Alpine hill with dwarf pine. The choice of conifers for the alpine slide

Alpine slides always attract attention with their beauty and unusual design. They not only complement landscape ideas, but also able to set the tone for the entire garden, and the quantity original solutions will help in the organization of individual projects that can satisfy the most demanding taste.

Alpine slide design and decoration

Having decided to make an alpine slide in your own summer cottage, you first need to decide how it should look. The most popular today are:

Alpine slide with a waterfall;
Alpine hill with a pond;
Alpine hill of conifers.

Deciding to create Alpine slide with a waterfall, you need to prepare the following components:

hoses;
Pump (high efficiency);
sealant;
Geotextile.

You can make an alpine slide with a waterfall yourself, it is only important to know a few basic steps:

Water should be brought to the top of the slide. This will require hoses;
Having finished working with hoses, they must be decorated with stones of different sizes;
The reservoir should be located below:
- Dig a pit;
- Place sand at the bottom, coarse is better;
- Lay geotextile on top;
- Put another layer of sand;
- The next layer is pebbles;
- Next are the big rocks.
When the work is completed, the resulting container must be filled with water;
Connect the pump;
Start system.

When arranging such an alpine slide, it is important to pay attention to the fact that the soil must have a special composition: ½ part of peat and ½ part of garden soil.

To organize an alpine slide with a pond, you will need:

Film (black);
Sand;
Large stones or cobblestones;
Stones for decor.

The sequence of actions for the device of such a slide is as follows:

First you need to dig a small pit;
Remove tree roots and other debris from the pit;
Next, you need to make special recesses around the entire perimeter of the pit;
Lay a black film on the bottom and decorate the perimeter with stones. For this, recesses are needed;
Soil is poured over the film, on which cobblestones will be laid;
Fill the pond with water.

Having decided to make a rock garden from conifers, it is important to know that such a design should look like it was created by nature itself, and you did not put your hands on it. For this reason, conifers are the most suitable plants. Alpine hill for some part consists of stones and cobblestones, and coniferous plants grow well in such conditions in natural nature. Best suited:

Fir subalpine;
Cossack junipers;
Pea-bearing cypresses;
Mountain pines;
Cedar salad bowls.

How to make an alpine slide?

The arrangement of alpine slides is not too complicated and such an object landscape design it is quite possible to do it yourself. You just need to know the sequence of actions. Below is an example of a classic alpine slide with several tiers of stones:

The first tier must be executed in the form English letter"V". At the bottom of each tier, large stones should be laid, which will play the role of key ones and prevent small pebbles from sliding and sliding down the slope. Each large stone around is sprinkled with earth so that it is more tightly fixed. After the completion of the device of the 1st tier, a part of the plants is planted;
 Each next tier is made in the same way - a little soil is added, leveled, stones are laid and plants are planted;

In order to properly compose an alpine slide, on each subsequent tier it is necessary to lay stones slightly smaller than on the previous one.

The top should be shaped like a pyramid. For this, stones are used small size, fix as close as possible to each other using the ground;
Then the entire hill needs to be sprinkled with soil a little more to provide additional fixation;
Then you can start planting the remaining trees. For this, it is better to choose coniferous creeping plants. various forms and shades.

The work may seem simple enough, but first you will need to compile detailed diagram future design, as well as a plan for its device. If you are worried that you may not be able to do everything right, then it is better to contact a landscape design specialist.

When developing a scheme on your own, you need to remember that such structures can be arranged at various heights - from 1 to 3 meters. And when digging a foundation pit, it is important to consider that its height should not be less than 30 cm, since in the end it will shrink a little (about ¼ of its own height), which should not spoil the composition.

Alpine slide scheme includes:

Black pine;
Juniper "Gold Star";
Thuya "Teddy";
Barberry thunberg;
Five-leaf girlish grape;
Buzulnik toothed;
Plantain "Rubra";
Thyme;
styloid phlox;
Sheep.

Alpine hills, photo gallery

By entrusting the work to professionals, you can get very beautiful design solutions. Here are some of them:

Alpine slides:

In the photo, the second stage is the installation of stones and backfilling with fertile soil
Mini alpine slides:
Rockeries and alpine slides:

Video

Decor such as an alpine slide requires not just an idea, but the ability to combine plants and their colors. If you don’t want to experiment, refer to the video instructions for building a beautiful alpine slide:

Alpine slide is perhaps the best component of landscape design. Such a decision will not only please the owners suburban area, but also their guests, and the quiet murmur of water will bring peace and a sense of satisfaction.

Alpine slides for many years have been an integral attribute of almost any suburban area. And even if you have a small area of land, there will definitely be a corner for an alpine slide. It will be easiest to invite a professional landscape designer, but at the same time, creating a site design with your own hands is very exciting and interesting.

Since the alpine hill is a mountain landscape in miniature, then the plants should be selected appropriately, conifers will look especially good.

The first thing to do is to study the characteristics of conifers, their varieties, and select those that fit your criteria, that is, the height of the tree, the color of the needles, and the intensity of growth. Remember that in the background the slides will grow more tall perennials that require more moisture. So you need to think about watering them in advance.

The most suitable plants for alpine slides are low and slow growing trees: various conifers, spirea, cinquefoil, juniper, spruce, fir, pine, thuja. Herbaceous perennials are also good, which grow into a beautiful thick carpet. Among them can be both flowering and decorative species.

Since almost all the plants that are planted in an alpine hill are perennials, they all grow with different speed, but rather slowly. In this case, it is best to dilute the planting of perennials with annuals, so that the height and density of plants can equalize in the first year and a half.

But be careful with your choice. annual plants- many of them produce a lot of self-seeding seeds, which in the future can create difficulties in the form of weeds you do not need. Such plants are well suited: undersized marigolds, gazania, sea lobularia. Before planting, carefully study the care and needs of plants so that they coincide with the main perennials.

Marigolds are undersized

Also, in addition to perennial and annual plants, stones and boulders are used to create a slide. different sizes, which are laid out according to the intended composition. Therefore, all plants are planted at a small distance from each other - somewhere around 20-30cm. Those places where there are no stones are usually covered with fine gravel.

If you have a small, rocky area (about 6 square meters), then the height of the plants for the slide should not be more than 50-70cm. For large plots with an area of more than 30 sq.m. - the height of the crown can reach more than one and a half meters. Therefore, as we said earlier, you need to know in advance about such things as the growth of an adult tree in order to harmoniously combine all the plants on the alpine hill with each other.

Now we will analyze the features of some coniferous plants, the height of which in its final form does not exceed one and a half meters.

dwarf species mountain pine:

"Winter gold" - crown shape - shrubby, spherical; the height of an adult plant is 0.5 m; diameter - 1.0 m; the color of the needles - in summer - bright green, in winter - golden yellow. Frost resistant variety.

"Mughus" - crown shape - shrubby, spreading, sometimes creeping; height of an adult plant - 1.5 m; diameter - 0.6 m; the color of the needles is dark green.

"Gnom" - crown shape - shrubby, dense, spherical; height of an adult plant - 1.5 m; diameter - 1.5 m; the color of the needles is dark green.

"Mors" - crown shape - shrubby, spherical; the height of an adult plant is 0.5 m; diameter - 0.5 m; the color of the needles is greenish-blue.

Dwarf pine Winter gold

Dwarf species of juniper:

Chinese juniper - crown shape - semicircular; height - 0.7 m; diameter - up to 1.0 m; the color of the needles is green or bluish-gray.

Juniper scaly - crown shape - cushion-shaped, compact; height - 0.5 - 0.1 m; diameter - 1.5 m; the color of the needles is bright, silver-blue. Frost resistant variety.

Common juniper - crown shape - creeping; height - 0.2 - 0.3 m; diameter - 1.0 m; the color of the needles is green. Frost resistant variety.

Juniper Cossack - crown shape - pillow-shaped; height - 0.5 - 0.8 m; diameter - 1.5 m; the color of the needles is dark green or bluish-green. Frost resistant variety.

Lying juniper - crown shape - semi-creeping, dense; height of an adult plant - 1.0 m; diameter - up to 2.5 m; the color of the needles is green or bluish-gray.

juniper chinensis

Dwarf types of thuja:

"Hoseri" - crown shape - spherical; the height of an adult plant is 0.5 m; diameter - 0.6 m; the color of the needles is dark green. Frost resistant variety.

"Little Dorrit" - crown shape - spherical; height of an adult plant - 0.8 m; diameter - 0.6 m; the color of the needles is dark green. Frost resistant variety.

"Danica" - crown shape - spherical; height of an adult plant - 0.8 m; diameter - 0.8 m; the color of the needles is dark green.

Thuja Hoseri

Dwarf species of spruce:

"Little Gem" - crown shape - spherical-flattened; the height of an adult plant is 0.5 m; diameter - 0.5 - 0.7 m; the color of the needles is light green.

"Nidiformis" - crown shape - nest-like, with a deepened middle; height of an adult plant - 0.5 - 1.0 m; diameter - 0.8 - 2.0 m; the color of the needles is dark green.

"Will's Zwerg" - crown shape - narrow conical, dense; height of an adult plant - 1.0 - 1.2 m; diameter - 0.4 m; the color of the needles - young - pale green, old - dark green.

"Echiniformis" - crown shape - cushion-shaped, compact; height - 0.2 - 0.6 m; diameter - 0.4 - 0.8 m; the color of the needles is green.

Norway spruce Little Gem

Finally, we would like to say that the most milestone in creating an alpine slide is its planning. After all, you will have to familiarize yourself with big amount material for many plants before you can select the ones you need. So take your time, think everything over, and think big, presenting a finished composition when your trees are 2-3 years old. And only after approving each plant, get to work. I wish you success!

Rock gardens cannot be imagined without conifers, but some gardeners go further and create compositions entirely consisting of conifers. The desire to use them is understandable - coniferous trees for an alpine slide are simply ideal, they are decorative, unpretentious, and retain an attractive appearance. all year round and allow you to create a spectacular corner in the garden, even if there is not too much time to care for the plantings. The main thing is to observe the naturalness and imitation of the natural mountain landscape.

Features of the construction of an alpine hill from coniferous plants

The advantages of an alpine hill from conifers include the fact that you do not need to select plants according to the timing of flowering and you can almost immediately make the hill the way you intended. Minus - coniferous seedlings are not cheap. A compromise option is to plant young plants, hoping that they will grow, but for now, decorate voids with stones or ceramic elements.

When planting conifers, you need to remember that they need space

Choosing a place, taking into account the conditions necessary for conifers

In all the photos of the alpine hill from the conifers, it can be seen that it looks impressive if you choose a place that is viewed from different sides, preferably sunny. Some types of spruces, pines and arborvitae tolerate shading well, but junipers will suffer from a lack of light. Plants with colored needles must be in the sun. When creating an alpine hill from conifers in the country, it should be borne in mind that most of these plants:

photophilous;
need space for normal development;
usually grow well on sandy-clay or even stony soils;
unpretentious, but do not like high level ground water.

Unpretentious thuja will decorate any rock garden

Creating drainage and forming a slide

Since coniferous trees for the alpine slide do not like excess moisture be sure to do drainage. To do this, remove upper layer soil and cover the hill with crushed stone, pebbles, small construction waste. The height of the drainage is from 10 to 20 cm. The soil layer is poured on top and the laying of stones begins. The stones are laid parallel throughout the hill. First, choose a place for larger ones, then put small ones.

So that the hill does not warp, there should not be cases when the stone lies on the lower cobblestone with one end, and presses on the soil with the other. Coniferous trees and shrubs have developed large roots, so pits are made between stones for their planting. The voids are filled with soil. After the construction of the hill, you need to let the soil settle, so it is better to start planting after a while. Ideal option: in the fall - to build, and in the spring - to plant.

Combine different types hvoynikov - real art

What types of conifers are suitable for rock garden

For coniferous rock garden fit trees and shrubs small sizes or dwarf species. Creeping varieties must be present. Combination different shapes crowns and coloring needles creates interesting solutions. There is a green, bluish and yellowish shade of needles. Some are bright yellow in color.

Miniature cypress ideal for landscape compositions

Names and photos of the most suitable species

For middle lane from conifers for an alpine slide it is worth choosing:

thuja - plants with a dense crown, which tolerates a haircut well. Most of the varieties common in Russia come from the western thuja: Danica with light spherical crown, Filiformis resembling a cone, Golden Globe with yellow needles. Thuja propagates by cuttings, but it is better for inexperienced gardeners to buy a ready-made seedling;
cypress trees - fashion idea for rock garden from Europe (hedges from this plant are popular in Britain). Not all varieties are hardy. The easiest way to grow Lawson's cypress and pea. It is better to overwinter low plants that can hide under the snow. Cypress trees love to spray, but the water should not be icy;
ate - a lot was bred undersized varieties: dwarf - up to 1.5 m, mini-varieties - up to 1 m, micro-specimens - up to 30 cm. For example, the Alberta Globe variety with a crown resembling a ball squeezed from above grows by 50 cm in 10 years. Nidiformis spruce is very beautiful with silvery needles. Attractive varieties canadian spruce with small gray needles and a pyramidal crown;
pines of all kinds are valued by gardeners. Dwarf and slow-growing varieties have been developed. Fluffy bushes of Scots pine Watereri or mountain pine Cobold with emerald needles fit perfectly into the landscape of rock gardens. The slow-growing dwarf Globosa Viridis reaches a height of only one meter and is suitable for small garden;
junipers of all kinds. Pyramidal plants are planted both singly and in small groups, creeping ones are arranged so that they have room to grow. They cover the ground and contrast with more high grades. In winter, many junipers need shelter with spruce branches.

Juniper Dahurian

Coniferous plants for the alpine slide, the photos and names of which were given above, are suitable if you take specially bred dwarf varieties. To prevent them from growing, you need to pinch new sprouts and pruning in a timely manner. Fertilizers should not be abused. It is also undesirable to allow animals to "mark" the trunks of "babies". If this happens, rinse the affected area with water.

Today it is difficult to imagine a modern garden without an alpine slide. It is the alpine slide (or its other name - the rock garden) that gives the garden originality, completeness, and, where necessary, the feeling of a changed landscape. All this is due to successful combination ornamental plants, flowers, trees and stones.

At the first stage of creating an alpine slide, the location and possible decor should be determined. Next you will need stone boulders various sizes and forms of your choice.

Also, to change the level of the slide, drainage should be prepared, which lies in the very center. Can be used as a drain special materials, and ordinary fallen leaves and small twigs. From above, the drainage is covered with soil and decorated with boulders and stones in the way you like best.

The main thing, do not forget: both the earth and the drainage will settle, so the height of the alpine slide itself will become lower than it was when laying.

After the slide is ready, the process of its "settlement" begins. Here your imagination should not be limited to absolutely nothing. The richness of the flora today has reached its climax, so you will not have any difficulties with choosing plants for the slide.

A good addition to the alpine slide can be paths paved with flat stones, plaster sculptures and the like. However, if you planned to arrange in an alpine slide or a small waterfall resembling a miniature natural mountain river, then you cannot do without expert advice.

Moreover, you should follow the advice during the planning of the slide, and not after its completion, otherwise you will have to destroy part of your own work. Of course, if you created a slide a long time ago, and now you decide to supplement it with bubbling water, this is another matter.

In order for the alpine slide to fulfill its purpose, it must be built taking into account certain rules. Not every plant is suitable for a rock garden, so careful selection is necessary, taking into account the timing of flowering plants, the possibility or inadmissibility of a joint neighborhood, the duration of flowering, and many other factors.

If all the landing conditions are met correctly, then the alpine slide will delight with beautiful and luxurious flowering all summer, and possibly autumn.

For this to happen, it is necessary for planting a slide to choose those plants that begin to bloom alternately. Thanks to this, the rock garden will constantly change and have a picturesque and well-groomed appearance.

To create alpine slides, for the most part, undersized plants are chosen. These are, for example, cinquefoil, salvia, low-growing varieties of nasturtium, spirea, daisies, primroses and many others.

In addition, slowly growing tree-like or, again, undersized coniferous specimens are planted on the hill, but a couple of them are added to create accents. large plants or shrubs.

In order for the alpine slide to become a decoration of the garden not only in summer, but also in winter, among the plants should appear coniferous species. Juniper and dwarf pine are well suited for this.

In addition to ornamental plants, you can plant on an alpine hill medicinal herbs, then she will also become a house doctor. For this, thyme, rosemary, chamomile, sage and other similar plants are very well suited.

In addition, before landing, it is necessary to take into account the cardinal directions. This is done so that all types of plants can take root well and gain strength, since some of them, due to the fact that they need a significant amount sunlight, prefer to grow only on the south side.

Unpretentious or shade-loving plants grow well in the northern parts of the rock garden. And flowers such as bluebells, crocuses and chrysanthemums do well everywhere.

Thus, if you make very little effort and follow all of the above recommendations, you can create a real creation in your garden.

What plants are needed for rock garden?

Constructing a rock garden on the territory on their own, it is very important to know how to correctly and successfully choose plants that will not only look great, but also long time enjoy your bloom. Plantings should be not only diverse, but also well adapted to the climatic conditions of the suburban area.

When choosing plants for, one should not deprive attention of carpet and undersized plantings, which will become the basis and background of the finished rock garden.

When choosing green spaces, be sure to take into account the weather and climatic conditions to which the site where the alpine slide will be located is exposed. Plants should have enough sunlight, moisture, heat and fertilizer.

It is also very important to pay attention to the intensity of growth and branching of plantings, as this can spoil the appearance and flowering of the alpine hill. Plantings should harmonize with each other in size, color, growth rate, flowering time.

Since the rock garden is being built on long term, plants should be selected as annuals and perennials. First of all, you need to take care of planting ground cover plants that will help to densely cover the surface of the earth.

Landscape designers recommend that when choosing plants for a rock garden, take into account the size and color of boulders that will form the basis of a decorative object. In order for the rock garden to look harmonious and not overloaded, the stones should be laid asymmetrically and loosely. You can fill the bare gaps between them with undersized plantings.

In addition, plants should be planted in tiers, the top should be the tallest and most lush species, while with each subsequent circle, the height and size of the plantations should be reduced. In order for the rock garden to function all year round, the hill can be decorated with coniferous and evergreen plantings.

Perennial plants for alpine hills - photos and names

In order to make it easier to choose plants for an alpine slide, we present you the most popular ones with names in two languages and photos.

Anemone - Anemone

Alyssum rocky - Alyssum-saxsatile

Alyssum white

Badan – Bergenia

Periwinkle herbaceous - Vinca-herbacea

Marigolds – Tagetes

White Perfection - Musky Malva - Malva moschata

Cornflower mountain - Centaurea montana

Veronica - Veronica

Monetary loosestrife - Lysimachia nummularia

Carnation - Dianthus

Carnation stunted

Geranium - Geranium

loosestrife - Lythrum salicaria

Dicentra - Dicentra

Tenacious - Ajuga

tenacious creeping

St. John's wort - Hypericum

Iris - Iris

Round-leaved saxifrage - Saxifraga rotundifolia

Kotovnik - Nepeta

Lavender narrow-leaved - Lavandula angustifolia

Potentilla - Potentilla

Potentilla Nepalese -Potentilla nepalensis

Lupine - Lupinus

Rejuvenated - Sempervivum

Euphorbia - Euphorbia

Euphorbia bordered (bride)

Peony - Paeonia

Purslane garden - Portulaca oleracea

Multi-colored purslane on an alpine hill

Primula - Primula

Rudbeckia - Rudbeckia

Sedum - Sedum

Amethyst eryngium -Eryngium amethystinum

Amethyst eryngium

Sleep Grass - Pulsatilla

sleep-grass

Yarrow - Achillea

Thyme - Thymus

Violet - Viola

Phlox subulate - Phlox subulata

Phlox subulate

Chistets - Stachys byzantina

Oenothera Missouri - Oenothera missouriensis

Jaskolka - Cerastium

Yaskolka

Many owners of personal plots know how important it is to keep their territory in order and clean. Everyone tries to bring a little bright colors and greenery that will transform a modest landscape design.

An excellent decorative object is an alpine hill, which is a heap of stones and plants that can become a real pride and decoration of any site.

What is an alpine slide and what plants are suitable for it - expert opinion

Read about everything here.

An alpine hill is called an artificial or natural mound of earth, a hill where evergreens grow, herbaceous plants and shrubs are decorated with stone elements.

This element of garden design got its name due to the fact that it is planted here. alpine plants, which in their natural state grow in mountainous and foothill areas.
Read a detailed illustrated article on how to make an alpine slide with your own hands.

To learn how to make a palm tree from plastic bottles, read .

Basic rules for plant selection

A flower garden with a rocky garden is increasingly common on modern garden plots. It is not difficult to create an alpine hill or rock garden, it is enough to know the main plants that can be planted on a hill, as well as the principles of their placement.

In addition, the rock garden is easy to care for. The stone composition looks beautiful and original if you add several types of alpine plants to it.

We offer you the basic rules for selecting plants to create a decorative rock garden:

1. When creating a composition, it is worth Special attention give undersized plants. It is important that in size they correspond to the size of the slide, look harmonious.

2. Choose plants that will tolerate the local climate well. If the slide will be created on sunny area, then light-loving plants should be planted, and vice versa.

3. The intensity of tillering and growth of green spaces should also be taken into account. If you plant plants that grow well, close to undersized ones, small plants who love the light, then you will deprive them of the opportunity to grow and please the eye. For example, beautiful and unpretentious soapwort, yaskolka, obrietta, rezuha will negatively affect plants in the neighborhood.

4. Plants on the hill should be combined with each other in appearance, growing conditions, rates of development and growth, according to the flowering period.

Types of plants to create an alpine slide

Alpine slide is created on long time. When choosing plants for an alpine slide, give preference to cinquefoil, spirea, conifers, which grow rather slowly, but create a dense layer.

Tall herbaceous and woody plants look best next to large stones, and experienced gardeners it is advised to avoid symmetry when planting such plants.

To avoid gaps between perennials, which at first will not be able to fill the entire space of the rock garden, such places should be planted with annual flowering plants: gazania, large-flowered purslane, marigolds, gypsophila, marine lobularia and others. These plants love the sun and are unpretentious to the constant receipt of moisture, so they will fit perfectly into general form slides.

A properly created alpine slide will turn any site into a small natural wonder.

Each gardener must answer for himself the question: in what colors does he want to see an alpine hill? It is also important to create a slide plan on paper - schematically draw the shape of the slide, mark the location of the stones in the figure, and also paint over the rock garden sections with different colors to see the whole picture.

Dwarf coniferous plants look beautiful on the alpine hill, which will favorably highlight your hill all year round. Popular dwarf spruces can have several shades and favorably emphasize the element of landscape design. The same group includes juniper - an unpretentious plant in care, cypress - a coniferous plant with a golden top, as well as thuja.

Giving preference to deciduous plants on an alpine hill, exclude species with falling leaves, which will only spoil the overall look. Among the evergreens deciduous plants for an alpine slide, iberis is often used - a plant with white, purple or pink flowers in umbellate brushes.

The dryad looks beautiful due to white catchy flowers, as well as horizontal cotoneaster, which begins to blush in autumn and stands out favorably among other inhabitants of the alpine hill.

To make the alpine hill look harmonious and beautiful, it is worth planting shrubs and conifers one at a time, and filling the gaps between them with undersized plants.

Between the stones, along with coniferous plants, carpet plants should be planted, which in a few years will braid the hill with a beautiful canvas. These include rocky beetroot, which is distinguished by gray-green leaves that retain their color all year round. Burachok blooms with small bright yellow flowers in panicle inflorescences.

You can give preference to a short-stemmed carnation, which blooms richly with bright beautiful flowers. Saxifrageforming dense rosettes from their rosettes beautiful pillows, are a mandatory attribute of the alpine slide. Different kinds saxifrages can bloom both in the shade and in the sun.

If you want your rock garden already in early spring began to please the eye, and until late autumn retained color, tuber-bulbous and bulbous plants.

Early color will provide blueberries, snowdrops, chionodoxes. But until late autumn, their flowering will please the eye autumn crocuses, late tulips, avian, colchicum.

The Alpine hill will be perfectly complemented by a small "mountain" waterfall

The principle of tiered planting

To make the alpine slide a real decoration of your garden, you should follow the rules for planting plants, depending on the tiers. So, let's start with the top tier.

top of the hill

The top of your garden decoration is more open to the sun's rays, so it is advisable to place light-loving plants here. In addition, there is practically no moisture left at the top, so the top of the rock garden should be framed by plants that require the least moisture.

To ensure that the top of the alpine hill blooms all year round, choose ground cover plants that will bloom one after another. Browse through various plants for an alpine slide, photos and names of which will help you make your choice.

For example, in May-June, the top of the hill will be covered with fluffy iberis, and throughout the summer and autumn, the upper tier will delight you with flowering cushion-like bushes. perennial carnation that lives in mountainous areas.

If you want butterflies and bees to always hover over the top of the rock garden, you should plant plants with a pleasant honey aroma, for example, creeping thyme, which forms a carpet on the surface.

Alpine edelweiss is one of the main elements of the top of the hill. This plant loves the sun very much, and in natural environment lives on rocky slopes high mountains, however, for excellent plant growth, it will be necessary to prepare the soil mixture.

If you want to grow on top of an alpine hill undemanding plants, then the best choice will be young.

We form the middle tier

In the middle of the hill should be plants that love the sun, but at the same time tolerate the shade well. In this place of the hill, the soil is more humid, so there will be a lot of variations for planting.

To ensure lush flowering in May, plant styloid phlox, blooming in blue, pink and white flowers. As a background plant for such bright colors three-vein anfalis, woolly chistets, Schmidt's wormwood can act.

If you prefer to decorate the middle tier of the slide not only with flowers, but also with green foliage, then universal choice there will be a brietta. This plant not only blooms beautifully from the end of May, but also has decorative foliage.

In our latitudes, geyhers, alpine aster, armeria bushes, bulbous plants, primroses are perfect for the middle tier.

To learn how to properly lay turf, click .

Create the foot of the hill

The lower tier of the slide serves as its foot, a logical conclusion. This is where the slide should connect with the rest of the garden.

The lower tier of the rock garden must be filled moisture-loving plants who feel at ease in the shade. Shrubs and tree-like plants are well suited for this, which will be an excellent accent.

To make the foot of the hill bright, you can plant lyatris with spike-shaped flowers, as well as saxifrage in the form of bushes. Having planted rhododendrons at the foot of the hill and dwarf conifers you will be satisfied with the result.

On the choice of plants for the alpine slide, see the video:

Examples of creating an alpine slide

Consider some examples of simple alpine slides.

A small alpine slide, consisting of fragrant plants, looks good.

Plant an oregano at the top to attract insects. middle tier decorate with beautifully growing hyssola, monard and sage. And decorate the lower tier of alipinaria with thyme, basil and nasturtium.

This combination of plants will create beauty in your area, and the combination of fragrant herbs will improve your mood.

Alpine slide scheme will help create beauty on your site

For lovers of a wide variety of plants suitable option alpine hill, on top of which coniferous plants are planted, for example, thuja. Near it, the coniferous ensemble can be supplemented with mountain pine and prickly spruce.