Folding bench table drawing. Do-it-yourself transformer bench - not only convenient, but also beautiful

In order for the garden plot to be comfortable enough, it should be properly equipped. An important component are garden benches. They can be made independently in different ways and from various materials.

Bench made of concrete slabs and boards with a back

Looking at the drawings of the bench, you can find out the features of its device. You can make such a design with your own hands relatively easily, quickly and without high financial costs.

Making a bench with a backrest with your own hands in a step-by-step instruction is described in great detail.

Assembly: the initial stage

After the preparatory work, the time for wood processing is coming. In order for a do-it-yourself bench with a back to serve for a long time and decorate the site, it is necessary to pre-process the materials.

wood cover antiseptic formulations and let dry. After that, you can start collecting backs.

On one of the two-meter boards, fifty centimeters are measured from the edges. At this level, the edges of the white will be located.tons of slabs. From this mark another fifteen centimeters are measured to the center of the board. Here the first boards will be attached. From the resulting marks we measure seventeen and a half centimeters - the gap between the boards of the back. Next, we measure fifteen centimeters for two more boards. Between them there should be a gap of five centimeters. All this can be seen in the drawing.

Wood glue is applied to sections of fifteen centimeters. Boards are applied to them, the length of which is sixty-five centimeters. Additionally, they are fixed with self-tapping screws.

From above, between the boards of the back, pieces of seventeen and a half centimeters are glued. In order for the parts to stick together well, they are clamped and held until the glue sets. After gluing is completed, the back is covered with an antiseptic.

All wooden parts can be coated varnish. This will give them additional stability and attractiveness.

Assembly of the main part

It is better to collect the main part of the bench from two sides. Concrete slabs are placed between the boards, and M16 threaded rods fifty-five centimeters long are inserted into the drilled holes. They will need four pieces.

The rods are fastened with nuts and washers M16. They are twisted at the same time from different sides to make the bench even.

A simple bench with your own hands

You can make benches for giving with your own hands quickly enough if you follow the instructions. Consider four options for such garden structures.

On the drawings benches detail all its features. Making such a bench with your own hands is quite simple. The only difficult element is the concave seat.

The number of parts and their dimensions are indicated in the table.

The manufacture of benches with their own hands from wood begins with blanks the necessary details. Boards and timber are sawn into pieces of the desired length.

The manufacture of seat supports will be somewhat more difficult. You will need to markup on the blanks. Two points are marked along the edges at a distance of seven and a half centimeters from the bottom side, and in the center a point at a distance of four and a half centimeters. They are connected using a flexible plastic ruler and cut out jigsaw. Sections are treated with sandpaper.

Seat supports are attached to the two upper tsargs. One on each end and one in the middle. Next, the supports are screwed, spaced from the extreme ones by the width of the legs. All connections are made with self-tapping screws.

Boards are attached to the resulting base seats. It is desirable to deepen the hats of self-tapping screws.

Then attach legs. They are attached to the seat supports. The lower tsargs help to fix the legs.

The finished product is covered antiseptic and varnish.

Simple bench #2

To make such a garden bench with your own hands, you will need concrete flower girls and boards. Flower girls are required to create the base of the bench. Use two with a rectangular base and two cubic ones.

In order for the base to be stable, the flower girls must be glued or connected from the inside with staples fixed with self-tapping screws. A layer of drainage and soil is poured into the tank. This increases their stability.

The seat for the bench is made of boards. To do this, they are cut into segments of the desired length. These blanks are laid so that they have a distance of half a centimeter. Then they are connected using cross bars. Planks are placed in three places: along the edges and in the middle. Corners are attached to the planks. With their help, the seat will be fixed on the flower girls.

Do-it-yourself bench with a back

Prepare the details of the bench shown in the figure. They are processed antiseptics before connecting.

Then the supports are assembled from the parts. Pre-round the corners and chamfer. First, parts A and B are connected with a bolt, and then B, C and D are also connected using a bolt.

The inclination of the backrest is determined by part D, after which it is connected to part A. Similarly, but in mirror image, another support is made.

After that, the back and seat are assembled. To do this, the supports are placed so that there is a distance of twenty centimeters between them. First, the front and rear bars are screwed to the supports, then all the others, and finally the stops are screwed.

At the last stage, the back of this bench is screwed.

Bench #4Another option for a simple do-it-yourself bench. Its length is one hundred and twenty centimeters. The height from the ground to the seat is fifty centimeters, the height of the back is also fifty centimeters.

The base is made from boards, whose thickness is five centimeters, and the width is from ten to twelve. One of the legs continues and is the backrest support. The supports are connected according to the “half-tree” method and fastened with bolts.

The basis for the seat is a bar fixed on self-tapping screws. The short legs on the back of the bench are colleted together to increase stability. The seat and back are sheathed with boards with a smaller thickness. The surface is painted or varnished.

A simple bench with a back for a summer cottage

The dimensions of the structure and wooden parts can be seen on drawings benches. If we consider how to make a bench with our own hands, then this option will be the most optimal in terms of the simplicity of the process and the result obtained.

Materials are best purchased already cut to size. If there is no such option, then you need to cut them yourself.

The resulting blanks polished. The ends of the boards are treated with an electric planer.

The rear legs of this simple do-it-yourself bench are also a support for the back. To create the desired level of inclination, the blanks are marked.

At a height of forty centimeters mark the place of attachment seats. Above the board is cut at an angle of twenty degrees. The cuts on the two blanks should be the same.

Gather first legs benches: the front ones are connected to the back ones with a beam. It is better to do this from above and below.

When the side parts are assembled, they can be connected to each other with seat boards. Screw the boards with self-tapping screws, leaving distances of one or two centimeters.

To strengthen the structure and increase its stability, make the lower strapping bar on the legs. Two boards are attached to the back.

Finish the work with a finish coated which will protect the product from moisture and adverse conditions.

Do-it-yourself pallet bench

Make a bench with your own hands pallets It's easy if you use your imagination. To do this, you need three or four of these wooden structures. Some will need to be cut to get additional details. The simplest do-it-yourself pallet bench design is when two pallets are attached perpendicular to each other, creating a back and seat.

So that the design does not turn out to be too cumbersome, it is better to cut the pallets to the desired dimensions. Fasten the elements with self-tapping screws. Add side details that enhance strength and make legs. All this can be seen in the photo.

Since the material of the pallets is raw, rough, it will need to be preliminarily grind. This will allow you to do without splinters.

The manufacture of benches with their own hands from pallets is being completed with varnish or paint.

Bench puzzle

You can make such a bench with your own hands if you have a wide board and shovels for shovels. Figured seats are cut out of the board in the form of puzzle pieces. Legs from cuttings for shovels are attached to them. Separate stools are obtained, which are quickly assembled into one long bench. All manufacturing steps are detailed in step-by-step photos.

Benches from unnecessary chairs: two do-it-yourself options

First option

To create such a bench for a summer house with your own hands, you will need four old chair.

From the first two chairs filmed parts on the front of the seat.

The rest sawed off the front legs are slightly lower than the seat structure.

From the resulting details you need take off old varnish or paint. To do this, a special agent is applied to the parts that dissolves paint and varnish coatings. Then the softened layer can be removed with a spatula.

The racks should drill dowel holes. Holes are required on the front and end sides.

The dowels are smeared with glue and inserted into the drilled holes.

When the dowels are glued, you can collect base benches. To make the design durable, the parts are fastened with self-tapping screws. Construction surface sanded.

For seats benches choose a board that is suitable in size, saw off the excess.

If several narrower boards are used, then they are glued together with wood glue. For a tight connection, they are clamped with clamps and waiting for the glue to dry.

The finished seat is also glued to the base with wood glue. Heavy objects are placed on the board and clamped together with the base with clamps.

When the glue dries, cover the seat with masking tape and stain other structural elements with wood paint.

The adhesive tape is removed and the seat is processed wood stain. In conclusion, the entire bench is varnished.

Second option

To make a second garden bench with your own hands from old furniture, you will need two chairs. It is better if the back and hind legs are not separated.

Two identical chairs clean up all parts of the structure except for the rear legs with a back.

take bars 5 cm wide and 3 cm thick. Two pieces are cut off, equal in length to the width of the chairs, and two pieces of the same length as the finished bench will be. From these four parts, a rectangle is assembled. It is fixed to the backs of the chairs with self-tapping screws.

Another frame is assembled in the same way. Several cross bars are attached to it. This design is attached under the seat, makes the bench more reliable and plays the role of a shelf.

If the chairs are old coating then remove it with sandpaper. After that, the surface is puttied with a special compound or coated with a primer. When the layer dries, it must be sanded with fine-grained sandpaper. At the end, the structure is covered with paint.

Do-it-yourself seat for a garden bench is made from Chipboard or plywood. A rectangle is cut out of the selected material, which is larger than the base by half a centimeter on each side. Then cut out a piece foam rubber with the same dimensions. A rectangle is cut out of the upholstery fabric. It should be larger than the seat by five centimeters on each side.

Foam rubber is laid on a sheet of plywood, it is covered with a cloth on top. The fabric is fastened from the inside with furniture stapler.

The seat is attached to the base with a piano loop.

Bench-swing

To make such a bench for giving with your own hands, you should prepare the necessary materials. Start manufacturing by creating basics designs. The seat bars are attached to the back bars at a selected angle.

Along the seat install additional ribs providing rigidity.

Attached to the seat planks, drilling holes in the base bars for fastening. The same goes for the back.

Armrests are installed on both sides of the seat. They can be bolted on.

The resulting bench cover wood preservatives and varnishes. It is very important to paint over everything as carefully as possible.

The bottom of the bench is reinforced with metal profile. Chains are attached to the profile, on which the swing bench will be suspended. Be sure to check the reliability of the beams on which the bench will be suspended.

log bench

To make such a bench with your own hands from wood, you will need chainsaw. A thick log one meter long is taken as the main material.

Log mark out, to get two slightly unequal parts. The back will be made from the smaller one, and the seat from the larger one.

Chainsaw log sawed along the mark. The resulting irregularities are immediately cut off with the same saw.

The cut triangular piece is cut into pieces and inserted into the holes in the seat. The back is fixed on top. The bench is almost ready. It remains only to give it a more decorative look.

Can the seat be placed on legs. To do this, recesses are made in the lower part for installing a pair of logs as legs.

Bench-transformer

Design features of the transformer can be seen in the drawings of the bench. A do-it-yourself transformer bench is made from planed boards, which is cut to the named sizes.

In sliced lumber details holes for fasteners are drilled.

At the tabletop, boards located on the edge can be made wavy.

In material intended for countertops, drill holes with a diameter of twenty-two millimeters and a depth of three centimeters. Cuttings of the same diameter will be inserted into them.

The edges of parts and edges are processed and rounded.

The assembly of all elements is carried out with screws and screws. Screws are needed with dimensions 6x70 and 6x90, screws - 8x80.

Wooden parts stain stain.

The structural parts that will move are connected by hinges.

Between the boards of the tabletop place parts of a round cutting.

Set the stop for backs.

A do-it-yourself transformer bench is covered varnish.

rocking bench

Making an original bench with a backrest with your own hands is not difficult if you have the tools and materials. First you need to consider the drawings of the bench, which contain a small amount of detail.

The side parts according to the pattern are transferred to euro plywood three centimeters thick. They are cut with a jigsaw and the ends are processed with a grinder.

To fix the connecting strips, markings are made. Then holes are drilled. After assembling the frame, the rails are fixed with self-tapping screws. The attachment points are spatulated, and the product is completely varnished.

Bench around a tree

The simplest version of such a bench - hexagonal. The size depends on the size of the tree. Measurements are made at the height of the seat. To the result obtained, another margin of fifteen to twenty centimeters is added. If you divide the result by 1.75, you get the length of the inside.

For cutting boards ten centimeters wide are laid in four rows at intervals of one centimeter.

The cut point is marked immediately for all rows with an angle of thirty degrees. So cut out six sets of blanks.

Legs are used with a height of sixty to seventy centimeters. They are connected by crossbars by drilling holes and using bolts with nuts.

The seat is installed so that the joints are located in the center of the ribs of the legs. Screw the outer pieces first, then the inner ones. In this way, the entire hexagonal structure is assembled around the tree.

At the end, they make a back and mount an apron. The result is a circular bench with a do-it-yourself backrest.

The finished product is processed oil impregnation.

Bench made of curved branches

A bench made of curved branches will look original. For you will need branches for the front, two legs, a horizontal top and a pair of transverse branches.

Sawing branches so that they match each other as accurately as possible. Then they are connected with metal corners.

Similarly, the back is made and connected to the front.

The finished product is placed on a flat area and the seat is assembled.

Bench options

• log bench which blends in well with the natural environment. It consists of half a log used for the seat, and two short round logs that are legs.
  
• Beautiful wooden bench with a back and armrests, reminiscent of a sofa. Curved and carved elements make it more attractive, while left knots and bumps give the design a natural look.
  
• Bench made of wood and metal. The base of the structure is metal. The wooden parts of the seat and back are fixed to it. Due to the small thickness of the metal parts, it looks light.
  
• A bench of a simple, classical form. It is made of wooden, rather wide boards. This width allows you to comfortably sit on the bench. Armrests make the design more complete.
  
• original bench made of wood with curly details. This option is well suited for a site with a natural rural design. Carved legs and armrests, figured back - all this gives the product originality.
  
• Bench with an interesting back. The curved parts gradually deviate back, creating a unique design. The seat is slightly curved but has a more traditional look.
  
• Wood complex- a table with two benches. The design looks traditional due to the material used. The original solution is to fasten all the components into a single structure.
  
• The bench is made from solid wood. A single piece is cut out of it, combining the back and seat. The legs are attached to the bottom. The log is required quite large.
  
• Bench with storage box for toys. Outwardly, it looks like an ordinary wooden bench-sofa, but under the seat it has a drawer in which you can put various things.
  
• Comfortable wooden bench with a simple shape. The base is made in the form of a rectangular box. The back is also simple with a straight shape. The seat is padded with soft cushions for added comfort.
  
• A wooden bench placed around a tree. It is made as if it consists of four benches, each of which has one armrest. The composition looks attractive and comfortable.
  
• Bench of a simple form from wide boards. It looks solid, but its size is somewhat hidden by the gaps between the boards and the light blue color in which it is painted.
  

In a country house or in the country, every person wants to have only high-quality and multifunctional garden furniture that will not take up much space, and at the same time will perform maximum functions in the garden. Therefore, a transforming bench will be an excellent solution for a joint tea party with the family. Here you have both a bench and a table at the same time, and most importantly, you can make such a design with your own hands.

Bench-transformer - design description, principle of operation

Such a bench for a country house is a fairly simple design that can easily be transformed into a table with two comfortable benches. And when folded, it is an ordinary bench with a back and handrails. It will not take up much space on the territory of the personal plot and at the same time will be able to perform all its functions in full.

Functions and convenience of the bench

This is a compact and practical bench that easily turns into a fairly roomy table and two comfortable benches. Due to the high degree of mobility, it can be installed anywhere in the garden.

The only drawback of such a bench is its rather large weight, since it will take a lot of wooden boards to manufacture such a complex structure, but it will be quite stable, reliable and durable if everything is done correctly and accurately according to the developed instructions in compliance with all technological processes.

Preparation for the construction of the structure: project drawings with dimensions

Before you start building a bench - a transformer, you need to prepare all the materials and tools, as well as make a good drawing or find it on the Internet.

We offer you a typical drawing - a diagram of a bench - a transformer with the dimensions indicated on it. The most difficult action is the creation of a movable mechanism, so initially it is necessary to prepare all the blanks, which will then be assembled together into a single transformation structure.

To make a bench - transformer will need to purchase planed edged boards and timber. Larch, birch, pine, beech, ash or oak are best suited for such a design (if possible, since it is very expensive).

The board must be well sanded, of high quality and meet all compliance standards. If you buy a board at a sawmill, be sure to ask about the quality certificate for their products, since under the guise of an oak edged board, they can sell you a completely different product, and if you are not well versed in wood, it is best to take a carpenter with you who understands the types boards and their quality.

Material calculation and tools

To assemble a bench - a transformer, we need:

• Two beams with a section of 90x45x1445 mm;
• Five bars with a section of 90x32x1480 mm;
• Two beams with a section of 90x45x1445 mm.

To work, we need the following tools:

Stages of making a bench-table

1. The first step is to make the legs of the frame. To do this, you need to cut out 8 absolutely identical bars 70 cm long and make oblique cuts (also the same) on them at the bottom and top, so that you can get perfect balance when you further install the structure under a certain slope.
2. Next, we make a frame for two benches from a polished edged high-quality board. We cut out four segments of 40 cm each and the same number of segments of 170 cm. On all boards, the corners must be cut so that then two completely identical rectangles of a slightly oblong shape can be made. For their joining, we use special prepared screws or nails. But first, we drill the same holes in the boards with a drill (the length of the boards is 1.7 meters).
3. In the frame of the structure, several strong reinforcing elements must be made, which will further form a comfortable seat. To do this, we take a wooden beam and nail it in increments of 500 mm. So we will divide the structure into sections and protect the future bench from lateral deformation.
4. The legs must be screwed to the seat at a distance of 10 centimeters from all corners diagonally. We do this so that the joints are near the "seams" or a little further. Here it is very important to make the highest quality structural elements, that is, fasten them to 2 or 3 bolts that pass through the timber and the upper part of the prepared legs. It is necessary to make grooves in the beam in which we will hide the bolt heads. And under the nut, we cut off the excess with a hacksaw.
5. Next, we make a rectangular element of 70x170 cm from the beam, which we connect from the inside with additional details that ensure the rigidity of the structure. In the future, we use this element for the device of the back or countertop.
6. At the moment, we do not cover the frame with shields, as it will be difficult to assemble the entire mechanism into a single whole. It will also complicate the transfer of the structure.
7. We combine the three resulting elements into a common system. This work is quite difficult, since it will be necessary to work with large parts of the future bench - transformer. It is best to do all the work on a flat floor or on a special large table. We make all connections movable and fasten them with hinges or ordinary bolts.
8. We cut off two bars 40 cm long to fasten them between the bench and the table shield in the corners. They will be at the bottom of the shield, but on the side of the bench itself.
9. We cut off two more bars 110 cm long to make the back inclined. We fasten them with screws or other fasteners at another bench, but in this case, the fasteners are not placed on the near side, but in the very center. Otherwise, we will not be able to correctly connect the two benches together.
10. After we assemble the entire structure, and carefully check the operation of each moving element, it will be possible to start sheathing the frame from the outside. To do this, we take a well-sanded edged board, but you can take a bar or chipboard (if the bench - the transformer will not constantly stand on the street). Thus, we have completed the technical stage of the work.

The bench - a transformer can be covered with a stain and then with a water-repellent varnish, which is used to paint the decks of yachts. The varnish dries about 36 hours. But still, a varnished bench is not recommended to be kept outdoors in the rain and snow.

If the design is done correctly, and you take care of it, then it will serve you for at least 20-25 years. Very often, craftsmen replace wood with metal, which does not look so beautiful and aesthetically pleasing, but the service life increases significantly.

The second version of the transformer bench made of metal profile and wood

Materials and tools for construction

A bench - a transformer made of a metal profile is made similarly to a wooden one, but only with some changes.

To make such a bench, we need:

Construction steps

1. We clean all metal profiles from rust so that later it would be easy for us to work with the material - to weld pipes and paint them.
2. And then, according to the drawn up drawing, we cut the blanks size to size.
3. We make a seat frame. To do this, we weld the pipes as shown in the figure and, if necessary, strengthen the structure.
4. In the future, this design will serve as a table, as well as the back of a bench. We also had to change the angle a bit.
5. We weld another seat.
6. After carrying out all welding work, we begin to drill holes and twist everything onto special furniture bolts (their length must be at least 60 mm). Then we insert washers between the iron elements of the structure so that it unfolds more easily.
7. Here we see the final version of the transformer bench, where an additional strong leg was added to one of the benches and the angle and lunge of the leg in the second bench were slightly changed, since the angle of inclination was changed in the back, and it became steeper. In order for the bench not to be thrown, it was necessary to digest the structure.
8. For the legs, we cut out “heels” measuring 50x50 mm from a metal sheet so that the bench is more stable and does not “sink” into the ground if it stands on soft ground.
9. Depending on the size of the structure, we cut the boards and grind them well. These will be our bench seats and the surface of the table.
10. As a result, we get an excellent finished bench design. - transformer.

Shop decoration

Then we soak all the boards well with an antiseptic, fire retardant and let them dry. We paint with water-repellent varnish, oil or acrylic paint. We apply varnish or paint in several layers.

One of the advantages of giving - the opportunity to spend time outside. And you can’t do without a table, because how else can you dine in the fresh air? Yes, and kebabs are more pleasant to eat right by the fire, without entering the house. Therefore, a table in the yard is a must! And since we are in crisis times, and you can’t buy everything, it’s better to make a table with benches for a summer residence with your own hands. It’s cheaper, and the thing will turn out to be unique, and it will be about a hundred times more pleasant to use it.

Table with benches: design options

Basically, there are two ways to make a table with benches. The first way is to make a monolithic product in which the table and benches are a single whole.

The second option involves the manufacture of benches as separate items. Then you can use them on your own. But no one forbids these approaches to combine.

We make a table with benches with our own hands

Wooden table with benches

We will focus on the first method and show you the easiest way to make a table with benches made of wood.

First of all, the table cover is assembled. As you can see, its design is extremely simple. Boards are simply fastened with self-tapping screws to three crossbars.

Then the legs are attached to the crossbars on the lid. Please note that the legs must be made of a thick board (40mm or more) or timber. They must be durable, because with such a design of the product, it is they who carry the weight of not only the table and what is on it, but also the weight of all the people who are sitting at this table.

Next, we attach the crossbars to the legs, on which the boards of the benches will be laid. They perform a dual function: on the one hand, they carry the benches, and on the other, they give rigidity to the entire structure. They must also be durable. And it is better to fix them not with self-tapping screws, but with 10-12mm bolts (two or three bolts on each leg), because it is this fastener that will take on the weight of those sitting.

It remains to attach bench boards to these crossbars, and the table with benches is ready.

We paint with transparent paint to be able to see the beauty of the texture of natural wood.

Admittedly, this design has some drawbacks. Firstly, if people sitting on one side suddenly stand up together, then those sitting on the other can outweigh and overturn everything that is served on the table. In addition, the crossbars on which the benches are held make it difficult to disembark and board. Such is the price of simplicity.

But the table in the photo below is devoid of these shortcomings, because. firstly, the table supports are on the same vertical with the center of gravity of people sitting on the bench (which, moreover, has its own legs and therefore does not load the table supports at all), and secondly, the benches are attached to the table in the middle, and not on the sides which makes it easy to sit down and get up from the table.

This photo shows how the frame of a similar table is arranged, though without supports under each seat, but they are not needed here, because. the table supports are again almost on the same vertical with the center of gravity of those seated.

If your loved ones have people with special needs who move around in a wheelchair, you can take this into account when making your table. They will appreciate it!

Bench with a table on a metal frame

If you're a bit of a welder, you'll probably find it easier and faster to weld a metal table frame than to fiddle with wood.

Metal frames are thinner and more reliable, so the whole structure takes on a less bulky, almost elegant look. At the same time, you can get rid of the shortcomings that are inherent in our very first design.

In addition, the strength of the metal allows you to move away from the usual forms and give free rein to fantasy.

And of course, you can go the way of benches not attached to the table.

Table with benches on a metal frame without welding

If you liked the idea of ​​a table on a metal frame, but you don’t have welding or you don’t know how to use it, don’t rush to get upset!

These tables are assembled without a single weld! All metal elements are simply bent into shape and fastened with screws.

We have shown you several ways to make a bench with a table for your garden. Which of them should be preferred? Wood has its own special charm; metal is easy to work with and allows for more practical and less bulky shapes. This choice is yours!
In any case, your table with benches will turn out to be unique in its own way, because handmade things always bear the personal imprint of the master who has put his soul into them.

We hope that at your leisure you will also think about how to make your own project of a table with benches for your favorite dacha.

The dining area or recreation area in the country is important for every member of the family, as here you can sit with a book, eat lunch prepared by your mother or a barbecue that your father fried.

Here you can gather with the whole family to spend a summer day or evening drinking tea or just having interesting conversations about something important and urgent.

Manufacturing steps

Step 1. With the help of a self-tapping screw, using the method of sampling half of the board, fasten the crosses of the table legs.

Step 2 The next step is to make a selection of wooden boards. Find the middle on the board and carefully cut special grooves with a hacksaw. After that, the cut is made to the middle.

Step 3 The wooden bench must be securely attached to the table. Therefore, to assemble all the elements of the table and bench, as well as to fasten these two pieces of furniture, metal rods, nuts and washers are used. They must be well tightened so that the details of the structure do not loosen.

Step 4 Now you need to fix bottom table using screws and nails.

Step 5 Assembling the tabletop is very easy. You must first make a frame of bars located around the perimeter, and then attach polished boards to them.

Step 6 Attach the tabletop to the cruciform parts with self-tapping screws.

From logs, a table with benches is made according to the same principle as from boards. Only fastening must be done with brackets that will securely connect large and round elements.

The assembly scheme for such a table must also be prepared in advance in order to know during the process which parts, to what and where to attach.

When making a wooden bench table, all movements must be performed carefully and carefully so as not to spoil the tree. Sawing parts should be strictly in size, marking the place of the cut with a pencil.

Bench-transformer

A transforming country bench is an original design that will be appropriate in a garden, gazebo or in the shade of branchy trees.

At first glance, this is an ordinary bench that can turn into a comfortable and large table in a few seconds. Such a piece of furniture can be made independently using ordinary improvised materials.

The transformer bench consists of five main elements:

• metal frame base;
• back, which;
• fixing element for the tabletop;
• wooden seat;
• seat holder.

Manufacturing steps

frame

The frame base can be made from a square metal pipe with a section of 25 x 25 and a wall thickness of 2 mm or a round metal pipe with a diameter of 17 mm.

You will also need wooden plugs in the form of plugs. The pipes are welded together, and wooden plugs are inserted into the pipes at the ends.

Important! To make the structure strong and reliable, it is necessary to weld metal inserts in the form of a triangle in the corners.

backrest

You will need plywood up to 20 mm thick and a wooden block 40x40 mm or 50x50 mm in size. The bars are nailed in width in the amount of 3 pieces using small nails or screwed with self-tapping screws. If there are any irregularities or roughness on plywood, then its surface must be sanded with fine-grained sandpaper.

Tabletop retainer

This element is made of thin lath boards. They must be attached to each other with a thick metal wire with a diameter of 10 mm.

Wooden seat

The bench of a transformer consists of sitting and a clamp. For the manufacture of the seat, it is necessary to prepare a wooden block 30 x 30 mm and boards 60 mm wide. One plank should be 10–15 mm shorter so that the latch free stood between these two.

seat latch

The lock for the bench is best made from metallic wires up to 14 mm in diameter.


Self-assembled garden furniture can become original garden addition or yard near the house. Can be done this way two table-bench or table-transformer and put them next to each other. Get a great place for tea drinking and celebrations where possible place a large number of relatives and friends.

Finishing the table-bench

In those places where screws were installed and nails hammered, you should use a special wood putty. Apply and spread the mixture with a rubber spatula.

When the composition hardens, grind all the missed areas with fine sandpaper. Before that, it must be fixed for convenience on a bar.

Finishing is of great importance for wooden products that are planned to be used outdoors.

If not done, then the service life of country furniture can be minimal. Lacquer is perfect for finishing. It can be tinted or completely transparent.

Note! If noble woods with a pronounced texture were used to create furniture, then oil or drying oil of a natural shade should be used.

Regardless of the selected finishing material, it must be applied carefully and in two layers, brushing all surfaces with a brush, and not just those that are visible. After varnishing, the surface can be additionally covered with a weather-resistant furniture coating.

Metal elements in the transformer table should be treated with an abrasive wheel to remove welds. After that, it is necessary to apply a paint and varnish coating that will protect the metal from corrosion.

Thanks to this finish, all wooden and metal elements of the table-bench will be aesthetically beautiful, and the bench itself will turn out to be reliable and durable.

For more information on how to make a transforming bench made of metal and wood with your own hands, see the video:

Such garden furniture is a vivid example of a successful combination of beauty and practicality. Isn't this especially appreciated in a private house or in a country house, where there is often not enough free space?

When folded, the design takes up very little space. (photo 1). And with a flick of the wrist, an ordinary bench turns into a table with two benches - great for outdoor dining or for board games with children. (photo 2). Building material: timber with a section of 90 × 45 mm, 90 × 32 mm, 45 × 32 mm. Hardwood is preferred: beech, ash, oak, birch (in extreme cases, pine without pronounced knots).

Instruments:
■ desktop end machine - its limb with graduation will allow you to get accurate cuts of parts (or you will have to make markings with a protractor and cut with a hacksaw with a fine tooth);
■ electric drill and drills: spiral d 5.1 mm, d 3.0 mm (holes for screws), 8.0 mm (holes for dowels), feather d22 mm (holes in parts moving relative to each other);
■ countersink (recesses for screw heads);
■ Phillips screwdriver;
■ milling machine or hand planer (chamfering on the bars that form the planes of benches and tables);
■ grinder or bar with sandpaper (finishing the surfaces of parts),
■ rasp (rounding corners).

Auxiliary materials: wood glue PVA, paint (impregnation), sanding paper No. 60, 80; wood screws; wooden dowels - 12 pcs. (connecting parts D-D1, Zh-Zh1); M8x60 mm bolts with self-locking nut and washers - 4 pcs. (connection of parts A-K, D-E).

Manufacturing

Children have P and C we chamfer, i.e. round off both edges on the wide side of the bar. Children have P, forming the plane of the tabletop, we remove one chamfer from two bars, which during installation will be extreme on both sides of the tabletop. In children. A and K, when marking the centers, we first drill through holes with a d5 mm twist drill. Then, conditionally gray children. legs A and the support bar L of the tabletop, from the outside we drill a recess under the bolt head with a pen drill. After that, we drill the centering holes with a d10 mm drill. We do the same with children. D and E. In children. We drill a through hole.

Details of the transformer bench
Items not shown in the figure:
P- Bars for countertops - 90x32x1480.5 pcs.;
R- Bars for the outdoor bench (in the folded position) 90x45x1380 mm, 2 pcs.;
With- Bars for the inner bench - 90x45x1445 mm, 2 pcs.