What does a solid red line on the road mean. What does the red marking on the road mean?

The markings in the form of triangles adjacent to each other, directed by the vertices towards the approaching transport, indicate the place where the driver, if necessary, must stop, giving way to vehicles moving along the crossed road. 1.14.1, 1.14.2 Broad lines parallel to the axis of the carriageway - indicate crosswalk; marking 1.14.2 with arrows indicates the direction of movement of pedestrians. 1.15 Parallel broken lines perpendicular to the axis of the road, in which the length of the strokes is equal to the intervals between them - indicate the boundaries of the section of the carriageway in places where the cycle path crosses carriageway. C. Other markup. 1.16.1 - 1.16.3 Wide parallel or broken lines, enclosed in a contour, indicate sections of the road to which entry is prohibited, namely: 1.16.1 - breaks in the median strip, reserve zones, safety islands, etc.

Road markings in red

Allows you to stop at this marking for boarding and disembarking passengers, but without interfering with the movement of route Vehicle. 1.18 Indicates the direction of movement in the lane at the intersection, duplicates the signs of special requirements 5.15.1, 5.15.2 "Direction of movement along the lanes." With a permissive marking, “Turn left” from the leftmost lane allows a U-turn. 1.19 Warns of the narrowing of the roadway. About the completion of an additional lane in the middle of the road or an acceleration lane.
1.20 Warns that at the nearest intersection of carriageways there will be either a “Give way” marking or a priority sign 2.4 “Give way” priority sign 2.5 "Movement without stopping is prohibited" 1.22 Indicates numbers of roads, routes.

Detected blocking ads on the site

Attention

A dashed line whose stroke is equal to the spacing between strokes. 1.8 Broad dashed road markings - indicates the boundary between the acceleration or deceleration lane and the main lane of the carriageway. At crossroads, road crossings at different levels, in the area of ​​bus stops, etc. 1.9 A double dashed road marking line that marks the boundaries of traffic lanes on which reverse control is carried out, separates traffic flows in opposite directions (when reverse traffic lights are turned off) on roads where reverse control is carried out. 1.10 Yellow intermittent road markings. Prohibits parking of cars, duplicates prohibition sign 3.28 "Parking prohibited".

It is applied at the edge of the carriageway or along the top of the curb.

What does the red stripe on the roads of Yalta mean?

Graphic symbols are one way to control movement. Consider what the red markings on the road oblige drivers to do. Types The main purpose of marking on the roadway is to communicate information about the separation of lanes, limit the "islands" of safety, rules and zones for parking, overtaking, and also the distribution of traffic.

Important

Graphic markings can act separately or be duplicated by the corresponding road signs. According to the application method, there are vertical and horizontal markings. Broken and solid lines, arrows, pictograms, as well as their combinations act as markings.

Vertical markings, represented by a combination of white and black stripes, indicate the dimensions of road structures for visual orientation. In some cases, in addition to coloring, a noise effect is used to attract the attention of the driver.

Exam traffic rules

It became known why red stripes were applied to the roads of Astana

The "crown" drawn at the edge of the carriageway means specially designated places for stopping taxis and route vehicles. If road markings are not clearly visible or their meaning is inconsistent established signs, the driver must be guided by the value road signs. Paradox As we can see, none of the paragraphs contains red horizontal markings.
But then what should the driver do if there is a marking, but there are no rules? The only sensible answer to such a paradox is subjective perception. colors. In other words, the red color you perceive is orange from the point of view of the traffic authorities. Red horizontal road markings do exist.
This color is used to indicate temporary markings in Austria, Switzerland.

Road markings full description.

Arrows with a curved shaft warn of the approach: 1.19 a) - to the narrowing of the carriageway in combination with signs 1.18.1 - 1.18.3; 1.19 b) - to a section of the road where the number of lanes for traffic in this direction is reduced; 1.19 c) - to marking lines 1.1.1 a) and 1.11 a) separating traffic flows of opposite directions. 1.20 A triangle whose base is parallel to the marking 1.13 and the apex is directed towards the approaching transport - warns of approaching the marking 1.13. 1.21 The inscription "STOP" - warns of approaching the marking 1.12 (stop line), when it is used with the sign 2.2. 1.22 An inscription consisting of letters and / or numbers - indicates the number of the road (route). 1.23 The inscription "BUS" - indicates the lane intended for the movement of route vehicles, as well as their stops. 1.24 The inscription "TAXI" - indicates the taxi rank.

Don't yawn on the road, two stripes, and you've got it!

Info

Marking 1.14.1 and 1.14.2 is applied on a red background in populated areas at pedestrian crossings raised above carriageway, and outside settlements - at pedestrian crossings located after transverse noise lanes. It is forbidden to enter the marking 1.28 if the prohibition signal is turned on in the traffic light or if a traffic jam has formed in the direction of travel, as a result of which the driver will be forced to stop at this marking. The markings that replace the main markings in places (on sections of roads) where work is carried out are orange.

Member actions traffic in relation to the requirements of horizontal markings. It is forbidden to cross lines 1.1.1 and 1.3 (as an exception, line 1.1.1 can only be crossed if it marks the right edge of the carriageway for the withdrawal of the vehicle from the carriageway during a forced stop).

Yellow markings on the road - what does it mean

General technical requirements The application of road markings establishes certain modes and procedures for the movement of vehicles and pedestrians. Road markings are a means of visual orientation for drivers and are used both independently and in combination with other means in order to improve the safety of traffic organization, increase the speed of vehicles and bandwidth roads. Petroleum polymer resins - used in paint used for road markings.

• Road marking and its characteristics.

  Annex 2 to the Rules of the Road;

• What is more important, a road sign or markings? Priority of signs and markings.
• Website about road markings

1. Edward N. Hines (1870-1938)
2. Douglas V.

road markings

In the first case, it can be used in combination with signs 1.5.1-1.5.3; 1.20 - warns about approaching the markup 1.13; 1.21 (“STOP” inscription) - warns of approaching marking 1.12, if it is used in combination with sign 2.2; 1.22 - warns of approaching the place of installation of the device for the forced reduction of the speed of vehicles; 1.23 - shows the number of the road (route); 1.24 - indicates a lane intended for the movement of block vehicles only; 1.25 - duplicates the image of the sign 1.32; 1.26 - duplicates the image of the sign 1.39; 1.27 - duplicates the image of sign 3.29; 1.28 - duplicates the image of the sign 5.38; 1.29 - indicates a path for cyclists; 1.30 - indicates the parking lot of vehicles that transport disabled people or on which a identification mark"Disabled person". Lines 1.1 and 1.3 are not allowed to be crossed.

Road markings of the Russian Federation set by the rules of the road. Complies with the Vienna Convention on Road Signs and Signals.

Story

For the first time, road markings in Russia began to be used in June 1933 in Moscow: in order to organize traffic, they began to apply nitro-paint with safety lines, called “shuts-lines”. The first marking was applied on the roadway on Teatralnaya Square, as well as on the intersections of Petrovka Street and Neglinnaya Street with the Kuznetsky Bridge. Within two years, markings began to be used in other cities of the country. Until the 1960s, there was no clear unified legislative framework, regulating the application of markings, until uniform traffic rules were introduced in the USSR. In 1975, the first GOST, based on international agreements, concerning road markings was issued.

Active road markings

The last changes to the rules were made on June 30, 2015. Road markings comply with GOST R 51256-99 and GOST R 52289-2004. Modern road markings are of two types.

Horizontal marking

Horizontal markings (lines, arrows, inscriptions and other signs on the carriageway) establish certain modes and traffic order or contain other information for road users. Horizontal markings can be permanent or temporary. Permanent markings are white, except for lines 1.4, 1.10 and 1.17 yellow color, temporary - orange color.

1.1		Separates traffic flows of opposite directions and marks the boundaries of traffic lanes in dangerous places on the roads; indicates the boundaries of the carriageway to which entry is prohibited; indicates the boundaries of parking spaces for vehicles.
1.2.1		(solid line) - indicates the edge of the carriageway.
1.2.2		(Dashed line, in which the length of the strokes is 2 times shorter than the gaps between them) - indicates the edge of the carriageway on two-lane roads.
1.3		Separates traffic flows of opposite directions on roads with four lanes or more.
1.4		Indicates places where stopping is prohibited. It is used alone or in combination with the sign 3.27 and is applied at the edge of the carriageway or along the top of the curb.
1.5		Separates traffic flows of opposite directions on roads with two or three lanes; indicates the boundaries of traffic lanes in the presence of two or more lanes intended for movement in one direction.
1.6		(Approach line - a dashed line, in which the length of the strokes is 3 times the gaps between them) - warns of approaching markings 1.1 or 1.11, which separates traffic flows of opposite or passing directions.
1.7		(Dashed line with short strokes and equal intervals) - indicates traffic lanes within the intersection. It is used to mark the parking area.
1.8		(Wide dashed line) - indicates the boundary between the acceleration or deceleration lane and the main lane of the carriageway (at intersections, road intersections at different levels, in the bus stop area, etc.).
1.9		Indicates the boundaries of traffic lanes on which reverse regulation is carried out; separates traffic flows of opposite directions (when reverse traffic lights are off) on roads where reverse regulation is carried out.
1.10		Indicates places where parking is prohibited. It is used alone or in combination with the sign 3.28 and is applied at the edge of the carriageway or along the top of the curb.
1.11		Separates traffic flows of opposite or passing directions on road sections where rebuilding is allowed only from one lane; indicates places intended for U-turns, entry and exit from parking areas and the like, where traffic is allowed only in one direction.
1.12		(Stop - line) - indicates the place where the driver must stop in the presence of a sign 2.5 or with a prohibitory traffic signal (traffic controller).
1.13		Indicates the place where the driver should stop, if necessary, to give way to vehicles moving on the intersecting road.
1.14.1, 1.14.2		("Zebra") - denotes a pedestrian crossing; marking arrows 1.14.2 indicate the direction of movement of pedestrians.
1.15		Indicates the place where the cycle path crosses the carriageway.
1.16.1, 1.16.2, 1.16.3		Indicates guide islands where traffic flows separate or merge.
1.17		Designates places of stops of fixed-route vehicles and parking of a taxi.
1.18		Indicates the directions of traffic allowed at the intersection along the lanes. Used alone or in combination with signs 5.15.1, 5.15.2; dead end markings are applied to indicate that turning into the nearest carriageway is prohibited; markings that allow a left turn from the leftmost lane also allow a U-turn.
1.19		Warns of approaching a narrowing of the carriageway (a section where the number of lanes in a given direction decreases) or marking lines 1.1 or 1.11 separating traffic flows in opposite directions. In the first case, marking 1.19 can be used in combination with signs 1.20.1 - 1.20.3.
1.20		Warns about approaching the markup 1.13.
1.21		(The inscription "STOP") - warns of approaching marking 1.12 when it is used in combination with sign 2.5.
1.22		Indicates the number of the road (route).
1.23.1		Denotes special lane for transit vehicles.
1.23.2		Denotes footpath or the pedestrian side of the bike path.
1.23.3		Indicates a cycle path, the cycle side of a cycle path, or a cycle lane.
1.24.1, 1.24.2, 1.24.3, 1.24.4		Duplicates the corresponding road signs. Markup 1.24.4 can be used on its own.
1.25		Indicates an artificial roughness on the roadway.

Lines 1.1, 1.2.1 and 1.3 must not be crossed.

Line 1.2.1 is allowed to be crossed to stop the vehicle on the side of the road and when leaving it in places where stopping or parking is allowed.

Lines 1.2.2, 1.5 - 1.8 are allowed to cross from any side.

Line 1.9 in the absence of reversing traffic lights or when they are disabled, it is allowed to cross if it is located to the right of the driver; when reversing traffic lights are on - from either side, if it separates the lanes on which traffic is allowed in one direction. When reversing traffic lights are turned off, the driver must immediately change lanes to the right beyond the marking line 1.9.

Line 1.9, which separates traffic flows of opposite directions, is prohibited to cross when reverse traffic lights are turned off.

Line 1.11 is allowed to be crossed from the intermittent side, as well as from the solid side, but only when overtaking or bypassing is completed.

In cases where the meanings of road signs, including temporary ones, and horizontal marking lines contradict each other or the markings are not sufficiently distinguishable, drivers should be guided by road signs. In cases where temporary marking lines and permanent marking lines contradict each other, drivers must be guided by temporary marking lines.

Vertical layout

Vertical markings in the form of a combination of black and white stripes on road structures and elements of road equipment show their dimensions and serve as a means of visual orientation. Vertical layout:

Partition number Image Explanation

2.1.1, 2.1.2, 2.1.3		Designate elements of road structures (supports of bridges, overpasses, end parts of parapets, etc.) when these elements pose a danger to moving vehicles.
2.2		Denotes round bollards installed on dividing strips or traffic islands.
2.3		Indicates the lower edge of the span of tunnels, bridges and overpasses.
2.4		Denotes guide posts, gouges, fence supports and the like.
2.5		Denotes side surfaces road barriers on curves of a small radius, steep slopes, and other dangerous areas.
2.6		Indicates the side surfaces of road barriers in other sections.
2.7		Denotes curbs in dangerous areas and towering safety islands.

Is it possible to cross the marking 1.1 if it is yellow (photo)?

In the picture you see a road with two lanes, one lane in each direction.

Marking 1.1 (single solid line) is applied in the middle of the road.

However, for some reason it is yellow.

Can you cross it?

Will the driver of the blue car violate traffic rules by driving along one of the trajectories: along A or along B?

From the SDA, I know for sure that the solid marking lines 1.1 do not intersect. It is only possible to pass ahead of a crawling slow-moving vehicle with a corresponding sign on the body and traveling at a speed of 30 km / h or less and to avoid a fixed obstacle.

And now about the color of the road markings. Permanent road markings are white, except for the lines at the edge of the road that prohibit stopping and parking, etc. The marking line 1.1, which separates oncoming traffic, may be yellow.

A regular truck is driving ahead of the blue car. In my opinion, the driver of the blue car will violate traffic rules in both cases of his maneuver on a road with a solid marking line on a two-lane road with different directions of movement.

Elena212

As far as I know, yellow markings are applied temporarily, for example, during road repairs. You should not neglect it, since it indicates the same functions as solid white color,with the only difference is that it is temporary. And this means that the car cannot cross this lane.

What does a solid, yellow, dividing strip on a road outside the city mean. p.s. the road is straight, without any turns

According to traffic rules. Thank you

Wanderer

If literally so that dividing, that is, in the middle of the road, then this can only mean one thing.
The presence of a "big mind" and the absence of white paint from the organization serving this section of the road.
Well, and as a result, a disregard for GOSTs, in this case GOSTs of traffic rules (according to GOST R 51256-99 and GOST R 52289-2004).
============
I made such a conclusion based on the fact that, according to the terminology, the word "separating" should be used in relation to lines SEPARATING traffic flows.
And if the yellow lines are drawn at the edge of the carriageway or along the top of the curb, then this is just a road marking, but not a dividing strip.

Lyalya

Do not cross, do not park. The part of the road beyond the yellow lane is reserved for public transport. They are used on sections of roads where stopping vehicles is prohibited, both separately and in conjunction with sign 3.27 "Stopping is prohibited." The marking is applied at a distance of 0.1-0.2 m from the edge of the carriageway or along the top of the curb.

Igor Telnov

They have white paint and not the edge of the roadway, but a dividing yellow strip that separates oncoming flows. This is a temporary strip, i.e., there is or will be a road repair. Only whether it is possible to cross it or not, I do not know, Who knows, write

What does the yellow dividing line mean

What does the yellow, solid dividing strip mean (dividing the carriageway into two lanes). ?

Ps its length is not less than 10 km. along a straight road. is located on the road Nikolaev - Crimea.

My thoughts: 1. Temporary, but somehow stupid 2. Plain solid, but yellow), also not an option, since there are no prerequisites for a solid one.

By traffic rules Ukraine.

maria worth

))))) The white paint is over)))) And so On the one hand, solid and intermittent on the other. but usually they paint like this at parking lots WHERE along the Yellow Stripe Parking is Prohibited. By the way, in the States All the markings are Yellow ... well, for Colorblind people.)

Psychologist

I think it is the best way by color - for example, in Moscow, when building an extra row or pipeline like on Kashirka, they draw yellow stripes to separate the lanes and directions, that is, the attention of drivers is instantaneous to this color, and if on such a single-lane road, then just like the white color to cross it’s impossible, it’s only possible when it’s interrupted for a U-turn, and now in Thailand in Phuket and I always rent a car, the roads are awesome (apparently they don’t steal asphalt and there is no winter) and where the road goes on the passes between the bays or along the crossroads, the single-lane is painted in yellow color and metal fenders are also added on this line every 10 meters - that is, if you move a little, then the noise from them prompts and this color is also much more visible both in heavy rain and at night, so this best color and I think not only I am alone, and yellow is the color of attention first of all, good luck to you

Sergey Davidov

They mow down under the Americans.

SDA of Ukraine Addendum 2:
Lines 1.4, 1.10, 1.17, and also 1.2 are yellow, if it marks the boundaries of the lane for the movement of route vehicles.
(...)
1.2 (wide solid line) - indicates the edge of the carriageway on motorways or the border of the lane for the movement of route vehicles. In places where other vehicles are allowed to enter the lane of fixed-route vehicles, this line may be intermittent;

I think that if there are any difficulties during operation, we will be able to quickly reorganize and take prompt measures,” he said. Safronov explained that the decision to apply temporary markings was made by the Ministry of Transport of the Republic of Kazakhstan, the traffic police and the highways Crimea in order to increase the capacity of cars at the entrance to Yalta. “Therefore, we carry out these activities according to common decision and we will study and monitor how it all works,” he said. By the beginning of the holiday season, Crimean roads will be equipped with photo and video recording tools Safronov also said that in general, the Road Service of the Republic of Kazakhstan, together with the traffic police and the Ministry of Transport, developed about 6 measures to increase the throughput on Crimean roads in summer period. “And in the region of Feodosia, and in the region of Sak, and Yalta. Of course, they will not solve the problems that will arise in the summer, one hundred percent.

Road markings in red

Marking is applied at the edge of the intersection of carriageways. 1.14.1 Pedestrian crossing, designates an area for pedestrians to cross the carriageway, drivers are required to give way to a pedestrian as soon as a pedestrian enters this marking. 1.14.2 Pedestrian crossing, indicates a zone for pedestrians to cross the carriageway, drivers are obliged to give way to a pedestrian as soon as a pedestrian enters this marking. The arrows on the markings indicate the direction of movement for pedestrians.

1.15 Indicates the intersection of the carriageway with bike path obliges to give way to a cyclist. 1.16.1 1.16.2 1.16.3 Designates guide islands in places of separation or confluence of traffic flows.

Detected blocking ads on the site

A double solid marking line separates traffic flows of opposite directions on roads with four lanes or more. It is strictly forbidden to cross such markings. 1.4 Solid yellow road markings prohibit stopping vehicles.

It is applied to the edges of the carriageway, duplicates the prohibition sign 3.27 "Stopping is prohibited." 1.5 Discontinuous road markings, marking the boundaries of lanes in the presence of two or more lanes intended for movement in one direction, separates traffic flows in opposite directions on roads where there are two or three lanes. 1.6 Intermittent road marking line, warns of approaching a solid marking line. A dashed line whose strokes are 3 times longer than the spaces between them.

1.7 A broken road marking line, indicates lanes at an intersection.

What does the red stripe on the roads of Yalta mean?

Info

When the reversing traffic light is off, entry into the reversing lane is prohibited. Marking 1.11 a) can be crossed from the side of the broken line, as well as from the side of the solid line, but only when returning to the previously occupied lane after completing a detour or overtaking.

Attention

Figures 1 - 9: Application of horizontal markings. Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6.

Figure 7. Figure 8. Figure 9. II. VALUES OF VERTICAL LAYOUT. Vertical road markings are applied to road structures, indicate their dimensions and serve as a means of visual orientation. Marking 2.1.1 - 2.1.3 and 2.2 is made in the form of a combination of red and yellow stripes, and marking 2.5 in the form of a combination of black and white stripes.

Vertical marking means: 2.1.1 2.1.2 2.1.3 2.1.1 - 2.1.3 - elements of road structures (supports of bridges, overpasses, end parts of parapets, etc.).

Exam traffic rules

Important

Line 1.8 - indicates the border between the deceleration or acceleration lane and the adjacent lane of the carriageway (at intersections, intersections at different levels, in the area of ​​stops of route vehicles, etc.). 1.9 Two parallel narrow dashed lines, whose dashes are three times longer than the gaps between them, mark the boundaries of the lanes, the movement of which can be reversed, and also separate traffic flows when reverse traffic lights are on: 1.9 a) - passing directions; 1.9 b) opposite directions. 1.10 Narrow broken line - indicates places where parking is prohibited. Line 1.10 can be used alone or in combination with signs 3.32.1 - 3.32.3, limiting their area of ​​operation.

Apply to sidewalk curbs or at the edge of the carriageway.

It became known why red stripes were applied to the roads of Astana

Naturally, vehicle drivers are prohibited from stopping and parking in such areas. The exception here is fixed-route and regular taxis.

Finally, I would like to give some advice. Firstly, do not be lazy to learn about the changes made to the traffic rules. The rules don't change very often, but they do change. Well, not knowing, as you know, does not exempt from responsibility.

In addition, when driving on the road, always strictly follow the rules. After all, the safety of both you and other road users depends on it.
Don't neglect traffic rules, hoping that it will “carry through”, and no one will notice your violation. The rules are written taking into account many years of experience, and are aimed primarily at maintaining order on the roadway and ensuring the safety of seven road users.
Sometimes an improperly parked car can cause an accident.

Road markings full description.

In particular, it happens:

• white;
• orange;
• yellow.

The markup serves as an addition to the established road signs. In addition, it delimits the carriageway and highlights the traffic lanes.

The markings also warn of approaching dangerous areas or certain road signs. In most cases, it is the usual white color.

Such markings divide the carriageway into lanes and mark the edges of the road. Depending on the situation, the line can be solid or broken.

The first, as you know, cannot be crossed. Well, the most serious fines are issued when the drivers of the vehicle make any maneuver through a double continuous line. Also, white markings indicate a pedestrian crossing and a stop line, including in front of traffic lights.

Don't yawn on the road, two stripes, and you've got it!

A narrow solid zigzag line with or without the inscription “BUS” or “TAXI” indicates a stopping place for route vehicles (buses, trolleybuses) or a taxi rank. 1.17.2 Alternating lines that are applied to the transverse noise strips. 1.18 Arrows with a straight stem indicate the permitted directions of movement along the lanes at the intersection. Marking 1.18 may be used alone or in combination with signs 5.37.1, 5.37.2, 5.38.1 - 5.38.4.

Dead end markings indicate that turning onto the nearest roadway is prohibited. Markings that allow a left turn from the leftmost lane also allow a U-turn.

Yellow markings on the road - what does it mean

It also does not prohibit parking in emergency cases - in the event of a car breakdown, or in some unforeseen situation. The latter, for example, include insurmountable obstacles that have arisen on the road, or health problems for the driver of the vehicle.

If a broken or solid yellow line is drawn along the right edge of the carriageway outside locality, then the driver will not be allowed to stop or park here. It is worth noting one point. The restriction applies to the entire length of the line.

That is, as soon as it ends, all prohibitions and restrictions are removed. See also: How to check traffic police fines through the Yandex. Fines” A yellow zigzag line marked on the carriageway indicates the place where public transport stops. Such markings are quite noticeable - they catch the eye faster than the corresponding road sign.

road markings

Coldfield, a suburb of Birmingham, has the first UK label. This road safety experiment was so successful that white road markings have since become the standard in the UK and many other countries. Some time in different countries used different variants road markings. For example, in Germany in the 30s they used black markings, which were later abandoned as ineffective. Currently, black is used in combination with white when applying vertical markings. In 1930, in the UK, a retroreflective device invented by the British Percy Shaw was patented to improve visibility on the roads - "Cat's Eye", which received wide use in the United Kingdom during World War II, when reflectors kept the road visible to drivers even during blackouts.