How to glue the sole at home. What to do if the sole on the shoe is cracked

You will need

• - Glue;
• - Acetone;
• - Rags or cotton wool;
• - Press;
• - Sealant (MS polymer), silicone sealant;
• - Porous rubber;
• - Cardboard;
• - Insoles;
• - Rubber outsole;
• - A piece of cotton fabric;
• - Knife and scissors.

Instruction

Repair sole using durable rubber glue - this is the most familiar way to lead. As a rule, this is a temporary measure. If the front edge of the sole is a little unstuck (“asking for porridge”), clean the surfaces to be glued from dirt and, after drying, treat them with acetone. Usually super glue and "Moment" are used. Epoxy glue (EPD), Crazy Hands sealant and Desmokol polyurethane agent have proven themselves well in the practice of self-repair of soles.

Use glue according to package instructions. Usually it is applied in a not very thick layer (2-3 mm), kept for 10 minutes and the shoes are strongly squeezed with a load from night to morning. Ideally, this will be done in a shoe workshop using a special press. In the same use improvised means, trying not to deform the shoes. It is ideal to use an “g”-shaped block with an additional load.

If the leaky sole has a honeycomb structure, when worn, voids form in it - the heel falls through, the shoes become thinner in this place. Tear off the insole and carefully clean the honeycomb from dirt, glue residue and torn cardboard. After that, they can be filled with a sealant (for example, MS polymer) and allowed to dry properly. Cut out cardboard templates in the shape of an old insole, soak them with the same agent and glue them on sole, then install new insoles.

Sometimes honeycomb outsole due to a small puncture. In this case, the insole is also disconnected (if it is in order, then this can only be done at the puncture site). Fill the honeycomb silicone sealant, fill them with scraps of porous rubber (micropores) and apply silicone again. Place the insole on top and press firmly until the repaired sole is dry.

To correct sole, cracked across, the conditions are almost impossible. To do this, you need to contact the shoemakers and make rubber ("prevention"). The same should be done for abrasion of the heels and toes.

If you managed to get a thin rubber sole according to your shoe size, try it yourself. Use strong shoe glue. In order for the rubber part to stick to the base of nylon or nylon, first weld a precisely cut cotton lining on it with a hot iron. When sticking the rubber sole on the skin, it is recommended to make a 45-degree edge. However, more reliably repair a fracture or abrasion of shoes can only experienced craftsmen.

Helpful advice

If you plan to wear shoes for a long time, take them to the workshop right away and ask them to make polyurethane stickers. Then you will not soon have to think about how to seal the sole. Such prophylaxis is inexpensive, and it is easily replaceable. In winter, stickers will save you from ice. At this time of the year, artisanal methods of repairing shoes are only a short-term measure, as boots and boots quickly fail from frost.

Sources:

• Million useful tips

boots usually used by us only a few times a year, for example, to go fishing or to the forest for mushrooms. But they often leak, because we walk in them not through Canadian greenery, but through forests and slums. So a dilemma arises - it’s a pity to have money to buy boots, and you don’t want to go to a specialized workshop, since repairing boots there can cost, if not more expensive, then on a par with the cost of a new product. In this case, it is more rational to glue boots himself.

Instruction

Carefully cut out a patch from the old rubber along the puncture or cut on the boots requiring repair. Clean the sides to be glued, both on the boot and on the prepared patch, with a large file, and then sandpaper or sandpaper.

Spread with a brush or a piece of foam rubber on both fat-free surfaces thin layer adhesive suitable for working with rubber products. Leave the glue to partially dry for 15-20 minutes. Apply the second layer of glue in the same way through the indicated one.

Press the patch to the damaged one, supporting it with the fingers of one hand, and outside with the fingers of the other. Try to do this with maximum effort to ensure optimally strong contact between the parts to be glued. Do not use glued shoes within a day after the manipulations.

Sources:

• how to seal pvc boots in 2018

Many economical housewives and hosts do not want or cannot afford to give a significant part of family budget for repairing several pairs of shoes a year. Of course, there are types of work that cannot be done at home due to the fact that special equipment is required. However, with the help of some simple tricks, you will save a significant part of the budget, and perhaps acquire a new hobby or even new profession.

Instruction

Remove worn buckles, buttons, straps and bows, as well as sewing threads or staples that have come out with a knife or scissors. Remove the straps in those places where they fasten the buckles when replacing with new ones, completely, and partially.

New straps in shape, color, size and method of processing the edges must match those that were previously. Glue the new straps well, and then attach with a two-row bartack stitch. Attach buttons with a regular needle, at least 5 stitches with a distance between punctures of 4-5 mm.

Changing the “slider” with a zipper is also not difficult. From below, spread the threads under the “zipper” a few centimeters so as to pull out the edge of the fastener, remove the old “slider”, put on a new one, strengthen the end of the fastener with a metal bracket, threads, superglue and carefully, with frequent stitches, sew. The “runner” can be bent a little with pliers and squeezed a little. If you press too hard, then its internal parts will begin to scratch the links of the fastener, and then you will have to replace it completely.

The strength margin of the lock can be significantly increased if the lock and clasp are lubricated, for example, with silicone grease in cylinders. It is best to apply it on a cotton pad and gently wipe only the clasp and lock. After that, it will become easier to fasten and unfasten, it will not freeze, and sand and dirt will not stick to it.

If your shoes have plastic heels and need to be replaced, but suitable color if it is not scratched, then buy spray paint in cans, (car paint is also suitable). Wash your heels before painting warm water with a couple of drops of "FAIRY" The surface will be degreased (acetone will corrode, so it is better to refrain from using it). Dry the surface of the heel and spray the paint evenly from a distance of 15-20 cm. A can of car paint is worth it, but it will last for a long time. This method is not suitable for leather-covered heels.

Most often, for self-repair of sneakers, shoes, sandals and other shoes, second glue is used. Household adhesives are divided into liquid, contact, reaction and thermal. They allow you to solve almost any problem related to home repair.

contact adhesive

If it is intended to bond non-porous surfaces such as rubber, porcelain, plastic, or items that need to retain their elasticity (soles or straps), it is best to use contact adhesive in tubes or spray form. Unlike liquid glue, contact must be applied to both parts to be glued. In addition, it is necessary to allow the adhesive to dry slightly for 10-15 minutes before joining the surfaces. Glue sets instantly, but requires application great effort to hold the two pieces together. When repairing shoe soles, it is best to use a weight, such as an old iron. In order not to disturb the shape of the shoe, you can lay a layer of thick cardboard between the shoe and oppression.

reaction glue

When it comes to bonding highly loaded, non-porous items or where heat resistance is required, professionals recommend the use of reactive adhesives, also known as instant adhesives. They work instantly as soon as the active ingredient reacts with another component of the adhesive or with a certain element. external environment. When choosing a reaction adhesive, pay attention to the requirements for operating conditions. While air oxidation is sufficient for a conventional one-component adhesive to work, more specialized products may require special environments and factors to effective work. Second glue is suitable for mending heels, straps, as well as quick repair of soles on leaking winter boots and boots. Under the Moment brand, many varieties of reaction glue are produced, including one specialized for repairing shoes.

hot glue

Universal in everyday life and hot melt, widely used for repair and creativity. It does not need to be dosed or mixed and is solvent free, making it suitable for bonding all materials, including solvent resistant plastics. The glue is heated up to 110°C and applied to the surface with a special gun. With it, you can not only glue the sole or insole, but also fix the detached decorative elements or decorate a pair of shoes with rhinestones, sequins and other embellishments.

Related videos

Well, who among us has not encountered such a problem as a broken sole? The situation is very unpleasant, because not everyone knows how to glue the sole on sneakers or on any other shoes. It can be attributed to the master, but it will cost a lot, then the thought comes to mind to solve this problem on your own. To do this, you must be aware of some of the nuances that are discussed in this article.

How to glue the soles of autumn or winter shoes?

In the role of an improvised means to repair the soles of sneakers, it is suitable:

• glue, for example, “Moment”;
• epoxy sealant "Crazy Hands";
• means with polyurethane "Desmokol".

Each of them is accompanied by instructions, which must be guided during operation.

Important! Also, you must take into account that these funds are somewhat toxic. If any of them gets on the mucous membranes, they must be instantly washed off with a stream of ordinary running water.

Work sequence:

1. Since winter or autumn shoes often have honeycomb soles, for starters, you will need to deal with honeycombs. You must remove the rubber that covers them to such an area that will allow you to remove absolutely all the accumulated dirt from the holes. It happens that access to the cells occurs from the side of the insole, which, when cleaning the holes, will have to be completely and completely removed.
2. Fill the honeycomb with small scraps of micropores, and then fill it with silicone sealant, carefully sealing it.
3. Before you start sealing a broken sole, you will have to wait for the sealant to dry and harden.
4. Next, cut out a piece of rubber or micropores, which can fit into the hole in size if it is voluminous, or press out small holes with a mixture of sealant, as well as micropore sawdust.
5. According to the size of the shoe, cut the sole from a thin piece of rubber, glue it with the already prepared adhesive over the entire area of ​​\u200b\u200byour shoe.
6. Put shoes or boots under the press.

Important! The time it takes for the glue to dry completely is indicated in the instructions for it.

To prevent negative factors from causing boots or boots to quickly unstick and lose their strength, read also about:

How to seal a hole in the sole of an already summer shoe?

It is necessary to act according to exactly the same algorithm, but there will be somewhat less hassle.

In the event that the sandals are glued, then purchase a rubber sole from a professional workshop and glue it on your own with rubber glue. This can be done if the shoe has a solid base.

Important! If the sole is attached to summer shoes exclusively along the contour, in this case you will have to throw out the sandals.

We repair sports shoes

In the event that the training process takes place in gym You won't have to give up your favorite pair of sneakers. Of the domestic types of glue, it is best to use epoxy, which is designed specifically for shoes. Its cost is relatively low.

Imported glue:

1. Most suitable option adhesive - American-made glue Seamgrip. Glued with it rubber boats. If you managed to get it, you will not have to part with your favorite pair of sneakers for a long time, because this is the only glue that completely and completely solves the problem of how to glue the soles of sneakers. But its cost is quite high.
2. Imported epoxy adhesives of the Done Deal type are somewhat better than domestic adhesives, but you can’t promise the durability of sneakers when using them.

How to proceed to seal the sole on sneakers:

1. Carefully clean the edges of the hole in your sole and degrease with a solvent.
2. When everything is dry, apply a properly diluted epoxy mixture.
3. In the event that the hole is large, put a fiberglass mesh called sickle into it.
4. While the glue dries, cover the location of the hole from the outside with masking tape so that the sole remains completely flat.

Tread repair

To repair the tread, you need a sharp knife - it is best to take a shoemaker's, coarse-grained sandpaper or a grater, which is made from a piece of tin from any can with holes punched in it.

Repair goes as follows:

1. To begin, cut a patch out of a piece of fairly stiff rubber and fit it into place.
2. Using a grater and a knife, give the patch a wedge shape.
3. The surface should be rough, so it is better to process it with sandpaper, and then wipe it with a degreasing solvent and dry it.
4. After that, apply glue to the surface in two or three layers. Dry the glue thoroughly. The drying time of the first of the layers is about 20 minutes, the second - at least 2 hours, but preferably not less than 6-8 hours.
5. Then heat the glued surfaces over an electric stove or gas stove until the smell of glue appears, quickly attach them to each other, press firmly and hold for several seconds until they have completely cooled.

Shoe heel repair

In the event that the protector is thoroughly worn out, carefully tear it off the surface of the sole, cutting it exactly in those places where it is impossible to tear it off. You can moisten these places with a solvent so that the protector comes off.

Transfer the outline of your sole to cardboard, finish the erased edges, and then cut out the pattern. You can make a new protector from any rubber mat found in any hardware store.

Important! During gluing, carefully clean the surfaces to be joined, but otherwise, the gluing technology itself is the same.

Repairing soft soles

If your soft sole is worn out, then before gluing a new tread, build up a soft sole to the required thickness using microporous rubber.

Shoe upper repair

During the repair of the top of the sneakers, a lot depends directly on its material. In the event that the top is made of natural or artificial leather or suede, then they crack at the fold or simply wipe.

Glue or sew on patches of much thinner and more elastic material than the top, such as suede or artificial leather, on cracked and bursting places.

Important! But it is better not to allow the formation of cracks. To do this, lubricate genuine leather shoe cream, clean suede with a dry stiff brush, as well as a school washing gum, try to raise the pile.

In order to clean genuine leather and suede from dirt, it is better to use a slightly damp cloth and under no circumstances wash them. running water. By the way, try not to wear shoes that are made of artificial leather during sub-zero temperature.

How to sew on patches?

In those moments when the threads that fasten the details of the sneakers are torn, the layer of threads is restored using the previous holes. You can use a paper clip to pull the threads, but it is best to use a needle from a syringe, slightly dulling its tip on the emery so that the needle cannot cut the thread.

Important! Remember that the care of boots, sneakers, boots and sandals must be correct even in the season when you do not wear them. This is what will become the key to the strength and durability of both the upper and the sole. Save it to your bookmarks and use ours as needed.

Even the most expensive and high-quality shoes tend to tear and wear out over time. If the sole has come off in your favorite pair, do not rush to contact the shoemaker or take the shoes to the trash. Most likely, you will be able to solve the problem on your own.

What kind of glue to glue shoes

Today there are many varieties of shoe glue. So you can glue the sole of the shoe using the well-known "Moment", rubber glue, epoxy, nairite, etc. Each type of glue has certain properties that you need to know in order to purchase exactly the glue that you need.

The first thing you need to know is that you should not use the so-called " Super Moment". When it hardens, it becomes very hard, which will contribute to the appearance of cracks and fractures on the sole.

As for the rubber adhesive, it is more suitable for secondary work, such as gluing the insole and pre-fixing the sole. It is not recommended to use it for basic work due to its low adhesive ability.

Strong fastening of the sole will be provided by such types of glue as polyurethane glue and special compound"EVA (ethyl vinyl acetate)". In favor of the latter, we can say that it does not absorb moisture and remains elastic even after drying. The only difference between them is that "EVA" is not suitable for products made of PVC, while polyurethane adhesive can be used to glue a wide variety of materials together.

Do-it-yourself shoe sole repair

Getting Started self-repair shoe soles, you need to prepare: acetone, a retractable knife, glue, cleaning agent, newspaper, a clean rag, sandpaper and a brush. In order to glue the sole of the shoe, you need to perform the following steps:

1. Wash the surface of the sole well with inside and degrease it with acetone or alcohol. For degreasing, you can use 70% alcohol.
2. Wait for complete drying.
3. Thoroughly sand the surfaces to be bonded with medium grit sandpaper.
4. Apply the adhesive, carefully filling all small cracks and depressions with a special spatula, spatula or brush. If necessary, after a while, apply another layer of glue.
5. Connect and press the areas to be glued together (it is the pressing force that is important, and not the duration, as is commonly believed).
6. If necessary, remove excess adhesive that could damage appearance shoes with a cleaning agent.
7. Place a small dumbbell inside the shoe or provide another method of weighting. The main thing is that during the time the glue dries, the selected weighting agents do not leave creases on the shoes.
8. Leave the shoes in this position for a couple of days in a warm, dry room.

I also suggest you watch a video with a pretty detailed description the whole process.

First part:

Second part:

As you can see, the process of gluing the sole is quite simple and does not require special skills and abilities. However, if you doubt that you will be able to glue the sole with your own hands, or if you are afraid of completely ruining your favorite pair, it is better to contact the workshop.

Unfortunately, any footwear is not eternal: either the heels of the boots will be erased, or the sneakers will tear, or the sole will burst. Many in such cases immediately go to the repair shop, but you can fix these problems yourself at home. To do this, you need to know some tricks with which you can restore your favorite shoes or boots.

How to properly seal a broken sole?

Even if it burst across the entire width, it can be fixed. There are several ways to do this.

Method number 1.

Step back from the crack about 5 cm towards the heel and draw a line parallel to it with a marker. From the drawn line to the toe of the boot, clean the sole with sandpaper. If there is a protector, it is necessary to clean it off “to zero”. Attention: if you have berets or shoes with a tread greater than 5 mm, then try the second option, this method It won't help you.

After cleaning and degreasing the crack itself with gasoline or acetone, glue it with a good second glue. After that, draw the markings for future thread grooves, as is done in the figure.

Using a shoe knife, cut small grooves along this marking. Remove the insoles from the boot and sew the sole along the cut grooves with strong threads. Apply an adhesive over the threads, and when it dries, cover the cleaned and degreased sole with micropore or other sole material, the thickness of which should be equal to the thickness of the tread and rubber, which was removed with sandpaper.

Method #2.

Clean up inner surface cracks and degrease it. With a shoe knife, cut the edges of the sole to a depth of 1 mm, retreating approximately 5 mm in both directions. Measure the depth of the cracked rubber with a ruler and add another 1.5 cm to this value. Cut out a rectangle from the bicycle chamber, the length of which corresponds to the length of the crack itself, and the width is the resulting value in millimeters.

Clean this strip and degrease, coat with glue on all sides so that the entire surface is covered on one side, and on the other, leave the edges dry - about 5 mm. Bend the cracked sole so that the defect opens up. Treat it with glue and let it dry a little, preventing the edges of the crack from sticking together.

Glue the smeared rubber strip into the bursting place, straighten it.

In these ways, you can easily repair cracked boots, shoes or boots yourself.

How to glue sneakers on the toe?

If the sneakers are a little "leaky" - they are worn out on the socks, you can try to glue them too. It is necessary to act according to simple instructions:

1. Treat the place of thinning with sandpaper and another 2 cm away from the defect.
2. Degrease with any solvent.
3. From polyurethane or ordinary rubber, cut a piece that will be identical in shape to the damaged area. It should have a different thickness: it should be maximum at the site of the largest damage, and its thin part should be adjacent to the sole with a normal thickness.
4. Treat its cut with sandpaper from the side where it will be sealed trouble spot.
5. Treat the patch and the damaged area with glue.
6. With great force, press them and leave the sneakers under pressure for 24 hours.

After simple manipulations, you can repair your favorite sneakers and continue to enjoy their convenience.

How to fix a hole in the sole of a shoe?

If the hole in the sole is small, then it can be effectively sealed with ordinary glue-sealant. For these purposes better fit silicone. Cut off its nose so that it fits perfectly into the hole of boots, shoes or any other shoe that needs repair.

From the inside (under the insole), press the area of ​​the hole with a piece of leather, plastic or other material. Fix up with the sole part. Squeeze sealant into the hole so that it completely fills it. After drying, it firmly merges with rubber, due to which the hole is reliably eliminated and you can not be afraid of wet feet.

If it is large enough (appeared as a result of wear), then it can be sealed with a special polyurethane shoe using thick super glue. Such parts are sold in shoe stores.

What's the best shoe glue?

Professional shoemakers agree that polyurethane glue is best suited for sealing broken, worn and other defective shoes. It has good elasticity, strength and provides a high degree of attachment, which allows you to restore any cracked shoes. In addition, adhesive and special shoe composition, which can be purchased in specialized stores, do an excellent job with such tasks.

If the boot is cracked, frayed, or another “misfortune” happened to it, you don’t need to rush to the shoe shop, but you can try to repair it yourself.

It must be said right away: when solving the problem of how to glue a cracked shoe sole, you should at the same time tune in to buying a new pair. At home quality repair impossible to carry out. The sole is subjected to constant stress, and even the most durable state-of-the-art products will not be able to provide insulation for the foot for a long time.

When repairing in the factory, the repair of the sole is carried out using a replacement. Very often, during this process, shoes lose their shape, and their appearance becomes unpresentable. If it is not possible to purchase a new pair, or until shoe store there is nothing to reach, you have to think about how to glue the bursting sole of the shoe.

We get rid of the hole on our own

How to glue the soles of winter or autumn shoes? Moment glue, Crazy Hands epoxy sealant, Desmokol polyurethane agent are suitable as an improvised tool. Each glue is accompanied by instructions that you need to focus on when working.

It should also be borne in mind that these agents are toxic. In case of contact with mucous membranes, they must be immediately washed off with a stream of running water.

Work algorithm:

• Since winter or autumn shoes in most cases have honeycomb soles, you will first have to deal with honeycombs. The rubber that covers them will have to be removed to such an area to remove all the accumulated dirt from the holes. Sometimes access to the cells is carried out from the side of the insole, which, when cleaning the holes, has to be completely removed;
• Honeycombs need to be covered with small scraps of micropores and filled with silicone sealant, sealing well;
• Before sealing a broken sole, you will need to wait for the sealant to dry and harden;
• Next, a piece of rubber or micropore is cut out, which enters the hole - if it is voluminous, or small holes are pressed in with a mixture of micropore sawdust and sealant;
• According to the size of the shoe, the sole is cut out of thin rubber, glued with the help of an already prepared adhesive over the entire area of ​​\u200b\u200bthe shoe;
• Put boots or boots under the press.

How long it takes the glue to dry completely is indicated in the instructions.

How to seal a hole in the sole of summer shoes? You should act according to the same algorithm, only there will be less hassle.

If the sandals are glued, then it is better to purchase a rubber sole from the workshop and glue it on your own with rubber glue. This can be done when the shoe has a solid base. Sometimes soles are attached to light summer shoes only along the contour. In this case, the sandals will have to be thrown away.

Sports shoe repair

How to seal the sole on sneakers when a hole appeared in them due to the fact that they stepped on something sharp? If the training process takes place in the gym, you won’t have to give up your favorite pair of sneakers.

Of domestic adhesives, it is best to use epoxy, designed specifically for shoes. Its cost is low.

The edges of the hole in the sole must be carefully cleaned and degreased with a solvent. When everything dries, apply a properly diluted epoxy.

If the hole is large, it is necessary to put a fiberglass mesh into it - it is called a sickle. While the glue dries, it is better to seal the place of the hole from the outside with masking tape - so that the sole remains even.

The ideal adhesive is the American Seamgrip adhesive. They stick rubber boats. If you manage to get it, you won't have to part with your favorite pair of sneakers for a long time. This is the only adhesive that completely solves the problem than sticking rubber or polyurethane soles.

But if there is an opportunity to purchase glue of this brand, then there will hardly be money to buy shoes. Its cost is quite high.

Imported epoxy mixtures of the Done Deal type are better than domestic adhesives, but the durability of sneakers when using them cannot be promised.

How to fix a torn skate sole? It all depends on the material from which the skate sole is made and the location of the hole.

Cheap skates are fixed almost on cardboard, and any epoxy glue will help to cope with the problem if the hole in the sole is not where the blades are attached. In this case, the shoes will have to be thrown away. Torque will reduce all efforts to zero.

You will have to do the same with expensive skates - even the most expensive glue cannot provide a strong fixation of the blades after repair.

You can still try to seal holes on the side of the boots or on the toe yourself, but a deformed boot does not guarantee stability. home renovation sports shoes should be carried out only in case of minor damage.

Expensive skates with leather soles are glued with a special shoe glue for repairing leather products. If the place to be glued is thoroughly degreased, the hole is filled with a mixture of leather scraps, pressed in, then the integrity of the sole will be restored.

When repairing expensive sports shoes, it makes sense to purchase expensive glue. High-quality sports shoes are much more expensive than packaging with adhesive.

How to glue the sole, cracked across, at the shoe, you should not even think about it. At home, it is impossible to cope with the repair. Yes, and you should not trust private shoemakers who promise to solve the problem by installing prevention. After such a repair, you only manage to reach the door of the shoe shop. When repairing, a complete replacement of “spare parts” is required.

The nuances of work

In order for the shoes to last for some more time, you need to know the following nuances repair:

• all surfaces before applying the adhesive are cleaned and degreased, thoroughly dried;
• the adhesive is applied in a layer no more than 3 mm thick;
• before connecting the parts, the glue is kept for about 10 minutes;
• shoes must lie under the load for at least 10 hours.

The load must be selected so that the shoes are not deformed. If there is a shoe block available, you won’t have to worry about the shape of your favorite boots or shoes.