The automatic umbrella broke. Here's what to do if your umbrella breaks

When it rains, people use an umbrella to keep their clothes from getting wet. However, very strong wind or careless handling may deform the product. In this case, there is no need to rush and throw away the broken automatic umbrella, perhaps you can still repair it at home.

You will need

• metal tube with a diameter of 6 mm;
• stainless steel wire;
• tin plate;
• various details from an unnecessary umbrella;
• soldering iron;
• pliers.

Repair steps

1. Grooved spokes are a common cause of vending machine umbrella breakage. In this case, you need to find a metal tube with a diameter of 6 mm, then cut off a small piece about 3 cm. You can use an antenna from a TV or radio for this purpose. The ends of the broken knitting needle need to be straightened, then put on the tube and squeeze the ends with pliers.

2. In case of damage to the tubular rivets at the ends of the spokes, you need to insert a piece of soft stainless steel wire into the hole small size and then twist the ends.

3. If the tape breaks on the automatic umbrella, then you need to replace it. First, unscrew the top plug, then remove the panel and remove the fixing nail from the top knot. After that, you need to remove the entire assembly, open the tube gently substituting your hand under it. You need to be extremely careful, as there is a spring inside that can fly out. Now you need to get the rollers and change the tape.

4. Also common cause automatic umbrella breakdowns are traction, they break at the points of swivel. When all the clutches are loose and off the hooks, you can begin to repair the traction. Take a piece of tinplate and cut out a small 40mm x 12mm plate. Bend the plate lengthwise to make a trough. All broken halves of the rod must be straightened. Now the ends can be tinned and the overlay installed, the damaged area must be soldered along the entire length.

5. It happens that the latch stops working and the umbrella cannot be kept closed. To do this, you need to press the locking tab and bring it closer to the handle. Remove the broken retainer from the stem tube and straighten it straight out, then reinstall it. It is recommended to replace the low-quality metal latch with a new one, since such a breakdown will bother you very often.

• Also read -

Do-it-yourself automatic umbrella repair - video

Umbrella- This is a mechanical device, which is a metal or plastic frame made of knitting needles on a tubular rod equipped with a handle, on which a synthetic waterproof material is stretched. An umbrella is designed to protect a person from sunlight and rain.

The umbrella was invented in China 300 centuries ago to protect from the sun. The umbrella in those days was considered a symbol of power, and only the emperor and those close to him were allowed to use it.

A lot of time has passed since then, and now the umbrella has become a constant companion of any person in Everyday life. The airy design of the umbrella makes it foldable and lightweight, but unstable to strong gusts of wind. Therefore, over time, everyone is faced with a breakdown of the umbrella, after which many simply throw them away.

But in vain, because you can save money and time, since usually umbrella breakdowns are simple and are associated with a rivet falling out or one of the spokes breaking. Therefore, you can repair an umbrella with your own hands using a standard tool and improvised materials in half an hour.

Repair of the articulated joint of the spokes with the rods of the umbrella

The most common failure of the umbrella is the loss of a tubular rivet from the swivel rods and spokes. From the mechanical load in the wind, the edges of the rivet unbend, it falls out and is lost.

Repair by setting as a rivet
paper clip

If the breakdown of the umbrella consists in the loss of a tubular rivet from the hinge, and there are no conditions for repair, then it can be repaired using a paper clip.

To do this, it is enough to pass the bent end of the paper clip through the holes of the knitting needle and thrust, then bend the end of the paper clip, as shown in the photo.

If you have pliers with a wire cutter function at hand, then you can take a piece of wire from a paper clip, bend it on one side into a loop, insert it into the holes and form a loop on the other side. Thus, the wire will reliably perform the function of a rivet and will not tear the fabric of the umbrella dome.

Repair by installing a homemade rivet
from copper wire

This is the most reliable way repair that I've been using lately. The repaired swivel in the umbrella did not have to be repaired again.

The material for the rivet is copper wire for electrical wiring with a diameter of about 1 mm. The wire is selected depending on the diameter of the holes in the rod and the spoke.

Before making a rivet, you need to pass the wire through the hole in the rod and check that it moves easily. If tight, then you need to slightly reduce the diameter with sandpaper.

Next, you need to form the head of the rivet. To do this, the wire is clamped in a vice and by hitting the edges with a small hammer, they are riveted, as shown in the photo. If the end of the wire is not flat, then you need to process it with a file with a fine notch.

When repairing an automatic umbrella, in order to be able to install a rivet, it must be kept in a half-open position, which does not allow the spring, which seeks to open the dome. In this case, use a rope to tie the movable lower clip of the umbrella to the handle, as shown in the photo.

In the next step, you need to bring the knitting needle into the slot of the thrust and insert the prepared wire with the head. Bite off the excess wire with side cutters so that its protruding part is about a millimeter.

At the last step, you need to press the created wire head to the anvil (any massive metal object will do) and flatten the wire with light blows along the edges until the head is formed. Here is the umbrella hinge and repaired.

As practice has shown, although an umbrella is used in wet weather, the copper rivet does not oxidize. If desired, it can be covered, for example, with nail polish.

Instead of copper wire, post nails of the required diameter can be successfully used. Nails are made from soft grades of iron and therefore also riveted well.

Umbrella joint repair with screw connection

The pivot joint of the umbrella frame can be repaired using a screw with a nut with a diameter of 1-2 mm of suitable length.

To do this, you need to align the holes of the parts coaxially, thread the screw through them and screw the nut onto it. If the screw is too long, then after tightening the nut, the protruding part must be removed using side cutters.

Usually, when biting a screw, the thread is deformed, and the screw will not be able to unscrew on its own. But for reliability, it is better to rest the head of the screw on the anvil and rivet its protruding part from the nut with a hammer.

If there is only a screw, but no nut, then you need to shorten its threaded part to desired length and slightly rivet the protruding part.

If at least one rivet fell out of the hinge, then, for sure, the others also weakened. Therefore, in order not to repair the umbrella again in the near future, you need to tap with a hammer, resting on the anvil, all the other rivets.

Repair of spokes and rods of an umbrella

The second reason for the frequency of breakage of umbrellas is the breakage of fiberglass spokes or lugs on the rods.

Broken spoke tip repair

In this umbrella, the end of the tip of the needle broke off at the place where the hole for attaching the fabric of the dome passed. Most likely from hitting the umbrella on a hard surface.

On the left in the photo is a whole tip, and on the right is a broken one. If you have a new needle or tip, it is easiest to replace. But the spare spoke was not available and therefore had to be repaired.

For repair, a hole with a diameter of about 1 mm was drilled in the tip and sharp edges were turned with a file in the place of its breakdown. To avoid fraying the thread at the exit from the hole, it is necessary to chamfer with a larger diameter drill or a knife blade.

Repairing an umbrella with a broken fiberglass spoke

As a rule, the spokes and rods in umbrellas are made of metal, but recently umbrellas with plastic rods and fiberglass knitting needles have begun to appear.

Just such an umbrella got into repair, in which one of the spokes broke off at the point of entry into the rocker of the hinge. The rest of the spoke remained inside the hinge.

In the yoke, the spoke is fixed with the help of its bent edges. To remove the rest of the spoke, you need to slightly bend the petals with a thin blade of a flat screwdriver to the sides.

The broken end of the spoke fluffed up a little, so before fixing it in the yoke, it was smeared with Moment's quick-drying waterproof glue.

After crimping the spokes with petals in the yoke, the umbrella began to look like new. Using the same technology, repairs are made in case of breakage of the needle at the tip.

After the repair, the spoke became a little shorter, but visually, with the open dome of the umbrella, this was imperceptible.

If the fiberglass spoke broke in the middle, then its integrity can be restored using a piece of thin-walled metal tube taken from the telescopic antenna of an old radio. The broken ends of the spokes are lubricated with glue and inserted into the tube so that the junction is in the middle of the tube.

Rod eye repair

If the eyelet in the rod is broken off, then it seems that it is impossible to repair the umbrella without replacing the entire rod. But it's not. With the help of a metal knitting needle from an old umbrella, you can successfully restore the eyelet.

The photo on the left shows a working swivel, and on the right with a broken eye on the rod.

To repair, you need to take a metal knitting needle about ten centimeters long with a hole at the end from an old umbrella and tin it along the entire length with solder using an electric soldering iron.

Next, you need to remove the rivet from the rod and cover inner surface solder pull groove, as shown in the photo. When working with a soldering iron, it is necessary to exclude the contact of heated parts and its tip with the fabric of the umbrella dome, since the synthetic material may melt.

In the next step, you need to place a spoke in the groove of the thrust and heat it with a soldering iron along its entire length until the solder melts both on the spoke and in the groove of the thrust. In this case, one must not forget, and correctly orient the hole on the spoke. Using this technology, it is possible to successfully repair broken rods in the middle.

After installing the rivets using one of the technologies described above, the repair of the umbrella can be considered complete.

Umbrella hat repair

Rarely, but it happens that the decorative hat, mounted on top of the umbrella dome, breaks off or unscrews and is lost.

A cap that has broken off from the threaded part, if present, is easy to repair by restoring its integrity.

To do this, you need to drill a hole in the center in the threaded part of the cap remaining in the cane of the umbrella, with a diameter equal to inner diameter self-tapping threads.

In the center of the cap, you also need to drill a hole with a diameter equal to the external thread of the self-tapping screw. Pass a self-tapping screw through the hat and grease it so that it does not unscrew with any waterproof glue and screw it into an umbrella.

The photograph shows an assembled umbrella repaired by oneself using the technology described above. The fabric of the dome is now securely fixed and water will not get on the frame parts.

If the hat is unscrewed and lost, then you can restore it with a self-tapping screw with a large press washer.

To do this, you need to make a cork from wood. A shortened furniture dowel can fit in diameter, as shown in the photo.

At the next step, a hole is drilled in the center in the cork with a diameter equal to the inner diameter of the self-tapping screw.

It remains only to lubricate the thread of the self-tapping screw with waterproof glue and screw it into the cork. As you can see, it turned out beautifully.

If a self-tapping screw with a wide hat is not available, then it can be made from a sheet of plastic suitable color cut out a round washer and fasten it to the dome. The washer can be made from any cork from plastic bottle by removing the threaded part.

About the repair of automatic umbrellas

Repair of automatic umbrellas is not considered in the article, since it is very laborious and home master without experience of repair is not possible. It is necessary to completely detach the dome material from metal structure, remove the upper clip, get to the roller and replace the tape. When assembling, a special tool is required to compress a fairly powerful spring. Therefore, if the opening mechanism in the automatic umbrella fails, then it is better to contact the workshop or buy a new umbrella, leaving the broken one for spare parts.

So, it is not at all necessary to buy a new umbrella, you can repair an existing one. The weather is sometimes unpredictable, and seemingly drizzling rain can turn into a torrential downpour with gusts of wind that can make the umbrella unusable. When you finally get home, prepare everything you need to repair the umbrella. Rummage through the bins and you will surely find a couple of broken and long abandoned umbrellas, the details of which can be used.

Spokes - frequent breakage

As practice shows, grooved spokes are the most frequent breakdown in modern umbrellas today.

For repairs, you need to take a metal tube with a diameter of 6 mm and cut off a piece about 3 cm long from it. The tube can be a knitting needle from another umbrella, an antenna from an old TV or radio. We straighten the broken spoke of our umbrella, put our "new" prepared knitting needle on top of it and clamp it with pliers. Next, you need to put on the umbrella cover and try to open and close the umbrella several times. If the spoke does not fall out, then you did everything right and you can go out into the street in the pouring rain.

Damaged needle ends

There are also cases when the tips on the knitting needles themselves break off and the material stops holding, exposing the knitting needle. This can be dangerous for both you and those around you. The needle is thin enough and can damage the clothes of someone around or scratch, which is even worse. So, for repairs, you need to take stainless steel wire, thread it into the knitting needle, then pull the fabric and twist it into a ball.

Get very original. The main thing is to twist the wire as tight as possible so that the homemade tip does not fly out under a gust of wind or from the constant opening and closing of the umbrella.

Replacing the automatic umbrella tape

The design of such umbrellas provides for a tape that can break off. But, it's not scary either. It can be repaired. To do this, unscrew the top plug of the umbrella, remove the canvas and remove the fixing nail from the top assembly. Next, you should disassemble the entire assembly by placing your hand to the open tube and removing it with great care. You need to be very careful and careful, as there is a rather tight spring inside, which can suddenly fly out and hit you in the hand. After the operations, we take out the roller and change the broken tape.

Traction failure

A fairly common breakdown is the failure of the thrust at the point of their hinged connection. It is worth remembering that it is possible to start repairing such a node only after loosening all connections and removing the hooks. Otherwise, you risk injury or injure someone who is nearby. We cut out a small plate about 4 * 1.2 cm in size from a piece of tinned tin and bend it along the length, thereby obtaining a small trough.

See if one of the halves of the rod is deformed. In case of deformation, it is necessary to carefully straighten it. Next, you need to tin the ends and install the overlay and do not forget to solder the repaired area along the entire length. That's it, you're done.

Retainer repair

In modern umbrellas, there is often a breakdown of the latch, which ceases to hold the umbrella closed. This problem can also be fixed. To do this, press the locking protrusion and with a sharp movement move it towards the handle. Next, you need to get the bent latch, carefully straighten it and install it back. However, if the retainer is made of metal Bad quality, this repair will not save for a long time.

It is better to replace the latch. To do this, again, rummage in the pantry, maybe there was an old umbrella lying around with a broken needle, but with a whole latch. As described above, disassemble and remove the latch and transfer to your favorite umbrella. Next, we assemble the structure in its original form and test it. The mechanism must work properly.

As seen, repair your favorite umbrella is quite real. True, for this you need to have some skills. Not every lady will be able to cope with the task. Most people do not want to waste time and run to the shops for brand new umbrellas. However, choosing a good umbrella that will not break after two or three outings in the rain is also not very good. simple task as it may seem. However, this is a completely different story that requires separate consideration. Repairing a broken umbrella in this case will not be the most difficult way out.

Answer:

Repair of the automatic umbrella device

During the rainy season, the most relevant accessory is, of course, an umbrella. But everyone knows the eternal problem of even the most expensive umbrellas: they break easily, and even a strong gust of wind can disable them. The biggest trouble is if the automatic umbrella breaks down, although it is a simple, but still, mechanism.

Knowing the repair is much easier:

1. Actually a pen, with a button built into it.
2. Three expanding iron tubes.
3. The lower support for the spokes, in which the wheel for the cord is installed and a thin rail that connects the support to the handle.
4. The upper support for the knitting needles, into which a wide pipe is mounted with a screw and a cord is attached to it.
5. Plastic pipe. It is inserted into the top support. In the upper part it has a thickening and a wheel.
6. Cord. With the help of a shuttle, it is attached to the handle, and the button releases it.

The weakest point of an umbrella is the spokes. If the problem is in them, then you need to take a thin tube three centimeters long, and then straighten the broken knitting needle at the ends, put the tube on them and fix it. Take a metal tube.

If the rivet at the end of the spoke is broken, then it is better to wrap it with soft wire, otherwise the fabric of the umbrella will tear.

It is very time-consuming to repair the automatic umbrella device, for example, if the tape breaks, then it must be replaced. We remove the cork, which is located at the top, then the fabric, and pull out the fixing nail from the knot. Then we take out the entire assembly and carefully open the tube. Do it carefully, otherwise the spring will pop out, which then can not be inserted. We take out the roller, change the tape, collect everything in the reverse order.

If the rod is broken, then you need to repair it only after you loosen all the connections and remove them from the hooks. The repair process is not easy, and here you need a soldering iron to repair the device of the automatic machine umbrella. So, we take tinned tin and make a trough out of it, about 40x12 millimeters in size. It must be installed at the site of damage and soldered along the entire length.

A broken latch is repaired as follows: press the protrusion that blocks the mechanism and move it to the handle. We take it out of the tube, straighten it and mount it back.

Often the product does not allow you to repair the machine's umbrella device, since a circuit is needed. But if you managed to get it (and this is not a problem in the information age), then you will succeed, because the process, although long, is not particularly difficult. In general, if you handle the umbrella carefully, you will not have to repair it.

Also you can see video Do-it-yourself semi-automatic umbrella repair

An umbrella serves as an indispensable accessory in rainy weather, protecting from water and wind. If, after another bad weather, it has lost its attractiveness or one of its main parts has broken, do not despair and do not rush to throw it away. It can always be fixed! Before repairing an umbrella, study its device, determine whether it is possible to repair a faulty spare part. Sometimes for automatic designs, the help of a specialist may be needed.

Types of umbrellas

There are varieties of designs and differences between folding mechanisms from each other. The most important part of any umbrella is the dome, which consists of metal frame or plastic knitting needles, on which the fabric and a solid or folding handle are stretched. Each model can be equipped with a simple or automatic mechanism. All umbrellas are conditionally divided into:

• canes- have an enlarged dome of thick fabric, strong handle;
• folding- structures have a telescopic device, can be folded - reduced in size (from two to five times).

Depending on the opening mechanism, there is a division into the following types:

• mechanical- open and close by hand, there are no buttons on the handle;
• semi-automatic- open manually, the automatic mechanism closes the dome when you press the button, and the handle stem folds by hand;
• automatic- the button opens the dome, and you need to close it with your hand;
• full automatic- a button is used to open and close, no effort is needed.

Device

AT different models designs differ, but there are basic details for all umbrellas. Main elements:

• fabric stretched over the frame;
• a rod consisting of telescopic parts of the tube;
• handle, with or without button;
• lower support for spokes;
• upper supports to which the main dome is attached;
• springs (thick short and thin long);
• to the top plastic tube(holder) has a built-in wheel that fixes the lower supports.

The most common malfunction is when automatic umbrellas lose their rigidity. This happens when the wind turns them inside out, bending the thin needles. It is important to periodically check the joints of the knitting needles and, if necessary, strengthen the weakened fabric. For all umbrellas, a single rule applies: the fewer connections on the rod and spokes, the less often the structure breaks.

Spare parts

No matter how expensive and high-quality an umbrella is, it cannot be insured against breakage. Before you throw away your old one and buy a new one, try repairing your umbrella. If you have a second - unnecessary copy - then it can become a source of improvised materials for recovery. Urgent repair of umbrellas, if necessary, can be performed professional craftsmen in specialized modern institutions like the House of Life.

The following components are subject to replacement and repair:

• telescopic the stem or base of a cane;
• knitting needles from different material;
• pen any configuration;
• dome material;
• safety spoke tips;
• central cap;
• buttons.

Do-it-yourself umbrella repair

Depending on the cause of the malfunction, prepare the right materials and support tools. This can be a finished part from an old umbrella, round-nose pliers, wire, or a tool for soldering metal parts. At home, you can repair the automatic umbrella with your own hands, eliminate the following breakdowns:

• damaged fabric at the seam;
• flying tip of the knitting needle;
• bent and broken spokes;
• bad latch.

Fabric repair

To connect the seam on the dome, select the threads of the appropriate color: carefully, manually, sew up the fabric. If the material has come off the end of the needle, then wrap the edge with a thin fishing line and fix it with a knot. Pass the ends of the fishing line through the hole in the knitting needle and fasten it to several knots. This procedure is performed with a free location of the fabric on the frame.

spoke repair

How to repair an umbrella if the spokes are damaged? Follow step by step instructions:

• First, detach the fabric from the frame of the product, remembering the location of the material.
• Next, you need to straighten the damaged knitting needles. If the part is unusable, it must be replaced. Use a soldering iron for fastening or fix the metal parts of the knitting needle with wire (you can use a piece of paper clip).
• Upon completion of work, fix the material with a fishing line to the frame.

Holder repair

If the umbrella does not hold in open form- try to fix the product yourself. Such a breakdown is easily eliminated if the latch is bent. To do this, press the protrusion and sharply move the part to the side. This way the latch tab is taken out and gently straightened. Install it back the same way. Please note: if spare parts for umbrellas are of poor quality, then such repairs will not last long. In this case, you just need to replace the damaged part. It can be taken out of an old umbrella and inserted into the handle.

Automatic umbrella repair

Repairing an automatic umbrella is a little more difficult than a mechanical one, and it takes more time. Sometimes failure is associated with misapplication products, then the parts are severely deformed and they can only be replaced with new ones. If the machine itself is faulty, it is better to contact the masters in specialized institutions where umbrellas are repaired. This process is carried out in a short time.

Where to repair an umbrella

Repair of damaged products of any complexity is carried out by specialized workshops or stores that provide repair of shoes and clothes. AT major cities, such as Moscow, St. Petersburg, work service centres providing quality repair umbrellas. AT small towns There are also centers where the service will cost even cheaper. Pay attention to ads on the Internet, in newspapers, read reviews, customer recommendations, compare prices.