, and you will succeed.

The video in this article will provide Additional information. Good luck wallpapering!