Diagram of a baby crib with dimensions. Do-it-yourself children's bunk bed: drawings, diagrams, photos

Parents strive to give their children the very best. In shops and markets, prices are rising all the time. This applies to any product, including furniture. Adults are forced to save a lot. They often have to arrange housing on your own. A do-it-yourself baby bed will cost less than bought in furniture showroom. Making a cozy bed for a baby is easy. This is done in a couple of days. Here you need to have a desire to work.

Children grow up fast and furniture is quite expensive.

To make a bed with your own hands, you need boards and beams made of wood that is poorly absorbed by moisture, such as pine or oak. First, two pairs of legs are made. For the headboard, the supports should be longer, since the back is higher here. This is necessary in order to be able to raise the pillow higher and lie reclining in bed, for example, while reading. Usually a do-it-yourself baby bed is made using the following materials:

• bars;
• plywood;
• boards;
• PVA glue;
• stains;
• varnish.

In an ordinary crib, a child can sleep for three, maximum four years.

Natural wood does not emit harmful substances, so babies do not have allergic reactions. Such furniture is reliable, durable and looks good. A well-made bed is the key to a comfortable sleep. If the room is small, the product is made in such a way that during the day it serves as an arena for games. The size is taken based on the length and width of the mattress.

The bed should be as comfortable and functional as possible.

Usually they do not make it with their own hands, but buy it in a store. Children's mattresses, as a rule, are developed together with orthopedists. Here special attention is paid proper formation of the spine, and also take into account the needs of the child's body in obtaining a healthy and full sleep.

In fact, a do-it-yourself bed for a child is made “on time”, you can do it.

Children from 4 years old buy a mattress for spring block, where the individual elements are united by a metal frame. On it, the weight of a sleeping child is evenly distributed over the entire area of ​​\u200b\u200bthe product. For infants it is better to use mattresses without springs, consisting of foam rubber. In the baby's bedroom, it is advisable to install the bed away from the window opening. This will ensure that the child is not blown by a draft.

To make a crib with your own hands, you do not need any professional skills, and the process will take a maximum of 3-4 days.

A chandelier should not hang above the child's sleeping place. Bulbs often burn out. Sometimes it happens that when the lamp fails, its glass scatters in different directions. A glass shard can easily injure a child. If there is a book shelf hanging over the baby, make sure that it is nailed to the wall firmly enough.

The main thing is to use only high-quality materials and carefully consider the whole process from start to finish.

Basic details of wooden beds

Although wooden products for babies are expensive, but individual parts can be purchased at an affordable price. It is advisable to carefully grind the purchased blanks with your own hands so that the child does not get hurt on some protruding chip. The product consists of the following parts:

• frame;
• lamellas;
• sidewalls;
• backs;
• legs.

As a result, both the child and the baby himself will be satisfied.

The frame is made of planed and well-polished boards. The slats that support the mattress from below consist of slats. They are inserted into the grooves cut in the frame and form a lattice for mattress ventilation. The distance between them is about 5 centimeters. The sidewalls serve as a fence, thanks to which the child will not fall down. The supporting backs are filled with plywood sheets.

But if the baby has a large physique, the parameters of the blanks can be changed upwards.

To support the mattress in the frame, special grooves are cut. Carpentry glue is applied to the slatted ends. The rails are inserted into the holes. For a more secure fixation, outer side screws are screwed in. The backs are made using vertical bars connected by crossbars. Next, plywood or wooden rods are installed.

In furniture stores there are a huge variety of models of beds for different ages.

The rear and front sides are filled with slats, fixed with glue. The near side is made one third lower than the far side. This makes it easier to take care of your baby. The holes in the cross bars are filled with PVA glue. Then the wooden rods of the fence are inserted there. Parts should fit tightly into each other, without any backlash. Square need to check the correctness of the angles. All angles must be 90 degrees. The assembled sidewalls are placed on a flat surface until the glue dries completely.

But the first factor in choosing a crib for a child should be the material from which the piece of furniture is made.

Required tool

If you poured a lot of adhesive into the grooves, some of it will, of course, come out. There is nothing to worry about here, since in the dried state the glue is easily cut off with a knife. Next, the remaining panels are attached, which will serve as the headboard and footboard. They are screwed to the sides with countersunk screws. Each screw must be fully sunk so that their heads are not palpable. Later, these recesses are covered with putty and polished. During operation, the following tool is used:

• saw on wood;
• manual frezer;
• Sander;
• corner;
• screwdriver.

If necessary, we clean the shields over the entire surface.

After the bed is assembled, it must be decorated. To do this, all the gaps between the connected parts are covered with putty. When the putty is completely dry, the treated areas are sanded with fine sandpaper. Further, the assembled structure is processed with a stain. This will protect the tree from negative impact moisture. After the stain has dried, a layer of varnish is applied. Since the furniture is intended for the baby, all impregnations must be natural, not containing toxic and aggressive substances.

The only downside wooden furniture, sold in most stores - this is a "sky-high" cost.

During assembly work, the fixing screws should be screwed in as far as possible so that they are completely recessed. The resulting recesses are later closed with plugs or smeared with putty. The assembled structure must be strengthened with special corners. Next, the finished product is varnished or waxed for wood. If you decide to add wheels to the crib, then do not forget to make clamps for them.

A do-it-yourself baby bed will cost parents a maximum of 17 thousand.

Advantages of handmade children's furniture

If the baby's room has small size, the crib can be made with drawers. It is convenient to store toys, bedding and clothes of the child in them. Such functional furniture saves space, eliminates the need to clutter up the room with additional cabinets or chests of drawers. The advantages of a do-it-yourself baby bed are:

• the ability to design a model that fits perfectly into the interior of the room;
• confidence in the quality and reliability of the product;
• the possibility of using only materials that are safe for health;
• relatively low cost.

Independent design and manufacture of a crib has advantages over buying a finished product in a furniture store

When all the details and working tools are prepared, it is necessary to carefully consider the very process of making the bed. Such work is best done outside the home, as there will be a lot of sawdust and dust. If it is not possible to work outside, indoor furniture should be covered plastic wrap and remove the carpet from the floor. For a small room, you can make a bed, sleeping place which is on the second floor. Below, instead of a bed, a soft carpet is laid on the floor. This option will be convenient if you have only one child.

The best option is two large drawers so that you can put large toys and bedding in them.

On the first floor, the kid will spend time playing, and on the second tier, climb the stairs for relaxation. Usually the process of lifting to the second floor gives children great pleasure. If the child likes to draw, you can put a small table and chair on the ground floor. For two children, the usual bunk bed. Structurally, such products are designed in different ways. The lower floor can be exactly under the upper tier, or located perpendicularly.

For beauty, the crib can be opened with a primer and varnish.

Sometimes steps are also used as lids for drawers underneath. In each such box you can put children's toys, linen, clothes. Before you start making a bunk bed, you need to decide on the place where it will stand. You also need to decide on which side it is better to mount the stairs to the second floor. If the room has a low ceiling, the top tier should not be very high.

After you decide on the size and appearance of the bed for the child, view photos of popular models on the Internet and find the necessary drawings, you can start making the royal bed for the baby

The closer to the ceiling the child is, the more stuffy air he will have to breathe. On the other hand, it is advisable to take into account that an adult should not rest his head on the second tier when he sits down to the baby. The height of the first tier is associated with the convenience of sitting on the bed, as well as the fact that you can build a drawer for bed linen below. Relying on this information, we can conclude what dimensions the furniture to be constructed should have. The most popular baby cot options are as follows:

• transformer;
• sliding;
• one-story;
• bunk;
• rocking chair.

In order for the dimensions of the mattress and the crib to match, it is better to first buy a mattress, and only after that proceed to the drawings of the crib.

transformer in daytime usually folds up, thereby freeing up space in the room. For such a model, a special frame is attached to the wall, where the folded product is removed. So that the visible front of the bed fits into general style rooms, it should be decorated. The sliding bed is made of two parts. As the child grows, it can be lengthened. For this, special wheels are located at the bottom. A two-tier model is most often made for two children.

From the tools you will need a drill, a jigsaw and a grinder.

Conditions for the manufacture of bed parts

If you purchased wood material directly from the sawmill, then before proceeding with the manufacture of parts, the bars and boards need to be kept for about a week in the room in which the manufactured furniture will be located. This is necessary so that the humidity of the room is equal to the humidity of the materials. Otherwise, in the future, some places of the bed may crack or warp. When the material acquires the desired parameters, boards and bars must be planed and carefully sanded.

All materials can be easily purchased at a hardware store.

The vertical bars of the bed should be of such a height that it is possible to build sides and backs above the upper sunbed. The front side of the lower tier is most often made removable. The cot guard is an important safety feature. Its reliability should be given special attention. Fencing boards to the support bars are screwed with self-tapping screws with inside. Hats must be fully screwed into the tree. During the manufacture of the fence, you need to leave an opening for the steps.

For small room a similar version of a crib with a second floor is perfect, but there will be no first floor.

Stairs are usually made strictly vertical or inclined. First, two beams are attached, which will play the role of guides. Then the steps are screwed with screws. The top step and the ladder itself are attached to the bed with long bolts. After the fence and steps are installed, plywood sheets are laid on which the mattresses will be located. Because all the details this product fastened with screws and bolts, then it is easy to disassemble and move to another place.

This process usually gives children a lot of pleasure, and sleeping on the second floor is much more interesting.

Such a bunk bed is very durable and reliably serves for more than one year. If you paint it beautifully, and then cover it with matte nitro varnish, it will not shine with sun glare and will retain the naturalness of the drawings for a long time. The inside of the sides can be trimmed soft cloth, which will protect the baby from drafts and bruises.

If a child goes to school, or just likes to draw a lot, a place under the bed can be equipped with a desk.

Thus, even in a small children's room there will be more space for games and other entertainment.

VIDEO: DIY crib.

Making furniture with your own hands is not as difficult as it might seem at first glance.

A do-it-yourself baby bed will cost much less than a finished counterpart from a store.

Anyone with minimal knowledge and skills can collect even enough complex structure, if guided by a detailed description of the upcoming work.

And for starters, you can try to make a baby bed for your child. Moreover, its device does not differ in complexity.

Figure 1. The design of the bed provides for roomy drawers for linen and small sides.

Experienced parents are well aware of the fact that proper crib for the baby - this is a guarantee not only of his calm and comfortable sleep, but also of harmonious development. As a rule, children sleep much more time than adults. And if the dimensions of your apartment are small, then such furniture can serve not only as a place to relax, but also replace the arena.

You can make a bed with your own hands in just a few days. In this design, you can provide for all the nuances that are necessary for your child. How the bed should look approximately is shown in Figure 1. The diagram will help you assemble the cradle for the baby quickly and efficiently.

Design calculation and materials

To make truly high-quality children's furniture with your own hands, you need to consider a few mandatory points:

1. Assembly materials must be used exclusively environmentally friendly. Solid wood or plywood is best. Do not take MDF and chipboard. The products that were used for sizing can cause allergies in the baby.
2. Be sure to provide for the presence of protective bumpers, which should be equipped with any children's furniture. They will not let the child fall when he tosses and turns in his sleep.
3. The dimensions of the children's bed should be no less than 150 × 60 cm, but no more than 180 × 70 cm. The child will quickly grow out of a smaller design, and it will be uncomfortable for him to be too large.
4. At the bottom of the bed, you need to provide drawers in which you can store bed linen, diapers, diapers and other accessories, necessary for the child. So you can save usable area in the apartment.

You can buy a lattice base ready-made or get by with a sheet of plywood.

These conditions are not always observed by manufacturers of children's furniture, so it is not easy to choose a finished product in a store. In addition, if you assemble the bed with your own hands, you can significantly save the family budget. Since the most significant expense item will be the purchase of an orthopedic mattress.

It is wiser to purchase it in advance and, based on the existing dimensions, calculate the dimensions of the future cradle. In addition, you can buy a slatted plastic base for the bed. It is inexpensive, but you can get by with a sheet of ordinary plywood. As long as the weight of the child is insignificant and the base of the furniture under him will not spring, you can not pay special attention to maintaining his flexibility.

In addition to the above items, you will need the following materials:

• furniture board(it is advisable to choose non-resinous wood, for example, linden) 200 × 60 × 2.8 cm in size - 2 sheets;
• plywood sheet;
• aluminum mounting brackets;
• self-tapping fasteners of different lengths and diameters;
• wheels for drawers (d = 4.5 cm).

When everything you need is purchased, you can start making the bed.

Back to index

Bed making

Furniture ties and a special drill are required to assemble the parts.

On the furniture board with a simple slate pencil, mark the required dimensions. If holes are provided in the sides of the bed, then they can be drawn with the help of improvised objects, for example, by circling a bouillon cup or a glass of suitable diameter around the edge.

Cutting furniture panels and plywood can be ordered when purchasing them, if you already have ready-made dimensions and patterns for the shape of blanks. So you can avoid dusty and dirty work in the apartment.

A jigsaw will help to cut the workpiece quickly and accurately, but if it is not available, you can get by with a simple hacksaw. In order for the wood fibers to be less ridden, the cut points must be sealed with masking paper tape. Thanks to this simple reception of garbage and sawdust, there will be much less.

All wooden details already at this stage, it is necessary to carefully sand and sand so that an accidental splinter cannot damage the baby's skin.

If the cut is sealed with paper tape, the fibers are less lifted.

If you do not have ready-made mounting brackets, they can be cut from an ordinary aluminum profile. The size of the element depends on the planned dimensions of the furniture. The length of the corner should be equal to the length of the side headboard. Make holes in the fasteners for self-tapping screws. It is best to use zinkovka. With it, the holes for the fasteners will turn out neater, and the fastening itself will be more reliable.

With the help of the corners of the sidewall of the bed, they are attached with their inner side to the mattress lattice (or a sheet of plywood that replaces it). On each side, the structure is pulled together with 6-8 self-tapping screws.

After the blanks are fastened on one side, the bed must be carefully turned over on its side, and the walls and bottom must be fixed on the other side. Be sure to check the correct position of all elements relative to each other. Do not allow distortions and displacement of workpieces, otherwise the entire bed will turn out to be very unstable and unreliable.

The walls are fixed to each other with furniture ties. To make holes for them, you can use a special drill. It makes the job much faster and easier.

Back to index

Product headboard

After the furniture frame is fully assembled, you need to make a back-headboard. You can do without this design detail, but its presence will help to avoid the following problems:

The shape of the head of the bed can be any.

1. Children's injuries. In a dream, the child often tosses and turns and raises his head above the pillow. If the side of the bed is low enough (less than 10 cm in height), then it can inadvertently touch it. And this does not contribute to a restful sleep for either the baby or his parents.
2. Throwing bedding out of bed. Children often throw pillows and blankets on the floor. For them, this is a game, and parents have to not only lift things, but also change bed linen.
3. Lack of psychological comfort. If the head of the bed is low, then the child feels unprotected. This can lead to sleep disturbance.

Therefore, it is more reasonable to make a headboard. To do this, you will need another furniture board. The headboard can serve not only to protect furniture, but also decorate it. Carved backs always look beautiful and neat, bringing a folk touch to the whole interior. The bed will look more organic if the headboard is repeated with the same detail at the feet of the product, only smaller.

The legs for the bed are screwed from the bottom with long self-tapping screws.

The windows in the backs can carry not only a decorative function. Due to this solution, the headboard can be attached to the bed frame so that the screw heads are not visible.

All details are carefully ground and polished. Special attention it is necessary to pay attention to the cutouts and slots in the backs, because the child can stick his hand into them and inadvertently get hurt. It is best to carry out this work with the help of grinder or similar drill attachment. So you can achieve a perfectly smooth surface.

Finished backs are fixed on the body with long self-tapping screws. If you want to make hidden fasteners from the slots in the headboard, then drill them from the bottom up. Holes are made carefully so as not to damage the workpiece. The place for the screed will have to be done manually, because the window is unlikely to allow drilling a hole with a drill. But if you use enough to make a bed softwood, then there should be no problem.

Now it is fashionable to make furniture at home on your own, and every year the number of home craftsmen is increasing. Someone prefers to purchase blanks and assemble them from them necessary furniture while others do their own work from start to finish. A homemade bed can be very simple or with intricate shapes and patterns. It's not just a matter of skill and availability of equipment - personal preferences and financial capabilities play an important role. In this article we will tell you how to make a bed with your own hands from various materials.

In order for the product to please and to be used for a long time, you need to approach the matter very responsibly, realizing the limits of your capabilities. It is necessary to choose a suitable model and, taking into account the material used, prepare a tool.

Required Tools

Depending on which material is selected, certain tools will be required to work with it.

For working with metal

• Electric welding machine.
• Bulgarian.
• File.
• Metal brush.
• Electric drill.
• Roulette.

To work with wood

• Electric jigsaw. If the product is made of boards, you can get by with a hacksaw for wood.
• Screwdriver.
• Electric drill.
• Roulette.
• Building corner.
• Pencil.
• Plane.
• Chisel.
• Grinder.

As for consumables, we will talk about this separately, considering this or that model.

Material selection

Bed materials:

1. Metal corner.
2. Profile or round pipe.
3. An array of wood.
4. Plywood.

The above materials can be used either individually or in combination. So, a metal bed can be equipped with wooden backs, and a plywood product is assembled on a frame made of timber. There can be many options, and you can figure it out in more detail by reading the article.

Location

The first step is to clearly determine what the dimensions of the future bed will be, taking into account its location. It is possible that you are modernizing the bedroom, changing its design, then you can move away from the usual bed placement patterns and find a new place for it. If so, here are a few tips to help you.

• Do not install the bed with the headboard to the window opening, as if the window is open, there will be a draft, and the head can be blown out.
• If you place the bed with the headboard towards the doorway, then it will not be possible to see who enters the bedroom.
• It is better not to hang a chandelier over the bed. It can break loose and fall on a person lying in bed.
• In uninsulated houses, the outer walls are very cold, so it is better not to put the bed in such places.
• A shelf not securely nailed to the wall above your head can also cause a lot of trouble.
• AT narrow bedroom the bed located in the center of the room will not allow you to move freely. In addition, this arrangement can cause discomfort.
• Many people leave a place for a laptop at the head of the bed. Note that this "time thief" will deprive you of many hours of good rest in this case.

It may seem that there is no room for a bed in the bedroom at all, but this is not so. We only gave recommendations, and you decide for yourself how relevant they are in your case.

Wooden bed

Don't let the apparent simplicity of the design fool you. You need to tune in to the fact that you have to work hard to make a bed out of solid wood. If you are determined, then there is every chance to do something original, while saving money. It is quite natural that it is not easy to decide on the design of the bed right away, so first look at some photos of wood products.

Photo of wooden beds

Having chosen the product you like, you can find a similar drawing on the Internet or draw it yourself, taking into account the dimensions of the room and personal preferences. Often, home craftsmen take a drawing of a bed and remake it for themselves, removing or adding something.

From array

If you are not going to sleep on boards, then when planning the size of the bed, you need to take into account the dimensions of the mattress. If it has not yet been purchased, then you need to take care of this in advance or find out on selling sites standard sizes and build on that data. If you plan to make a bed of non-standard sizes, it is important to know that the mattress will have to be made according to custom order.

A custom-made mattress will cost a little more.

It is clear that in a relatively small article it will not be possible to describe the manufacture of several wooden beds, and we are not striving for this. Based on the example given, it will be possible to understand how to assemble a bed from an array.

Let's look at an example of making a wooden bed for a 200 × 160 cm mattress, if there is a minimum of tools - only the most necessary ones.

The actual dimensions of the mattress often differ from those declared by the manufacturer, and to a smaller extent. Having purchased a mattress, measure it, and then adjust the dimensions of the manufactured bed to fit it.

If there is no drawing with a bed suitable for the size of the mattress, then you can take any one you like as a basis, redoing it to fit your size. If the design is very simple, then you can draw a sketch yourself.

Let's say that after checking the dimensions of the mattress, it turned out that its length and width are one centimeter less than the declared ones - 199 × 159 cm. You will need the following material:

• Bar 50 × 40 mm, length 209 cm - 19 pcs.
• Planed board 22 × 100 mm, length 159.5 cm - 18 pcs.
• PVA glue (furniture).
• Self-tapping screws 41 and 65 mm.

Having a clear idea of ​​the quantity and size of the required material, you can go to the store for it.

Making a frame

You can assemble the frame on the floor or on four stools.

So, we need to make a rectangle with internal dimensions of 200x160 cm, which corresponds to the dimensions of the mattress + 1 cm of tolerance. Each side of the frame will consist of three bars assembled into a single structure.

• Of 19 pcs. purchased timber 40 × 50 mm, you need to choose 4 pcs. the most even and with a minimum number of knots.
• For further work you need to cut off the excess at a right angle. With sufficient skills, you can mark the beam, and then, using a building corner, draw a cut line. If you cannot cut evenly with a hacksaw along the line, then it is better to use a miter box.
• You should get 2 bars of 160 cm each and 2 bars of 208 cm each (internal size of the length of the bed 200 cm + 2 bars of 4 cm each).
• The cleanest side of the bars will be used as the front (top of the bed), so we will lay the bars down with this side.
• You will need 4 more bars with the same dimensions. You also need to cut 2 bars of 200 cm each, and 2 bars of 168 cm each (internal size of the width of the bed 160 cm + 2 bars of 4 cm each).
• To make the frame strong corner connections you need to overlap, so for the second row, bars of a different size are used, which we sawed out last.
• Glue is applied to the bars of the first layer, and then the bars of the second row are laid and attracted with self-tapping screws. Excess glue must be removed immediately, otherwise it will interfere with the work on grinding the surface.
• Now the bars of the third row are attached in the same way.

• It is necessary to check that the corners of the bed are assembled at an angle of 90˚. To do this, we measure the dimensions of the assembled frame diagonally - they should be the same.
• After the glue dries, you can continue to work.
• Since our mattress is 159 cm wide, this size is quite large - the boards we use can sag. To exclude this, in the center of the bed, from one back to the other, from below, you need to make a stiffener. For its manufacture, you will need 2 bars 2 m long each. They are also fastened together and installed in the same plane with the bottom of the bed. This is clearly visible in the photo.

The bed being made has 4 legs located at the corners, but for safety, you can set the fifth point of support in the center - then the base will definitely not bend.

• The legs will be made from two bars 40 × 50 mm, fastened to each other. Their height is selected according to the preference of the owner in such a way that they will be attached to the bottom two bars.
• Having glued and fixed the legs with screws, we wait until the glue dries, and only after that we turn the bed over to the position in which it will now be constantly located.

• To make the base for the mattress along the sidewalls of the bed frame, you need to fix the remaining beam 50 × 40 mm (or existing trimmings), since the boards will be attached to it. The lower edge of the upper beam of the frame will serve as a guide.
• The width of the inner part of our product is 160 cm, therefore, in order to avoid squeaking, the boards can be made 5 millimeters shorter - 159.5 cm (or a little less).

• After sanding the boards, you need to lay them on the frame so that they do not touch the sides of the walls of the frame, and fix them.
• Since the self-tapping screws will be screwed in from the edge of the board, holes will need to be drilled under them in each board, using a thin drill for this.
• As for the distance between the boards, we find it empirically. In our case, the length of the inner part of the bed is 200 cm. We retreat 5 mm from the edges. It remains 199 cm. Divide by 16 (the number of boards). 199/16 \u003d 12.44 cm. Round it up, and it turns out that you need to mark the support beam every 12.4 cm. Since the width of the board is 10 cm, the gap between them will be 2.4 cm, which completely suits us.

• If you need to get a greater distance between the boards, then you need to reduce their number and again perform the calculations according to the scheme we have given.
• Now we need to sand the whole structure. To do this, it is better to take the bed outside the room, as there will be a lot of dust.
• It is convenient to use a grinder or a drill with a nozzle on which an emery cloth is attached. After mechanized processing, you need to complete the process manually using fine-grained emery cloth.

• The bed must be primed and varnished in several steps, each layer is applied after the previous layer has dried. The job is best done with a spray gun. AT last resort, you can use a brush, but it is important to understand that the appearance of the applied coating will not be the same as when using a spray gun.

You probably noticed that we still have 3 boards left. Of these, we will make the back, as in the photo.

The height of the backrest is 45 cm, and the width is 170 cm, but this does not matter, since it will not be integral with the bed - we will fix it on the wall at the level with the mattress.

Its manufacture is not at all difficult. Three boards are sawn off at 170 cm each. We make 11 boards of 45 cm each from scraps. If there are not enough boards of 45 cm each, then 2 boards of 40–42 cm can be screwed through one board. Just like the bed, the back needs to be given a presentable look by varnishing it.

The backrest can be hung on hooks, only in this case it will knock against the wall. More practical - rigidly fix the back to the wall. Now wooden bed you can use.

Video: making a wooden bed

Chipboard bed: step by step instructions

The manufacture of structures from chipboard may seem very difficult, due to the nature of this material. If you cut, grind and glue the edge at home, then some difficulties arise, especially with cutting chipboard, as the decorative layer can be damaged. Many problems can be avoided if you make a drawing in advance and order the manufacture of parts in furniture shop. At home, it remains only to assemble the structure.

This time we will look at the process of making a small single bed with two drawers. Here is an example of cutting standard sheet Chipboard for one bed.

From the remnants of the stove, you can make shelves for books or something else that is needed on the farm.

So, we have a ready-made set of parts that need to be assembled to make a bed.

To do the job, you will need the following tool:

• screwdriver;
• drill (you can use a screwdriver instead);
• jigsaw;
• confirmation drill;
• bit extension;
• bits (cross and hex);
• mallet;
• pencil;
• ruler;
• awl;
• roulette.

You will also need consumables:

• Confirmations - 50 pcs.
• Stickers or plugs for confirmations - 50 pcs.
• Self-tapping screws 3.8 × 45 mm - 15 pcs.
• Self-tapping screws 3.5 × 30 mm - 30 pcs.
• Self-tapping screws 3.5 × 16 mm - 40 pcs.
• Furniture corner - 12 pcs.
• Linear roller - 8 pcs.
• Wide furniture handles - 2 pcs.
• Plastic legs - 12 pcs.
• Bar 20 × 45 mm (3 m) - 3 pcs.

Now let's start assembling.

Since a mattress of 200 × 70 cm will be used, we will adjust the existing slats to the width of the mattress, making them 70 cm long. As a result, there will be 12 of them.

On ten rails on one side, you need to fix the corners.

First, we will make boxes that can be pushed under the bed. Let's assemble the frame first. To do this, lay out the blanks in such a way that the part glued with the edge is at the top. When assembling, it is important not to confuse the sides. Well, if the edge is not glued from the end of the inner part, then you will not mix it up. If the edges of the parts are glued in a circle (which is wrong), then you need to try to fold the box without twisting it, and then attach the bottom. After making sure that everything matches, you can start assembling.

Stepping back from the lower (or upper) edge of about 3 cm, you need to drill a hole with a confirmation drill. This must be done carefully, as one awkward movement - the part will be damaged. The thickness of the laminated chipboard is 16 mm, so we retreat 8 mm from the edge of the workpiece, slightly core and drill a hole without the slightest deviation.

If you have never assembled furniture from chipboard, then first practice on the unused remnants of the sheet.

By connecting the parts, we get such a box.

In order to screw the bottom, eight confirmations are enough - 2 on each side. These drawers are not designed to hold very heavy items because the plastic casters are not designed for that.

It remains to attach the handle and install the rollers. One box is ready, now the second is going in the same sequence.

Putting the finished boxes aside, let's start assembling the bed. Since boxes will be installed on one side, you need to put together 3 parts, using 3 confirmations on each side.

As a result, we get such a "bench".

Now we will assemble a decorative box, thanks to which the mattress will be fixed. This part is not as high as the base of the bed, so 2 confirmations will be used on each side.

We put the resulting frame on the bed frame so that it does not interfere with pulling out the drawers, and connect them together from the inside with 3.5 × 30 mm self-tapping screws.

You need to nail the plastic legs.

Let's start making ribs. On the front of the frame, draw a line from one edge to the other along the height of the bed frame. Now we fix the bars with the corners screwed to them every 13 cm, so that their lower part is lined up.

Instead of ribbed boards, you can use a chipboard cut to size.

After that, it remains to fasten the bars to the opposite sidewall with 30 mm screws.

Having rolled up the boxes and laid the mattress, you can begin to use the bed.

As you can see, with the right approach, it will not be difficult to assemble a bed from chipboard at home. The design can be any size, as in the next video.

Video: making a podium double bed from chipboard

pallet bed

Beds made from pallets are in fashion right now. At first glance, it may seem that this kind of design would be appropriate only in some kind of provincial dacha, but this is not so, because pallet beds can also be found in houses with a rather rich environment.

Let's move from words to deeds. Consider one of the options for assembling a pallet bed. How many will be needed? It all depends on the size and design of the manufactured product. So, a single bed with legs can be made from 2 pallets, and without legs - from 4. We used 8 pallets to make our double bed.

If possible, then you need to choose the most whole pallets. They need to be skinned.

All pallets should be painted with non-toxic wood paint. Since the tree is very hygroscopic, it is likely that the pallets will need to be opened with paint 2-3 times.

If there is such a desire, then you can open the blanks with varnish.

Having laid the first row of pallets, it is necessary to fasten them. If the wood is very strong, then holes are drilled under the screws.

Then the second row is laid.

All pallets are fastened together with metal plates, fixed with wood screws.

Thanks to this simple technology, you can make a pretty decent pallet bed.

You can also make a back from pallets.

From the remains of pallets, you can assemble some furniture and install it near the bed. In general - who likes what.

From plywood

You won’t surprise anyone with a plywood product, but you can make furniture from it at home. We will use sheets of the FSF brand, since not every plywood is suitable for making a bed.

Consider an example of making a bed for a spring mattress 1900 × 900 × 200 mm.

Materials for making a bed

The thickness of the plywood used can be 12, 15 or 18 mm. Thin sheets can be used when fastening plywood with screws. From 18 mm plywood, the bed will be more durable, but very heavy, so it is preferable to use sheets with a thickness of 15 mm - they are much stronger than standard chipboard.

• Plywood 2.44 × 1.22 m - 1 sheet.
• Beam 30 × 40 mm - 2 pcs. by 1.9 m.
• Beam 30 × 40 mm - 7 pcs. by 0.9 m.
• If the edges of the parts need to be pasted over, then purchase PVC edge. Its consumption will be no more than 8 p / m.
• Glue "Moment" - 1 tube.
• Screws 5×40 mm - 26 pcs.
• Screws 5×60 mm - 12 pcs.
• Screws 3×9 mm - 8 pcs.
• Thrust bearings - 4 pcs.

As for the tools, they are the same as for working with chipboard. Wood screws can be used instead of screws.

Side wall back side The beds are large in height. This is done so that the drawers that are pushed under the bed do not rest against the walls. If there are no boxes, then the side walls can be made the same.

Bed making

From the existing plywood sheet, you need to cut out the details corresponding to the drawing.

If desired, laminated plywood can be used. In this case, it is important to consider that it is very difficult to cut such a sheet at home without damaging the laminated coating. In addition, then the edges will necessarily need to be pasted over with a furniture edge.

To cut plywood, you need to use a saw with small tooth, and the jigsaw should be carried out slowly - so we get an even cut without chips. As a result, we should get parts of the following dimensions:

1. Front back - 932 × 650 mm.
2. Backrest - 932 × 500 mm.
3. Facial side panel– 1900×200 mm.
4. The rear side panel is 1900 × 350 mm (if there are no cabinets, then we also make 1900 × 200 mm).

• The ends of all parts must be sanded. To do this, you can use a small wooden block wrapped with medium grit sandpaper.
• After that, we assemble the bed frame.

bed base

• The backrests are attached to the side rails with 5x40mm screws (2 for each front side and 3 for the back).
• Then we fasten the beam to the side rails of the bed using 5 × 40 mm screws (7 pcs per side). The head of the screws should be slightly recessed into the timber. If driven deeper, the screw will go through the plywood.
• We fix the crossbars from the beam on horizontal bars self-tapping screws 5 × 60 mm (1 for each point).
• With 5 × 40 mm screws, we fasten the bars to the backs from the inside (3 screws for each).
• At the last stage, we fasten the thrust bearings from below to the backs - 2 screws 3 × 9 mm for each.
• We install the bed, lay the mattress and use our product.

If instead spring mattress use soft on the frame, then you need to cut the bottom out of plywood and screw it to the bars from above.

As you can see, there is nothing complicated in making a plywood bed.

metal

If you have some welding skills, then you can make a metal bed. We will not even consider the option of a bolted connection, since such a product will loosen very quickly.

Look at the photo of a collapsible metal bunk bed. Agree that she looks very presentable.

For its manufacture, the following materials were needed:

• Profile pipe 50 × 25 mm - 8 m.
• Profile pipe 40 × 40 mm - 8 m.
• Profile pipe 20 × 20 mm (or 15 × 15) - 40 m.

In addition to pipes, a metal primer and hammer paint were purchased.

One of the advantages of such a bed is the absence of bent parts, so a pipe bender is not needed to make it.

If you buy pipes, and not use those that have lain for several years in the garage, then do not opt ​​for rusty ones, since then they will need to be cleaned for a long time.

Frame manufacturing

Since the bed is collapsible, its parts can be made in parts. Let's start with the backs.

• The base will be pipes 40 × 40 mm. We cut them into equal parts of 2 m each. If the ceilings are low, then they can be reduced to 185 cm.
• The width of our backs will be 90 cm, so we will cut off 8 identical segments of 82 cm (90-(4 + 4) = 82) from a 20 × 20 mm pipe, and 8 pipes of 30 cm each.
• So far we will use only half of the prepared material.
• On a flat plane, parallel to each other, you need to lay pipes-racks.
• Stepping back from the bottom 40 cm and from the edge 1 cm, a pipe 82 cm long is attached.
• It is necessary to check the correctness of the set angles with a building corner.
• After 95 cm, the second pipe is grabbed.
• We return to the first one, and on the tacks we assemble the grate - 2 pipes of 30 cm each and a cross member of 82 cm.
• We do the same with the second lattice.
• After checking the angles and alignment of the stuck parts, they can be welded thoroughly.
• The second back is made in the same way.

Now let's start making the shelves.

• We will also cut the profile pipe 50 × 25 mm into 4 equal parts of 2 m each.
• The width of the shelves will be 88 cm, so we need 26 pieces of pipe 20 × 20 mm, 83 cm each (88-(2.5 + 2.5) = 83).
• 2 pipes are laid on the edge parallel to each other.
• We mark 13 cm from the edges and grab one jumper at a time, placing them along the bottom edge.
• We lay out the remaining 11 jumpers every 14 cm and grab them.
• After checking, the shelf is scalded, and the second one is assembled in exactly the same way.
• To the shelf that will be installed at the top, it is necessary to weld a fence of the same height as the height of the lattice on the back. The pipe used for fencing must be bent, not welded at an angle. If there is no pipe bending machine, then it can be filled with sand and bent in a vice or between two supports. This pipe must be welded in the middle of the bed, as in the photo.

• 3 more are welded in the same way vertical racks, but it will not be welded to the back, so you need to weld a small bar from the end.

The turn has come to assemble the structure together, for this we will use welding a little more.

Since our bed is collapsible, we will make universal fasteners for it.

• From a pipe 20 × 20 mm, 16 pieces of 10 cm must be cut off and welded to the backs at the junction.
• Each attachment point uses 2 tubes. They are inserted into the lattice pipe and cling to the back. If this is not done, then it will not be possible to assemble the bed, since the attachment points will not match.
• After checking the correct location of the part, we thoroughly weld the tubes to the back.

• With the help of a grinder, it is necessary to process the welding seams.

Assembly

• Now let's assemble the bed.
• In order for the collapsible parts to hold together securely, they will need to be secured with self-tapping screws (after final assembly).

It is also necessary to make a small ladder, the dimensions of which can be arbitrary.

• We attach it to the shelves with bolts and nuts.

• At the final stage of work, the entire structure is disassembled, degreased, primed and painted.
• After the paint has dried, the bed can be brought into the house and assembled.
• To close the ends of the pipes, specially designed plastic plugs are purchased for this purpose.

If the bed is made for children, then its length can be significantly reduced.

As you can see, at home you can make a beautiful and durable metal bed.

Production of decorative elements

If you want to do something original, then when making a bed, instead of standard profile pipes you can use forging elements.

Such parts are sold in specialized stores or made to order. Good results can be achieved using bent parts, and you can bend them yourself.

Bed legs

A person may have the wrong opinion that the legs of a metal bed will look rough. If you set a goal, then this element can also be made very attractive.

Video: making a metal bed with forging elements

Design choice

The wrong bed can cause a lot of inconvenience. Here are some tips from experts in the field:

1. It is best if the bed is made of natural materials. When using chipboard, plywood, laminate and other materials with synthetic additives (glue, etc.), the products must be certified, intended for the manufacture of furniture.
2. The bed size is great importance. A single bed can be 100, 90 or 80 cm wide, and a double bed can be 200, 180 and 160 cm. If there are no restrictions on the size of the room, then you need to act on the principle - the more the better. The length of the bed must be 20 cm longer than the height of the person (minimum 10 cm).
3. Structures made of chipboard (and laminated chipboard) are the most unreliable and brittle.
4. The solid bottom of the bed does not allow the mattress to ventilate, but too little ribbing can cause the mattress to deform.

Since we are talking about a mattress, there are some nuances of choice here.

1. The mattress should not be hard. It should be soft enough, but not too deformed under the weight of a person lying on it, so it must be selected individually. For a double bed, you can choose 2 mattresses of different elasticity. To make sure that the mattress suits you, you need to lie on it for 15-20 minutes before buying.
2. If a hard mattress is purchased, then you can put a thick mattress topper on it, for the manufacture of which latex or memoriform is used (thickness from 3 to 10 cm). If you have not decided on the choice, then it is better to purchase a mattress with double-sided rigidity.

As for the design features of the bed, this is a matter of personal preference and convenience. AT small room you can place a bed, under which there will be drawers, folding or pulling out from the podium. In a large room, you can give free rein to your imagination by making a wide bed.

Video: how to choose a bed in the bedroom

Single

A single bed is installed in cases where it is planned that only one person will sleep on it, whether it be a child or an adult. Also, 2 or more beds can be installed in one room, for example for two children. Be that as it may, you first need to decide which design is suitable, and then take up manufacturing. Photos of homemade single beds can help with this.

Photos of single beds

double bed

Usually, married couples sleep together (at least for the first few years), and in order for this bed to be comfortable to sleep, you need to take care of its size and design. Look at the photo exhibition of double products.

Photos of double beds

bunk bed

Usually a double bed is made for children. It can be either a simple bed or a fairy-tale castle in which the child will fall asleep with pleasure. When choosing the design of this kind of children's bed, you need to think about both convenience and design.

Video: designing a baby bed

Photos of bunk beds

Drawings and diagrams: bed assembly

Photos: do-it-yourself bed

For a newborn child, the main place of his stay is a crib. Parents try to choose for their own only the best and safest. However, quality items are quite expensive. The price of some imported cribs is prohibitively high. But how to be in such difficult situation? Buy a cheaper model, the quality of which leaves much to be desired?

Remember important rule: saving on the health and well-being of your children is unacceptable!If you do not have the opportunity to buy a solid bed for your child, then a do-it-yourself bed for a newborn is exactly what you need.. Maybe it will be inferior in design to the store analogue, but you can be absolutely sure of the quality of this furniture. A do-it-yourself crib for a newborn, made with love, will become your child's favorite resting place and a source of pride for the whole family for the skillful hands of dad.

Do-it-yourself crib for a newborn - manufacturing technology

This article provides all the necessary information on how to make a do-it-yourself crib for a newborn: drawings, photos and detailed description process. The choice of material is a tricky one. The table below describes the most common types of materials for making a DIY crib.

Material type	Benefits	disadvantages
Wood	Eco-friendly and completely safe material, pleasant to the touch, with excellent aesthetic qualities	High price
MDF	Eco-friendly and safe; affordable; convenient in work; covered with safe paint, looks aesthetically pleasing	Needs a paint finish
Chipboard	Affordable material; practical and aesthetic (coated with laminate or melamine); convenient in work; light in weight	Contains formaldehyde, hazardous to children's health

MDF bed

Chipboard bed

Wooden bed

To begin with, you need to prepare all the necessary tools, materials for the crib and its decoration, accessories and be patient.

Work materials

by the most best material for the manufacture of a crib for a newborn is a tree. This natural resource environmentally friendly, safe, non-allergenic and pleasant to the touch. The best wood for children's furniture recognized beech: It is very durable and aesthetic. Also a good option would be oak, birch, ash and alder. Pine wood is quite soft and may not withstand the active onslaught of children. So, You will need the following consumables:

Tools for the job

In addition to materials, it will be necessary to prepare a set of tools in advance:

• Level gauge and measuring tape;
• Rasp;
• Manual milling machine;
• A hammer;
• Drill and suitable drills;
• Varima;
• Woodworking machine;
• Electric jigsaw.

Now in more detail about how to make a crib for a newborn with your own hands: drawings, photos and instructions will help you figure this out.

We determine the overall dimensions and draw up a drawing

The starting point is the mattress for the crib, or rather its dimensions. Do not spare the money and buy your baby a quality mattress with a "complex filling" made of coconut fiber with layers of latex. regular size children's mattress 1200 x 600 mm. What other children's mattresses are, you will learn from the table below.

Kind of baby mattress	Advantages	disadvantages
With spring frame
With dependent spring block	Affordable; good orthopedic properties; reliable and durable	Over time, it begins to creak; Accumulates dust and insects; springs corrode and accumulate electromagnetic waves
With independent spring block	Increased wear resistance and strength; Hypoallergenic	High price
Springless mattresses (by type of filler)
coconut fiber	moisture resistant; Hypoallergenic; Does not accumulate insects and pests; Possesses average rigidity; Affordable
Latex	Moisture resistant; Eco-friendly and safe; Excellent orthopedic properties; wear resistant	High price
Cotton wool and foam rubber	The most affordable	Accumulate dust, moisture, pests and bacteria; Low wear resistance; Short operational period; Do not have orthopedic properties
polyurethane foam	Non-toxic and harmless; Excellent orthopedic properties; Hypoallergenic and resistant to pests and bacteria; wear resistant; Relatively affordable

spring mattress

Springless mattress

Cotton mattress

The dimensions of the mattress are fundamental to determining the size of the crib. The height of the bed from the floor should be such that the grown-up baby can climb into the crib on his own. It is recommended to make it equal to 350 mm.

The distance between the lattice to the solid wall of the crib is 12 mm, and between the bars - no more than 9 mm. Such indicators guarantee the safety of the baby. Based on these points, you can prepare a schematic drawing, which is much easier to work with.

How to proceed?

Now you have all the necessary components to make an excellent do-it-yourself crib for a newborn: drawings, photos of the model you like, and it's time to start the manufacturing process. First, prepare everything you need for assembly.

We produce materials and carry out the details of the crib

You need to do the following types of work:

• Process with a machine wooden planks, which should be 70 x 35 mm in size;
• To construct the bottom, you will need a beam from which the frame is made. You will also need 6 transverse bars in which you will need to make nests of 25mm in size;
• These recesses can be done both on the machine and with a straight cutter;
• To calculate the back frame, it is required to add the thickness of the side walls multiplied in two and another 25 mm to 600 mm;
• For the bars of the slatted walls of the crib, slats 20 x 20 mm are needed, which are rounded on a milling machine.

Do not forget that this crib is made for a child, so all sharp corners and edges should be rounded and sanded.

Assembly of parts and finishing

When all the details are ready, it's time to put them together:

1. We assemble the back frame with a 35 mm spike;
2. We connect the blanks of the side walls with poles and two backs using deaf spikes;
3. Glue the back to the side walls. After the glue dries, you can connect the parts with self-tapping screws;
4. After all the parts are assembled, the crib can be covered finishing material. Remember that at this stage, the safety of the child comes first. Therefore, all finishing materials must be absolutely harmless to the baby. Choose your primer and paint water based. The varnish layer must always be sanded.

If you choose varnishes, then buy those that have the NC mark. Only such materials are allowed to be used on children's furniture.

How to assemble a crib yourself?

If you decide that a do-it-yourself crib for a newborn is too tough for you and bought it ready-made in the store, then, for sure, upon arrival home you will have a lot of questions about assembling this piece of furniture.

If you are sitting at a loss in front of a pile of details and cannot figure out how to assemble a crib, instructions, photos and recommendations will help you in this matter. In order to correctly assemble all the parts together, you need to perform the following steps:

1. All details must be moved to the children's room. This will save you from moving the already assembled crib. In addition, in this case there will be no question: how to squeeze the bed into the doorway;
2. Unpack the box. Must have inside detailed information about how to assemble a crib, instructions, photos and a list necessary tools. As a rule, this is a screwdriver, a reversible key and a hammer;
3. Check the availability of all parts of the crib according to the list. If something is missing, then immediately contact the seller to replace or return the goods;
4. If suddenly there were no instructions, then you can check the complete set of all parts without it. Be aware that all cribs are standardly composed of the following elements: top and bottom, rubber furniture wheels, supporting structure for the mattress and the mattress itself, two side thin boards. Inspect all parts carefully for defects.;
5. Now let's proceed directly to the assembly of the crib. Screwing the screws should start from the bottom and side backrests. The screws must be tightened loosely. Next, we connect the back wall with 2 screws to the side backs;
6. The next step is the front side of the crib. Most models have this part solid and movable. You need to insert this element into the grooves on the side parts. Next, firmly holding all the fasteners, we check how freely the facade moves;
7. For rocking a baby, arc-shaped components, which are located on the bottom of the side walls, will be useful. When the baby grows up, they will need to be fixed in metal grooves in the sidewalls;
8. Critically evaluate the strength and stability of the entire structure, the strength of the bottom, the absence of sharp corners and material defects ;
9. Next, we put a mattress in the crib and arrange a children's bed according to our own taste.

This simple instruction will help you assemble a new crib bought in a store on your own without involving a specialist.

Assembling the swing bed

The pendulum bed differs from all other analogues in the presence of a baby rocking system. This feature is very convenient for the first months of a baby's life. However, with the configuration of this model, difficulties may arise. But a further description of how to assemble a crib - a pendulum: instructions, photos and step by step guide will help resolve this issue.

This type of bed consists of a frame, bottom, sides, legs and a pendulum mechanism. Also, such models can be equipped with special drawers for clothes and linen crumbs. The mechanism itself can swing up and down. When the need for it disappears, the structure is fixed.

Assembly is carried out according to the following scheme:

1. You will need all the elements of the crib, a work plan, screws, mufflers and a screwdriver;
2. The workplace on the floor should be covered with a light-colored cloth to prevent the loss of elements;
3. We fix the static rear wall with screws to the side backs. To avoid mixing up and down rear wall, be guided by the legs;
4. The next step is the installation of the bed. It can be both solid and rack. The slats are inserted into special holes in the rear wall bar. First, the bed is attached slightly with screws. Movable front component is attached to the recesses on the side backs of the crib, which serve as guides. Next, the screw connection should be tightened more;
5. Further, the finished body can be turned over and the pendulum system can be assembled. If the model has linen boxes, they are placed in the inner space of the pendulum. Further, its side panel is fastened with screws. The body is mounted on the pendulum using bearings. Make sure that the recesses of the clamps exactly match. Screws are closed with plugs for an aesthetic appearance.

A do-it-yourself crib for a newborn, carefully prepared for the baby, or bought in a store that meets all safety requirements, will become the best place rest and sleep of your child and will adequately take a central place in the interior of the children's room. To carry out these manipulations, it is not necessary to call the wizard. Thanks to this guide on how to assemble a crib - a pendulum (instructions, photos and recommendations), you yourself will perfectly cope with this task.

All photos from the article

Natural wood baby cribs for newborns today can be found in any furniture store. However, very often parents prefer to make this piece of furniture on their own: in this way, it will be possible to reduce costs by almost an order of magnitude, and choose the design that will fully meet our needs. And just to create something for your child yourself is very nice.

Naturally, the manufacture of such a crib is a rather complicated process, which should be undertaken only after thorough preparation. So if you have not previously encountered furniture work, we recommend that you carefully study the methodology described in the article.

Materials and tools

Blanks for main parts

Beds for newborns made of natural wood in furniture stores cost a lot, but the materials themselves for their manufacture can be purchased at a very reasonable price. So it turns out that if we have the skill, we can make premium-class furniture, spending about the same amount of money as we would need to buy the simplest bed from MDF or chipboard.

For the manufacture of children's furniture, we will need:

• Edged boards made of coniferous wood (spruce or pine).
• Bars with a section of 30x50 mm for the manufacture of main frames.
• Reiki with a section of 20x20 mm for the manufacture of filling.
• Plywood (optimal thickness is about 5 mm).

Note! For bars and slats, it is best to take the most durable wood, such as beech or oak.

In addition, the work will be impossible without related materials:

• Self-tapping screws (it is best to take phosphated products designed for woodworking).
• Joiner's glue.
• Putty for wood.
• Steel corners for connecting parts.
• Stain or other composition designed to impregnate wood and protect it from moisture.
• Furniture varnish or interior paint.

As for decorating, here you are not limited in your imagination. For this purpose, it is worth using multi-colored ribbons, and textiles (canopy can be made from it), and complex compositions for artificial aging of wood.

In addition, we need a children's mattress. And here it is better not to save money, but to buy an orthopedic product in a specialized store. Of course, the price of such mattresses is quite high, but they really have a beneficial effect on the baby's emerging spine, so we take as high a quality model as the budget allows.

A set of tools for work

Despite the fact that a wooden crib does not differ in complexity of design, we still need carpentry tools to make it. Of course, every master has most of them, but if any of the above is missing, then you should either buy it or rent it.

So, we will need:

• Jigsaw or reciprocating saw for cutting boards and beams.
• Sander.
• Manual milling cutter with a set of nozzles.

Note! If possible, it is better to use a stationary router, but there will be little work for it.

• File for wood.
• Drill and screwdriver.
• Measuring tools (tape measure, level).
• Clamps for gluing workpieces.
• Kisli and rollers for painting, varnishing or decorating.

Crib construction method

Making the basic elements

We assemble the crib

If all operations described in previous section, you did it yourself, then you will not need instructions for assembling the crib - you will already perfectly understand where each part is installed.

So below we will limit ourselves to only general recommendations:

• First, we install the frame for the mattress on the backs. To do this, we attach metal corners to the frame of the side parts, on which we lay the lower support part on top.

Advice! For more reliable fixation, it is worth additionally fixing the frame with through screws, twisted through the crossbars in the backs.

• Then install the far board. It can also be fixed with self-tapping screws, but if you want the structure to contain a minimum of slots, then you should first make sockets for spikes on the side rails in the backs.
• The near side is best made folding. To do this, we install two furniture hinges, to which we attach the frame of the board.
• We fix the board in the closed position with two latches, which we fix outside the crib.

Finishing and decoration

When our natural wood baby crib is ready, it should be decorated.

We carry out the work in the following sequence:

• First, with the help of wood putty, we eliminate all defects and gaps between the parts. We wait until the putty mass dries, after which we carefully grind the leveled areas with an abrasive material with fine grains.
• Then we impregnate all wooden parts with a stain or other compound designed to protect the wood from moisture and decay.

Important! Since we make children's furniture, impregnations should be used as natural as possible, not containing aggressive and toxic substances.

• After the impregnation has dried, either open the crib with varnish, or paint it with latex or acrylic paint selected shade.
• Also, for decoration, you can use the currently popular technologies of craquelure (artificial aging of paint), decoupage (gluing images printed on thin paper under a layer of varnish), etc.

So, the crib for the baby is ready, and we just have to put the previously purchased mattress into it.

Conclusion

Making a crib for newborns from solid wood according to the scheme described above will be possible even for a beginner in carpentry. However, the final result largely depends on your skill and accuracy, so for a more detailed study of the techniques and techniques, we recommend watching the video in this article.