How to glue wallpaper in the inner corners. How to glue wallpaper in the corners: a master class on pasting corners with wallpaper

If you decide to make repairs, get ready for a complex process that will take a lot of time and effort. And turning to professionals, it will also be costly in terms of finances. Therefore, in order to save your money, we suggest that you at least partially carry out the work yourself. For example, you can easily cope with such a process as wallpapering the walls. The only difficulty that you will have to face is the design of the corners of the room. As a rule, this work always causes difficulties.

Unfortunately, both owners of apartments in old houses and in new buildings face uneven corners. Often there are flaws on the walls that make it difficult to paste the wallpaper beautifully and quickly. What to do in such a difficult situation and how to glue wallpaper in the corners? Below you will learn about all the important points, and for clarity, you can watch the video.

Pasting corners: features

If you are pasting external corner protrusions, make sure that the wallpaper sheets fit snugly against the wall, so it is not recommended to glue the entire strip on the corner at once.

If the joint of the walls is bad, it will simply gather into ugly folds. Moreover, wallpaper should never end in a corner. It is necessary to leave a protrusion of approximately 3 cm (if necessary, cut it with a knife). In this way, you can achieve a perfectly even gluing. When using thick wallpaper for wall decoration, use a plumb line.

If there are switches or sockets nearby, remove the covers from them, turning off the electricity. Next, glue the canvas on top, then cut out circles of a smaller diameter than the casing itself. You can put them back when finished.

Preliminary preparation

It should be noted right away that all the preparation must be done long before gluing the wallpaper in the corners. First you need to remove the old finish, level the surface. To align the joints of the walls, use plastic corners, fixing them with putty.

Then the surface is treated with a primer, which can be found in every hardware store. The primer is applied with a roller or brush.

How to glue wallpaper in the corners: technology

It is impossible to glue all corners at once. Choose the one from which the work begins. To do this, prepare a strip of the required length and, depending on the type of wallpaper, coat with adhesive both one wall (when pasting with non-woven wallpaper) and the wallpaper (in the case of vinyl wallpaper). If you use plastic corners, you need to coat them with glue.

When processing the surface of the wall, it is necessary to capture an area slightly wider than the wallpaper (at least 5 cm).

Then you can start gluing the first canvas. If you are going to start pasting from left to right, you need to apply the left side of the canvas to the corner. The strip of wallpaper is located exactly along the entire length.

Then the canvas must be carefully leveled and all air must be expelled from it. This can be done with a plastic spatula or a special roller. After that, the entire wall is pasted over to the next corner.

Internal corners

Interior corners are the most common in rooms. For proper gluing, you must follow these recommendations.

The strip must be glued so as to capture not only the corner itself, but also a few centimeters of the adjacent wall. Next, it is important to press and smooth the wallpaper well using a lint-free cloth or sponge.

Then, using a ruler or tape measure, it is worth measuring the width of the wallpaper on the adjacent wall from the upper corner, folding back 3-4 cm. This is necessary so that you can glue the strip overlapping the previous one. Further along these points, using a plumb line or level, you need to draw a line along the wall. The canvas glued on it will be strictly vertical.

Next, you need to start pasting the adjacent wall. As noted above, the canvas is overlapped with the previous one along the drawn line. Further actions are traditional: the wallpaper strip is smoothed and pressed. Using a level, ruler or paint knife, it is necessary to cut through both layers of wallpaper in the corner, removing all trimmings. It is important to do this especially carefully. If it is difficult to pry off the edge of the wallpaper, you can carefully bend the second canvas, removing all unnecessary. After that, coat the folded canvas with glue, pressing it well and smoothing it out, getting rid of the air.

By resorting to this technology of pasting the inner corners of the room, you can make the joint in these places invisible.

External corners

In almost every room there are external corners (slopes). For easy and high-quality gluing, it is necessary to pre-align them with plaster. But to do this will not always work. In this case, without overlapping pasting, you will not be able to achieve the desired result. Consider how to wallpaper the outer corners in more detail.

First you need to glue the wallpaper canvas so as to capture 3-4 centimeters of the adjacent wall. Moreover, it is important that the wallpaper fits evenly and tightly against the wall and corner. For this reason, if necessary, cut them in several places.

After smoothing the canvas, cut off all excess wallpaper (vertically) with a sharp blade or knife, leaving a thin edge.

Then measure the width of the roll with a large ruler or tape measure and, stepping back about 5 mm, draw a vertical line using a plumb line or level. The next strip is glued on it. She will lay flat. As a result, you will get a small overlap. It will allow you to hide all the defects that occur after cutting the first strip.

Features of gluing wallpaper with a pattern

If your wallpaper has a pattern that is distinguished by good clarity (for example, some geometric shapes and forms, vertical or horizontal stripes), you need to make sure that wallpapering in the corners does not distort it in any way.

This can be done easily. It is only important not to forget about the need to perform a slight overlap on the wall. The canvases must be glued so that the edge lies exactly along the plumb line. Then trim the second edge of the canvas along the edge of the corners.

Most likely you will not be able to completely eliminate the shift of the pattern, as a result of which a slight distortion will remain. But only you know about such a shortcoming. To identify it, you need to carefully study the lines connecting the walls. If you strictly adhere to the instructions on how to properly glue the wallpaper, the canvases will lie exactly vertically, and slight distortions of the pattern will be invisible.

How to glue wallpaper in the corners of a room: some secrets

• If your wallpaper is heavy and thick, it would be a good idea to arm yourself with a strong adhesive. It's good if it's transparent.

By following our simple tips, you will wallpaper the corners of the room perfectly. And they will look beautiful, even uneven wall joints. You just need to be patient and do all the work carefully.

At first glance, wallpapering seems simple and even interesting: what could be easier than smearing a piece of roll with ready-made glue and gently pressing it against the wall?

However, during operation, surprises appear in the form of uneven walls, bubbles, gaps and spots. One of these surprises is the problem with wallpapering in the corners. This is the hardest part of the hard work. Further in the article, we will tell you where to start gluing wallpaper, and also share secrets when working in uneven places.

Attention

Choosing an "opening" corner is not the first thing you need to start repairs with. Usually, between a firm decision to update the appearance of an apartment or room and the purchase of materials, at least a week passes, during which you need to get rid of the old coating, level the walls, and prepare them for repair. Only after that determine the direction of gluing.

Why can't you start from any convenient place? It is possible if the walls are in perfect condition, and a professional with experience is engaged in the repair. In other cases you need to start strictly from a certain place, because the first canvas sets the direction for all the others: if you make a mistake with him, then everything will go awry.

Hobbyists and beginners alike can start with a doorway or window. Materials are glued in a circle. Even if as a result the last canvas is wider than necessary, it will not be evident. This method of gluing will save, if necessary, matching the pattern (find out how to select a pattern and cut wallpaper in difficult places).

For the first canvas, you need to make a vertical markup using a plumb line. If the option from a window or doorway is not suitable due to their absence or irregularities, they start from the most inconspicuous corner: for example, where the cabinet will stand in the future. The angle cannot be considered a reliable guide, but in the absence of other options, it is better to play it safe.

The vertical line must be drawn. They draw it on the wall at a distance equal to the width of the roll minus 2-3 cm. Then the first canvas is glued exactly along the line, and the remaining 2-3 cm capture the perpendicular wall.

Procedure

The first 2-3 glued canvases help you get used to the process and understand the technique. Further work goes faster, easier, until it comes to the next corner.

outdoor

At the outer corners (these are the ones that are “bulging”) you will have to slow down. The process of pasting the outer corners is very painstaking and takes place in several stages..

1. First you need to measure the distance from the corner to the last glued strip and add 2.5 cm to the resulting value. For accuracy, it is better to measure both from above and from below, since perfectly even corners are very rare.
2. After measuring, you need to cut off a strip of wallpaper of the required width and glue it.

   First you need to carefully press the wide part of the canvas, and the remaining 2.5 cm overlap - this part is pressed last.

3. The next strip will be glued strictly from the corner, and the existing 2.5 cm from the previous canvas will “hide” under it: this way you can hide the bumps.

Internal

Internal corners are insidious in that with the wrong technique, instead of a smooth transition, a curved line is obtained, full of bubbles, dents, crooked creases. Therefore, they are glued like this:

1. The distance from the last canvas to the corner is measured. 1-2 cm is added to the obtained value.
2. The next canvas is measured in accordance with the received width and carefully cut along the previously drawn vertical line on the reverse side.
3. The canvas is carefully applied to the wall, carefully greased with glue. It must be pressed well with a roller, spatula or improvised means so that bubbles (?) do not form.

1-2 cm added during measurements will be on the next wall. They need to be cut slowly and very carefully with a sharp construction knife, holding the fresh canvas with a spatula. The main thing in this matter is not to rush.

The nuances of working with certain types of materials

Meter

The main rule for gluing wide wallpaper in the corners is this: the width of the entry should not exceed 5 cm. You do not need to save and paste the entire canvas, otherwise the result will be unsatisfactory.

1. The corner is leveled with a plastic spatula or a clean, dry cheek with a coarse pile.
2. At the narrowest point of the overlap, at a distance of 1 cm from the edge of the wallpaper, a mark is made along which a vertical line is drawn.
3. The next canvas is glued with a reference to this line.
4. The excess is cut off according to the already known scheme with a construction knife.

Vinyl

Vinyl wallpaper, unlike non-woven, must first be coated with glue. The order of pasting corners is simple and clear. How to properly glue vinyl material:

1. The size of the canvas should be taking into account the 5-centimeter overlap on the adjacent wall.
2. The canvas of the desired width is well smeared with glue, left for 10-15 minutes.
3. The corner must be pressed, remove all excess glue and air, walk with a roller or spatula from top to bottom.
4. The next canvas is glued with an overlap and is also firmly pressed against the wall.
5. Then you need to take a construction knife and draw a straight line along the steel ruler, preferably from the bottom up along two layers of wallpaper.
6. The top layer of wallpaper is gently pushed aside, and the allowances of the previous canvas (5 cm) are removed.

The canvas is returned to its place, it is carefully ironed with a dry cloth or rubber roller from top to bottom. There should be an even seam.

Non-woven meter

1. A solid web of non-woven materials cannot be used for pasting entire corners. This will cross out all previous and subsequent efforts, so they will also have to be cut. This is done according to a well-known scheme: measure the distance from the edge of the last pasted canvas, add 5 cm. Non-woven wallpaper, so measurements must be taken at the top, bottom and in the middle. Read about how to glue non-woven wallpaper correctly.
2. Then the wall is smeared with glue, and only after that the canvas is applied to the wall and pressed with a dry rag or rubber roller. You can’t rush into this matter: it’s better to carefully and thoroughly in the corner so that the walls do not look ridiculous.
3. Despite careful measurement, it is likely that the width of the lap will be different on the adjacent wall. You need to find the narrowest place, measure 1 cm from the edge, put a dot and draw a straight vertical line using a plumb line. A value equal to the width of the roll is measured from this line to the side. The vertical line is drawn again.
4. The next canvas will be glued already from the last drawn vertical line. Then you need to make a cut on both layers of wallpaper, gently bend the top and remove the "extra".
5. The joint is neatly aligned.

Read about the choice of wallpaper and the differences between different types of materials.

How to work in uneven places?

Most of the corners in the rooms are unfortunately uneven. Care should be taken to align them at the repair planning stage, but people do not always think about this problem.

There are several secrets to hide uneven corners.:

• The choice of non-woven wallpaper is the most flexible option.
• Coatings with a neutral pattern that does not need to be joined.

When wallpapering in the corners, you need to make at least two layers: for this, they make the very overlaps of 5 cm. Sometimes experts advise first gluing the corner with a narrow strip, and only then gluing wide overlapping canvases. For this, a grid is used.

Another trick - you can make small cuts in the shape of a Christmas tree at a distance of 5-10 cm from each other on the spade.

In order for the repair to be successful, and the appearance of the room not to be spoiled by irregularities in the corners, you can use simple useful recommendations:

1. If possible, it is better to entrust wallpapering to professionals who will definitely cope with the task.
2. Before you start finishing the walls, they need to be leveled in order to avoid both difficulties during the repair and troubles in the form of uneven joints (how to properly join the wallpaper, read how to repair the wallpaper and joints, if they are separated, find out).
3. If you don’t want to align the walls or there is no such possibility, they select materials with a pattern that does not need to be customized (?). It can be a monochromatic coating or an abstract, contrasting one with a small print, which even helps to mask irregularities.
4. You can’t rush during repairs or strive to complete the gluing in one day: if nothing works out of fatigue, it’s better to postpone work until tomorrow.
5. Windows should be tightly closed during pasting.
6. At the junction of the walls, you do not need to try to stick a whole wide canvas, even if you have to cut off a strip of considerable thickness. This strip may come in handy elsewhere, but the likelihood of getting beautiful walls increases.
7. Cuts should be made only with sharp blades of a construction knife, and dull ones should be removed more often.
8. It is better to plan the interior so that difficult and unfortunate places are hidden by furniture or large furnishings.
9. If possible, it is better to start gluing from doorways or windows.

Gluing wallpaper is always interesting and entertaining, so you should not give up this experience and skill in favor of painting walls or other coatings. always in fashion, especially given the modern assortment. If you follow the correct gluing technique, the corners will turn out to be even, beautiful, they will not have to be ashamed.

In contact with

Most of our fellow citizens are sure that even with a little experience in repair work, you can stick wallpaper with high quality and beautifully.

Perhaps this is the case when it comes to even walls and right angles.

But few apartments, especially the notorious Khrushchevs, can boast of such indicators.

How to stick wallpaper in the corners? Where is the best place to start, which side?

Next, choose an angle. with which we will start work. We prepare a piece of wallpaper of the right size, spread it with glue, if necessary, it also covers the piece of wall for which it is intended. When using plastic corners, they are also smeared with the composition. By smearing the wall, you can go a few centimeters beyond the scope of the future sheet.

Sticking the first strip. If the work is carried out from left to right, then the left side of the wallpaper strip is applied in the corner. Along its entire length, it should be placed perfectly evenly. With a clean cloth or a special device (plastic spatula or roller), the coating is smoothed over the entire area, moving gently and gradually, expelling air and removing bubbles. The wall to the nearest corner is glued completely.

How to glue wallpaper in inner corners

In rooms, corners of this type are usually found. For competent and even pasting, you must adhere to the above recommendations.

The strip is glued so as to cover, together with the corner, several centimeters of the adjacent wall (3-4). It is carefully pressed and smoothed with a clean, lint-free cloth.

Then, on the adjacent wall, with the help of a ruler from the upper corner, the width of the canvas is laid off minus the mentioned 3-4 cm. This is done in order to stick the next strip with respect to the previous overlap.

By means of a plumb line or level, a line is drawn down along the entire wall, which will serve as a guide. A strip must be glued along it strictly vertically.

After that, you can go to the adjacent wall. As already mentioned, the next strip is glued along the line marked on the wall overlapping the previous one. Just like everyone else, it is carefully smoothed and pressed, especially at the junction of the walls. Then, using a sharp knife, a ruler and both layers of wallpaper are cut through in the corner, unnecessary trimmings are removed.

This must be done carefully so as not to accidentally remove the desired piece of wallpaper. Then we coat the edges of the canvas with glue, smooth and press. Be careful not to form air bubbles. If you use this technique to finish the corners, then you can make the corner joint almost invisible visually.

How to glue wallpaper on outside corners

Meanwhile, along with internal, in each residential building there are also external corners. These are, for example, all the familiar slopes.

To make it easier and more accurate to paste over them, it is desirable first. Unfortunately, this does not work in every case. Then you will have to apply the method of pasting with an overlap.

How is it more convenient to do this?

As when working with internal corners, a layer of material is first glued to the adjacent wall, at a distance of the previously mentioned 3-4 centimeters.

To ensure an even fit of the wallpaper to the surfaces, it is allowed to carefully trim them in several places. When the canvas is smoothed, the excess is cut off with a blade or a sharp knife along the vertical edge, with the exception of a thin edge.

Then, with a large ruler or construction tape measure on the wall, a distance equal to the width of the roll plus five millimeters is measured. Using a plumb line from this point, we draw a vertical line down.

We will stick the next strip of wallpaper, focusing on it. When gluing two adjacent strips, you will get a slight overlap, which will mask all possible defects formed when cutting the first piece.

How to glue wallpaper with a pattern in the corners

If we have to work with a coating that has a clear and distinct pattern, it is important to make sure that the wallpaper sticker in the corners does not distort the existing pattern. This is not as hard to do as it might seem.

The main thing is not to forget about the need for some overlap. In addition, it is necessary to glue the canvas in such a way that the edge exactly corresponds to the plumb line. Then, along the edge of the corner (edge), the second edge is trimmed.

It is rather difficult to prevent pattern shift completely, and a small amount of distortion may occur. But it will be so insignificant that only you will most likely know about it. Only a careful study of the lines of intersection and connection allows you to notice it. If you follow all the recommendations for pasting the inner and outer corners, individual sheets of material will lie exactly vertically, and a slight distortion of the pattern will not be noticeable.

Conclusion

There are little secrets for pasting wallpaper in the corners.

Even if the joints are not too even, they will nevertheless look neat and beautiful.

The main thing is to be patient and careful, to do all the activities slowly and carefully. Then the result will please you!

Wallpapering the walls of an apartment is a common procedure for most residents of our country. This is the most affordable and easy way to update the interior, but not many owners understand how to glue wallpaper in the corners of the room. Such a seemingly simple task stumbles upon a lot of difficulties when it is necessary to paste over corners with an uneven surface. Especially a lot of problems arise with wallpapers that require fitting according to the pattern. An exact match of the image in a crooked corner cannot be achieved, and the overall picture will be hopelessly spoiled. You can endlessly join individual canvases on the wall, but without careful leveling of the surface in the corner and preliminary preparation, it will be impossible to achieve an acceptable result.

To avoid difficulties in the process of gluing wallpaper, special attention should be paid to the preliminary preparation of walls and corners. Even minimal protrusions or recesses in the corner can give a serious distortion over a meter length, and several such errors make it impossible to fit - creases and gaps appear, as a result of which wallpaper with different patterns cannot be joined.

To prepare the surface for wallpapering in the corners, you will need to perform the following work:

1. The first step is to clean the surface of old coatings, dust and dirt.
2. If small indentations are found, they are eliminated with putty.
3. If the wall is uneven, you need to find the point of maximum protrusion at the inner corner. Using a guide rail (metal profile) installed along a plumb line or level to an adjacent wall, a mark is made on which the angle is aligned with special building mixtures.
4. If it is impossible to level the inner corner with mortars, it is recommended to install a special corner made of metal mesh, after which it is necessary to plaster the corrected place. In the same way, you can prepare the outer corner.
5. Leveled and dried surfaces must be treated with sandpaper until a smooth surface appears.
6. After obtaining the ideal surface, it must be treated with a primer. This item of preparing the corner for gluing is mandatory, although many owners who do their own repairs ignore this procedure. The surface treated with primer allows to achieve a higher degree of adhesion of materials, which is especially important when working with corners.

The preparation will allow you to solve the problem of how to stick wallpaper in the corners of the room with high quality. In the same way, it is recommended to prepare complex surfaces at the locations of doors, radiators and windows.

How to wrap corners

To successfully overcome the problem of corners, both external and internal, it is necessary to prepare a set of tools that will allow you to do this job with less effort. The following tools will be needed for gluing paper, non-woven and vinyl wallpapers:

• plumb line or level to determine the vertical mark;
• a wide spatula, as a basis for even cutting wallpaper;
• stationery knife;
• brush 150 mm wide;
• roller, preferably on a long handle;
• pencil;
• scissors;
• rubber roller for rolling wallpaper;
• container for dilution of glue and primer;
• bath with a cuvette for working with a roller.

The technology for pasting the inner and outer corners in the room, proposed below, is valid only for plain products without a pattern that do not require image matching.

Internal

It is best to seal the inner corners using overlap technology. To do this, it is necessary to prepare a sheet with a width exceeding the width of the wall at the junction with the corner by 3-4 cm. This piece is intended for gluing the corner and a small entry into the adjacent wall.

After gluing the sheet, it is necessary to draw a strictly vertical line along this strip at a distance of 0.5 cm from the corner. This mark will be a guideline for the second sheet of sticker on the adjacent wall. To obtain a vertical, use a plumb line or a laser level.

The second sheet is glued so that its edge coincides with the vertical mark. If the seam is invisible, you can proceed to further pasting the walls, if it protrudes noticeably, you will have to make a leveling cut, for which a clerical knife and a wide metal spatula are used as a guide surface for the knife.

After trimming, the excess strips are removed, at the junction, the wallpaper is slightly diluted and additionally smeared with glue, after which it is joined again.

outdoor

Modern projects practically do not provide for external corners in the space of the apartment, but in the previous series such corners exist, so you should consider step-by-step instructions for pasting such walls:

1. As in the case of an internal corner, it is necessary to prepare a trellis with a width exceeding the space of the wall up to the corner by 4-5 cm;
2. Glue is smeared with a sheet of wallpaper and the surface that is planned to be pasted over;
3. The trellis is glued to the main place and carefully leveled, removing air plugs;
4. After strengthening the sheet on the main wall, they begin to bend the wallpaper in the corner. If necessary, small incisions can be made to smooth out wrinkles that form when the surface is uneven;
5. The next step is to make markings on the strip, stepping back from the angle of 0.5 cm. The markings must be strictly vertical, for which it is recommended to use a plumb line or a laser level;
6. Glue is applied to the second sheet and the wall, after which, aligning the edge of the sheet along the line, it is glued;
7. Using a guide (wide spatula, long metal ruler or profile), a vertical cut is made in the middle of the connected parts;
8. The cut strips are removed, and the joint is additionally coated with glue and rolled with a rubber roller.

Each master involved in finishing works has his own set of optimal solutions to issues that arise in the process of pasting. Below are tips from professionals to help you understand how to properly glue wallpaper in the corners and avoid mistakes:

• For pasting walls with dense roll materials, the most durable types of glue should be used, and you need to choose glue with a transparent structure;
• The application of soil to the entire surface of the walls, and especially at the joints, is mandatory;
• Often, fitting the pattern in the joint takes a lot of time, which leads to the drying of the glue, so it is necessary to add the adhesive composition in time in places where it has dried;
• In old panel houses, significant deviations can be found in the corners. In this case, effective alignment is difficult to carry out, therefore, to facilitate the work, wallpaper without a pattern should be purchased to avoid fitting;
• If there is no special primer mixture, it is recommended to use wallpaper glue to treat the surface before pasting. It is enough to apply it 5 hours before the start of the main work, as a result of which the setting of materials will be much more reliable;
• Lubricate the corners with a brush. The roller will not be able to cope with the full processing of the entire surface of this assembly, which will adversely affect the setting of the material;
• In complex pairings with large deviations, it is recommended to glue a strip of small (up to 15 cm) width before sticking the main panels end-to-end. Such a precaution will protect the connection when joining the wallpaper and disguise flaws in case of inaccurate fit. This method is used only for plain wallpaper without a pattern;
• For those who still have difficulty imagining how to glue wallpaper in the corners without marriage, it is recommended to use non-woven wallpaper. They mask the flaws of problematic surfaces best of all;
• If wrinkles form when smoothing the canvas, they can be carefully cut at an angle of 45 degrees, which will eliminate the unevenness and continue working;
• The smoothing of the cloth is carried out until the air pockets are completely eliminated. Otherwise, these places will not stick and over time will lead to peeling of the entire trellis;
• When using the method of overlapping wallpaper, followed by cutting off extra centimeters along the length, it is necessary to carefully remove the joints from the wall with a wide metal spatula, and again coat with glue, since when removing excess strips, glue is also removed from the wall. It is better to cut off the excess with a clerical knife, using a wide spatula as a guide base.

These practical tips will allow any novice home master to cope with difficulties and understand how to glue wallpaper in the corners of a room without mistakes.

Docking wallpaper with a pattern

Of particular difficulty is the work of wallpapering with a pattern. With minimal vertical wall errors, docking is usually successful. Pattern shifting is possible, but this shortcoming does not affect the overall picture.

For a better fit of two sheets according to the pattern, it is necessary to spread both tapestries on a flat surface with the front side to the top. Next, you should take measurements from the last glued sheet to the corner at the top and bottom. These distances must be set aside on the first sheet, and another 5 cm should be deviated from the marks obtained.

By connecting the points vertically, we get a fold line (first measurement) and a cut line (second measurement). On the second line, the excess wallpaper is cut off.

The resulting sheet is superimposed on the second sheet, intended for joining, and adjusted according to the pattern so that the minimum point along the width of the first sheet overlaps by 3-4 cm, after which the second sheet is cut to the required height.

When both sheets are ready, an adhesive is applied to them and to the walls and the finished parts are applied, neatly joining them according to the pattern. The process of smoothing trellises is described in the previous methods for pasting corners.

The overlap is cut off with a clerical knife and a guide base (trowel), the cut strips are removed, and the joint is additionally smeared with glue and rolled with a rubber roller.

Gluing modern wallpaper is a simple matter. Even a beginner in the repair business will cope with this. But, if mounting canvases on smooth walls is easy and simple, then you will have to tinker with the corners. It is the corners that become the stumbling block that slows down the whole process and requires a lot of effort. More often than others, non-woven wallpaper or non-woven vinyl canvases are used in repairs.

Material Features

The wallpaper, which consists entirely of non-woven fabric, is easy to install and durable. They are made of non-woven cellulose with the addition of synthetic components. The cellulose component gives the wallpaper elasticity and breathability, while synthetics add strength. Such wallpaper is much more difficult to tear than paper-based vinyl, for example. In addition, they do not crumple at all, there are no bends on the surface.

Non-woven vinyl wallpapers have the same properties. The only difference is that the canvases do not “breathe”, since vinyl does not let air through. Therefore, before gluing them to the walls, it is necessary to treat the surfaces with antibacterial primer or use glue with fungicidal additives. These measures will prevent the appearance of mold and mildew.

Non-woven wallpaper has a number of advantages over other coatings:

1. Their feature is good adhesion with glue and with any wall material. Such canvases do not need to be treated with an adhesive, it is applied only to the walls. The same applies to non-woven vinyl.
2. A useful quality of non-woven fabric is its resistance to stretching. The material does not shrink after the glue dries, the dimensions of the canvas do not change. Thanks to this, the joints do not diverge, and the seams between the strips remain invisible. This feature is especially useful for wallpaper intended for painting, as painting makes all wall defects even more noticeable.
3. Interlining cannot be washed, but can be dyed. But cellulose-based vinyl can even be cleaned with detergents, it also lends itself well to dyeing.
4. Due to the volume of cellulose fibers, such wallpapers align the walls, hide small irregularities. Durable synthetic components are resistant to tearing, this allows non-woven wallpaper to reinforce the walls. They do not allow cracking, holding the plaster.
5. Wallpaper on non-woven base can be easily removed, their two-layer allows you to leave the substrate on the surface and use it as the basis for new coatings.

Installation of wallpaper on the walls

There are several ways to glue wallpaper (it is easy to see them from a photo or video). One of them involves the initial pasting of all smooth walls, and then the corners. Other masters advise starting from the most noticeable corner in the room. There is no consensus on this issue - everyone can glue at their own discretion.

Wall preparation is a must for any method. The old coating must be carefully removed, the cracks must be puttied. Then the walls are covered with a special primer or wallpaper paste. Only after complete drying of the primer proceed to pasting the walls.

In place of the reference point, a vertical line is drawn; this should be done with a plumb line or a building level. The first strip is cut from the roll, the length of which is equal to the height of the wall plus 5-7 cm. The wall is carefully coated with glue and wallpaper is applied. Level the canvas with a plastic spatula or wallpaper roller, focusing on the vertical.

Advice! It is better to use a special glue with a color indicator - in liquid form, such a composition has a pink tint, and after drying it becomes colorless. This allows you to evenly apply glue to the wall, leaving no "gaps".

At the plinth and under the ceiling, the wallpaper is cut with sharp scissors or a construction knife. Move on to the next lane.

How to glue wallpaper in the corners

In order to qualitatively paste over the corners, you first need to deal with their types. Angles are:

• Internal - each room has at least several of these corners (four in the standard layout). A very important factor is the correctness of these plots. If the angle is uneven, has drops, “sinks”, the wallpapering method will differ from the standard one.
• External corners in apartments have become more common with the advent of drywall - a variety of niches, arches, columns and other decorative elements. This also includes door and window slopes, unless, of course, it is provided to start wallpaper on these areas.

The easy way

The easiest way to paste over a completely flat corner. Unfortunately, these are quite rare. These are either drywall constructions, or walls prepared for painting (plastered perfectly smooth and even).

In this case, both in the inner and in the outer corners, the wallpaper is glued in the same way - they simply turn into a single piece of wallpaper. The main thing is not to stretch the coating, after drying it can return to its original size and shape. If there are small wrinkles on the wallpaper, it is allowed to make several horizontal cuts in the corner. This will help even out the coating, and cuts after drying will not be noticeable.

Important! No matter how even the corner is, it is better not to use the method of gluing it with a solid canvas if it is joined to the outer wall. In the corners located near the outer walls, condensation appears more often - the wallpaper can peel off and deform.

Standard Corner Taping Method

It is more reliable to glue wallpaper in the corners using the "overlap" method. Its essence is as follows:

1. After gluing the adjacent wall at three points, measure the distance to the corner.
2. According to the largest of the three values ​​\u200b\u200bobtained, a strip is cut off - its width is equal to the largest figure plus 2-3 cm for overlap.
3. The wall is well coated with glue, especially paying attention to the corner (it is better to use a brush).
4. The prepared piece of wallpaper is applied to the corner, combining the joint with the previous canvas.
5. The overlap formed on the adjacent wall is carefully pressed, tucking the wallpaper into the corner with a plastic spatula.
6. For a tighter fit, the edge of the wallpaper can be trimmed - short horizontal cuts are made every 5 cm.
7. Trim the bottom and top edges of the wallpaper using a metal spatula and a sharp knife.
8. From the narrowest point of the overlap, they recede about one centimeter towards the corner, make a mark.
9. Focusing on the mark, draw a vertical line in this place using a plumb line or level.
10. Prepare the next strip (if necessary, select a pattern).
11. A strip is applied to the wall smeared with glue, aligning its edge with the previously drawn line in the corner.
12. Level the strip, expelling air and excess glue. Cut under the ceiling and near the floor.

Corner done! They proceed to pasting a flat wall to the next corner - the procedure is repeated. In this way, you can glue the outer corners with diverse wallpaper

Advice! Given the considerable thickness of non-woven wallpaper, the overlap may be too noticeable.

In this way, you can paste over those corners that furniture or curtains will hide, and choose another way to finish the rest. You can also try cutting off only the top layer of wallpaper.

Slopes do not have to be glued with wallpaper, the video shows how they can be beautifully trimmed at the corners:

Corner cutting method

If the walls are supposed to be painted, there should not be any overlaps on them. The paint will make the thickening of the wallpaper too noticeable, here you need another way. This method is suitable for both internal and external corners.

The work is performed in the following sequence:

1. The first seven points from the previous instructions are repeated - the strip is glued with an overlap on the next wall. Only in this case, the overlap is made larger - 5-7 cm.
2. A distance equal to the width of the roll minus one centimeter recede from the corner.
3. Using a plumb line or level, draw a vertical line at this point.
4. A strip is cut off from the roll and applied to the wall smeared with glue, aligning the edge with the drawn strip.
5. The second edge is applied to the previous strip with an overlap, the wallpaper is pressed and leveled.
6. Carefully push the wallpaper into the corner with a spatula, leveling everything again.
7. In the middle of the overlap, a metal ruler is vertically applied, a very sharp knife is taken and a line is drawn without interruption along the edge of the ruler. It is very important that the line is drawn in one motion.
8. They remove the trim of the upper canvas, bend the edge of the lower one and also remove the excess.
9. Both edges are smeared with glue and folded end-to-end. You can pull the canvas a little in the right direction so that there is no gap or overlap.
10. Rolled with a roller for joints.

This method helps to make the connection of the canvases invisible. It works well on external corners, in niches and on slopes.

Advice! It is better to use a small metal spatula 10-15 cm instead of a ruler

Due to the unevenness of the corners, the ruler may not fit snugly against the wall, the cut will turn out to be crooked. The spatula must be moved along with the knife, avoiding breaks in the cut line. How to properly trim the wallpaper in the corners, you can see in the video: