Crafts for the playground from logs and wheels - examples in the photo. DIY tire crafts: instructions on how to make interesting decorations and landscape design elements (105 photos)

The more colorful and varied the playground is, the more fun you can spend time on it. Even banal sandboxes and slides can bring a lot of joy to kids. And if skillful dads get down to business and make cars for the playground with their own hands, then the joy of the children will be no limit. For the manufacture of children's transport does not require expensive materials or complex tools. The work ahead is quite simple, even older children can be involved in it.

Transport for young riders

Game elements in the form of transport always attract the attention of kids. After all, sitting behind the wheel of an almost real truck or motorcycle, it is so easy to imagine yourself as a dashing racer.

The easiest way is to buy such a complex, but it is much more interesting to make it yourself. The main criteria that must be followed when making a car on the playground with your own hands are safety and aesthetics. All parts must be firmly fastened together, make sure that bolts and nails do not stick out. If the car is wooden, logs and boards are well cut off, protecting children's hands from splinters.

wooden train

Sawn wood train

Mobile sandbox

Idea for old tires

You can make a typewriter for a playground from a wide variety of improvised materials. Even if the game element only remotely resembles a real car, it doesn’t matter. Children's imagination knows no bounds, so a simple log can turn into a racing car or a passenger train. A mandatory attribute of any vehicle is the steering wheel. It would be great if it becomes a real steering wheel. However, it can also be done independently, realism is not at all necessary.

Wooden children's cars

Look at the photo - these wooden playground cars look very nice. To create them, you only need boards, logs and a little bright paint.

You can use ready-made boxes of different sizes. A truck body or a whole bus will come out of a large container, and a cabin will come out of smaller containers. It looks interesting sandbox, beaten under the car. For this, the sides are made higher, wheels are attached to the sides, and a cabin in front.

simple wooden car

By the same principle, you can make an unusual motorcycle for the playground with your own hands. Its basis will be a small bench, logs will serve as a rudder. Wheels can be real or cut from OSB sheet.

Tire toy vehicles

It is very popular to decorate a playground with car tires. Game elements made of such material are durable and, most importantly, safe. Rubber is less traumatic than wood or iron parts.

For the little ones

You can easily make unusual cars or a motorcycle for a playground from old tires. Such transport is suitable even for the smallest children.

Metal game elements

Craftsmen who own welding machine can build a metal car. Such a complex, which includes a small horizontal bar or ladder, is perfect for older children. If the car is supposed to have a seat, it is better that it be wooden.

A machine from a real old body will cause special delight. It is enough to clean it from rust, paint it in a bright color and attach the steering wheel. Thus, the thing intended for recycling will acquire new life.

Metal play complex made of pipes

Instructions for creating a simple wooden car

To make a wooden car with your own hands, you will need carpentry tools: hacksaw, hammer, planer, as well as nails or self-tapping screws. The material will serve as boards and OSB sheets.

Stages of work on building a truck with a sandbox body:

Raw boards are well planed and polished before construction begins. They are impregnated with drying oil for resistance to decay.
They make at least an approximate drawing of the future truck on paper, indicating the main dimensions. Mark the contours of the body and cab on the ground. To make it convenient for children to play, the part with the sandbox is made spacious enough, for example, 180 by 100 cm. The body can be of any size, but such that the kids can go there.
In place of the body, they remove the soil with a layer of 30 cm, cover the bottom with geotextiles or tarpaulins so that the sand does not mix with the ground. Four posts 40 cm high are dug in at the corners. Boards are screwed to the posts, forming a sandbox box that serves as a body.
Close to the sandbox, they begin to build a cabin. To do this, they dig in columns at the corners of the passenger and engine compartments, then screw boards or cut sheets of OSB to them. The hood cover can be made lifting using conventional door hinges. The place under the opening hood will serve not only for games, but also for storing toys.
A steering wheel is attached to the cab, and wheels made of tires or cut out of logs are on the sides of the car. The finished wooden car is being painted.

sandbox car

Do-it-yourself tire car

It is even easier to make a car from tires for a playground with your own hands than from wood. For work you will need 11 old tires from passenger car, 2 seat boards and steering wheel.

Stages of work on creating a car from tires:

They mark the contours of the car right on the ground and lay out old tires on them in order to have an idea of \u200b\u200bhow the finished car will look. Four tires are placed on the sides, simulating wheels. Five more pieces will go to the seats, and two more to the engine compartment.
Tires are removed and holes are dug under them. You don’t need to dig very deep, a third of the height for the wheels and half for the back will be enough. The distance between the wheels is made such that a seat fits between them.
They put the tires in place, after which they fall asleep with earth. At this stage, a steering wheel attached to a long pipe is installed. It must be firmly dug into the ground, because small racers will recklessly steer and can break the shaky structure.
Tires for seats are placed between the wheels, and on them are rather wide planks. The car is painted, decorated with headlights, old wheel covers.

Racing car from old wheels

Motorcycle for a playground from improvised materials

Making a play bike out of old tires is very easy. Two tires are dug into the ground one after another, and between them they leave a place to sit from a block of wood or plank. The steering wheel is obliquely fixed in the front tire. More complex models require three or four tires.

Stages of creating a motorcycle from four tires:

Mark the outlines of the motorcycle on the ground. If there is a small shop on the site, you can include it in the general ensemble, then you will need only three tires.
Two rear wheels are dug vertically to a third of the height, leaving a seat between them. The third wheel is driven in front.
Between the rear wheels, another tire and a board for sitting are laid. A steering wheel is attached to the front wheel.

Motorcycle for playground

There are a lot of design options for cars and motorcycles for playgrounds. The design can be complicated by adding additional tires or wooden elements. Undoubtedly, such vehicle, made with love, will become the main place for children's games.

Used car tires become a headache for ecologists and environmentalists. More than 70% of rubber tires in the world are not recycled and are collected in landfills. Meanwhile, the versatility and freeness of this material allows you to use old tires for new purposes. Craftsmen with a developed imagination create with their own hands both individual sculptures from tires on the playground, and entire towns.

Construction and arrangement of a playground from car tires

You rarely meet a motorist in whose garage there would not be a few tires that simply could not be thrown away. Do not rush to do this. Crafts from them are so simple and multifunctional that they will find a place both on the site, and in the design of the yard, and on suburban area and even as furniture.

A playground for children equipped with tires is a fairly common phenomenon. This material is almost universal for decorating sites with your own hands, sometimes there are real masterpieces. What are the most popular crafts among kids? First of all, this. Craft favorite place for games with one or more tires is easy.

Tires are exactly the material that does not require a large number of accessories, additions, tools and additional parts for strengthening.

Single tire sandbox

All you need for this craft is a big tire, a sharp knife, a piece of old garden hose, shovel, paints, if possible, in several bright shades.

It is better to choose a place for a future sandbox made of tires in the shade: the rubber gets very hot in the sun, the kids can get burned, and it’s more useful to play in the shade in the heat;
To begin with, you need to dig a recess with a shovel, a little more than a tire;
Cut off the inner ball with a knife and finish it cut rubber hose. This finish is needed to protect children from cuts;
Fill the tire with sand;
Paint in bright colors;
After the paint dries, the do-it-yourself sandbox will become a favorite place for children to play.

Sandbox Flower

Creating such a sandbox will take a little more time, but it will work bigger size, several guys can play it at the same time.

The design of the sandbox or flower bed type Tire Flower

DIY kit: 3-4 small tires, knife, construction stapler, shovel, paints, hose.

Tires are cut in half lengthwise and finished with a hose;
All elements are laid in the form of a flower in a shallow figured trench prepared in advance. Alternatively, in the place of one petal, you can install a round seat or stump, this will be a table or chair for parents;
At the junction, the parts of the tires are fastened together with a stapler;
It remains to paint such a seven-color flower and fill it with sand.

Sandbox with waves

This version of the sandbox can be of any size, for a whole group of children. You need several tires for manufacturing, depending on the diameter.

Swing

What playground is complete without swings. Sites equipped with various tire crafts will not be an exception, especially since there are many options.

The most important thing in mounting a swing with your own hands is to make reliable fasteners.

The place of suspension and ropes should be as strong as possible. As for varieties, the choice is yours.

The simplest

For older guys: the tire is suspended vertically on a rope or horizontally on two ropes. This option is made more attractive by cutting out all kinds of designs and figures from the tire. The main thing in this lesson is to leave the supporting sections of the tire as reliable as possible.

Cradle

Several options for swing tires

This swing is for small child. The creation process is as follows:

A small tire must be cut with a sharp knife to half so that the rims remain intact;
Prepare the attachment points, fasten the brackets and pass the rope through them;
Tie the ends of the rope on the rims on both sides.

Cradle - swing for the baby is ready.

rocking chair

Easy to do with your own hands and no less interesting for kids - crafts in the form of rocking swings. Needed Items: a tire, a board and something that can be used to make handles, for example, a simple thick rope will do.

Instructions for making a rocking chair from tires

The tire is cut in half (you can get two swings);
A board is attached to the cut part;
Holes are made in the board, a rope is fixed as handles. Handles can be carved from wood;
This is the simplest version of the rocking chair. If you connect your imagination and make a little more effort, the board-seat can be decorated with a variety of figures of animals, figuredly cut out the tire itself, color it brighter.

In past articles, we discussed in detail how to decorate garden plot and any other territory how to use dozens various ways and how to make a variety of creative and safe tires. Today we will raise the topic of children's sports grounds, which are one of the better ways disposal of a huge amount of used rubber, thereby helping environment, as well as the arrangement of courtyards and children's sports grounds where the state is not able to take care of it. For example, in the countryside, in remote ordinary villages and poor dacha-type villages, simply no one but yourself will build a playground, which is so relevant for children in the summer.

Similar children's sports grounds good large quantity a variety of projectiles in defiance of beautiful, bright, but very limited commercial courtyard structures. The main thing here is ideas, availability of hands and time. In addition to the wheels, you will need wood, as well as a lot of fasteners, bolts with nuts and sand, and maybe chains.

Remember that, despite the fact that children will walk on tires with their feet, rubber that has served its purpose on dirty and toxic roads must still be washed in a strong cleaning compound before use, then rinsing with high-pressure water.

So let's get started: ideas and short description. Pay attention in each example to the size and thickness of the tires and their parts. Key moment The assembly of such game considerations lies in the fact that each tire must rest against something above and below or be suspended from something - also most often both above and below, so as not to deform too much during use - under the weight of children.

First of all, these are, of course, bulk and hinged structures, along which you need to climb up: at an angle, vertically or onto some kind of three-dimensional figure.

This is simplest form- "Wall", when you need to climb on one side, climb over the crossbar from above and go down from the other side.

Vertical hanging wall made of tires on chains for older kids.

Another sloping wall where tires are nailed entirely to wooden canvas, and mulch or sand is poured between the tires and in them from below. Pay attention to the cable-cable going from above: you can climb the wall, grabbing the tires with your hands and resting your feet on the bottom ones, or you can climb, walking with your feet and sorting through the cable to keep the body position perpendicular to the canvas.

Analogue - without mulch, but tires different size so that the climb is absolutely safe, but a bit more difficult.

Again, a wall with a slope, but pay attention to the "goats" made of wood, as well as the fact that the two lower rows of the wall are made of tires, while the two upper rows above them are made of tire tubes.

Suspended wall with low slope for agility and balance training.

The same thing, but with a large slope and made of half car tire tubes:

An analogue is a hinged track made of tires.

All kinds of other three-dimensional structures for climbing:

Worth doing in 3 levels

And here ladders were made of tires, and they dug into a mound of sand and earth. In some cases, they were used as a ladder for slides.

Finally, a very interesting general "swing" of tires (for the company of children), on which you can climb, sit, but almost never swing.

A variety of hanging structures of various formats between the bars or the side support of the tires: in the middle of the tire can hang or be fixed / lie statically, positioned vertically or horizontally.

The next idea is tire tunnels, but the tires must be of the appropriate size. Tunnels can be ground or mounted (on chains) for older children (at the same time, tires must be fixed both from below and from above so that the wheel does not suddenly “leave” to the side when the child is inside) or on a beam (at the same time, so that someone - something did not fall out, tires should occupy all the space between the vertical posts). Using wood between large tires or concrete pipes. Inclined (tires are fastened together with chains so that the first do not gather at the bottom) and vertical.

Wood chip mulch is a very poor choice here, sand is of course much better

In fact, this is a fun arithmetic, but with the right tire size, this is a great tunnel for kids.

And here, in an excellent creative sports device for training the arms of the tire, there is a springy buffer platform for landing and pushing off with your feet.

Continuation - ideas for balance training complexes, large game objects and much more - see the second part of the article.

Source among others:
www.playgroundideas.org

If you are a modern parent, then the safety of your child is very important to you. Surely you do not want to let him go for a walk in various places that do not inspire confidence in you. And you don't have to. After all, today from simple materials you can arrange a playground with your own hands, where every child will like to spend their free time and play there various games. In this publication, we decided to offer you the most interesting crafts from the tires to the playground. We hope you will be tempted to make one of these and set it up in your child's play area.

What crafts to make from tires for a playground

Tire swing.

If you have old car tires at home, then you should not throw them away. It turns out that you can make a large number of crafts from them that can take their rightful place on the playground. Crafts from tires to the playground can be very diverse. Just look at the photos and find out for yourself the best way crafts.

The first and easiest craft option is a tire swing. To make such a swing is worth a little work. First you must position the tire horizontally. In it you must make 3 or 4 holes. Metal hooks are inserted into these holes. You must fix them with nuts and washers. And in the loops of the hooks you must thread strong threads or chains.

That's all the do-it-yourself swing from a tire is ready for your playground. And to make the swing look pretty, you can decorate it in a bright color.

Tire chairs.

On the playground, which you plan to equip with your own hands, it is worth installing comfortable chairs that you can place around the perimeter of the entire playground. Making these chairs is very easy. And here you can get by with improvised tools. In addition, in this case, you will have to use paints in order to make the chairs beautiful.

Tire frog.

All children love toys. And if your playground lacks some fairy tale, then you can furnish it with cute figurines. If you are a creative person, then you can create extraordinary beauty. We propose to make a beautiful frog, which, for sure, will attract the attention of many children.

Tire sandbox.

Most favourite hobby child is a game in the sand. And so on the playground you must have a sandbox. And it will be very easy to build. Look at several options, we hope that you will be able to find the perfect option that will also please your child.

Bike from old tires.

In this article, we list all crafts from car tires for the playground. No playground can exist without a car. Therefore, we will talk about how to make a motorbike from unnecessary tires. It's worth the effort here. You must prepare:

3 tires with discs, 5 plain tires and a pair of bicycle tires.
Sharp knife and screws.
Metal tubes.

This craft is very easy to do. Examine the photo in order not to make mistakes.

Tire snail.

To create such a snail, you should take:

a couple of tires
wood bars,
nails and screws,
brushes and paint.

And if you work a little, then you can get a unique craft that will enchant you with its attractiveness.

Finally

Now you know what crafts from old tires for the playground you can do with your own hands. We, in turn, do not advise you to throw away such products. And all because you can get real works of art, which in any case will not be left without attention.

To decorate a recreation area in the country or a playground, you don’t need a lot of money at all - everything can be done with your own hands from improvised materials. The creativity of this design will delight the kids and guests on your site.

What can you use old tires and wheels for?

Old tires from your car can get a second life, for this you need quite a bit - a little imagination and simple work. Painted crafts from wheels (as in the photo) can decorate both the playground and the place for adults to relax.

The range of tire applications is wide:

Borders and fences. A classic example of the use of tires. To make a strong and durable fence, it is enough to cut the wheels in half and install the resulting arcs around the flower beds or on the sides of the path. To add brightness and additional decor, tires are painted and decorated with ornaments.
checkerboard fence. Tires arranged in rows on top of each other in a checkerboard pattern are good Alternative option wooden and iron railings. If desired, the fence is painted and decorated with other elements. To simulate a hedge, soil is poured into the wheels and plants are planted. Over time, the fence will grow green and become a beautiful, useful and living structure.
. Flower pots on the street are irrational to use, and the beds do not have beautiful design. Therefore, creating directly in the tire is a great way out. A simple combination of wheels of different sizes, painting and decorating with ornaments will ennoble the space in front of the house or on the site. From the wheels, whole compositions of animals, equipment and utensils are created, inside of which flowers grow. Such a decoration of a summer house and a playground, made by oneself, will bring pleasure to both adults and children.
Baby swing. Simple design with the use of tires will bring a lot of pleasant time to children and adults. By fixing the tire on the turnstile or cutting it in half and fastening it to the board, you can create an inexpensive and comfortable swing.
Armchairs and tables. Such furniture will not be afraid of either cold with heat, or precipitation with drought. The solid arrangement of the tires on top of each other with a designed back and armrests can be covered with a cover or tablecloth. With a little effort, you can get a great seating area.
Bicycle parking. A convenient configuration coupled with ease of manufacture will significantly reduce the space for parking bicycles. The site will look well-groomed and stylish. To do this, the tires are cut in half and dug into the ground at the same distance in a row. If desired, the parking lot is painted and decorated.
Pet bed. Create cozy place for resting pets from a tire is easy in 2 stages: painting the tire and placing a pillow inside it. As a result, pets will be happy, and owners will not need to buy expensive furniture for animals.
. You can organize a place for playing with sand and at the same time prevent it from spilling over the entire territory with the help of a large tire. It is slightly trimmed, after which it is decorated and filled with sand. Such beauty can be used in kindergarten.
Lake or pond. Making your own with lilies, fish and other flora and fauna is easy. A large tire is dug into the ground by 1 third. The bottom is covered with polyethylene. If necessary, the tire is decorated with paint, plants or stones. At the end of the decoration, water is poured into the tire.
Stairs. The steps are alternately laid out old tires, inside of which earth or gravel was poured. Such a ladder is created quickly and, if desired, can be easily disassembled.

Crafts from plastic bottles

More available material for making crafts than plastic bottles of various sizes, difficult to find. From these secondary products create functional, diverse and beautiful decorative elements for decorating playgrounds, summer cottages and house adjoining areas.

Ideas for creating crafts from cylinders and other plastic containers:

Hanging flower pots. The bottle is cut, fixed with woven threads or ropes, giving the shape of birds, insects or simple pots. Earth is poured inside and plants are planted. The result is comfortable and beautiful hanging flower beds.
Decorative large flower beds. Everblooming and bright flowers work great with plastic. To do this, the bottles are cut in half, petals are formed. To make them curved, the plastic is heated over a candle and given the desired position. After that, the flowers are painted and installed on the territory of the site.
Furniture. A large number of identical bottles are fixed with tape or glue, gradually shaping the necessary piece of furniture. For softness, a cover with foam rubber is thrown over. Such furniture will last a long time, will please the eye and will not be afraid of adverse weather conditions.
small house. Children dream of building a hut or tree house. Such game Zone easily created from many bottles. They are fastened together with tapes, glue or electrical tape. The roof is covered with imitation tiles - rounded cut-out parts of plastic. At will, the house is decorated, furnished with interiors and curtains.
dolls and garden decorations . Bright, simple and unique toys for children are made from bottles by coloring and assembling. Plots and playgrounds are decorated with such dolls, and children can play with them with pleasure. There are countless options for dolls. Any animal fairy tale hero or appliances are easily created from ordinary plastic.
. Feeders and birdhouses are created to attract various birds and small animals. Children can observe the living creatures around them up close, and also take part in feeding them. Bottles are cut and assembled in a convenient way, leaving shelves and holes for food. If desired, crafts are painted, after which they are installed on a tree or hung from the roof.
paths. Playgrounds are easy to decorate with bright paths created from traffic jams from plastic bottles. Corks are attached to the substrate with glue, placing them in the right order and close to each other. These trails are comfortable and beautiful to use. They depict whole pictures or simply decorate with a pattern.
Curtains. Curtains from fastened parts or bottle caps will decorate any house or playground. Movable curtains are easy to play, and are made quickly and easily. Corks are pierced with a hot awl and fastened with a thread. The assembled rows are fixed on the crossbar. The order of the arrangement of elements can be any - from patterns to a full-fledged picture.
. From various parts bottles create an imitation of water, plants, animals, people and technology. Elements are painted, fastened together or dug into the ground. The result is a beautiful installation (see photo), with which children can play, and adults can admire or take pictures.
Playground. Various mechanisms are constructed from containers, with which children can simultaneously play and learn the laws of physics. An example is developing windmills and watermills, communicating vessels, weathercocks and other mechanisms.

Boulders and pebbles in decoration

With stones of various colors, shapes and sizes adjoining territory and playgrounds are transformed into real works of art. With the help of pebbles, paths are laid out, and flower beds and pools are decorated with boulders.

What to make from logs, snags and stumps?

The remaining parts of the trees are a real help in the manufacture of decor and sites. The tree is easy to process, easy to paint and deform.

Thanks to these properties, they create practical, beautiful and interesting decor elements for sites:

plywood figurines

Making various figures and figurines from plywood will bring pleasure both in the process of creation and the result of the work.

Such decorative elements perform several functions at once:

decoration;
a toy;
camouflage of flaws.

Silhouettes of the desired image are cut or cut out of plywood, painted and fastened together. As a result, they get original and bright crafts:

Other playground decoration materials

You can decorate a site for summer children's games from improvised materials, from paper and from stingrays. The main thing is that they are safe for children and easy to transform. All materials can be combined with each other, creating unique street compositions.

In addition to logs, snags, stones, stumps, plastic bottles and tires, other materials and residues are used:

Everything that a person’s imagination is capable of can be used to decorate playgrounds and house adjoining areas. Create such crafts from waste material easily at home.

home > Metallurgy