How to glue meter-long wallpapers - we understand everything and learn together! How to glue meter wallpapers: detailed instructions How to glue 1 meter wallpapers.

Recently, on the shelves of building hypermarkets and on the virtual windows of specialized online stores, you can increasingly see wide meter-long wallpapers for sale. They differ from rolls of standard sizes by almost 2 times, having a width of 1 meter, and more precisely - 106 cm.

What are their main advantages, when compared with the usual counterparts and how to choose them correctly? And most importantly - how to glue wide wallpapers? After all, throughout years many of us are accustomed to sticking standard rolls half a meter wide. So, let's move on to these interesting questions.

Detailed instructions: how to glue meter non-woven wallpaper

The process of gluing non-woven wallpaper meter wide includes several main steps. Let's dwell on each of them in more detail and find out how to glue meter-long wallpapers:

Wall prep. We remove the old wallpaper and remove the remaining irregularities in the form of paper and other residues. The advantage is the fact that the wallpaper with a non-woven base is not afraid of small surface irregularities, chips and scratches on the walls and partitions of the room. In addition, if the working prepared surface is slightly rough, this will be more of a plus before starting work.
Then it is necessary to close all windows, vents and other sources of drafts. It is recommended to close even technical ventilation openings. Moreover, it is allowed to open the vents and windows only after the glue has completely dried, which can take from 24 to 72 hours. It is also recommended to turn off the electricity for a while, dismantle the sockets, remove various fasteners from the walls: nails, screws, etc.
and wall surfaces. Be especially careful when buying glue, as it must match the type of wallpaper. The process of preparing the solution itself is not difficult and even a non-professional can easily do it with his own hands. Pour water into a previously prepared container, and gradually add dry glue, while stirring with a small stick or other improvised means. Read the instructions for the glue: it says how long the solution will harden enough and be ready to start work. As a rule, you will not have to wait more than 10-20 minutes. The field of how the glue is ready, it is necessary to mark the wall. Considering that these are non-woven, and, moreover, meter-long wallpapers, it is necessary to take into account that they will need to be glued to the joint - this will be the right way. As the reviews and advice of experts say, it is better to start gluing from the window, moving deeper into the room. As for the first sheet, align it vertically with a plumb line, and draw a line with an ordinary pencil using a long meter ruler.
The next step is cutting wallpaper for gluing. Leave 10 cm above and below as a margin. After completion of work and complete drying, you can remove excess (left in reserve) sections of wallpaper with a sharp knife prepared in advance.
We start gluing. Having successfully completed all the previous instructions, it is necessary to proceed to the next stage of work - directly to gluing. Before applying the glue itself, it is necessary to mix it again. After that, we proceed to apply the adhesive layer. This is done with a wide brush for wallpaper glue. As you know, non-woven wallpaper is not smeared with a layer of glue. It is enough just to apply it on the surface of the wall. After applying a layer of adhesive solution, gently smooth the wallpaper. This stage must be performed with high quality and conscientiously, given that you are gluing wide meter-long wallpapers. If necessary, correct the wallpaper, align it and get rid of air "bubbles" with a special plastic spatula to align the wallpaper. Smoothing can also be done with a plastic comb or roller, downward and away from the middle of the wallpaper sheet. Wipe off excess adhesive with a small sponge or cloth.
We continue to glue the rest of the cut canvases. . If necessary, you need to accurately select the pattern so that it matches the adjacent sheet of pasted wallpaper.

Advice from the masters! Since meter-long wallpapers are much wider than standard ones, it is recommended that two people stick them. Therefore, before starting work, find an assistant for yourself - it will be much easier to work with him.

Pros and cons of wallpapering meter wide

Before gluing 1-meter wallpaper, it will be useful to learn about their advantages, as well as some disadvantages. The fact is that only after a detailed study of the pros and cons of gluing wide canvases, you will have a more or less accurate idea regarding the choice in favor of one or another option.

Advantages

The advantages are definitely the following:

After the repair, fewer joints remain on the wall.
and performance of work. After all, even despite the fact that meter-long wallpapers have b about In comparison with standard analogues, the thickness is larger, anyway, it is easier to measure and stick 15 sheets than 30.
You can save additional money, since the price of one tube of wide meter wide wallpaper is, although slightly, but still lower than that of two tubes of standard width wallpaper.

Disadvantages of wide canvases

Of course, it is impossible not to mention some of the shortcomings:

Difficulties in fitting, as well as non-woven wide wallpaper to an adjacent, already pasted canvas, in contrast to traditional counterparts.
Difficulties with sticking alone. Unlike regular 53 cm wide rolls, wide rolls require an assistant.
Need better preparation wall surfaces before gluing, in order to better fit one sheet to another.

We hope that now you have more clarity on how to properly glue meter wide wallpapers. This coating, as we have seen, has a number of significant advantages. We wish you a successful renovation!

The question of how to glue non-woven wallpaper worries many who have chosen this practical and high-quality material. Its main feature is a thickened structure, thanks to which it is possible to successfully hide minor wall defects. The non-woven coating is wear-resistant, moisture-resistant, light-resistant, maintenance-free and has an original embossed surface. If you want to change the interior design, such a coating can be repeatedly painted with dispersion or acrylic dyes. The very process of pasting the walls is simple and does not take much time, you just need to familiarize yourself with some secrets of working with wallpaper.

Sticking non-woven wallpaper with your own hands has some features. To know how to glue non-woven wallpaper correctly, we advise you to familiarize yourself with the following recommendations to avoid mistakes during work:

before starting work, be sure to read the instructions from the manufacturer attached to the rolls and to the packaging adhesive mixture;
Before gluing the canvas, prepare the surface of the walls. Proceed to gluing only after the primer has completely dried;
pay close attention to gluing the first workpiece - the quality of the entire work directly depends on this;
the glued sheet should be leveled with a rubber spatula (if the surface of the wallpaper is smooth) or a wallpaper roller (if the canvas has a textured surface);
each next sheet must be glued without overlap - strictly end-to-end.
If this is not possible, for example, when gluing the canvas in the corners, use the double cut method: by laying two sheets on top of each other by 5-6 cm, you need to make an even cut with a clerical knife at the junction, then carefully remove the excess. Thus, the corners will be perfect;
the joints of the sheets (especially the corners) should be carefully ironed with a spatula or roller, removing excess glue to the side free from wallpaper;
to remove excess glue, use a damp sponge, carefully wipe the seams in the corners, do not worry about the condition of the canvas - moisture will not damage it.

The preparation and marking of the walls is an important point that should be given special attention before gluing non-woven wallpaper. You should also cut the sheets correctly and choose the appropriate composition for gluing them.

Preparatory work

Non-woven wallpaper can be pasted over any surface. If you plan to paint the wallpaper in the future, you should take care in advance that the walls have a uniform color that does not differ much from the color of the selected paint, since non-woven is thin material and the color of the base may be further noticeable.

VIDEO:

The walls should be pre-cleaned (remove the old coating) and eliminate existing defects. Then it is necessary to carefully treat the surface with a primer, it is better to apply a primer deep penetration- this will increase the adhesive ability of the adhesive. After the final drying of the primer, you can proceed to the marking of the walls. It is recommended to start pasting meter-long wallpapers from the corner - use a level to apply vertical lines to the walls at a distance of 1 m from each other, this will avoid irregularities and shortcomings in the work.

The next step is to prepare the canvas. If you have chosen a solid material, there are no problems with cutting. If you plan to glue a canvas with a pattern, make sure that it matches, for this you will have to periodically shift the next sheet up or down. Be sure to leave a margin of height of 5-7 cm when cutting - an allowance for the ceiling, cut off the excess part with a clerical knife after complete drying.

Sheet cutting must be carried out on a clean surface, rolling the roll face down. Having measured desired length blanks (taking into account the margin), make a notch, evenly bend the sheet (make sure that the edges of the lower part of the sheet coincide with the edges of the bent part) and cut it along the fold line. The next workpiece must be rolled out in the same way and before cutting, check the fit of the pattern. Further work is performed in a similar sequence.

After preparing the walls and the canvas, you can begin to solve the following question - how to glue non-woven wallpaper correctly? An important point is the choice of a suitable adhesive, the quality of the final work depends on it.

Choosing glue

For pasting walls with non-woven wallpaper, you should use a certain adhesive composition, which can be purchased at a specialized store selling building and finishing materials.

Before preparing the adhesive mixture, carefully read the instructions for the sticker process technology that is attached to the wallpaper - some manufacturers recommend applying glue not only to the walls, but also to the canvas itself.

It has a number of advantages:

does not contain toxic substances and is absolutely safe for human health;
has excellent adhesive properties, allowing the mixture to be applied to any surface;
convenient to use;
does not leave stains;
has a long shelf life in a closed container (up to 10 days).

The process of making the adhesive mixture itself is not complicated - the powder should be diluted in the amount of water indicated according to the instructions, constantly stirring until the mass thickens.

How to glue meter non-woven wallpaper

Sticking non-woven wallpaper with your own hands is not a laborious process, but if you have chosen a meter long canvas, you should take into account a few nuances. Many prefer exactly meter rolls, since this greatly facilitates the pasting process, there are fewer joints and less material consumption.

VIDEO:

How to glue non-woven wallpaper 1 meter wide? Consider the basic rules:

The main task is to carefully prepare the walls - their surface should be even and smooth. The walls should be pre-treated with putty and primer - this will level the walls and improve the ability to bond the adhesive mixture to their surface.
With improper cutting of meter-long wallpaper, you can often encounter a shortage of the length of the last sheet. In order to avoid this situation and save material, before sticking the sheets, we recommend that you pre-stick ceiling plinth to a clean wall, avoiding the need to set aside allowances (if such a finish is expected in advance).
If you are sure that the ceilings are even, it is enough to leave a 2-3 cm margin when cutting sheets. If the ceilings are uneven, you should leave more margin - up to 10 cm.
You should not start gluing meters strictly from the corner, draw an orientation line in advance, stepping back a little from the edge of the wall - this will avoid distortion of the pattern if the corners of the room are uneven.
Smoothing the canvas glued to the wall should start from the top, gradually moving towards the center and leveling the edges of the sheet.
The edges of each subsequent sheet should be applied as close as possible to the adjacent canvas, aligning the seams and tracking the pattern if you chose a non-monochrome coating.

Before starting work, be sure to study all the recommendations and prepare necessary materials- This will greatly facilitate and speed up the process.

How to glue wallpaper in hard-to-reach places

The question of how to glue non-woven wallpaper in hard-to-reach places, especially in the corners, is important. Difficult places also include areas with sockets, switches, and near batteries. When sticking the canvas near sockets and switches, you must first de-energize them and unscrew the protective boxes. Thoroughly coat the wall with glue, attach a sheet, and only after the glue has dried, make a cut required size, remove excess wallpaper and screw the boxes into place. When sticking the canvas near the batteries, carefully treat the edges of the sheet with adhesive. corners require special attention. There are two options for successful wallpapering in the corners:

BUT. If you have chosen a plain canvas, you need to stick it, starting from the corner, then glue the next sheet on the adjacent wall, grabbing part of the glued canvas, and then evenly cut both canvases with a clerical knife, removing the excess.

B. If you prefer a canvas with a pattern, the sheet is also glued from the corner, and the overlap with the next canvas should be 2-3 cm - this will hide the flaw in case of an uneven corner.

Non-woven wallpaper is a high-quality, environmentally friendly safe material used for pasting ceilings, walls in apartments, country houses, office and public spaces.

Models are produced with different textures and relief, with the possibility of coloring.

Due to the thickened structure, small surface defects can be hidden. Consider step by step instructions how to glue non-woven wallpaper with your own hands, which glue to choose, the technique of pasting hard-to-reach places.

Why non-woven wallpaper

Flizelin is environmentally friendly

Non-woven wallpaper is available in two types: consisting entirely of non-woven fabric and non-woven backing with a vinyl coating. They compare favorably with acrylic and other types due to their advantages:

produced on the basis of cell
yulose fibers, environmentally friendly;
have a beautiful textured surface that imitates plaster or has a pattern;
most often produced for painting with acrylic or water-dispersion compositions;
easy to clean, do not absorb odors;
do not support combustion.

Even a beginner can glue such wallpapers with high quality, but the technology for performing work has its own nuances that need to be studied before starting pasting.

Calculate the number of rolls

The number of rolls depends on the area of the room.

Standard sizes non-woven wallpaper: width 1.06 m, length 10 m, 12.5 m or 25 m. With a length of 10 m, the roll area is 10.6 sq. m., at 12.5 m - 13.25 sq. m., with a length of 25 m - 25.4 sq. m.

Before you go to the store, you need to calculate the area of \u200b\u200bthe room. To do this, we measure the length and height of each wall and ceiling with a construction tape, if you will paste over it. We multiply the indicators of each wall and multiply by the number of pasted surfaces.

We calculate the area of \u200b\u200bone wall and all pasted surfaces.

Room height 2.5 m, width 3 m, length 4 m.

3 m * 2.5 m * 2 walls = 15 sq. m.

4m*2.5m*2 walls=20 sqm m.

15 sq. m + 20 sq. m = 35 sq. m. (wall area).

We subtract the area of window and door openings.

Knowing the area of \u200b\u200bthe walls, you can determine the required number of rolls from the table. Table based on the size of the wallpaper in a roll: width 1.06 m, length 10 m.

Ceiling height up to 2500 mm.		Ceiling height 2500-3000 mm.
Room area, sq.m.	Number of rolls, pcs	Room area, sq.m.	Number of rolls, pcs
10	3	10	5
14	4	14	5
20	5	20	7
24	5	24	8
30	6	30	9

If the wallpaper needs to be matched, then for every 6 rolls you need to buy another roll, as there will be a lot of trimming as a result of the fit.

Adhesive selection

Choose compositions strictly for non-woven wallpaper

When choosing a glue, you must definitely look so that it says on the pack that this adhesive composition is suitable for pasting walls with non-woven wallpaper.

Consider in the table the most common types of glue for non-woven wallpaper and their characteristics:

№	Glue brand	Characteristics
1	Metylan	It is made on the basis of methylcellulose, contains additives that improve adhesion to the surface. Has antifungal protection. Resistant to temperature changes. The glue slides, so you can move the wallpaper if it is not pasted correctly.
2	Quelyd	It glides well, has antifungal protection, and is easy to apply to the surface. Has a small consumption.
3	Kleo	Produced on the basis of modified starch, includes antifungal additives. It is produced in three types: Optima, special and professional. The latter is suitable for pasting in hard-to-reach places.
4	PUFAS	It has high adhesion, transparent after drying, does not require special preparation of the walls. Available in 5 types, suitable for manual application and use in wallpaper-lubricating machines.

When choosing glue, you need to pay attention to the following indicators:

density and structure of wallpaper;
surface quality;
glue consumption.

Before pasting, the surface of the walls must be leveled, all cavities and cracks must be eliminated, since air bubbles and delaminations can form in them. It is necessary to breed, strictly adhering to the instructions.

Surface preparation

do-it-yourself begins with surface preparation.

Old wallpaper must be removed, even if it is firmly attached. When we smear the wall with glue, the old layer will begin to lag behind. In order for the wallpaper to take off well, we moisten it abundantly by wiping it over the surface with a wet cloth. We wait five minutes, pry with a spatula and remove.

Remove box from socket

We spend visual inspection walls. The surface should be free of greasy and rusty spots, which tend to show through the wallpaper.

To remove dust from the wall, wipe it with a damp cloth. All cavities and cracks are closed with putty.

We remove skirting boards, boxes from sockets, switches. To prevent glue from getting inside, seal the space with molar tape.

If the corners are crooked, it is better to invite specialists to level their surface. If this is not done, the irregularities on open space will be eye-catching.

We prime the wall with a deep penetration compound or wallpaper paste, diluted with water to a more liquid consistency than required for wallpapering.

How to dissolve glue

Make sure there are no lumps

According to the instructions on the label. Pour water into a container of sufficient volume room temperature then add the dry mix. The amount of glue should correspond to the area of the wall, taking into account the primer and pasting.

It is necessary to observe the dosage and stir well so that there are no lumps. Leave to swell for the time indicated in the instructions.

If a finished glue too thick, you can add a little water and mix.

Leave a margin of 2 - 3 cm

We measure the height of the room from floor to ceiling or decorative baguette, add 2-3 cm to the margin to compensate for uneven heights. We measure the desired length and cut off the first strip. We cut the following strips depending on whether the pattern needs to be combined. From the inside, mark the top and bottom, so as not to confuse when pasting.

If a pattern is selected, you need to number the strips in order to glue them in a certain sequence. We sign the wallpaper with a simple pencil, a thin line in the corner so that the mark does not show through on the front side.

To cut the strip evenly, you need to measure the size, bend along the mark line so that the sides coincide with each other. We draw a spatula along the fold line so that it becomes clearly visible.

Cut off the material with a spatula or sharp kitchen knife. If you cut with scissors or a utility knife, the cut line may be uneven.

Marking the wall

Can be glued from any angle

Since non-woven wallpaper is glued end-to-end, it does not matter if you start from the window or from the other end of the room, but you need from any corner.

First, you should step back a little and mark a vertical line. For proper marking, you can use a plumb line or building level.

Then we measure the width of the wallpaper and do vertical mark on the other side.

How evenly the first strip is pasted will depend on general form rooms.

Wallpapering Instructions

Consider how to properly glue non-woven wallpaper. Important rule: we cover only the surface of the wall with glue, there is no need to smear the wallpaper. Learn more about the process in this video:

In order not to get an electric shock, we turn off the electricity and insulate the wires with high quality, because the contacts in the sockets and switches are without covers.

Sticking the first strip

We apply glue with a roller or a thick wide brush with a strip slightly larger than the width of the canvas.

Wallpapering Instructions

We take the first strip by the upper end. We apply 2 cm above the baguette and align with the vertical mark. In case of incorrect gluing, lift from below and move in the right direction.

If the wallpaper lay down in a vertical line, we press them against the wall and start gluing. It is convenient to smooth non-woven wallpaper with a rubber roller or a special spatula. From the center we move up, then to the sides and down. Make sure all air bubbles come out.

Cutting wallpaper under the baguette

Immediately after pasting the strip, cut it off upper part. To mark the cut line, we draw along the wallpaper strip under the baguette with a blunt spatula. We press the wallpaper a little under the baguette and force out excess glue and air. Cut along the line with a sharp spatula or clerical knife.

In order for the wallpaper to adjoin the baguette beautifully, you need to cut along its very edge at the place where it joins the wall. The spatula should lie on the wall, and not at an angle; according to its mark, we trim with a knife.

The knife must not be torn off the surface so that jagged lines do not form on the cut line. We do not bring the knife to the end of the spatula, move the trowel forward, then continue to cut.

Excess adhesive must be removed immediately with a slightly damp, clean cloth.

Second and subsequent lanes

Attach the canvas to the glued wall

We smear the wall with glue. We apply the canvas, holding the top edge. If you need to dock the picture, move the wallpaper so that the elements match.

The canvas should lie tightly butt-to-butt with the previous strip. If glued with an overlap, then the junction will protrude, and with further painting it will be very noticeable.

We carefully monitor the tight fit of the wallpaper at the junction of the canvases. We additionally pass through this area with a roller or spatula.

Corner wrapping

The ideal option is when the corners in the apartment are even, but this is rare. If the corner is closed by furniture, you can paste it over without preliminary leveling, but if it is visible, it is better to level its surface yourself or invite a specialist.

There are two options for pasting corners:

We glue a solid strip, wrapping it on both sides. This option is only suitable if the corners are even. If the corner is curved and bumpy, the wallpaper will be stretched in some places, and folded in others. In an uneven corner, the edge of the canvas will shift from the vertical plane and lie crooked;
cut the strip, join the wallpaper in the corner. We make markings with a small margin, cut off the excess after the sticker. The wallpaper should extend about 2 cm onto the adjacent wall. The allowance will depend on how much the angle of the curve is. The greater the curvature, the greater the allowance should be. But at the same time, there should not be a large overlap, as it will be too noticeable.

Smooth out the corner

Instructions for pasting the corner:

Mark with a plumb line or building level horizontal line, which we will navigate when sticking wallpaper.
We smear the corner on the side of both walls with glue so that there are no gaps anywhere.
We paste the strip on one wall with a slight approach to the adjacent surface. Then we glue the second strip, laying it out as far as possible along the vertical line of the corner.
Then we apply a metal ruler as close to the corner as possible. With a sharp knife, cut two layers of wallpaper under the ruler at once. The top strip will fall off immediately. To remove the bottom strip, bend the top canvas. Then we coat the joint with glue and press down the wrapped edge.

After the wallpaper dries, we cut holes in them for sockets, switches. Install body panels. We turn on the electricity.

Pasting the area behind the battery

The most difficult thing is to paste over the wall behind the radiator. This work is always left in the end, they start it after pasting the remaining surfaces in the room. See this video for more details:

You can paste wallpaper by removing the battery

There are two ways to paste:

dismantle the battery by installing plugs on the walls. For such work, you will have to invite an experienced plumber. After the battery is removed, the wall needs to be primed. When the primer dries, we paste over the niche with wallpaper. It is desirable that the joint is located in the center of the radiator, then it will be invisible. We cut the top of the canvas under the windowsill according to the same principle as under the baguette. We install the battery in place;
glue the surface without removing the radiator. This will require patience and skill.

Instructions for pasting non-woven wallpaper area under the radiator:

Cut the strips to the size of the desired area.
We make vertical cuts at the locations of the fasteners.
We smear the wall with glue so that it leaks over the battery. Highly thin layer you can smear a strip of wallpaper.
We start the canvas by the battery, smooth it with a rag. To get hard-to-reach places, you can wrap a rag on a stick and smooth the wallpaper behind the battery.

If these manipulations are too complicated, you can paint the surface under the battery, stick a heat-reflecting material, or decorate it with a special perforated panel.

Nowadays, meter-long non-woven wallpapers are gaining relevance every year. This is not surprising, since it will turn out to stick such wallpapers at least 2 times faster than the material of standard footage. For gluing such wallpaper, no special skills are required. It is important to align the concrete walls very well, otherwise the joints will be uneven. As soon as the walls are leveled, it is necessary to wait until the putty dries, it is necessary to prime, after that paste the wallpaper.

After the wall is prepared according to the rules, it is necessary to apply pre-prepared glue on it.

The advantages of this type finishing material obvious:

Gluing takes little time;
There is not much waste left;
After work, the joints are less.

All this cannot but affect the quality of work and appearance. But, despite the advantages of wide non-woven wallpaper, there are still suspicious people who buy ordinary wallpaper, believing that sticking them will turn out without problems, faster and better. In fact, working with non-woven wallpaper is quite simple. The main thing is to properly prepare the walls and glue it with your own hands, it will turn out flawlessly.

It is important to remember that a special glue is used for this type of wallpaper, which can be purchased at a specialized store.

Once the adhesive has been applied, follow these steps:

Take a canvas of wallpaper, adjust it in height.
Start gluing the canvas along the broken line on the wall surface.
We turn the second side of the canvas at an angle.
Immediately start smoothing the wallpaper from top to bottom, expelling air bubbles.

For smoothing, tools such as a rubber spatula, a wallpaper roller, or a clean cut are well suited. thick fabric. As soon as smoothing is completed, it is necessary to cut off the excess wallpaper residues at the ceiling and at the bottom plinth. It is convenient to cut off with a sharp clerical knife, and use a metal spatula as a guide. If wet wallpaper does not cut well, you can wait until the material dries.

For those who first decided to glue wallpaper on their own, we advise you to read the following material:

Self-gluing non-woven wallpaper end-to-end

Pasting using butt technology will be fully completed if the walls have been carefully aligned. When the walls are perfectly even, the non-woven fabric is glued end-to-end to the second glued canvas, without overlap.

The butt bonding process is carried out as follows:

A special adhesive is applied to the wall.
The canvas is glued end-to-end in height.
As soon as the joint is made, it is urgent to expel the air.
It is forbidden to achieve a joint by stretching the canvas, when the wallpaper is dry, there will be gaps between the canvases.
Excess at the ceiling and floor is cut off with a clerical knife.

Masters recommend using one little trick. If it is not possible to glue end-to-end, then you can overlap it by about 3-4 cm, and after the wallpaper has dried, use a sharp clerical knife to make a through cut in the place where the canvases intersect. In this case, both canvases are cut at once. After the cut is made, the trimmings must be removed, the joint should be greased with glue, and the canvases should be straightened, as a result, an even, neat joint will be obtained.

Much more useful tips to achieve perfect result in wallpapering:

How to glue non-woven wallpaper in the corners of the room

The first method is used when wallpapering a room with a pattern is in progress.

This method involves gluing the canvas strictly from the corner with an overlap on the previous canvas of 2-3 cm. This method allows you to hide flaws in the case of a crooked corner. The second method is ideal for non-woven wallpaper of one tone, material without a pattern.

Step-by-step execution methodology

The canvas is glued from the corner.
Both canvases are cut with a clerical knife.
Surplus is removed.
The joint is coated with glue.
The fabrics are neatly aligned.

This technique cannot be used when gluing wallpaper with a pattern, as the structure of the pattern will be disturbed during cutting. It is also important to properly smear the glue, it should not be neither more nor less, just enough so that the canvases can be bonded to the wall. On the concrete wall and an equal amount of glue is applied to the drywall, and the composition is not applied to the canvas at all. As you can see, sticking wide wallpapers is very simple, a little time, patience and the result will impress you. At the very least, gluing non-woven fabrics is much easier and faster than ordinary narrow wallpaper.

Is it possible to glue non-woven wallpaper on old wallpaper: tips from the master

If a person bought non-woven wallpaper and plans to carry out repairs with his own hands, then he will be interested to know a few nuances, for example, information on which surface it is possible and better to glue the finishing material on.

Non-woven wallpaper can be glued on different surfaces, among which:

Porous concrete;
Plaster;
Drywall, etc.

Glue non-woven wallpaper on the paint should not be, as they peel off, it is also impossible to glue the canvas on old wallpaper. Masters say that old paper wallpapers have a feature of bubbling after re-pasting, which will not have a positive effect on the result of the work. Why it is impossible to paste on old wallpaper and paint is understandable, therefore, the most the best option is the removal of the old coating, the preparation of the wall and pasting with good, high-quality non-woven wallpaper. When sticking this type of wallpaper, you should exclude the possibility of a draft, in addition, turn off the air conditioner, and start gluing from a window or corner.

Is it possible to stick wallpaper on non-woven wallpaper: expert advice

As mentioned above, glue non-woven wallpaper on old surface Not recommended. The result may not please. Interior decorators recommend working with a pre-cleaned and prepared wall.

Masters like to work with this material, and they note the following advantages of non-woven wallpaper:

Long service life.
The canvas does not stretch, does not dry out, does not deform.
Easy to stick on, easy to remove.
The canvas has a different relief and pattern, which makes it possible to play with the design of the room.
Wallpaper increases sound insulation.
Improve fire resistance.
The fabric is breathable.
Environmentally friendly composition.

To make repairs easy, experts recommend that before starting work, you will familiarize yourself with the rules, which describe in detail what you should pay attention to and what you should not do. Knowing the rules, everyone will succeed in gluing correctly; in this case, special skills are not required.

Home master: rules for gluing non-woven wallpaper

Before unpacking the wallpaper, check for defects. Further, experts recommend studying the icons and their description located on the wallpaper. Carefully read the rules for preparing the walls. If you plan to stick thin non-woven wallpaper, then you need to prepare the surface in the same way as when sticking vinyl wallpaper and thin paper wallpaper. Next, you need to correctly calculate the amount of material used. When cutting canvases, it is necessary to observe the technique, then it will be possible to avoid high consumption. Glue must be bought specifically for non-woven wallpaper, and before breeding it, you should carefully read the instructions. The glue is applied not to the canvas, but to the wall, we must not forget about this nuance.

When working, use only quality tool, a wallpaper spatula which:

Smooth out the wallpaper;
Remove excess air
Remove excess glue.

It is necessary to work only during the daytime, when you can not turn on the light, this will avoid electric shocks while pasting wallpaper near sockets. Cold air currents should also be avoided. For the device of the curb it is necessary to use special glue. If the canvas is smooth, then you can glue the border already on the glued canvas, but if it is embossed, then you should first stick the border, and then start pasting the room.

A metal ruler and a sharp knife are perfect for trimming.

The room should be warm and dry, optimum temperature indoors 22 degrees. In order to glue the place around the outlet, it is necessary to turn off the electricity, remove the outlet, stick the canvas, cut out a cross inside and cut off the corners. It is necessary to work with glue as carefully as possible, you should not smear a lot of glue, you should also avoid getting glue on the front side of the wallpaper. It is better to glue end-to-end, because when gluing with an overlap, the result will be terrifying, the wallpaper is very dense. You need to glue it very quickly, as the glue dries quickly.

How to glue non-woven wallpaper (video)

Instruction

Wide wallpapers, undoubtedly, have enough advantages over the usual thin types. So, meter-long wallpaper simplifies pasting work, reduces the number of seams that often spoil the overall appearance of the room, and also reduces the cost of acquiring such material for wall decoration, since one meter-long wallpaper roll costs a little lower than two similar small ones.

Prepare wallpaper, special glue for non-woven wallpaper, building water level, pencil, tape measure, glue roller and bucket, plastic spatula, soft-bristled brush, knife, polyethylene film and a roller for rolling the edge.

Prepare the room. To do this, you must completely remove the previous coating, align the walls if necessary, remove all sockets and switches, insulate the wires. Mark the room. Marking should be started from the corner of the room, as there will be overlapping wallpaper pasted over. Set aside one meter on both sides of the corner and make a vertical mark with a pencil and a level, approximately the height of your height. Make these marks every 1.06 m (width of the tube), marking the exact distance with a tape measure.

Spread the film on the floor of the room so that the wallpaper does not get dirty and glue does not get on the floor. Determine the height of the wall by measuring it with a tape measure. Roll the tube over the film face down. Mark your length (wall height) + 10 cm.

Bend the roll and return with it to the starting point so that, by cutting off the length, you end up with two strips of wallpaper. Run your finger along the fold, making it more even and precise.

Cut the folds with a prepared, well-sharpened knife. Prepare, thus, strips of wallpaper for the entire room.

Dilute wallpaper paste according to the instructions and let it stand in a bucket until it swells completely. Dip the roller into the glue and spread the area for the first panel (the first strip) on the wall. Take the first strip of wallpaper and attach it to the wall. It is important to know that pasting the strip starts from above (from the ceiling) and stretches downwards.

Take a brush and smooth the panel along the entire length from the middle to the edges. Do the same with a plastic spatula. The canvas should fit snugly against the wall and not have bubbles. Cut off the stock that turned out at the floor, if there is one. When doing this, consider the width of the plinth, which will be subsequently fixed.

Glue the second strip in the same way. When pasting a corner, the wall should be abundantly smeared with glue. Here, two strips of wallpaper are placed on top of each other, that is, there is an overlapping pasting. In this case, the wallpaper is tightly pressed with a spatula and the corner is cut, after which the seams are evenly joined. Take the roller and roll it gently over the seams. Carry out the same actions with other canvases, joining them with each other along the marked lines.