Making corners in the apartment. Empty corner in the apartment - how to decorate or what to do

Flat corners - sign of a quality repair. However, this result is considered to be the exception rather than the rule.

Often, uneven corners can greatly spoil the impression of the repair work done, since as a result of this drawback, significant visual distortions of the finishing finishing material are possible.

Aligning wall corners is important final element of wall finishing works. How to align the corner of the wall with your own hands, we understand in this article.

Joints are a rather difficult area to process: to make perfect 90-degree corner surfaces, you will have to put a lot of effort and care.

Do-it-yourself wall alignment - myth or reality?

It is generally accepted that do-it-yourself wall decoration is much easier than ceiling correction, but this statement is only partially true. Often the reason why angular irregularities can occur is poor quality plastering.

If certain deviations of the corner surfaces are found, they should be eliminated before finishing the walls.

This is especially true when it is planned to stick wallpaper with a pattern in the room or install ceramic tiles - with such finishes corner surface defects will be obvious.

Depending on the type of finish, a method is selected - it can be done either with the help of GKL or with the help of dry mixes. Irregularities in corner spaces are corrected using the method of alignment by ledges or by level.

First option most preferable in the case when it is planned to paint the walls or finish with a decorative layer of plaster. Second option acceptable when subsequent wallpapering is expected.

Aligning corner spaces on your own may seem like a very troublesome and almost impossible task, but this is not so.

Subject to certain rules and the availability of the necessary tools, correction of wall joints will be possible even for a beginner.

Corner surfaces can be leveled using plaster or putty, drywall sheets and a perforated corner with a mesh.

Wherein alignment with GKL is not recommended in the event that the finishing will be laying ceramic tiles or porcelain stoneware: a surface that is too smooth will not ensure strong adhesion of the finishing material to the base.

Ideal angle: how to measure skew and achieve 90º?

Sometimes it pays to think- Is it so important to bring wall joints to perfection? To answer this question, you need to understand how important it is in this case to clearly set the corner joints at 90º.

In some cases, when only a cosmetic update of the interior space is planned and no additional costs are expected, the alignment of wall joints can be omitted.

In other cases, setting 90º is essential part of the renovation, since some modern furniture and appliances require only such a base.

Once the alignment decision has been made, the angular misalignment must be carefully measured.

To determine the vertical skew, it is enough to attach a ruler or rule vertically to the corner.

Next to the ruler is to lean the spirit level, which will help to visually determine the value of the distortion along the wall. After the work done, it is necessary to measure with a ruler the maximum skew from the vertical of the corner or wall - as a result, the desired value will be obtained.

In the same way, one can measure deviation from an equal angle in the horizontal plane, however, in this case, a longer ruler or profile is needed: horizontal distortions, as a rule, are of less importance, so a greater distance will be needed to measure them.

In the case when it is impossible to visually determine the skew, you will need a profile with a length of at least two meters.

You may be interested in the features of applying liquid wallpaper to the wall.

Varieties of materials for work

The most common and effective alignment methods are varieties in which dry mixes and drywall sheets are used. Quite effectively, the method of eliminating defects with the help of a perforated corner has also proven itself.

To find out which method will be effective in each case, you need to consider each of them in detail.

With putty or plaster

In order for the corner correction to be successful, you need to work use high quality blends made by trusted manufacturers.

Perhaps the price tag for these mixtures will be slightly higher than unknown brands, but there will be no doubt about the quality of the work done.

The most convenient way to work involves gypsum plaster or starting. This option will allow you to make a correction using the thinnest layers and at the same time without subsidence.

To perform this type of work, you will need the following tools:

1. Roller or brush for priming the base;
2. Spirit level of any type, as well as a plumb line;
3. The container in which the plaster will be mixed;
4. Drill mixer;
5. Rule;
6. Wide and narrow spatula;
7. Primer for the base;
8. Dry mix for leveling.

Before starting work, you must to carry out priming of wall joints with a solution of deep penetration. Next, you need to calculate the required amount of plaster mixture.

Alignment by level must be done in the case when the surface will be finished with tiles of any kind. In the case of painting or gluing, alignment along the plane is sufficient.

The choice of mixture depends on outside or inside finishing work will be carried out. If you plan to finish corners located outdoors or in rooms with high humidity, you should choose a mixture based on cement, lime mixtures and polymers.

In the case when it is necessary to correct internal joints, plasters based on a gypsum mixture can be used.

Work procedure consists of the following steps:

In the case when the walls are erected evenly, the angle after alignment turns out by itself. For more convenient work you can use a counter- a special metal corner with perforation.

The plastering method is used when the angle misalignment is insignificant and does not exceed a few centimeters.

If the distortion turned out to be impressive, it is better to use drywall sheets.

Video instruction on how to properly putty corners:

Gypsum board as a means of achieving an even joint

Gypsum boards for leveling corners are a very effective tool. They apply when when leveling with plaster cannot give a quality result and have many advantages over plastering:

• GKL do not require the removal of old wall coverings;
• Do not require kneading dry mixes and the whole process proceeds without dirt;
• Drywall plastering can be carried out immediately after installation.

Among the disadvantages of this type of finish, one can single out the relative brittleness of the material and its instability to serious mechanical damage. In addition, GKL is not used in rooms with a constantly high level of humidity.

If the walls of the room were originally lined with gypsum plasterboard, no adjustment of the corners is required. In the case when it became necessary to equalize the walls with drywall, it is necessary:

1. Carry out the installation of guides that will serve as the basis for drywall sheets;
2. Sew up the GKL frame with self-tapping screws or screws;
3. Apply reinforcing tape to reinforce internal corners;
4. Align perforated aluminum corners for outside corners;
5. Putty the joints.

A heavily littered wall requires the use of a combined method, which includes both plasterboard finishing and leveling with a plaster layer.

Perforated corner with mesh for perfect 90º

The leveling corner is used where it is necessary to strengthen the outer and outer corners. In addition, this material greatly facilitates the work of exhibiting perfect corner joints. In any case, the corner in which the perforated corner with the mesh is mounted will turn out to be perfectly even.

In order to expose such a corner, you need:

To make the transition to the corner from the wall invisible, you should plaster it with an overlap with the wall and smooth with a wide spatula.

Internal corners: features

For interior corners in the apartment, you can use both dry mixes and sheets. Before plastering, it is necessary to check the evenness of the corner joints using a plumb line and level.

If there are protruding bumps on the surfaces, they can be removed with a hammer or chisel.

After preparing the surface, it is primed with a special deep penetration compound. This method will make the corners stronger and improve the adhesion of the new plaster layer. The primer must be made along the entire length of the rule.

Even corners when plastering will provide special beacons. They need to be placed right in the corner space.

Lighthouse - a strip of gypsum solution about 5 centimeters wide. The mixture for beacons should not contain lumps.

The solution for the beacon is applied in a strip on one side of the corner joint, after which it is leveled using the rule.

After the first beacon dries, you can install the next one on the opposite side of the corner. Subsequently, it is necessary to align the angle completely with a special angled spatula.

The outer corner of the walls - how to achieve an even joint?

For external leveling work drywall is not used. For external corners, only dry building mixes are suitable.

1. First you need to check the outer corners for evenness. All protruding irregularities must be removed with a hammer.
2. The next step is the priming of the walls with the help of special deep impregnation compounds.
3. For reinforcing external corner joints perforated metal corners must be used, which will strengthen the joint and help avoid damage. They are pressed into the gypsum mortar and subsequently leveled with putty.
4. Excess mixture must be removed with a spatula. Then you need to make sure the exact vertical installation of the metal profile.
5. With the help of gypsum beacons on both sides, the angle is leveled and puttied.

Different ways to align outer corners are discussed in the video below:

Conclusion

Aligning corners with your own hands is a painstaking task, but it is not difficult. For high-quality work, it is better to use proven finishing materials. When performing work, patience, accuracy and care must be exercised.

Immediately it is worth explaining that the corners are external and internal. The first, as it is not difficult to understand, are mounted on top of the finish, and the second under it. This means that the functionality of the elements is slightly different. Both types serve to protect the outer corners from impact, while the outer ones additionally carry an aesthetic message. There are also corners and internal ones that protect not from impacts, but from deformation changes in the base of the walls, while keeping the exterior finish intact. Let's take a closer look at each type of corners.

Table 1. Varieties of plastic corners.

Corners, photo	Description
	The perforated corner belongs to the category of internal - it remains in the layers of plaster or putty, which means it is invisible to the eye. Perforation is needed on it so that the gypsum mixture passes through the holes, thereby fixing the element more firmly. Theoretically, such corners can be used for internal and external corners, but in practice only for external ones. The fact is that they have an uneven geometry (the angle is somewhat sharp) and at the same time it is normal to spring like that when you try to unbend them a little. And if, when mounted on an outer corner, it can be additionally fixed in the desired position with a masking tape, then such a number will not work here. This corner helps to make the corners more even. In the event of an impact, the outer layer of putty can fly off from them - all this is quite simple to restore.
	This version of the perforated corner will cost you a little more, but it has an additional layer of fiberglass that will protect the corner even better. When buying, also look at the quality of workmanship if you need to reinforce the inner corner in the room. The undeniable advantage of plastic plaster corners is that they are not subject to corrosion. They can be safely used in wet areas, while their metal competitors will not tolerate the harmful effects of steam.
	Another type of corner is intended for framing and precise puttying of plasterboard arches, etc. Since the arches have no internal corners, the purpose of such an element is the only one. They can be used when puttying plasterboard ceilings that have curved sections. Advice! You can make such a corner yourself by cutting one side of a regular perforated corner in some increments.
	L-shaped corners are mounted on top of the trim. They come in different sizes, shapes and colors. Most often there are white corners, but you can also buy textured ones that imitate a wood pattern. To be honest, we have never seen other pure colors in stores. Such a corner allows not only to protect the corner, but also to make it visually more even and attractive. He will not allow, say, wallpaper to peel off in this difficult place, so the edging of a door or window opening will always look attractive.
	This corner is very thick. It is not made of plastic (PVC), but polyurethane. Both are polymers, so we didn't break them down into separate classes. The purpose of such a corner is exactly the same as that of the previous one, however, they are completely inelastic, so they need well-prepared corners.
	Another type of outdoor decorative corner. It differs from the previous options in that it can bend, as shown in the diagram on the left. This property makes it more convenient to use, especially if you need to mount the corner on an uneven corner. It can be used for both external and internal corners. The solution also has a drawback - there is a thin film at the junction of the blades, which can easily be torn upon impact.
	This version of the corner is designed to be used in conjunction with ceramic tiles. Its shape is such that the mounting tail must be immersed in the adhesive connecting the tile and the wall during installation. Such an insert is very useful - it will protect the finish from chipping, and more importantly, in the event of a head hit on it, which may well happen in the bathroom if a person slips, the falling one will be limited to a bump, and not a heavy cut. Such a measure can save someone's life.
	These corners are used by good tilers only at the request of the client. The fact is that their installation is problematic, and the corners rarely turn out beautiful. Often the surface of the tile is deformed, which is allowed by the standards in its manufacture, in another situation it may simply be an uneven wall. All this leads to the fact that it is impossible to press the corner against the wall, and there are large gaps that you cannot normally cover even with grout.
	Such corners are mechanically attached to the frame, which is sheathed with plastic. They are both decorative and load-bearing structural element. Carefully cover the cut edges of the plastic panels. They are quite difficult to install, and the last corner is completely made from the start, since it is impossible to install the inner one.
	A corner similar in design, only for external corners.

There are some other models of corners, but they are very specific, so when decorating walls, they will not be needed.

Prices for various types of corners for protecting wall corners

Plastic corners to protect wall corners

Installation of plastic corners

So, in fact, we have three types of corner, which are mounted on different materials and for different purposes. Let's take a closer look at how to install each.

Hidden corners for putty

For work, we need the following set of materials and tools:

1. Perforated corner.
2. Putty or gypsum plaster, depending on at what stage you perform the installation.
3. Container for mixing the mixture.
4. A pair of spatulas.
5. Something for cutting corners, such as metal shears.
6. You can also use a construction stapler to pre-fix the part.

Step 1 - applying putty to the corner. Cut off the corner along the length and knead the putty in a bucket. Next, we collect it with a spatula and apply it directly to the corner so that it hits both adjacent walls. We pass in this manner the entire area on which the corner will be glued.

Step 2 - install the corner. We put the corner in place and press it into the putty. Press down better so that a minimal layer remains under the plastic.

Interesting to know! Plastic corners often have a bulge in the middle, which is why you need to build up a layer of putty in order to smoothly approach the corner. To prevent this from happening, the walls can be sanded, which will allow you to drown the part inward. You can’t do this on drywall, so we go as we go.

Step 3 - press the corner. The corner must be pressed from both sides at once. Use a spatula for this - this will allow you to align as accurately as possible in a plane with the walls.

Step 4 - level the putty. Then we draw a spatula along the corner and remove all the protruding putty, simultaneously leveling it and filling the voids. Make the edges as smooth as possible, but do not try to create a perfectly smooth surface - this is now useless. At this stage, you can check the evenness of the position of the corner according to the level and make adjustments if necessary.

Step 5 - stretching the corner. We give the starting layer of putty to dry, after which we proceed to leveling the corner. We need a small rule that will help smooth out the difference as much as possible, due to the protruding corner. We apply putty on the walls and stretch it, getting an even and beautiful angle. In principle, that's all, but if you wish, you can once again smear everything under zero with a spatula after this layer has hardened.

Due to the rigidity of the corner, we managed to achieve the correct geometry of the outer corner of the window slope, it is also possible to do this only with a trowel, but some experience is required, and such a corner will not be strong.

If you are not a supporter of whitewashed gypsum walls, but at the same time want to be able to change the look and mood of the rooms more often and at no extra cost, then why not look towards wallpapers that can be painted over and over again? In we will tell you how to paint wallpaper for painting correctly, strictly according to technology, so that they serve for a long time.

Prices for various types of putties

Putties

Video - Installing plastic corners

Installing external corners with glue

Do you think that it will be easier to stick plastic corners on glue than to wall up perforated ones into putty? You are deeply mistaken, since this work requires high accuracy in measuring and cutting material. Now you will see for yourself.

To work, we need the following:

1. Masking adhesive tape for pre-fixing parts.
2. Glue liquid nails and a gun under it.
3. A stationery knife with thick blades or metal scissors for cutting a corner.
4. Tape measure and pencil for measurements.
5. White silicone sealant to mask possible gaps.
6. Square for adjusting an angle of 45 degrees.

In the example, we will consider how the window slope is framed.

Step 1 - prepare the workplace. In order not to spoil the window sill (soil and scratch), it must first be covered with something. We have laminate flooring. We put all the necessary tools on top so that it is always at hand.

Step 2 - measuring the sides of the slope. With a tape measure, we measure the height of any of the sides of the slope. It is important to focus on the distance from the window sill to the edge of the horizontal side of the slope. Errors are not allowed, so measure everything to the nearest millimeter - use a good tool, not a rusty old one, on which you can’t make out the graduations.

Step 3 - marking the corner. We transfer the resulting dimensions to the corner and put a mark with a pencil. Make sure that the corner does not bend, otherwise you will get large errors. It is best to lay it on a flat surface and take all measurements in this position.

Step 4 - Marking at 45 degrees. We take the square and set it as shown in the photo, orienting exactly on the mark made earlier. We draw an oblique line along which we will cut the part.

Advice! It is also better to make the first mark in the corner, setting exactly 90 degrees, so as not to make a mistake when cutting.

Step 5 - cutting the corner. We cut our corner exactly along the drawn lines. There shouldn't be any questions here. The only thing is, if you use metal scissors, you can carefully trim the edges.

Step 6 - Apply glue to the back of the corner. We load a tube with glue into the gun and squeeze it onto the inside of the corner. We advise you to double-check the item beforehand, you may have made a mistake in the measurements. Glue can be applied in a continuous strip or do it pointwise.

Step 7 - gluing the corner. Then we apply the corner to the installation site and press it along the entire length. If you have glue sticking out of the edges, then immediately wipe it off with a damp cloth.

Attention! Do not use synthetic resin based compound. It can be washed off only with a solvent. You will definitely stain the wallpaper and putty with untidy yellow spots. Buy acrylic glue, you can also use silicone, but it will also be difficult to remove.

In exactly the same manner, we put the second vertical side.

Step 8 - preparing the corner up. It will take longer to tinker with the upper part of the slope. We need to accurately measure the distance from corner to corner, then transfer it to the workpiece and put marks. At the same time, we measure not from the edge of the part, but with an indent wider than the thickness of the corner. Next, ears are cut out on the corner, as shown in the photo. We do not mark the oblique cut, since we will do it after the fact.

Step 9 - simultaneous marking and cutting. We take our workpiece and set it on a slope, slipping the ears under the oblique sections of the vertical elements. Then a clerical knife with a sharp blade is taken - with it we carefully first outline the line, and then we go deep into the incision with repeated passes until we completely cut off the excess part.

As a result, we get a very even joint. If, nevertheless, the gap remains, then it can be easily covered with white silicone sealant. Next, the upper corner is removed, glue is applied to it, after which it is finally mounted.

Prices for different types of liquid nails

Liquid Nails

Video - How to glue plastic corners on slopes

Installation of corners for ceramic tiles

We already wrote that the use of such corners not only decorates the finish, but also makes the outer corners in the room less traumatic. For this reason, we advise you to always use them, especially since it is much more difficult to make corners from tiles with a 45-degree cut. In our work, we must take into account the following points

Step 1 - choose the right size corner. Wall tiles from different collections can be from 5 to 12 mm in thickness. Therefore, it is necessary to choose the right size of the corner. To do this, be guided by the numbers, choosing so that the corner is 1 mm larger, since you also need to take into account the thickness of the tile adhesive layer. Or take one tile and slide it into the cavity of the corner - it should fit into it and go inside a little.

Interesting to know! If the tile does not go inside the corner, you will not be able to hide the irregularities of its edges.

Step 2 - tiling one side of the corner. The corner has only one mounting flange, so it will only be held by tiles on one side of the corner. On the other side, it has a small protrusion, which should hide the edge of the tiled surface on the adjacent wall. From this we deduce the following procedure. First, one side of the corner is tiled, and it is desirable to leave the factory, not cut off side on the corner.

In this case, it is necessary that the resulting face be set strictly along the vertical level. Also, it should not protrude much beyond the corner (only 1 mm, it is better to check this by applying the corner on a dry one) or, conversely, not reach it.

The plane of the wall itself must also be level and not have differences throughout, otherwise gaps will appear between the finish and the decorative element.

Step 3 - prepare the corner. Then we take a tape measure and measure the exact distance, in the manner we did in the previous instructions. The corner also needs to be cut at a 45 degree angle, but this is difficult to do due to the rounded shape of the element. In work, we need a miter box in which we need to lay a corner, and, guided by the mark, cut the part with a hacksaw.

Advice! Immediately shorten the mounting part of the part by half a centimeter, as it may later interfere with docking with the horizontal corner.

Step 4 - fixing the corner. We install the corners in their place. In the example in the photo, the master is laying tiles on a gypsum fiber wall, so he fixed the frame with self-tapping screws with a press washer. This solution is temporary - the screws will be unscrewed as the corner is tiled. Alternatively, you could use a stapler with staples, then you don’t have to remove anything.

If your wall is concrete, then you can strengthen the corner with a thin layer of tile adhesive, which is applied before installing the element. You can do without temporary fixing, but then there is no guarantee that you can definitely combine the parts. Please note that the master with the photo did it perfectly.

Step 5 - cutting the tile and trying it on. According to the planned layout, we cut the tile, which will be installed on the second side of the corner. We apply it for a preliminary measurement and see that it cannot enter the corner. The fact is that all wall ceramic tiles have some narrowing at the edges. Some models even have a deliberately convex shape, and the difference can be up to 3-4 mm. How to act in this situation?

Step 6 - marking the back surface of the tile. Firstly, you can initially attend to buying a wider corner, but again, without cutting the tile, you won’t be able to measure it on the spot. Secondly, we can slightly reduce the thickness of the tile where it overlaps the corner mounting strip. To do this, first make a mark with a pencil on the back of the tile, then take a bar with sandpaper and clean off 1-2 mm of material. Of course, such work takes much more time from the master, but if you could not accurately select the size of the corner in advance, there will be no other way out.

Step 7 - fixing the corner. We proceed to the installation of tiles and the simultaneous fastening of the corner. We take the diluted tile adhesive and with a spatula gently press it into the perforation of the mounting plate. Do not make layers and immediately remove all unnecessary, as this glue will interfere with the normal sinking of the tile into the corner.

Step 8 - Applying glue to the wall. We spread glue on the wall using a comb bevel. You can also apply it and not a tile, but then you will need to remove the excess from the edge that we turned before installation.

Step 9 - gluing tiles. We glue the tiles. To begin with, we feed it a little forward with a turned edge so that it enters the corner. Then we press the second side and gently tap it on the surface. We align the plane with the rest of the already installed tiles and continue to move on, simultaneously unscrewing the screws so that they do not interfere with work.

Step 10 - additional fixation of the corner. When the tile adhesive dries, the corner will merge into it, and it will be impossible to remove it just like that, but while the composition is still liquid, the decorative element can be accidentally displaced, which will disrupt the structure of the adhesive. To prevent this from happening, we additionally fix the corner with pieces of masking tape.

Prices for different types of ceramic tiles

Ceramic tiles

Video - How to install corners on a tile with your own hands

Conclusion

So, we have dismantled the installation of three types of corners. We didn’t write about the options on the PVC panel, since everything is already very clear there - we fix the part in level on the brackets, insert the panels into it. The material turned out to be quite informative and voluminous. We hope you found the information you are interested in.

Today, decorative corners on the corners of the walls are an important element of decor. They help protect problem areas from mechanical damage. Their installation prevents damage to expensive finishes, gives the interior frame a finished look. Let's talk about where such elements can be used, what materials they are made of, how they are attached to the surface.

Source static.tildacdn.com

Scope of use

Corners are the most problematic place. When performing repairs, it is difficult to decorate them beautifully. Wallpaper pasted on them, after some time, lift up and peel off. When furniture is brought into rooms or when rearranged, solid large elements are often damaged, which leads to a sloppy appearance. All this can be prevented by purchasing decorative wall corners and installing them at the stage of finishing. They will completely close the ends with themselves, allow you to form a smooth transition from one material to another, cover up some of the sins of the painter's poor-quality work.

Decorative corners - an element of decor that gives the finish a complete look Source design-homes.ru

In addition to a purely technical function, the corners carry an aesthetic load. If you close the perimeter of the window opening with a white profile, the window will look better. This technique is often used when, according to design requirements, the window is not covered with curtains, but is framed with blinds. In this case, the color of the corner should match the color of the wall finish. When a contrast technique is applied, the profile acts as a separate element of decor. It immediately catches the eye and becomes an original part of the interior.

Source i0.wp.com

Designers love to use decorative corners for the outer frame of the doorway. This becomes especially relevant when the thickness of the wall is greater than the width of the door frame. This difference is completely closed by extensions, and then corner elements are superimposed on top of them, the color of which completely matches the color of the door.

Source skobdom.ru

The outer corners of the walls, arched openings, ledges and niches need additional protection. Installing corners will prevent the risk of damage from accidental impact. It is relevant when the walls are simply plastered or covered with wallpaper. In addition, it is easier to do cleaning and eliminate traces of hands. If the corners are closed with a plastic profile, it will be easier to keep clean.

Source sprofiles.ru

Corners can close the ends of the wall, finished with ceramic tiles or wall panels. Often in such materials, the edges remain unpolished, so the edge looks unattractive. Mounting the profile helps to completely hide such a defect.

Source profil-mo.ru

Another area of ​​application is the decoration of the outer corners of structures assembled using drywall. Today, the technology of creating open shelves, racks from this material is actively used. Joints closed with a profile look more aesthetically pleasing.

Arch, the corners of which are closed with a decorative corner

With the help of decorative corners, you can make a frame for large mirrors, close skirting boards with them, any joints that take the form of an angle. There are profiles for plastering, models for ceramic tiles, profile products for bathtubs, furniture.

Source 1decor.ru

Varieties of corners

The appearance of products and their technical characteristics depend on the material from which the profiles are made. It also defines the scope.

Source i.ebayimg.com

metal

For the manufacture of such corners, aluminum, brass or steel is used. Corners made of brass and steel have a smooth, well-polished surface. The aluminum profile is presented in three varieties. There are polished samples, anodized products, corners with a decorative coating on sale.

Source kantiere.ru

Most often, such products are used in the furniture industry, but designers also like to use them when the walls are decorated with furniture panels, MDF or chipboard sheets. In this case, a metal profile is selected, painted to match the base material. Unpainted metal corners are suitable for framing mirrors, paintings or posters placed under glass.

Source www.bradjenkinsinc.com

Craftsmen use metal corners to create the basis for the installation of light armstrong suspended ceiling structures. With the help of them it is possible to carry out the installation of light plastic panels. They can act as anti-slip pads or protect the edge of the structure from chips and cracks.

Source i.pinimg.com

Finishing wooden

Their main area of ​​​​use is the decoration of external or internal ends of walls sheathed with a block house, planken or clapboard. They are made from expensive or cheap types of wood, so they have a different price. They can be additionally painted and varnished, various patterns can be created on the surface using a milling machine.

Source static.tildacdn.com

Recently, designers like to use a technique that allows you to cover the ends of the wall, pasted over with wallpaper or painted with paint. This is only permissible if there are strictly straight surfaces.

Source avatars.mds.yandex.net

When choosing this finishing option, it is important to consider that a wooden corner is a fragile product, with the slightest effort it can break or crack. Excessive moisture or prolonged overheating can spoil its attractive appearance. Therefore, they should not finish the walls and window openings in the bathroom or in the bath.

Wooden corners - a fragile product

Wooden elements are fastened with wood glue or PVA glue. Liquid nails are suitable for the indicated purposes. If the walls are not concrete, you can also fix wooden corners with finishing nails. In this case, the gap between the edge of the profile and the head of the nail must be at least 10 times the diameter of the fastener.

Source pilomaterial-stroi.ru

Silicone transparent corners

Such products are ideal for framing corners covered with wallpaper. They are very soft to the touch. If they close the corners in the children's room, the children will be less injured. The silicone profile has only one drawback: its transparent texture is unable to close the finish defects from prying eyes. This must be taken into account when choosing and purchasing products of such a plan.

Silicone profile is an excellent tool to ensure the safety of children Source d.allegroimg.com

On our website you can find contacts of construction companies that. You can directly communicate with representatives by visiting the exhibition of houses "Low-Rise Country".

Polyurethane

With the advent of polymeric materials, the possibilities for decorating residential premises have expanded markedly. On sale there are corners with smooth surfaces, with a complex relief that skillfully imitates the texture of gypsum stucco. In contrast to the plastic profile, the thickness of the shelf is greater. This complicates the installation process, but the appearance of the finish benefits from this. The polyurethane corner creates effect of solidity. In addition, it can be additionally painted with paints used in decoration, but there is no plastic profile.

Source relative-oboi.ru

In the manufacture of products, pressing technology is used. It allows you to create decorative profiles of various shapes. They are not afraid of moisture, temperature changes, serve for a long time.

Source 1decor.ru

Manufacturers offer universal white polyurethane corners, they are best suited for painting. There are profiles, the texture of which skillfully imitates wood. Products look beautiful, in which the smooth part is painted, and the upper ornament is decorated in gold. Such corners are ideal for classic interiors. They are attached to a special adhesive composition. For these purposes, you can also use liquid nails.

Source cap40.ru

Colored plastic

Such products have a smooth, even surface. They are made from polyvinyl chloride. Manufacturers produce collections in which products of thirty shades are presented. There are profiles among them that imitate the surface of wood, metal. Their scope is not limited by physical parameters, so the plastic profile is used quite widely. For the design of arches, flexible corners and arched products are produced.

Source kitchenremont.ru

A plastic profile is mounted on a plastered wall simply:

1. Glue is applied to the surface of the inner part of the profile with a dotted line at a distance of 30 cm.
2. The profile is then applied to the surface of the arch or straight end.
3. From above, the corner is fixed with molar tape.

Source www.tehkomfort.kz

In order to glue plastic to the surface of the wallpaper, it is important to make sure that the canvas “sits” firmly on the surface of the walls, that the glue under them has dried well and provides a reliable adhesion. Otherwise, under the weight of the ceiling, the wallpaper will fall off and hang. It is better to glue the corners a few days after wallpapering.

Video description

The video shows how to glue plastic decorative corners:

MDF

This material is also used for the manufacture of a decorative profile. In the process of its creation, two strips of the same size are fastened together with an adhesive film. It is applied from the front. Its color and pattern matches the color and pattern of MDF. Such products can be used both for decorating external corners, and for framing internal ones. The degree of the angle is not important.

Source repair-book.com

Note! Corners made of MDF are undesirable to use in the interiors of rooms with high humidity.

In this way, the corners of the walls sheathed with MDF panels are formed. Source www.meister.com

Choosing a Corner Design

In order for the decoration of the room to be in harmony with its content, it is important to take into account various factors when choosing a profile. It is important to pay attention:

1. on surface materials. If the walls are lined with clapboard, the ends covered with a white plastic profile will look ridiculous.
2. On the color of the finish. A red profile will spoil the overall impression if the room is made in pastel colors.
3. For styling. The metal profile is not well suited for interiors in a classic style, but it is able to emphasize the high-tech concept.
4. On the function of the room. A plastic profile is ideal for kitchens and baths; silicone corners are better for children's rooms. Wooden with chamfers will be appropriate for the design of cabinets.

Design options may vary. The easiest way is to match the color of the profile to the color of the walls. He will merge with him, and will not attract attention to himself. Such a decision is justified when the surface often catches the eye, it can be, for example, the corner between the hallway and the room.

Source www.grandecor.ru

If the choice falls on wooden corners, designers are advised to match the colors and textures of doors or floor finishes. Then it will look organic. If you want to save money, you can buy wood-like plastic corners.

Source imageserver.ibud.ua

When creating laconic interiors with a minimalist style, the choice of metal corners becomes justified. They look good in hi-tech, in a loft. The width of the shelf must be chosen such that it completely covers the end of the corner. You need to pay attention to this if the walls are covered with panels, drywall, if additional insulation and soundproofing are performed. For such structures, the edges always turn out to be uneven, the decorative corner covers all defects well.

Source krovati-i-divany.ru

Typically, the angle between the slope and the wall is greater than 90 degrees. In order for the selected profile to be able to lie well on it, it must be slightly bent. You can do this with both metal and plastic corners. To do this, experts advise putting the product on a flat surface with one edge, and then press lightly from above with your hands and push it along the entire length of the corner with a brush. In the cold season, such a procedure should be done after the product has been in the room for a day and the room temperature has been taken.

Video description

The video tells how a metal corner profile is installed on a ceramic tile:

Briefly about the main

Decorative corners help to solve many problems. They improve the aesthetics of the finish, protect the ends of the walls and their inner corners from mechanical damage. The products are inexpensive, it is very easy to mount them, so if necessary, you can experiment and try to improve the design of an already finished interior.

The most characteristic part of the house, in terms of architectural decoration, is the corner of the house. In this part of the building, you can see all, or almost all, elements of the facade stucco.

Roof overhang decor

The overhang of the roof is decorated with a large or small, complex or simple, single or composite subroofing cornice. A little lower there may be an additional dividing strip on the facade, which allows for color zoning of the facade of the house. The corner of the house itself is decorated with a variety of options in order to visually reduce or increase the height of the structure. Rusts, pilasters, combined options are the main types of facade decor for the corner of the house. A separate and most basic part of the decoration of the exterior walls of the house is the facade decoration of the window.

window decor

The main task in the decoration of the window opening is also the alignment of the general proportions of the building due to the decor. More details and details about window slope design you can see on a separate page of our site. Also a very important part of the facade decor is the interfloor dividing strip. With the help of this decor element, the issue of separating different materials for decorating the walls of the facade of the house is easily solved.

home wall decor

Also, with the help of interfloor molding, we visually reduce the not always proportional height of the house. And the final one in the set of facade decoration of the walls of a private house is. This element is primarily a logical separator between the basement part of the structure and the main wall. Also, the basement profile can perform technical functions - smoothing the difference between the protrusions of the wall and the basement, drip, etc.

Below are a few examples of facade decoration on the corner of the house. You can see more ready-made design options for the facade of the whole house HERE.

1. House Facade Decor Example

In this example of the design of the facade of a country house, the under-roof cornice consists of two separate elements forming a massive filling.

Making the corner of the house

The corners of the house are decorated with beveled rusticated stones. Rusts on the corner do not join with each other, but are mounted each on its own side.

Window decor, slope

The windows of the second floor are framed by a molding 12 cm wide along the wall. The top of the window is supplemented with a profile with an angle cut, as well as a keystone. On the windows of the first floor, in addition to the molding, a decorative window sill profile was used.

decorative division

In this case, a double interstorey division of the facade is applied. One strip goes along the line of the second floor window sills, and the other along the floor slab of the first and second floors. This technique helps to significantly underestimate the visual height of the building. Decorative frames from a thin facade profile are used between the dividing strips.

Basement decoration

Wall finishing materials

2. House Facade Decor Example

On this fragment of the architectural decoration of the facade of a private house, the under-roof space is also filled with a combination of two separate stucco elements. The height of the composition is greater than its departure along the roof, which gives a strong effect that underestimates the overall height of the house.

Facade stucco molding on windows

The second floor windows are framed by two separate moldings. Along the edge of the slope there is a flat profile, around it there is a symmetrical convex element. Brackets are cut into the outer molding of the window, which support the massive top of the window. The profile of the top of the window is made with a bevel, which allows not to cover it with additional metal. The windows on the first floor are complemented by a window sill profile and a curly top with an angle trim.

Making the corner of the house

The corners of the house are decorated with rustication of various sizes with chamfers on four sides. Rusts are located at a short distance from the corner.

Interfloor separation

In this example, one strip goes along the line of the window sills of the second floor, and the other along the floor slab of the first and second floors. This technique helps to significantly underestimate the visual height of the building.

Finishing the basement of the house

The plinth element is located with a thin part upwards to smooth out the difference in the thicknesses of the plinth and the main wall.

Wall finishing materials

The main wall decoration is bark beetle or decorative plaster. The finishing coating of the walls is applied after the installation of decorative stucco. This helps to additionally isolate the joint of gluing decor elements to the wall. The basement is decorated with marble or granite.

3. House Facade Decor Example

In this set of facade decor of a private house, the roof overhang is also decorated with a combination of two separate stucco elements. The height and reach of the set are almost the same, which gives a complete and deep filling of this part of the facade of the house.

window framing

The windows of the second and first floors are decorated with a simple set of moldings and window sills with keystones.

Finishing the corners of the house with foam

The corners of the house are decorated with rustication of different sizes of a simple rectangular shape without a chamfer. This version of rustication is usually mounted from molded products.

Interfloor separation is made using two types of small size profiles located at a distance from each other. The gap between them is painted in the color of the decor, thanks to which we get a wide separation on the facade.

plinth trim

The plinth element is located with a thin part upwards to smooth out the difference in the thicknesses of the plinth and the main wall.

Wall finishing materials

The main wall decoration is bark beetle or decorative plaster. The finishing coating of the walls is applied after the installation of decorative stucco. This helps to additionally isolate the joint of gluing decor elements to the wall. The basement is decorated with marble or granite.

4. House Facade Decor Example

In this set of facade decor of a private house, the roof overhang is also decorated with a combination of two separate stucco elements. The section of the elements has a greater number of bends and steps compared to the previous version.

Decorative window trim outside

The windows of the second and first floors are decorated with a large molding around the perimeter. The cross section of the molding has a pronounced, convex, rounded shape. The top of the window is mounted at a distance from the molding and is supported by decorative brackets.

Finishing the corners of the facade of the house

The corners of the house are decorated with pilasters of relatively small width along the facade. Each element is located a short distance from the corner of the house.

Dividing strip

In the interfloor division, two separate elements are used between which there is a strip of architectural ornament. The upper dividing strip runs along the bottom line of the second floor windows. The lower strip runs along the interfloor slab.

Finishing the foundation of the house

The compositional design of the basement part of the house can also include, in this case, the strip running along the bottom line of the first floor windows. This option looks good in the presence of the so-called French windows - when the bottom of the windows is not high from the floor. The plinth element is located with a thin part upwards to smooth out the difference in the thicknesses of the plinth and the main wall.

Wall finishing materials

The main wall decoration is bark beetle or decorative plaster. The finishing coating of the walls is applied after the installation of decorative stucco. This helps to additionally isolate the joint of gluing decor elements to the wall. The basement is decorated with marble or granite.

5. House Facade Decor Example

This set of architectural stucco elements can be described as more complex in terms of geometry, complete set with decorative elements. Techniques were used to bypass additional thicknesses to create more relief and volume.

Window decoration outside the house

The windows of the second floor are framed with a wide relief molding 18 cm wide. From the window sill profile, additional reliefs imitating brackets are formed under the moldings by trimming at 45 degrees. The top of the window also has a complex relief due to undercuts at an angle. The keystone is embedded in the profile part of the top of the window.

Exterior decoration of the corners of the house

Dividing strip

Finishing the basement of the house

The plinth element is located with a thin part upwards to smooth out the difference in the thicknesses of the plinth and the main wall.

Wall finishing materials

The main wall decoration is bark beetle or decorative plaster. The finishing coating of the walls is applied after the installation of decorative stucco. This helps to additionally isolate the joint of gluing decor elements to the wall. The first floor is completed with rustication. This type of finish is performed by facades when insulating walls. Grooves are made in the insulation, which are then reinforced with the help of corners together with the main wall. The basement is decorated with marble or granite.

6. House Facade Decor Example

In this case, the main distinguishing feature of this composition is the massive, voluminous framing of the windows. The subroofing cornice is made of two separate elements. mounted at a distance from each other. Gap between top. the main cornice and a smaller strip on the wall are painted in the color of the decor, which visually gives a single composition.

Window design outside

The windows of the first and second floors are trimmed with small molding around the perimeter. Moreover, a figured frame was created from it into which the brackets are inscribed. On the first floor, a straight top window from a large profile has been added. In addition to it, there is an arched element on the second floor.

Decor of the corners of the house with polystyrene foam

The corners of the house are decorated with simple rectangular rustication of the same size. Such a performance is usually carried out by the performers of facade work on site or from a molded product.

Dividing strip

A voluminous, protruding dividing strip was launched between the floors. Its dimensions and volume create an additional relief on the facade of the house.

Finishing the basement of the house

The plinth element is located with a thin part upwards to smooth out the difference in the thicknesses of the plinth and the main wall.

Wall finishing materials

The main wall decoration is bark beetle or decorative plaster. The finishing coating of the walls is applied after the installation of decorative stucco. This helps to additionally isolate the joint of gluing decor elements to the wall. The basement is decorated with marble or granite.

related posts:

• Facade Design ~ 13+ Finished Appearance Solutions…

Repairing an apartment or a house is only half the battle. It is also important to maintain its condition for a long period. Difficulties can arise with this, since small children or pets are able to ruin wallpaper, flooring, doors and other finishing materials in a short period of time. The outer corners of the walls, which are located on the "passage", for example, in the corridor or in front of the entrance to the room, may suffer the most. Is it possible to get rid of such an influence of time on the walls of the house and how can additional finishing of the corners in the apartment help in this?

Such material for finishing an apartment as corners has several purposes:

• visual alignment of the angle;
• protection from damage that is inevitable in an apartment or house, especially where pets live;
• pollution protection;
• decorating and decorating walls.

In addition, such decorative trimming of the corners can be successfully used to improve the appearance of doorways, window plumes and panel joints. Their use can only be limited by the imagination of the owners of the apartment. Thanks to a large selection of decorative corners, you can easily choose the most optimal option for any room.

Advantages of plastic decorative corners

Options for mounting finishing materials on wall corners

The type of corners will depend on the option of their installation. Plastic products can be fixed with the help of additional means (specialized glue, "hatless" carnations) or with the help of an adhesive layer that has already been applied to the inner surface of the corner. A clear advantage of the second option is the flexibility of the product and the possibility of breaking it at any angle. But not all the material with which the corners of the walls can be finished, it is possible, even during the production process, to apply an adhesive composition. For example, artificial stone belongs to such a finishing material. It consists of tiles of different sizes, which are made of concrete or plaster. Decorative stone can decorate any external corner in the apartment. The design of modern hallways or living rooms in this way is very popular (photos can be viewed on Internet portals).

Regardless of the chosen type of fastening of this decorative element, the finishing of external corners should be carried out only after the repair of the walls is completed. That is, all the necessary work has been completed: wallpaper has been glued, paint has been applied, decorative plaster, etc.

Installation of plastic decorative corners

Before proceeding with the installation, make sure that the wallpaper, paint or plaster has dried sufficiently so as not to damage their surface with plastic. You should also purchase an adhesive that will be used to attach the decorative corner. If a self-adhesive model is used, then there is no need to purchase such a tool. Please note that the adhesive layer on such corners is covered with protective paper, which must be removed before gluing to the wall surface.

As mentioned earlier, the following can also be used as "fixing" means:

• carnations without caps;
• liquid Nails;
• sealant.

When buying liquid nails, you should pay attention to the fact that the product is not high strength (the degree of strength is indicated on the package, as well as the list of materials with which this product can interact). Since when used with plastic products there is a risk of corrosion. Liquid nails with high strength are designed for heavy (metal) parts.

Although decorative plastic corners can visually transform uneven wall corners, you need to determine what level of “curvature”. To do this, you can use a regular ruler or a flat board: it should be applied to the edges of the corners between which the unevenness is located and analyze the degree of "distortion". If the transition from a flat wall to a curved one is not very noticeable, then you can safely mount the product. Otherwise, if you install a decorative corner on a strongly curved wall, then after a while a gap will form due to a significant difference in the size of the corner.

Installation of decorative corners does not require special knowledge, even a beginner who does not have sufficient knowledge can do it. Since this product should be fixed only after the final processing of the walls, the process is greatly facilitated.

Installation instructions

For the installation of self-adhesive corners, the same sequence of actions is applicable, with the exception of point No. 1 (applying glue to the surface of the corner).

Instead of plastic decorative corners, MDF products covered with plastic film can be used, and, as noted earlier, decoration with decorative stone is also possible. All of these materials can also protect wall corners from chafing and damage. Photos of the corners in the design of which these materials were used can be found on Internet resources.

Decorative corners made of MDF, thanks to a wide selection of colors, can become a great decoration for any room. You can also attach them to the walls using special adhesives, sealants or liquid nails (on the packaging of the selected product, MDF should be in the list of materials with which the adhesive interacts). Like any other decorative corners, such products can be used not only to decorate walls, window and door spans, but also serve as decoration and protection for other interior items.