How to open a door lock without a key. How to open an intercom without a key: practical tips for those in need

Each code system can be unlocked by simply entering the desired set of numbers. Home locks are no exception. How to open the intercom "Metakom" without a key? Just like the other - dial a special password. The codes listed in this article work if the installer (or someone from the residents) did not change the system settings of the combination lock or the universal password.

Ways to open the intercom without a key

Any combination lock assumes the ability to open the door without a key. Each of the methods presented here is suitable for certain common Metacom models, so if after the first attempt it was not possible to open the door, proceed to the next method. Try all of the above methods - one of them will definitely work. Note: in all combinations, "B" means the call button, regardless of whether it is indicated on the panel with a letter or a handset icon. Here effective ways, which will tell you how to open Metakom intercom models without a key:

1. With the help of the apartment code. To models of code locks from Metacom, a password is assigned for each apartment number in this house. If you know the code cipher of your apartment, dial it and press the call button.
2. With a generic code. If the installer or other residents of the house did not change it, then the standard combination "1234-B" should be.
3. Press the call button and dial the number of the first apartment in the entrance. (Just look for the floor plate to identify it.) If you did everything right, COD should appear on the display. Dial the combination 5702, and after a couple of seconds the door will open.
4. Dial 65535-B. Enter the universal code and press B-8.
5. Enter the universal code and the combination B-6-B-4568.

The methods listed above are suitable for combination locks with a screen. If you want to figure out how to open a Metakom intercom without a display, use one of these methods:

• enter this code: B-27-B-5702, wait a couple of seconds, and the door will open;
• press B and dial the combination 1-B-4526.

How to hack a Metacom intercom

There are special codes that allow you not only to get inside the building without a key, open the door, but also edit the setting of the intercom itself. For example, you can change the passwords used by the system, delete or bind keys to a specific apartment, change the main entrance code, enter programming mode, learn how to open a Metacom intercom without a key in the user menu. For any action, you need to know the so-called "master code". The default password for Metacom is 1234.

1. Door opening. How to open a Metakom intercom without a key? Find out and enter the universal code, press the call button.
2. Working with keys You can remove or attach "pills" to a specific apartment. To do this, enter 65535-B-master-code-B-B. Then enter the apartment number. To write down the key, enter B-7. If you want to untie all attached chips from the apartment, press B-7-0-111.
3. Changing system passwords. Using the menu of intercoms "Metakom" the adjuster can change the universal code of the intercom. To assign a new master password, enter 65535-B-master-code-B-9-3-new password-B. In the same menu, it is possible to change the apartment code. To do this, you need to know the already installed cipher. You are expected to be the owner of the apartment in order to change passwords. Dial the combination 65535B-master code-B-B-apartment number-B-0-new password-B.
4. Codes for entering the intercom menu. Metacom is equipped with three different catalogs. To enter the standard user menu, enter the combination 65535-B-1234-B-B. Intercom service password: 65535-B-master-code-B. To change Metacom system settings, enter 65535-B- master code -B-9.

How to find out the universal code

Metacom assigns its own password for each apartment in the house - it is a set of four digits. The owners of the apartment are obliged to know it in order to get into the house even without a key or in another emergency. The apartment password is indicated in the agreement with the installer. There are universal codes for intercoms that are not tied to an apartment. By default, the main password for the Metacom intercom is 1234. If someone has already changed it before you, then you can only find out the new password from the service company.

Without knowing the universal access code, you will not be able to:

• change it and set a new master password;
• attach or detach key chips from the apartment;
• change the system settings of the intercom;
• assign a new code for the apartment;
• to program the code lock.

Without a master code, you can:

• open the Metacom intercom without a key;
• enter the user menu.

Video instruction: how to open a combination lock

This short video tutorial gives a simple and clear explanation of how to open the door without a key. In the video, the author unlocks the Metakom model with a display. To use this method, you need to know the number of the first apartment in the entrance. It is very easy to find out - on each porch there is a sign with the numbers of apartments belonging to this part of the building. The photo preview shows which intercom model is used. If you have the same combination lock, then the password from the video should be suitable for opening the door without a key.

Today, more than 95% of entrances are equipped with a security system such as an intercom, and about the same percentage of residents found themselves in front of a locked door without a key.

How to enter the entrance without a key

You can try the following options:

• dial neighbors, or any apartment number. In the second case, introduce yourself as a communal representative, postman or physician;
• wait until one of the tenants opens;
• to find out the code, you can go to the company servicing your home and show them your registration. They will be required to provide you with an access code from the intercom of your entrance;
• it is necessary to press the entrance door as hard as possible, and then sharply pull it towards you;
• remove the piezoelectric element from the lighter and click bringing it to the recess for the key. There is a 5% chance that this method will work;
• bring a stun gun and make a discharge, it is likely that the “brains” of the intercom will perceive this as a standard key operation. Big disadvantage this method is the presence of a stun gun at hand;
• go to the Internet, find a special master code for your intercom and drive it into the phone, after looking at the comments.

Important! Each intercom has a special code set by the manufacturer, knowing which you can open the door without a key. Unless, of course, the installation company changed the master password during installation. If the code has been changed, it will be more problematic to open the door and without entering the system settings, this will not work.

How to open an intercom without a key, using a special code

First you need to know that there is no universal “digital master key”, each manufacturer has their own. Let's analyze the popular brands of protective public access locks.

Vizit (Visit)

Vizit intercoms are represented by a wide variety of models, both for apartment buildings as well as for private property. Due to the wide variety of intercoms of this brand and combinations of codes, they are considered the most difficult to open. When typing the combinations below, it is necessary to take into account that there are models where instead of "*" and "#", "C" and "K" are used.

Easy way to open:

• earlier models "*-#-4-2-3-0" or "1-2-#-3-4-5".
• later models "*- # -4-3-2", or "6-7- # -8-9-0".

We open through the maintenance menu:

• dial "# - 999".
• "1-2-3-4" and wait for a brief high sound signal.
• if you heard a two-tone signal, then try to enter one of the following sequences of numbers: "1-2-3-4-5", "3-5-3-5", "6-7-6-7", "9- 9-9-9", "1-1-6-3-9", or enter them one by one.
• complete the opening "2-pause- # -pause-3-5-3-5".

Metacom (Metakom)

Method #1:

• press "call" and No. of the apartment from which the numbering begins in the entrance (you can find out this information above the entrance door);
• again the “call” button and wait until the message “COD” appears on the screen;
• enter the combination "5-7-0-2".

Method #2:

• first "6-5-5-3-5", then the call button;
• then "1-2-3-4", call and "8".

Method No3:

• dial the combination "1-2-3-4-call";
• then "6-call button-4-5-6-8".

If the door is equipped with model MK-20 M/T and you are going to open the lock without a key, then try one of the combinations:

• "call-2-7-call-5-7-0-2";
• "call button-1-call key-4-5-2-6".

Cyfral CCD (Digital)

Intercom Cyfral CCD-2094:

Method No1 (works if there are apartments with the number 100, 200 - 900 in the entrance):

• "call-100-call-7272", "call-100-call-7273", "call-200-call-7272", "call-200-call-7273";
• if it didn’t work, enter the combination “call -from 100 to 900-call-2323”.

Method #2:

• "0000", then "cod" will be displayed;
• enter one of the combinations: "1-2-3-4-0-0", "1-2-3-4-5-6", "4-5-6-9-9-9" and "call" , the inscription “F0” should be displayed;
• then "6-0-1".

Model Cyfral CCD-2094.1M:

Method #1:

• "0-7-0-5-4".

Method #2:

• "challenge-4-1" or "challenge-1-4-1-0".

Method No3:

• “call-0000”, the screen will show “ON”;
• press button "2". If “OFF” is displayed, the quick access mode is blocked and you will not be able to get inside.

Eltis (Eltis)

The most affordable brand in terms of emergency opening. You can open the entrance with the Eltis intercom without a key using a certain combination:

Option #1:

• "call button-100-call-7-2-7-2";
• "call button-100-call-7-2-7-3";
• "call button-100-call-2-3-2-3".

If combinations with the number 100 did not work, insert numbers from 200 to 900.

Option #2:

• hold “call” for 20 seconds, if 5 numbers flash on the screen, remember them and enter.

Option #3:

• press any number until "CODE" appears;
• enter "1-2-3-4", the screen should display the inscription "FUNC"
• press "1", enter your version of the code and press "2";
• reset the settings "6", exit from the menu "0";
• enter a new code.

Option #4:

• "call-1234-2-1-3-3-123".

Forward (Forward)

This system is produced Russian company. To open Forward coded access control devices without a tablet, you need to enter the code:

• "K-5-5-7-7-9-8-K";
• "2-4-2-7-1-0-1";
• "1-2-3-*-2-4-2-7-1-0-1";
• "K-1-2-3-4".

K is a key, maybe in the form of an image of a key.

rainmann

There are Raikmann locking mechanisms similar in name, which, unlike Rainmann, cannot be opened even if you go to the service menu. The Rainmann CD-2000 and AO-3000 models belong to the class of modern and secure devices, but they can be opened by pressing:

• "key-9-8-7-6-5-4";
• after two short beeps "1-2-3-4-5-6";
• “P” will be displayed, press “8”.

There is another original method to get inside, based on the sensitivity of the touch keyboard to cooling (valid in winter time). Apply snow for 10-20 minutes.

Domoguard

Almost any model of this company can be opened:

• "S-669900-CALL";
• then dial the number 1 unit above the last apartment, then press "Call-7-4";
• “F” will be displayed on the screen, press “0-8-0”.

Factorial

The Factorial settings are almost identical to the Cifral brand, however distinctive feature is a mandatory change of the factory code, but you can try to break through engineering menu. How to get to the entrance with the Factorial system:

• "0-0-0-0-0-0" or "1-2-3-4-5-6";
• "5 (with hold) -180180- call - 4 - call";
• after the door should open.

Marshal (Marshal)

A common intercom model in Russia, designed for apartment buildings, in the absence of a key, try entering the following combinations:

• last apartment number plus one;
• then "K-5-5-5-5" or "K-1-9-5-8".

Lascomex (Lascomex)

How to open the door in the entrance with Lascomex code intercom:

First option:

• "B- No apartment - numbers for the entrance."

Second option:

• "0-K-0-K-0-K-0-K";
• "6-6-6-6";
• "P" appears, enter "8". In a minute the door should open, come in.

Barrier II, 2M

Time-tested intercoms "Barrier" cannot be found in new houses, but in old five and nine-story houses this castle is a frequent occurrence. To open the door with the intercom "Barrier II" and "Barrier 2M", in most cases it is enough to hold a magnet in the area where the key is applied, or dial the code combination: "1-3" or "1-0".

Remember: If you have just moved, try to get as familiar as possible with big amount neighbors, someone will help you get in, and you don’t have to stagnate, racking your brains on how to open the door in the entrance and picking up the code. It is better to use a universal master key to the intercom, having a passport with a residence permit in one of the apartments of this entrance. Well, that's all, you just have to determine the most convenient way for you to open the door.

As you know, in order to set up the intercom, you need to enter the programming mode, for which you need to enter the installer code, i.e. dial a password. Entering the programming mode, the master gets all the rights to change the functions of the entire intercom.

Therefore, intercom manufacturers paid close attention to this part of intercom programming ... But they implemented it in different ways ...

Intercoms for apartment buildings, which have become widespread in Russia, are considered. We deliberately do not give here codes that do not serve to open the door, but for adjustment and which are needed by non-engineers, perhaps for hooligan motives.

Hacking information is provided for the following intercoms:

Barrier II and IIM, 4

VIZIT (various models)

Cyfral (various models)

METAKOM

rainmann

DomoGuard

First of all, the question is: are there special intercom codes for opening doors by special services? The correct answer is: no, there are no such codes in modern intercoms (except for the IIM Barrier). But there is a forgetfulness of engineers who, as a rule, do not change the master passwords during installation.

Hacking intercoms Barrier II and IIM

Remember, these are such old "Soviet" intercoms with mechanical locks and a flat magnetic key? For 2M, there is a non-replaceable opening code - 1013. But they were rare then, and even more so now. In general, these intercoms were opened with 2 magnets, for example, from a disassembled key. You just carry them around the key pad until they work.

Barrier - 4

The same, only without buttons (single-user, designed for front doors with concierges). The key has 3 magnets.

Codes intercom VIZIT

General note: If the keyboard does not have * and #, C and K instead. C - * K - #.

Displayless models with LEDs (SM/M/N 100-200):

If standard settings did not change the code * # 4230 or code 12 # 345 lead to the opening of the intercom.

In freshly installed intercoms, codes * # 423 and 67 # 890 are likely

You can enter the service menu:

#999 - beep 2 times - (master code, default 1234) - beep 1 time. If the code is not correct, it will beep with a two-tone signal. The master code can be 1234, 6767, 3535, 9999, 12345, 0000, 11639.

2 + # + 3535 Doorphone opening.

3 - Programming keys for entry. (Attach key + #, wait for squeak + *).

4 - Erasing keys from memory.

* - Exit the mode.

# - Installation confirmation.

For intercom VISIT BVD-3xx (without display and LEDs), (with right-hand or central location of the tablet)

opening the door - press 1 in the menu.

Does not always work in BVD-34x (with a left-hand receiver)

For them it is specified.

Intercom Codes Cyfral

To open the door try:

a) If there are apartments with numbers 100, 200, 300, 400, etc. in the entrance, then you can try to enter the codes:

call (code 1) call (code 2)

where code 1= "round apartment number" (100...900),

code 2= 2323 or 7272 or 7273.

For other models of intercoms (with the letter "M"), the code is suitable:

"B" 41 "B" 1410. Sometimes it helps to just enter 07054.

Intercom CCD-2094.1M (burning or flashing dash on the display) - dial the code B + 0000 or open immediately, or the service menu (the inscription ON) - then press 2. Or, the inscription OFF - then, alas, the quick access mode is turned off.

Intercom Codes Cyfral CCD-2094M

Code 0000 "B" + pause 2 seconds. The inscription "code" appears. We enter the code 123456+"B" or 456999+"B" (rarely 123400+"B"), pause 2-4 seconds, the inscription "f0". The menu is open. For a quick opening, just press the code 601.

If we want to come regularly, we can write our key into the memory of the Cyfral intercom. We press the bell and hold until the inscription appears, then enter the code 123456 (or code 123400). Got into service mode. In service mode, press 5, then enter the number of an existing apartment, the intercom will write TOUCH, put the key - it is in memory. (For models with flat optical keys, instead of the apartment number, dial 600, insert the key and press call).

Intercom codes Eltis

As a rule, opening codes:

"B" 100 "B" 7273

"B" 100 "B" 2323

But if it does not work, you can try other options from Cyfral.

Intercom codes METAKOM

We press the call, then the number of the first apartment in the entrance, the call again (the "COD" will be displayed), then the code 5702 ... If it doesn't work, then we try the codes: 65535+"B"+1234+"B"+8 or or 1234+ "B"+6+"B"+4568.

Only for intercoms MK-20 M/T codes:

"B"+27+"B"+5702

or "B"+1+"B"+4526

And one more thing about MK-20 M/T intercoms: Their firmware does not and will not have protection against master keys. Even without knowing the service - password, if you bring a blank tablet, the intercom will enter the programming mode automatically!

Rainmann intercom codes

For Rainmann 2000 models and those with a dot on the left of the display.

Key button + 9 8 7 6 5 4. A double squeak should be heard. Then we enter the code 1 2 3 4 5 6, the letter "P" will appear. Entered the menu. Further:

4 - Door lock.

6 - Turn off the intercom.

8 - Open the door.

DomoGuard intercom codes

Long press on "C", it will beep.

Then we quickly enter the code: 669900, + call button + number one more than the last apartment in the entrance. The display should show "F---".

Got on the menu.

Open the door - code 080

Remember new key - code 333

Disable door lock - code 071

Blink intercom hack

The only single-user intercom on the list. It is without a screen, without a keyboard, with a mechanical lock. It is placed in houses with a concierge, so breaking it makes sense only at night. We find false bolts of an unusual shape on the lower section of the panel. These are contacts backup power. When 9 volts are applied to them (and they are just the width of the Krona contacts), the intercom is open.

Intercom code T-Guard

Code "B" + 00000 + "B" B" (the last two presses - quickly!) - the door is open.

Some general notes on hacking intercoms:

In winter, intercoms with a touch keyboard (DomoGuard, Rainmann) are subject to hypothermia. We take a normal lump of snow, and lean against the keyboard. When the display shows "Err"(10-20 minutes), the intercom will unlock the lock.

Many wizards change the installer code (password) from the default one (processor code) to another one. This is usually done so that no one else can change the intercom settings.

Now, to enter the programming mode, you need to dial a new code... The old one has been changed and is no longer valid.

No codes are suitable, what should I do? Calmly. If the intercom has a magnetic lock (not mechanical!), Then we put one foot where the door opens and pull hard on the handle. When jerked, the door opens, but nothing is broken.

For regular visits:

We catch the moment when the intercom door is open and stick several layers of adhesive tape on the magnet. At the same time, we leave a small area of ​​\u200b\u200bthe surface for contact. At first glance, the intercom works as usual, but you just need to pull the door harder and voila, it is open.

Methods for hacking other intercoms are currently being specified.

Codes for intercoms

Our universal key opens the following MODELS of intercoms:

Metacom MK-2003

Metacom MK-20TME4

Metacom M-10

Metacom MK-99.2-TM

CYFRAL CCD-2094.1

CYFRAL-intel

CYFRAL CCD-2094.1M

CYFRAL CCD-20 (approx. 70%-80%)

Cyfral 2094/tc (max 50%)

Factorial DM-20TM

Metacom MK99.2-TM

Raikmann PROEL KDC-1803

Vizit SM-100

VIZIT BVD-N100

Visit BVD-341

Visit BVD-431

Visit BVD-311

Visit BVD-313

Visit BVD-342

Visit BVD-M200

Metacom MK-2003-RF

As you know, in order to set up the intercom, you need to enter the programming mode, for which you need to enter the installer code, i.e. dial a password. Entering the programming mode, the master gets all the rights to change the functions of the entire intercom.

Therefore, intercom manufacturers paid close attention to this part of intercom programming ... But they implemented it in different ways ...

Intercoms for apartment buildings, which have become widespread in Russia, are considered. We deliberately do not give here codes that do not serve to open the door, but for adjustment and which are needed by non-engineers, perhaps for hooligan motives.

Hacking information is provided for the following intercoms:

Barrier II and IIM, 4

VIZIT (various models)

Cyfral (various models)

First of all, the question is: are there special intercom codes for opening doors by special services? The correct answer is: no, there are no such codes in modern intercoms (except for the IIM Barrier). But there is a forgetfulness of engineers who, as a rule, do not change the master passwords during installation.

Hacking intercoms Barrier II and IIM

Remember, these are such old "Soviet" intercoms with mechanical locks and a flat magnetic key? For 2M, there is a non-replaceable opening code - 1013. But they were rare then, and even more so now. In general, these intercoms were opened with 2 magnets, for example, from a disassembled key. You just carry them around the key pad until they work.

Barrier - 4

The same, only without buttons (single-user, designed for front doors with concierges). The key has 3 magnets.

Intercom Codes VIZIT

General note: If the keyboard does not have * and #, C and K instead. C - * K - #.

Displayless models with LEDs (SM/M/N 100-200):

If the standard settings have not been changed, then the code * # 4230 or code 12 # 345 lead to the opening of the intercom.

In freshly installed intercoms, codes * # 423 and 67 # 890 are likely

You can enter the service menu:

#999 - beep 2 times - (master code, default 1234) - beep 1 time. If the code is not correct, it will beep with a two-tone signal. The master code can be 1234, 6767, 3535, 9999, 12345, 0000, 11639.

2 + # + 3535 Doorphone opening.

3 - Programming keys for entry. (Attach key + #, wait for squeak + *).

4 - Erasing keys from memory.

* - Exit the mode.

# - Installation confirmation.

For intercom VISIT BVD-3xx (without display and LEDs), (with right-hand or central location of the tablet)

opening the door - press 1 in the menu.

Does not always work in BVD-34x (with a left-hand receiver)

For them it is specified.

You can use the secret combination that is in every intercom Quite often there is a problem when the keys to the intercom are lost or forgotten, however, there is a way out, this is the input of a special code that was set by the manufacturer of this intercom device. All details below.

Understanding how to open an intercom

An intercom kit is necessary in order to ensure security at the entrance apartment building, since criminals usually wait for the victim in open, unprotected entrances to get into the apartment. Also, the intercom ensures order and cleanliness in the entrance, as it scares away lumpen and outcasts.

Each company producing this product, competing with other companies, strives to secure its device and develops management software that is different from others, naturally, by entering its own combinations of numbers

You need to know that entering a special pin code with mercenary intentions is punishable by law.

Modern intercoms have not only the ability to communicate, record a conversation, but also video surveillance, which gives 100% security. Many intercoms are equipped with a special code so that you can open (if you forgot or lost the key) in emergency situations (unlock), as well as a loud emergency notification system when people are evacuated from the building in case of fire, earthquake and other situations.

When using the intercom, the following instructions should be followed:

1. When leaving the entrance, you must press the button under the screen and wait for the sound signal, only then exit.
2. When entering the entrance, you need to lean the key-chip against the reading panel of the intercom device, when the sound signal (impulse) sounds, you can unlock the front door.
3. After leaving or entering the entrance, you can not help the door close, it will close itself with the help of a hydraulic closer.
4. If you push and help the door close, this can lead to damage to the door closer.

The main components of the intercom are: a company name plate, a call block, a primary power source, an independent switching unit, an independent electromagnetic lock that magnetizes a magnet to the door plate, door closer, call button, apartment blocks, keyboard.

Intercoms are divided into multi-subscriber and low-subscriber, according to technical device, multi-wire and two-wire. In the age of new technologies, there are intercoms that receive and send a signal using Wi-Fi, based on optical fiber.

Do not panic if you do not have the keys to the intercom with you, or it has become demagnetized, the encoding has gone off (recoding and programming is required). You can deceive any intercom using a universal key-chip, which is available to ambulance doctors, police, post office workers (postmen), house management workers, Internet communications (Rostelecom). These keys are made in the form of a special tablet, radio key fobs, a two-pin key and are legally issued to employees of special services.

Method description: how to open a Metakom intercom

Domestic intercom Metacom is used for apartment buildings to protect against unwanted guests. What to do to open the intercom, is it possible at all?

Intercoms are produced by many different companies, both in Russia and around the world. Therefore, they do not have a single (universal) set of necessary numbers

The main thing is not to break the screen, but to make (restore) the lock by entering a combination.

To open a Metacom intercom without a screen, you need to dial a special combination consisting of several numbers and letters. Firstly, press the button responsible for the apartment number - B. Secondly, dial the code 5702.

If the intercom does not open, then you can try to enter the codes:

• 64434;
• 1256;
• 1256;
• 4978.

If the intercom Metacon of the MK-20M / T series, forward or Pro, then you must enter similar combinations or a pin code (B + 27, B + 5702). It takes a very long time to go through all the codes and you can either wait for someone to enter or leave the entrance, or call the neighboring apartment and say that you are a neighbor and forgot the keys. And remember that the use of all fraud with mercenary or robbery intentions is punishable by law.

Example: how to open an intercom Visit

Intercom Visit is one of the most reliable devices and is adapted to such harsh conditions as low and high temperatures, wind, rain. The body of the intercom has an anti-corrosion coating, which ensures reliability.

VIZIT has factory setting 12#345 or *#4230. But recently released models can be opened by entering 67#890 or *#423

The intercom of this model works in a humid climate. The average service life is about 10 years.

Intercom Visit in case of emergency can be opened with a special code, you should log in to its menu and dial #999. After 2 beeps, enter 1234. You need to wait a bit and after a short beep, dial 2#3535.

If, after entering the combination 1234, there was no short signal, but a signal similar to a two-tone or others was heard, then other combinations can be entered:

• 6767;
• 3535;
• 12345;
• 11639.

After the dialed combination, you must enter 2#3535. Actual for the following models: Vizit N-100, Vizit SM-100, Vizit BVD-341, Vizit BVD -313 and others.

How to open a Cyfral intercom

Digital has many models: Digital INTEL, Digital CCD-20.40, Digital CCD-40TS, Digital CCD-2087.2TV, Digital CCD-2087.2T, Digital CCD-2087.2T R, Digital M-10MR, Digital M-10MT, Digital M-20MTV, Digital M-20MZV.

To open the Cyfral intercom, you need to have a special master key or know the password

For a Cyfral intercom of a regular model, for opening without a key, you must enter the following numbering:

• Call + 100 + 2323;
• Call + 200 + 2323;
• Call + 300 + 2323;
• Call + 400 + 2323;
• Call + 500 + 2323;
• Call + 600 + 2323;
• Call + 700 + 2323;
• Call + 800 + 2323;
• Call + 900 + 2323;
• Or choose the following combination Call + number + 2323 or 7272, 7273.

To pick up the code, it takes time, it is better to call a neighbor in the apartment. For the Cyfral M intercom, it is easy to open using the combination Call + 37 or Call + 3792. The Cyfral intercom of the CCD-2094.1M series is opened by the code Call + 0000, after which ON will appear on the display, you must enter 2.

If these operations do not work, then the factory access code was changed by the housing and communal services employees.

If you are with a tenant of this house, then you can get the access code from them if the key has been lost. The intercom of the Cyfral CCD-2094M model can be opened by dialing the combination 0000 + call, after the entered cod will appear on the display. 123456 + call, if it does not work, enter 456999 + call, or 123400 + call, after that f0 appears on the intercom display, then enter 601.

Hacking the intercom model Rainmann (Rainmann) 2000 is possible by entering the combination - key + 987654, after a double intercom signal, enter 123456, after which P appears on the display. The letter P on the display monitor indicates that you have entered the service menu, in which you can carry out control with numbers and program the code with your own hands.

Enter a single number:

• 4 - block and disable the Rainmann intercom;
• 6 - turn off Rainmann;
• 8 - open (the door is demagnetized).

Rainmann CD-2000 and AO-3000. In order to open the 2000th model, you must click on the "key", then enter the code "987654". After that, the intercom will beep and you must enter the numbers "123456". If the engineering menu is available, the “P” icon will appear on the screen. Now, to unlock and open the door - you need to press the number 8

The intercom of any DomoGuard model can be opened by entering the combination C + 669900 + call + enter a number 1 more than the number of the last apartment in the entrance. After typing combinations, F will appear on the intercom display, which will mean access to the service menu. After that, we dial the code 080 to enter a new key 2, 2, 2 into the intercom memory. To disable the door lock - 071.

Instructions: how to open the Eltis intercom

All Eltis intercom models open after entering a special combination, however, if the entered combination does not open the door, then the factory settings have been changed. Intercom Eltis (Eltis) can be opened by entering a universal code that can fool the security device.

You need to press and hold the call key for 20 seconds. For a while, a five-digit code will appear on the display of the equipment. Then this combination will disappear, so you need to remember it. This password will allow you to enter the settings menu

• Call + 973;
• Call + 7456;
• Call + 2323.

With the same combinations, in which the call button is pressed at the beginning, you can open the following types (access intercoms) - Tekhkom, Stroymaster, Marshal, Belsplat (Belsplat), Kamsan, Condor, Lock, Poly, Filman, Polylock, Smartel, Laskomex, Modus, Polis and others.

Intercom code

Intercom brand Factorial different models can be opened without a key by entering a special software access code - 000000 + 123456, 5 + 3453475 + call + 7 + call.

Houses equipped with intercoms are found everywhere, but not many people know how to open them without a key.

The Keyman intercom can be opened by entering - K + 100 + 789, after the signal has sounded, enter 123456. After displaying the Keyman R on the display, which allows you to enter the menu, enter 8. If the intercom has a touch screen, then in winter it can be opened by application of a snowball to the screen, hypothermia can ruin the intercom.

It is also possible to open the device using the piezoelectric element of the lighter, which is applied to the place for the key, but this does not always work and is weak.

Intercom Barrier II, 2M and 4 can be opened by pressing 2 + 4 or 2 + 7. You can also magnetize the place where the key is applied and magnetized with a magnet. In the same way, you can open the Arkades intercom with an empty plastic key.

The intercom Raikmann and Rainmann and Smartel can be opened like this:

• Key + 321654;
• After the beep, enter the numbers 123456;
• When P appears on the display, enter 8 or recode with a shocker or electric shocker, which, with its impulse, can turn off the intercom device.

The Blink intercom is the only audio intercom installed in Belarus, Ukraine, Kazakhstan and you can open it with a D9-0.1, 6F22 battery, which we put in a turnkey place. And the intercom Cron, Pirrs and Safe can be opened using the factory combination 951. The intercom pier 1000 Micro can be opened using the factory access code - 12345678 + K + 1234 or 8310649 + entrance number.

You should know: how to find out the code from the intercom

The intercom is the most reliable device for protecting multi-storey buildings, garages and private houses. The occupants of the building or the owner of the garage must know the password and secret codes for emergency opening of the intercom. This password is used if the intercom key has been lost or forgotten.

If at the entrance you find that there is no key to the intercom, first of all it is better to contact the neighbors

If the key to the intercom is lost and the password has been forgotten, it is not possible to open the door, then you need to call the housing and communal services, service or company, a single service center who installed this intercom device so that the master could unlock combination locks. Remember that unauthorized entry and hacking of the intercom at the entrance of the house in foreign territory is responsible for their actions.

Why is it not worth entering codes and physically trying to open the intercom without a key? There is an instruction where it is written that it is strictly forbidden during the operation of the intercom to cause any mechanical damage to the call unit, handset, electronics unit, electromagnetic lock, opening buttons and intercom housings various items, which can lead to damage to the device or its individual elements.

Mechanical damage also includes wiping with snow, dousing with water, heating with fire, dousing with paint and other solutions, using a magnetic key with an electromagnet, tearing out buttons, repairing the device yourself or coding it.

It is forbidden to independently perform recoding, unlocking or other actions by a person who is not a service employee of the intercom device. Do not pull the door behind you, which can lead to breakage of the hydraulic closer. The closing speed of the entrance door is set by the master, depending on the structural features of the door and the adjusting screws.

How to open an intercom without a key (video)

In conclusion, it is worth noting that it is forbidden to put foreign objects under the door from the inside and outside that prevent the door from closing independently and lead to unauthorized entry of strangers into the territory.