Open entrance without key codes. How to open any intercom without a key? (Cyfral, Visit, Metakom, Eltis)

Quite often there is a problem when the keys to the intercom are lost or forgotten, however, there is a way out, this is the input of a special code that was set by the manufacturer of this intercom device. All details below.

An intercom kit is necessary in order to ensure security at the entrance apartment building, since criminals usually wait for the victim in open, unprotected entrances to get into the apartment. Also, the intercom ensures order and cleanliness in the entrance, as it scares away lumpen and outcasts.

You need to know that entering a special pin code with mercenary intentions is punishable by law.

Modern intercoms have not only the ability to communicate, record a conversation, but also video surveillance, which gives 100% security. Many intercoms are equipped with a special code so that you can open (if you forgot or lost the key) in emergency situations (unlock), as well as a loud emergency notification system when people are evacuated from the building in case of fire, earthquake and other situations.

When using the intercom, the following instructions should be followed:

  1. When leaving the entrance, you must press the button under the screen and wait sound signal, only then exit.
  2. When entering the entrance, you need to lean the key-chip against the reading panel of the intercom device, when a sound signal (impulse) sounds, you can unlock front door.
  3. After leaving or entering the entrance, you can not help the door close, it will close itself with the help of a hydraulic closer.
  4. If you push and help the door close, this can lead to damage to the door closer.

The main components of the intercom are: a company name plate, a call block, a primary power source, an independent switching unit, an independent electromagnetic lock that magnetizes a magnet to the door plate, a door closer, a call button, apartment blocks, a keyboard.

Intercoms are divided into multi-subscriber and low-subscriber, according to technical device, multi-wire and two-wire. In the age of new technologies, there are intercoms that receive and send a signal using Wi-Fi, based on optical fiber.

Do not panic if you do not have the keys to the intercom with you, or it has become demagnetized, the encoding has flown off (recoding and programming is required). You can deceive any intercom using a universal key-chip, which is available to ambulance doctors, police, post office workers (postmen), house management workers, Internet communications (Rostelecom). These keys are made in the form of a special tablet, radio key fobs, two-pin key and are legally issued to employees of special services.

Method description: how to open a Metakom intercom

Domestic intercom Metacom is used for apartment buildings for protection from unwanted guests. What to do to open the intercom, is it possible at all?

The main thing is not to break the screen, but to make (restore) the lock by entering a combination.

To open a Metacom intercom without a screen, you need to dial a special combination consisting of several numbers and letters. Firstly, press the button responsible for the apartment number - B. Secondly, dial the code 5702.

If the intercom does not open, then you can try to enter the codes:

  • 64434;
  • 1256;
  • 1256;
  • 4978.

If the intercom Metacon of the MK-20M / T series, forward or Pro, then you must enter similar combinations or a pin code (B + 27, B + 5702). It takes a very long time to go through all the codes and you can either wait for someone to enter or leave the entrance, or call the neighboring apartment and say that you are a neighbor and forgot the keys. And remember that the use of all fraud with mercenary or robbery intentions is punishable by law.

Example: how to open an intercom Visit

Intercom Visit is one of the most reliable devices and is adapted to such harsh conditions as low and high temperatures, wind, rain. The body of the intercom has an anti-corrosion coating, which ensures reliability.

The intercom of this model works in a humid climate. The average service life is about 10 years.

Intercom Visit in case of emergency can be opened with a special code, you should log in to its menu and dial #999. After 2 beeps, enter 1234. You need to wait a bit and after a short beep, dial 2#3535.

If, after entering the combination 1234, there was no short signal, but a signal similar to two-tone or others was heard, then other combinations can be entered:

  • 6767;
  • 3535;
  • 12345;
  • 11639.

After the dialed combination, you must enter 2#3535. Actual for the following models: Vizit N-100, Vizit SM-100, Vizit BVD-341, Vizit BVD -313 and others.

How to open a Cyfral intercom

Digital has many models: Digital INTEL, Digital CCD-20.40, Digital CCD-40TS, Digital CCD-2087.2TV, Digital CCD-2087.2T, Digital CCD-2087.2T R, Digital M-10MR, Digital M-10MT, Digital M-20MTV, Digital M-20MZV.

For a Cyfral intercom of a regular model, for opening without a key, you must enter the following numbering:

  • Call + 100 + 2323;
  • Call + 200 + 2323;
  • Call + 300 + 2323;
  • Call + 400 + 2323;
  • Call + 500 + 2323;
  • Call + 600 + 2323;
  • Call + 700 + 2323;
  • Call + 800 + 2323;
  • Call + 900 + 2323;
  • Or choose the following combination Call + number + 2323 or 7272, 7273.

To pick up the code, it takes time, it is better to call a neighbor in the apartment. For the Cyfral M intercom, it is easy to open using the combination Call + 37 or Call + 3792. The Cyfral intercom of the CCD-2094.1M series is opened by the code Call + 0000, after which ON will appear on the display, you must enter 2.

If these operations do not work, then the factory access code was changed by the housing and communal services employees.

If you are with a tenant of this house, then you can get the access code from them if the key has been lost. The intercom of the Cyfral CCD-2094M model can be opened by dialing the combination 0000 + call, after the entered cod will appear on the display. 123456 + call, if it does not work, enter 456999 + call, or 123400 + call, after that f0 appears on the intercom display, then enter 601.

Hacking the intercom model Rainmann (Rainmann) 2000 is possible by entering the combination - key + 987654, after a double intercom signal, enter 123456, after which P appears on the display. The letter P on the display monitor indicates that you have entered the service menu, in which you can carry out control with numbers and program the code with your own hands.

Enter a single number:

  • 4 - block and disable the Rainmann intercom;
  • 6 - turn off Rainmann;
  • 8 - open (the door is demagnetized).

The intercom of any DomoGuard model can be opened by entering the combination C + 669900 + call + enter a number 1 more than the number of the last apartment in the entrance. After typing combinations, F will appear on the intercom display, which will mean access to the service menu. After that, we dial the code 080 to enter a new key 2, 2, 2 into the intercom memory. To disable the door lock - 071.

Instructions: how to open the Eltis intercom

All Eltis intercom models open after entering a special combination, however, if the entered combination does not open the door, then the factory settings have been changed. Intercom Eltis (Eltis) can be opened by entering a universal code that can fool the security device.

  • Call + 973;
  • Call + 7456;
  • Call + 2323.

With the same combinations, in which the call button is pressed at the beginning, you can open the following types (access intercoms) - Tekhkom, Stroymaster, Marshal, Belsplat (Belsplat), Kamsan, Condor, Lock, Poly, Filman, Polylock, Smartel, Laskomex, Modus, Polis and others.

Intercom code

Intercom brand Factorial different models can be opened without a key by entering a special software access code - 000000 + 123456, 5 + 3453475 + call + 7 + call.

The Keyman intercom can be opened by entering - K + 100 + 789, after the signal has sounded, enter 123456. After displaying the Keyman R on the display, which allows you to enter the menu, enter 8. If the intercom has a touch screen, then in winter it can be opened by application of a snowball to the screen, hypothermia can ruin the intercom.

It is also possible to open the device using the piezoelectric element of the lighter, which is applied to the place for the key, but this does not always work and is weak.

Intercom Barrier II, 2M and 4 can be opened by pressing 2 + 4 or 2 + 7. You can also magnetize the place where the key is applied and magnetized with a magnet. In the same way, you can open the Arkades intercom with an empty plastic key.

The intercom Raikmann and Rainmann and Smartel can be opened like this:

  • Key + 321654;
  • After the beep, enter the numbers 123456;
  • When P appears on the display, enter 8 or recode with a shocker or stun gun, which, with its impulse, can turn off the intercom device.

The Blink intercom is the only audio intercom installed in Belarus, Ukraine, Kazakhstan and you can open it with a D9-0.1, 6F22 battery, which we put in a turnkey place. And the intercom Cron, Pirrs and Safe can be opened using the factory combination 951. The intercom pier 1000 Micro can be opened using the factory access code - 12345678 + K + 1234 or 8310649 + entrance number.

You should know: how to find out the code from the intercom

The intercom is the most reliable device for protecting multi-storey buildings, garages and private houses. Residents of the building or the owner of the garage must know the password and secret codes for emergency opening of the intercom. This password is used if the intercom key has been lost or forgotten.

If the key to the intercom is lost and the password has been forgotten, it is not possible to open the door, then you need to call the housing and communal services, service or company, a single service center who installed this intercom device so that the master could unlock the combination locks. Remember that unauthorized entry and hacking of the intercom at the entrance of the house in foreign territory is responsible for their actions.

Why is it not worth entering codes and physically trying to open the intercom without a key? There is an instruction where it is written that it is strictly forbidden during the operation of the intercom to cause any mechanical damage to the call unit, handset, electronics unit, electromagnetic lock, opening button and intercom housing various items, which can lead to damage to the device or its individual elements.

Mechanical damage also includes wiping with snow, dousing with water, heating with fire, dousing with paint and other solutions, using a magnetic key with an electromagnet, tearing out buttons, repairing the device yourself or coding it.

It is forbidden to independently perform recoding, unlocking or other actions by a person who is not a service employee of the intercom device. Do not pull the door behind you, which can lead to breakage of the hydraulic closer. The closing speed of the entrance door is set by the master, depending on the structural features of the door and the adjusting screws.

How to open an intercom without a key (video)

In conclusion, it is worth noting that it is forbidden to put foreign objects under the door from the inside and outside that prevent the door from closing independently and lead to unauthorized entry of strangers into the territory.

Now it is difficult to find a house that is not protected by a special system. This wonderful device warns against uninvited guests. But what to do if you forgot the magnet at home, or it stopped working. If it happened in daytime, you can wait until the neighbors open the door. What if at night? How to open the intercom without a key in this case? We have collected the most best advice to solve this annoying problem, depending on the brand and model of the intercom. Enjoy!

An intercom system is a security measure that is applied to. It is used to connect the guest with the owner and is installed in apartment buildings or offices.

It can be used to solve a wide variety of tasks:

  • the simplest system will help organize the entrance of clients to the organization or guests to private housing;
  • organize a more complex system and the ability to record the history of events;
  • additional device .

For all the time of using intercom systems, no one doubts their effectiveness. The issue of choice is a financial issue.

The principle of operation of the intercom system

The device is quite simple and consists of only a few components:

  • call block. It is presented in the form of a panel protected from dust and moisture penetration;
  • inner zone, which includes intercom(call key, microphone and loudspeaker) and door station;
  • latch lock;
  • subscriber complex. It is made in the form of a tube and is installed either at the reception in the office. On it are located: control button, microphone and speaker;
  • magnet with chip.

The intercom can be provided with an audio or video signal. All elements are connected through a switch.

The intercom device works by analogy with a relay connection as follows:

  • the guest presses the "Call" button on the external panel;
  • contacts are closed, the signal reaches the subscriber complex of the owner;
  • the host of the receiving device presses a button to negotiate;
  • by the decision of the owner, he can, by pressing a button, unblock the entrance system or refuse to accept.

Manufacturers initially set a password to open the door mechanism. When installed at the request of the owner, it can be replaced either on the main unit remote control or through software.

How to open an intercom without a key: basic methods

If you didn’t have a magnet with you, or it stopped working, you need to contact your familiar neighbors. You just need to dial their number on the device and explain this trouble. If they are at home, they will certainly provide access to the entrance.

But this situation does not apply to all cases of life. For example, appliances are not installed everywhere. Or the systems are off. In this case, you can knock on the windows of the neighbors on the first floor. The owners will understand the huge problem and help unlock the system.

And if you are the owner, and you simply do not have neighbors? Or another option - you returned at night, and calling someone is simply indecent? In this situation, code should be used.

No need to try to enter the entrance by force or break the dashboard. This will not help unlock the lock. In addition, the doors in this case are not unlocked from the inside, and you will have to pay for the repair of both the door and the intercom system. Even administrative penalties for petty hooliganism can be applied.

Universal key for intercom: do it yourself

Several options for keys are produced for modern intercom systems. Their main task is to open entrance lock with security controls. All of them are programmed with a specific factory code. If the firmware was changed during operation, in this case, only Customer Service. After their intervention, it will be necessary to re-program the device.

Firms that are engaged in programming locks use a special technology for opening devices:

  • contactless;
  • tablet-chip;
  • all-terrain vehicle;
  • universal key for intercom.

With the help of the latter, you can open up to 95% of the models. It is convenient to use, as with its help you can quickly solve the issue of opening doors. It is these devices that are used by service workers or postal workers.

The key called "all-terrain vehicle" can also be attributed to the universal ones. Utility workers may not be carrying around large bundles of chips. It is enough to have one universal. The programming device is located in the chip, it is enough to attach it to the contact located on the input panel.

There is another way to open intercom devices using a universal key - a contactless master key. To do this, there is no need to apply it to the contact on the panel. The principle of operation is at a distance. She has one significant drawback - high cost.

How to make a universal device yourself

Such a device is not difficult to perform for someone who is familiar with programming and has the skills of a radio mechanical engineer. You need to know the name of the model. Information about which blank is suitable can be found on the Internet. There are also tables for combining the duplicator and blanks.

Making a new device takes a few seconds. To do this, you need an “emulator” device. This is a device that opens almost all intercom systems, with a few exceptions.

But even the most professional master, the best software and emulator may not be able to handle some devices. It is necessary to personalize the emulator for a certain version, then the cipher will be easily selected for this model.

How to open an intercom from well-known manufacturers if you forgot your keys

An excellent solution to the problem of how to open any intercom is a password. It is installed in the firmware. It should be clarified with the workers who were involved in the installation of the intercom device, or found on the Internet.

For many devices different manufacturers the same cipher fits. This applies to devices Vizit or Eltis . But here for new system Cyfral no password provided.

It is important! The password embedded in the program of the intercom device works even if it is deprived of a memory card.

In most cases, if the codes are programmed by the manufacturer, the passwords can work in all cities. Sometimes intercom systems can be encrypted by the installer company. Then you need to ask for a password from them. In any case, services that require the daily opening of systems, such as postal workers, have a code. You can check with them the password from the intercom device.


How to open the Vizit intercom without a key

This is the most common system. If the original firmware has not changed, the algorithm for how to open the Vizit intercom is as follows:

  • 12#345;
  • *#3423;
  • *#4230.

For new devices "Vizit" will suit:

  • 67#890;
  • *#423.

You can use the following codes to open the Vizit intercom without a key (suitable if it has not been opened before):

  • #999 - double ring, then the service panel code 1234. If this dialing does not work, there will be a double beep. If all is well - one beep.

If the service cipher is incorrect, we dial not 1234, but the following options:

  • 0000;
  • 3535;
  • 9999;
  • 12345;
  • 11639;
  • 6767.

To determine whether the cipher is correct or not, the beep will help: if it is wrong - 2 beeps, for the correct one - only 1.

When the menu worked with one call, you need to add your own code:

  • to operate the lock: 2 - pause - # - pause - 3535;
  • then you should add your own password: enter the number 3 and lean the chip from the panel, then # and wait for the sound of the lock.

Important! You must remember to delete all settings from the service settings memory. To do this, press 4 # *.


How to open the Forward intercom without a key

Manufacturers of these models often do not make their information publicly available. Only three sequences are known:

  • 123 * 2427101;
  • K + 1234;
  • 2427101.

To include your password in the service settings, you must enter:

  • 77395201 + * +0 *, put the chip against the device and press # twice.

If this sequence did not work, you can dial 5755660 instead of 77395201.


Intercom "Cyfral": how to open without a key

These are the most modern intercom models. If you don’t know how to open the Cyfral intercom without a key, then you should follow the following algorithm. It will work if there are apartment numbers in the entrance that are divisible by 100.

To open the Cyfral system, you must press:

  • "B", apartment number, which is divided by 100, then again by "B" (for example, B400B);
  • then 2323. If it doesn't work, press 7272 or 7273 instead of 2323.

The question may still arise, how to open the Cyfral CCD2094 intercom. It opens a little differently:

  • "Call", then 41, or 1410, or 07054.

If the system did not work, you should continue in this way:

  • "Call", then 0000.
  • if we hit the "Menu", but the doors are still closed, you should press the number 2.

If there is a problem, how to open the Cyfral CCD 20 intercom, all the methods listed above are suitable for solving it.


How to open the Eltis intercom without a key

It is quite difficult to work with this system without a chip. The password may not be suitable for all devices. The algorithm of actions is as follows:

  • V 100 V 7273.

Alternatively, we enter not 7273, but 2323.

Another way to open the Eltis intercom without a key: the technique used for the Cyfral model is suitable


How to open the Factorial intercom without a key

Factorial models can be opened by dialing 000000 or 123456. Alternatively, dial 5 and hold until a text message appears on the dashboard. Then you should enter 180180 and "Call".


This is the rarest device in terms of encryption without a passkey. The procedure is as follows:

  • K - 100 - 789 - short beep - 123456 - 8;
  • K - 170862 - short beep - 0.

Difficulties with the Blink system

Unfortunately, there is nothing to help in this case. These are not access intercom systems, but individual ones, which are produced for individual houses or houses with a concierge. There is no universal code for such a system. For assistance, contact the service department.

Codes for the device "DomoGuard"

This is a fairly rare model. To open, you need to type:

  • "C", beep, code 669900 and "Call", then the number of the last apartment in this entrance +1.

The display should show "F-". We get into the service settings. After that, you need to perform the following algorithm:

  • 080 - open the lock;
  • 333 - remember the password;
  • 071 - turn off automatic locking.

Intercom system "T-Guard"

For this model, the following algorithm should be performed:

  • on the panel, press "Call" or "Call", enter 00000, twice on "Call".

All actions must be carried out with maximum speed, otherwise the intercom device will not work.

Rainmann system

To activate the device, you need to dial:

  • "Key", code 987654. After the call, dial 123456.

If everything is correct, we got into the service menu, the P icon will appear on the display. To unlock and open the lock, press 8.


How to open an intercom without a Metakom key: codes

This device will fit the following:

  • "B" (CALL) - the number of the first apartment in the entrance - "B". "COD" will appear on the panel. Further 5702;
  • 65535 - "B" - 1234 - "B" - 8;
  • 1234 - "B" - 6 - "Call" - 4568.

For "Metacom-20 M / T" the following combinations are suitable:

  • "B" - 27 - "B" - 5702;
  • “B” - 1 - “B” - 4526 - then for programming, lean a clean key (not previously programmed) against the dashboard.

Conclusion

The proposed options, how to open the door without an intercom key, can be applied if the manufacturer's primary parameters changed during installation. In addition, it is important to know which manufacturer's device is installed in the house. The use of these algorithms can be used in the rarest cases, their use for selfish motives can be criminally punishable.


In this video, tips are shared by professionals:

YOU MAY ALSO BE INTERESTED IN:

A steel door with is an excellent means of preventing unauthorized access and various hooligan actions.

The problem is one. A tenant of an apartment in the entrance can lose, forget at work, drop a small intercom key-tablet in the car.

For those who live alone, it is enough to press the call button so that the household inside can open the door. It will be useful for the rest to know how to open the Cyfral intercom without a key.

Ways to open the Cyfral intercom without a key

Intercom Digital belongs to a series of devices with the largest number firmware versions, software and hardware implementation.

Its hack depends:

  1. from a specific model;
  2. access codes may differ depending on the firmware version;
  3. the code from the intercom Cyfral CCD 20 is entered in two groups;
  4. for some models - you can change the combination set for access directly from the keyboard;
  5. the digital code may depend on the number of subscribers for which the model is designed;
  6. some versions have a universal code from the Cyfral intercom.

Most models - designed to access most functions directly from the front panel. In particular, you can memorize a new key from the Tsifral intercom.

However, you can try the following methods to unlock the door:

  • use Cyfral code 2094 if the particular device has a firmware version compatible with this series of locking devices;
  • select combinations corresponding to the apartment or subscriber number;
  • apply one of the complex combinations suitable for Cyfral intercoms of the model installed on the door;
  • use the service entrance;
  • to program a new combination.

It is worth noting right away: the universal key gives much more freedom, it can be ordered in many workshops and companies, including installation or repair of intercoms.

By apartment number

If the house is large and a locking device is installed on it, designed for three-digit addressing of the apartment, then the method of how to open a digital intercom is as follows:

  1. a code from two groups is dialed. The dialing begins by pressing the call button or K, depending on the series, then the first three numbers are entered, then the call button or K again, after which the rest of the combination;
  2. there are a number of standard combinations for apartments, they are grouped by the first digit. For example, apartments from 1 to 99 are not addressed, the rest are grouped in hundreds;
  3. group codes look like this: 100-7272, 100-7273, 100-2323.

In order for the door to open, it is not necessary to live in an apartment with a specific number.

These are only unlock codes that are hardwired into the software part of the intercom. Similarly, for example, 100-7272, combinations 200-7272 are dialed and so on, up to 900, according to the algorithm indicated above.

Via service mode Cyfral CCD 2094

Cyfral CCD 2094 has two circuits for easy unlocking of the locking magnetic device. The first step is to try the first activation level.

Methodology, how to open the intercom Cyfral CCD 2094 simple method, looks like that:

  • drown the call button;
  • press four zeros;
  • if the display shows readiness in the form of the inscription On, enter 2.

Upon successful activation of the emergency opening circuit, the magnetic locking device is unlocked. But it may also be that the set of numbers was changed by the installer.

In this case, after entering zeros, the display will show a concise Off. This means that access to the service is blocked.

In some series, the method of how to open the Cyfral CCD 2094 intercom without a key uses access directly through the service menu. The models under consideration have only one emergency mode for unlocking the magnet.

To try to open, you need:

  1. press call;
  2. enter four zeros;
  3. after the inscription Cod appears on the display, use one of the combinations 456-999, 123-456, 1234-00;
  4. you need to complete the input of each set by pressing the call. Upon successful entry into the maintenance mode, the display will show prompt F0.

You need to try a new combination from the very beginning, that is, by pressing the call, zeros, receiving an invitation. Upon successful login, hint F0 - just dial the numbers 601.

The door will unlock. If this did not happen, the Cyfral intercom opening code on this particular entrance door can only be obtained from the personnel who installed the device.

There is also a third method. The process of how to open a Cyfral intercom without a key, the codes on which have not been changed, and the firmware is such that other methods do not work:

  • dial four zeros;
  • when the On prompt appears, indicating that you are waiting to enter the service, press the deuce;
  • when prompted for Cod, enter the six-digit numbers indicated above.

With an unsuccessful outcome of events and zero options, how to find out the Cyfral intercom code - you can try the last way to bypass protection.

Change device security code

Some versions of Cyfral devices have the ability to easily change the unique dial to unlock the magnetic block. Its change depends on model range and firmware versions.

In the 2094 series, you must follow the same steps as when trying to unlock the constipation through the maintenance menu.

Namely:

  1. dial four zeros:
  2. press the deuce in response to the prompt On.

After the Cod prompt, you can try to set your own unique set of numbers to deactivate the lock. To do this, the combination button K - zero - button K is typed.

After it, the keys of a new set of numbers are pressed, in the amount of four pieces. If there is no such code in memory, it is considered unique, remembered as the main one, the door is unlocked.

For the most popular series, the method for opening the Cyfral CCD 20 intercom by changing the main control code is as follows:

  • press K;
  • dial 98;
  • press K again;
  • dial the control combination 46-33.

This method works only on devices where the installation wizard did not do programming with a change in factory settings during installation. If this has been done, the option of how to open the Cyfral CCD 20 intercom without a key looks like this:

  1. dial a combination of buttons K-zero-K;
  2. dial 1234;
  3. after a hint in the form of Pr_ on the display, which means the activation of the service menu - press 5;
  4. after a pause, a new digital combination (4 characters) is entered, then it is repeated.

If everything is completed successfully, the device will emit a short one-tone signal, indicating that the new set of numbers is now the main release code. This opens the door. The new combination can now be used to access the entrance at any time.

For models with index M

Intercoms of the Cyfral brand, with a numerical - letter designation of the model that ends in M ​​- are unlocked by one of the combinations described above.

A distinctive feature of these devices is the presence of the widest range of firmware options, so hacking can be long, with a search of all possible sets of numbers and access methods.

A series of models, the symbolic-numerical designation of which ends with the letter M, also has its own, unique code for opening the Cyfral intercom. For access, you can try dialing the combination call - 41 - call - 1410, and then the 07054 series.

Always worth remembering!

If none of the algorithms works, most likely, the wizards changed the factory settings of the device during installation and it will not work to unlock the door without an electronic tablet.

Conclusion

It is worth remembering that you need to act carefully when opening the entrance, without going beyond the algorithms given.

If we are talking about Digital series devices, it can be especially noted that the maintenance menu allows not only changing the main unlock code, but also blocking a specific subscriber, resetting information about all keys, and getting other unpleasant consequences.

In order not to order many separate keys to the entrance of the house, mother's apartment, favorite hairdresser, fitness center, it is most reasonable to order one universal electronic key that will open all the doors.

The model range of locking mechanisms, as well as firmware, is constantly changing, so the opening options are constantly changing, becoming outdated.

Video: How to open a Cyfral intercom. Code from the intercom Сyfral

Almost all people at least once got into a situation where you need to open the intercom, and the key to it was left at home or at work. In this situation, you have to wait for other owners of the cherished "pills" who can open the front door. If your home has a concierge, then you can, of course, seek help from him. But even this person cannot be permanently at his post. In addition, they sleep at night, and waking up a person at three in the morning with a request to let him into the house is not the most best idea. If the concierge does not know you by sight, and you cannot confirm the right to get into apartment house, then there is a high probability of spending the night on the street. If there is no concierge, then your only chance is to call the owner of the other key.

It is for these cases that knowledge is useful secret codes that allow you to hack Cyfral intercom and without any problems to open the front door. We remind you that this information should only be used for the purpose of infiltrating own apartment. If you use these codes for criminal activities, you will be prosecuted.

How does the digital intercom work

How to open a Cyfral intercom without a key

The peculiarity of all intercoms is that they have setting mode. And you can get into it with the help of special installation service codes. They are needed so that the installer can configure the system as needed. Once configured, they are modified by the wizard. But initially the secret codes are the same for all models, such intercoms come out of the factory. And this is where the system's most serious flaw lies.

The fact is that hacking the intercom is very difficult. Finding out the code exposed by the installer is not an easy task. To do this, you need to calculate the installer himself and get the coveted numbers from him. In the event of an urgent need to get home, this will be problematic. And without the secret code entered by the installer, you will not be able to open the intercom.

But to do this will allow - human laziness. The problem of intercoms lies not in programming, but in non-compliance with instructions by installers. The wizards set up the system by first entering secret code. And after setting up, they simply leave without changing the sequence of numbers on the intercom. Their carelessness allows you to enter the house without having desired key.

If you want to know how to open a cyfral intercom, then never mind to the so-called "universal" codes. They may fit intercoms from other manufacturers, but not this one. The thing is that each company uses its own secret service code. That is why they differ depending on the manufacturer. Moreover, different models produced by the same company may have different codes. That is why you should pay attention to the device model if you are trying to learn how to open a digital intercom.


Intercom Models Digital

Ways to open a Cyfral intercom without a key

In the case of devices from this company, you will first have to determine the model. If you cannot understand which intercom is exactly in front of you, we recommend that you systematically check all possible ways. If the installer has not changed the system codes, then one of them will definitely work.

Method number 1

The first option can only be used in houses with more than a hundred apartments. That is, in the entrance there must be an apartment with a number that is a multiple of 100. In this case, the code is entered as follows:

  1. First, press the call key.
  2. Then enter the apartment number, a multiple of 100. It can be 100, 200, 300, etc.
  3. Press the call key again.
  4. Now enter one of the combinations: 7373, 7272 or 2323. If the first combination does not fit, then try entering the code again, but with a different set of numbers.

Be prepared for the fact that these codes will not work. There can be only two reasons: in front of you is a model that requires a different approach, or the installer has changed the system code in the equipment settings field. In the second case, you cannot do anything, but in the first case, there are options.

Method number 2

It is used for models whose number ends with the letter M.

You need to start with the call key. But then the short code "41" or the longer "1410" is entered. Not some models have a different code that is entered immediately, without pressing the call button.

Enter "07054" quickly without making long pauses between presses.

How to open intercom Cyfral ccd 2094

With this model, you will have to "sweat" a little, as it requires a more serious approach.


Appearance intercom Cyfral ccd 2094

You will need:

  1. Press the call button
  2. Enter "0000".

After that, keep a close eye on the screen. If the inscription “ON” is displayed, then you have entered the service menu. In this case, you need to press the number "2" to open the door.

If the inscription “OFF” lights up on the screen, then in this way it will not be possible to open the cyfral ccd 2094 intercom without a key. The installer has disabled the built-in fast login feature, and you won't be able to activate it yourself.

But this is not a reason to abandon your idea. Use another method that can open the door for you.

You need to start by entering the numbers "0000" to get into the menu. If you see the inscription "cod" on the screen, then you are moving in the right direction.

Now you need to enter one of the possible secret codes: "123400", "123456" or "456999". Press the call button. If the inscription “F0” appears on the screen, then the code has come up. Otherwise, you need to try another possible combination starting from the first step.

After you see "F0" on the screen of the device, enter the numbers "601" to open the door. This method is one of the most difficult.

How to open the intercom Cyfral ccd 2094 - video

How to open the intercom Cyfral ccd 20


The appearance of the intercom cyfral ccd 20

This common intercom model Tsifral opens with a simple combination.

First you need to press the "K" key, then enter the numbers "98", then again "K" and "4633". This way you can get into your house. Opening the cyfral ccd 20 intercom without a key using these numbers will only work if if the installer did not change the secret code. Another option looks like this: "K", "0", "K", "1234". After that, the message “Pr_” should be displayed on the screen. After that, you need to press the number "5", and then enter the code, consisting of 4 digits. You can invent it yourself. After that, duplicate the code. You will hear information that the new code has been recorded. Use it to enter the house.

How to open the intercom Cyfral ccd 20 - video

If you are looking for information on how to open intercoms without a special key, our article is for you.

Now it is rare to find an entrance to the entrance of a residential building that is not equipped with protective device. Situations when you need to open the door without a special key are quite common.

The intent to seek information on this subject is not necessarily fraudulent or criminal in nature. Perhaps you do not have access to your own entrance due to a lost or broken key, or you want to visit a loved one who is sick or does not answer calls for a long time. In such cases, opening the door without a key fob is permitted by law. For other purposes, the use of access without the permission of residents is treated as burglary and damage to private property, which may be criminally punishable.

Opening the intercom with a code

How to open any intercom without a key?

  • To easily enter the entrance, equipped with an electronic access restriction system, it is enough to know the specifics of the device itself. In the design of almost every modification, there is a microphone and speaker built into the external panel. To create an effect feedback, close the intercom panel with your palm in order to maximize isolation from extraneous noise. will appear alt(you can hear a similar one if you bring a working microphone closer to the speaker of the speaker), at the moment of amplifying the sound, you need to pull the door handle. If everything is done right, door lock will be unlocked.
  • You can use a special key. This tool allows you to open the intercom of virtually any modification, but does not give a 100% guarantee. Meet universal keys, suitable for certain brands of devices - with such tools, the probability of a successful "hack" will be much higher (up to 99%).
  • It is possible to open the intercom by using force. To do this, rest your foot well at the bottom of the door under the handle and pull sharply. It is not necessary to use huge force - it is important to make the right emphasis. Pulling the handle smoothly will not work either - a sufficient jerk is needed.
  • One way to open it is to use a piezo element, for example, from a regular lighter. You need to shock exactly in the place where the key is inserted. Of course, this method does not always work.
  • Models of intercoms equipped with a touch keyboard can be affected by hypothermia. Check the effectiveness of this method to get only in the winter. To do this, take a handful of snow and press it against the button area. When the display shows the message "Err" (after 10-15 minutes), the lock will be unlocked.
  • An option is also to short the light bulb at the entrance to the entrance. A short circuit will cause a power outage in the entrance, which means it will turn off the intercom. This method is one of the most dangerous in terms of possible unpleasant consequences.
  • Each intercom has its own program mode. You can use this function after entering the characters of a special cipher from the keyboard. With this code, you can open the door, as well as change some system settings. The system codes are programmed at the device manufacturing stage. For the same model, they are the same by default, but can be replaced during installation and installation. Basically, installers do not program unique codes, so most devices are opened by entering factory codes.

Opening the intercom if the key does not work

How to open a Vizit intercom without a key: codes

Visit models are recognized as one of the most secure and most difficult to open. On the keyboard of some models, there are no * and # buttons; instead, the characters "C" and "K" are entered.

  • If no changes have been made to the default system settings, access can be gained by entering the code *#4230 or 12#345 .
  • The latest models of audio intercoms Visit open with ciphers *#423 or 67#890 .
  • To unlock the lock using the service functions of the device, dial # 999 , wait for 2 short beeps, then enter the system password 1234 . If the password was entered correctly, a single high-pitched beep will be heard, if it was erroneous, a two-tone signal will be heard. Then try using one of the possible digital combinations: 0000, 6767, 3535, 9999, 12345, 11639.
  • If you managed to enter the program mode of the device using any of the indicated options, type the following characters: 2 # 3535 – activation of the door lock release function
  • Pressing the button " W» allows you to program custom keys. Press your magnetic key against the reader while holding down the key # until you hear a short beep - your key is saved in the hardware memory.
  • * — exit from the current parameter setting, # — confirmation of the modifications made.

Intercom VIZT

Video: How to open a Vizit intercom. Intercom code Vizit.

How to open a Cyfral CCD intercom without a key?

Cyfral devices are the most common in our country. Such models were installed a long time ago, but most modifications have standard access codes.

  • Method 1
    If there are apartments with numbers divisible by 100 in the entrance, do the following:
    "B" cipher1 "B" cipher2
    code1 - apartment number
    cipher2 - 2323, 7272, 7273
    In other words, you must enter "B" 300 "B" 2323.
  • Method 2
    Use one of the options:
    "B" 41
    "B" 1410

Some modifications of the Numeral open after the introduction of numbers 07054 .

Model CCD-2094.1M opens as follows:

  • "B" 0000
    The door will unlock or the device will be put into system setting mode (the screen will display the message “ ON"). Then enter a number 2 .
  • If you see the message " OFF“, so the set of standard codes was reprogrammed during the installation process and the idea of ​​breaking the door will have to be abandoned.

To hack model CCD-2094M use the code 0000 and press " B«.

  • The display should show " COD". Then type one of the combinations:
    123456 "B"
    456999 "B"
    123400 "B"
  • Wait 3 seconds until the message “ F0» - then access to the program settings menu will be opened. Enter the code to enter 601 .

If necessary, on this model, you can try to set your own key from the Digital device, if you have one:

  • Hold down the " B» button pressed until the machine enters the service setting mode.
  • Then click 5 and enter the number desired apartment. If the display shows the message " TOUCH”, bring the key to determine and save in memory.

Intercom CYFRAL

How to open a Metacom intercom without a key: codes

The opening of most Metacom models is performed as follows:

  • Press the call, indicate the initial number of the apartment from all located in your entrance, and call again. On the screen you will see the message " COD", after which you need to specify the characters 5702 .
  • If this technique does not bring the expected effect, use the character sequence: 65535 call 1234 call 8

The Metacom MK-20 M/T model differs in that this device does not provide software system restrictions from the definition of the master key. Thus, if you press a non-sewn key to the reader, the programming mode will be automatically switched on, which will allow you to unlock the door.

If the key is not available:
call 27 call 5702
call Z call 4526

Intercom Metacom

How to open an Eltis intercom without a key?

Eltis models are considered the simplest in terms of opening, since they have a small number of system codes and a low level of access protection:

call 100 call 2323
call 100 call 7373

Intercom ELTIS

Video: How to open a Cyfral, Eltis, Vizit intercom.

How to open a Marshal intercom without a key?

For models from this manufacturer, enter from the keyboard maximum apartment number in the entrance, increased by 1(for example, if the highest number is 15, then enter 16) followed by " TO» 5555 . This method works on most Marshall devices.

Intercom Marshal

How to open a Factorial intercom without a key: codes

  • The order of opening the Factorial is similar to using the system functions of the Cyfral models. Entering the program settings is done by dialing one of the 6-digit codes (use the symbols 000000 or 123456 ).
  • Representatives of the company claim that hacking the device of this brand is almost impossible, since the replacement of the system code during the installation process is an essential condition for the service.
  • Try the following combination:
    Hold down a number button 5 until the system message appears on the monitor, then type 180180 call 4 call.

Intercom Factorial

How to open Rainmann and Raikmann: codes

Although the names of these models are very similar, Rainmann and Raikmann are actually different devices.

  • Raikmann modifications are programmatically protected from hacking, so it will not work to open them by entering a code without a key.
  • Rainmann CD-2000 can be hacked by pressing the " key”, then a sequence of numbers 987654 . After a short beep, enter 123456 . If the setting change mode is available, the display will show the symbol “ P", then press the number 8 . If the door does not open, it is not recommended to press anything else, as the device may be blocked.

How to open a Tehkom intercom without a key?

It is believed that doors equipped with Techcom models cannot be opened without a key. To try to do this, you need to have some kind of magnetic key from the device of this brand. Try to follow the sequence of actions:

  • Press the buttons 1, 6, 0 together (in some models 2, 5, 8).
  • Then let go to reverse order one at a time, first 0, then 6 and 1 (8, 5, 2).
  • After the beep, enter the factory key 4321 .
  • Click call 3 call.
  • Bring the key to the reading element - the lock will be unlocked.

Intercom TechCom

How to open intercom Safe Service without a key?

Safe Service intercoms may have different codes depending on the modification of the device. The standard codes set during the manufacturing process are 000000 or 123456 .

If the factory code is not suitable, use the following recommendations:

  • Press a number W and hold in this position until the soft menu entry screen appears.
  • Enter a code 180180 , call, number 4 - the device remembers the combination and opens access to the door.

Some Safe Service models can be opened using a conventional 6-12V battery. To do this, remove the bottom panel of the device, under which the mounting bolts are located. Between them you can see a small connector, it is in this place that a battery is applied, which allows you to unlock the door.

Intercom Safe Service

How to open a Laskomex intercom without a key?

These devices are a digital lock. Access to it is provided by entering the service mode:

  • Press the button with the image four times in turn key And 0 .
  • Dial the system password 6666.
  • The message should appear on the board. SSSS, then R-(this indicates the opening of the setup mode).
  • Press a number 8 (code for unlocking the door).

Intercom LASKOMEX

How to open a Forward intercom without a key?

There is quite a bit of useful information about the possibilities of accessing Forward models on the web. You can try using standard keys:
123*2427101
"K" pause 1234
2427101

If you have a key fob for a device of this brand, try reprogramming the device:

  • Enter 77395201*0*
  • Press the key to the reader and press the symbol # twice

How to open a Kron intercom without a key?

It is almost impossible to hack the devices of this manufacturer. Service key 951 , but the warranty condition for installation is the mandatory change of the system code.

How can I open an intercom without a key Stroy Master?

For devices from this manufacturer, it is not possible to enter system codes. The only option to open such a model is to enter the software menu and install a custom cipher.

  • Hold down the " B» until the inscription « SYS«.
  • enter password 1234 .
  • Enter your own code.

Doorphone Stroy Master

As a conclusion, it should be noted that not all of the listed methods of opening can work with individual device models. The reason for this may be a change in system settings, a difference in device modification and hardware installation features. It should also be borne in mind that the latest models of intercoms are equipped with improved means of protection against unwanted access and control.

Video: 5 cool life hacks with intercoms / how to open an intercom

If you are still unable to log in without a lost or broken key, contact the service company's service center to obtain a new one.

Loading...Loading...