Floor clothes hanger (47 photos): everything for your favorite things. DIY clothes hanger: types, designs, drawings, manufacturing DIY hat hanger

There is a large number floor hangers for clothes. At home, this is a very relevant and practical furniture that fits perfectly into any interior. Such hangers can be easily moved around the apartment and room. Things in this case are much less wrinkled than in the closet. It needs a dust cover. Such a design can be made with your own hands. Let us consider in more detail the manufacturing process of various models, photos of which will also be presented in the article.

Advantages

Stylishly fits into any interior and does not take up much space.

The good thing about this is that hanging clothes does not come into contact with the wall, and this allows you to protect the wallpaper from damage. At the same time, the device can be folded, removed or rearranged at any time, which is very important in small apartments.

If it is made by hand, then the following advantages appear:

• the cost is significantly reduced;
• is in an exclusive piece of furniture;
• no need to drill holes in the wall to hang it.

Necessary materials

Consumables can be absolutely anything: from oak to metal.

How to make a stand with your own hands? First you need to decide on the material. Plywood is suitable for work, these are the most practical materials that you can easily work with. During its operation in the house, it is not exposed to moisture, which significantly increases its service life.

Working at home with plastic or metal is quite difficult, so it is better to refuse them. It is also necessary to take into account such a moment that a large load is placed on it, therefore, materials of appropriate strength are also needed, which do not allow breaking.

When purchasing plywood or wood, you need to pay attention to their quality, as the appearance of the product will depend on this. Usually, an oak structure is covered only with varnish or stain.

From plywood in the form of a tree

The process of creating a product, with its subsequent use for storing clothes.

It is not difficult to make such a product yourself and it does not take much materials and tools. This product requires two sheets of plywood measuring 70x170 cm and 18 mm thick. For work you will need:

• jigsaw;
• glue;
• sandpaper.

The manufacturing process itself does not take much time. First, on one sheet of plywood, draw the outline of the future structure. The main thing is to have a width of about 60 cm. This is necessary for stability, because if they are narrow, then it will fall if you hang heavy winter clothes on it.

In order not to draw a picture on the second sheet of plywood, it is necessary to fasten two sheets of plywood with clamps or self-tapping screws, making sure that the sheets do not move. To turn the blanks into a finished product, two cuts are made. On one blank, a slot is made from the top to the middle, and on the second from the bottom. The width of these slots should correspond to the thickness of the plywood.

On the inside, both slots should glue carefully, and then one blank is put on another. The result is a rather original thing, a photo of which can be found on the Internet. It remains only to sand and paint it. You can decorate it in different ways or simply varnish, stain or paint.

From a tree trunk

A very original solution is interior items that look like a branch or trunk with knots. Such gizmos always harmoniously fit into any room.

Good design solution- This is a stand made of natural natural material, namely from the trunk. It is very easy to do and there is no need to purchase special tools.

How to make it yourself? To do this, you first need to find a quality blank from a dry log, on which there will be no rot. The breed does not matter, but it is still better not to use conifers containing a large amount of resin. Glue is able to stand out even from a dry trunk. It is advisable to use hardwoods that have good branching so there is more room for clothing.

His you need to clear the bark, cut the lower branches to a height of one meter, and shorten the upper ones, leaving knots on which you can later hang clothes. After that, the rack is completely sanded and cleaned of bumps and dirt. If the wood is damaged by a bark beetle, then this does not hurt, because it creates an amazingly beautiful pattern that fits perfectly into the design.

Then you need to make a stand, because the tree trunk cannot stand on its own. The main thing is that the stand is massive, this makes the structure more stable. The stand itself can be of any shape: round, square, triangular.

Photo gallery

The base is attached to the stand in various ways. For example, if its lower part is rather thick, then the board can be screwed to it using self-tapping screws, the caps of which will be located below, so they will not be visible. If the bottom of the trunk is thin, then a hole is made in the stand, no larger than the diameter of the trunk itself, after which the base is fixed on the stand with glue, since this method is the most reliable.

After it is made, it must varnish to keep the natural color. But if the light system does not fit the design, then dark paint can be used.

In the form of a ladder, do it yourself

Old and unnecessary stairs can also be used and given a second life.

Highly looks original- in the form of a ladder. To make it yourself, you will need two bars 170 - 180 cm long and 5x5 cm thick. For the crossbars, you will need three smaller bars, the length of which will be equal to the width of the product. All bars must be sanded or processed with a planer.

To make the design look neat and beautiful, all the details are interconnected with spikes. After that, the product is varnished and stained. A comfortable and convenient do-it-yourself clothes rack is ready. It can be installed both in the bedroom and in the summer house.

Rustic

This design will fit well into the corridor or hallway, and you can put shoes under it. This model is not easy to make yourself. First, holes of large diameter are made in the crossed round racks. It is very difficult to drill holes in round parts with a household tool. To get around such an unpleasant nuance, you need to take square racks and use a drill to make holes in them of the desired diameter. It is best to take a metal crossbar, as it will sag. This model can be disassembled. To do this, the crossbar is removed from the holes, and the parts that make up the hanger are compactly folded.

on wheels

The wheels are very convenient and make the thing very mobile.

This design has regular hangers on top, which is very convenient for placing blouses, shirts and a jacket. Pants are more convenient to hang on the crossbars. Thanks to the wheels, it is easy to move it to another place.

To make it yourself, you will need special fasteners. Vertical posts are attached to the base with metal screws. The only difficulty is drilling holes for the screws in the uprights. The rest of the assembly is pretty simple. The disadvantage of this design is the need for disassembly during transportation. To do this, unscrew the long bolts from the vertical racks.

Thus, there are many ways to make such a clothes hanger with your own hands, the photo of which was presented in the article. This is a very simple element of the interior, for the manufacture of which you will need available material at hand. Usually, special tools are not required for work, and the result is a unique and exclusive thing.

It is the entrance hall that the guests see first. This is the face of the apartment, which characterizes the owner. For the best design of this site, you should remember about the space. A large closet in this case is not appropriate. Therefore, the actual question is how to make a hanger with your own hands.

About all the nuances of this process a little lower.

Characteristic

Placement of wall-mounted clothes hangers is possible in different places, and the hallway is no exception. It could be the kitchen or the bathroom. It is important to make this product an unusual addition to the interior. With the right approach, an ordinary hanger will become a bright accent made in the style direction you need.

The product must meet certain requirements. Stylish looks simple, lightweight, but durable design, with affordable and compact materials.

Mounting differs in the method of installation work. As you can see in the photo, hangers are distinguished by wall, ceiling, and mobile products.

Using wall structures, preference in manufacturing is given to corner structures. Designers advise to combine several types. For example, it can be a wall structure in combination with a support, for example, on the floor.

Important! Floor structures in the bathroom and kitchen are not used, as this is inappropriate. After all, hangers take up a lot of space, interfere with the rational placement of other necessary items.

Products differ in the method of hanging. Known designs with hooks, with a bar designed for hangers. The first option will be the way out if you need to rationally place things, saving free space.

The advantage of the second option is quality. After all, you can hang things on a coat hanger without fear that it will wrinkle, lose its attractiveness.

Material selection

The most common option is to make wooden hangers. Forged designs are popular, but they do not always fit into the style composition of your interior.

Often a hanger is made of metal. Most often, hooks are fixed with glue, screws, magnets. You can use suction cups for this purpose.

It is necessary to decide for what purposes the product will be used. If you will hang outerwear, then the best option is to use self-tapping screws. After all, they will help to withstand a lot of weight.

The rest of the methods are used in the bathroom, or the kitchen. They will easily withstand towels, potholders.

The working process

It is worth considering what ideas there are on how to make a hanger. Let's consider the simplest option, which can be interpreted, combined, added in different ways.

Material should be prepared. Further, for the workflow, a jigsaw is required. For fasteners, you will need additional material, a puncher. You also need a level, corner, tape measure. For drawings, prepare a pencil, or a marker.

The simplest manufacturing option is a plank with hooks. You need to take a wooden board.

Note! For a quality product, you should carefully select a board. Its surface should be perfectly flat, without cracks, bumps. The material must be well dried. Only after following all these rules, you can start working.

You can notice a wooden plank with a sheet of chipboard, or MDF. It is important to consider the length ratio that will suit your individual needs.

There should be such a distance between the holes that the indentation is approximately 5 cm. For an even arrangement of the holes, it is necessary to use a building level. Dowels are inserted into their surface. Self-tapping screws are screwed into the base. Hooks must be attached to the bar. Depending on the fastening material, the strength of the entire structure is determined.

Instead of standard hooks, you can use several interesting variations of them. Often, old wrenches are used for these purposes. First of all, they need to be prepared for work, that is, cleaned, polished. Then they are bent, then screwed to the bar.

Steel forks are often used. They are also ideal for this purpose. Avoid choosing aluminum material as it is brittle in structure. With the right material, the teeth can be given a rather interesting shape.

Another option is wooden knots. Moreover, it is not necessary to place them exactly. Often a stave is drawn and the hooks are placed according to the position of the notes.

findings

A homemade product fits perfectly into the style direction of the room. Hangers are no exception. Such designs are quite easy to make on your own, improve the standard options, supplement them with your wishes and imagination.

Designers advise, they are not afraid to experiment, combine different methods, create something of their own. Such a thing will undoubtedly decorate your hallway, characterize you as a creative and talented person.

DIY hanger photo

Do-it-yourself clothes hanger is a fruitful idea. Theater begins with a hanger; house too. In the sense of spirit, atmosphere, "energy". The reason is simple: the first thing a guest looks for is where to hang outerwear. And if the hanger is clearly home-made, but comfortable, stable and durable, a positive reputation for the owner is provided.

The second argument for making a hanger with your own hands is prosaic: purchase prices are clearly disproportionate to production costs. A homemade clothes hanger will save you quite a visible amount in the budget. It is not difficult to make it, it will take a little material, and waste from repairs will also go into business. The tool in most cases can be dispensed with by hand.

These factors are especially felt if a floor hanger fits in the hallway. In addition, it can also serve as a dryer if its design is frame, see below, because. On such hangers, it is convenient to hang clothes on hangers, and the hanger itself moves away from the wall. If the house managed to shield the dressing room, then the floor hanger is the best option. The cost of floor hangers is significantly higher than wall hangers, but there is nothing in the design that would not allow you to make a floor hanger yourself.

On the floor or on the wall?

It has already been said enough to make a choice, as long as there is enough floor space. However, let's finally compare how attractive a hanger is in a floor-type hallway:

• Clothes hung on hangers dry faster, do not stretch; the collar and lining are not torn.
• On a hanger approx. 1.5 m fits a seasonal set of clothes for the whole family, which will save on the closet and the area under it.
• A shoe rack is naturally attached to the floor hanger, which simplifies the work of equipping the hallway and saves its area.
• With correctly calculated dimensions of the hanger, neither the wall from the clothes nor the clothes against the wall are damaged.
• The mobility of the hanger does not interfere with the rearrangement of furniture; after moving the hanger, it is not necessary to seal the mounting holes in the wall.

However, floor hangers are different, and not all of them are most suitable for living quarters. For example, for orders (from the old Russian “order” - office, office, office) floor lamp hangers, pos. 1-4 in the figure, it is inconvenient to hang clothes on hangers. Due to the small area of ​​​​support, they are rolled, especially loaded with wet winter clothes. To emphasize the functional inferiority of the product, such hangers are called hangers, and they often go on sale under this name.

Types of floor hangers

The best option is the same theatrical wardrobe frame hanger, pos. 5. In the version for residential premises, it is supplemented with shelves for hats, shoes and gloves / scarves; perhaps an additional tie rod, pos. 6. Disadvantage - the "legs" of the hanger get underfoot. In an attempt to get rid of it, hangers were invented - frames on a stand, pos. 7, but generally speaking, they fell even more than the orderly ones hung up. Another option is a hanger-frame without legs, leaning against the wall; we will remember this one. There are also folding frame hangers, but in everyday life they have almost no advantages.

If in the hallway with a place is generally tight, then a wall hanger is still more suitable. Simple wall hanger-sconce, pos. 1 in Fig., is as compact as possible, but not at all more convenient than the order, except that it does not fall from the next jacket to one side. Hanger-shelf, pos. 2 won't fall off if it's attached properly, and neither will hats/caps, but the wall and clothes rub against each other.

Types of wall hangers

Wall hanger panel, pos. 3, saves the wall, but not the clothes. Most of all, leather things wear out on such hangers. Tanners jokingly advise: how, they say, to distinguish a sheepskin coat from full grain leather from it from reverse? The first, with everyday use of a hanger-panel, loses its appearance in 2 winters, and the second - in half a winter. Given the cost of genuine leather products, this is no good. Therefore, hangers-panels on the wall for expensive things are often supplied with soft upholstery, pos. 4. As for wall hangers with an openwork shield, pos. 5, then in this case its meaning is only decorative: it does not protect either things or walls.

Floor hangers with chest and bench

There are also floor hangers-panels with a stand, for example. in the form of a cabinet, chest or chest, pos. 1 in fig. on right. This is not the best option: someone will once put something on the lid, and with the clothes removed from the hanger it will be whisked to the floor. Much more practical are floor hangers-panels with a bench, pos. 2. The flower under the seat is a matter of taste of the owners, if only he survives there, but the shoe box or chest for accessories to care for her in the banquette drawer is the place.

Clothes and keys

Regarding hangers-panels, the amateur master has an additional opportunity, namely: to provide such a sidewall on the edge farthest from the front door. Perhaps not reaching the bottom, with a bevel or notch. The factory ones do not do this: the hanger should be designed for clothes sticking out from the side. One sidewall almost does not interfere with this, but it is not known how the hanger will stand with the buyer, and it is unprofitable to make right and left hangers.

What gives such an addition? Place for the housekeeper, invisible from the threshold. In the same place, on the side, there may be a dressing table or cabinet, but the main thing is that the master's keys will not catch the eye of a casual visitor, and they are in sight, according to criminologists, a serious factor in spontaneous illegal actions, without which, i.e. temptation, the visit of a not entirely trustworthy subject would have done well both for the owners and for him. You can, of course, make a key holder luxuriously designed and with a secret lock, but this is a lot of work and material costs. And so - a simple plank with hooks will do. Or just hooks screwed to the sidewall outside of the stowage section.

We will assume that a suitable design has already been selected, and let's take a look at how to make a hanger. Preferably wooden: the material is noble, natural, easy to process. Let's not forget other versions; more convenient in some cases. Let's start with floor hangers as the most functional.

floor standing

Lovers of crafting from the heart, having a milling tool for wood, can immediately take up the floor frame hanger with legs. Made of small-layer hardwood (oak, beech, hornbeam, walnut, birch), it looks chic, and it will take only 360 mm of the floor in width.

A suit hanger works well as a prototype, you just need to make it higher and move the trouser bar up so that you can hang coat hangers on it. Instead of a tie rod and handles, a shelf can be installed, and a shoe shelf is mounted below. Drawings of such a hanger are shown in Fig.:

Drawings of a wooden floor hanger

With the indicated other dimensions, the structural and overall width (dimensions 430 and 460 respectively) without compromising strength and stability can be increased by 1-1.4 m, i.e. the hanger will be already a family width up to more than 1.8 m.

About hooks and trempels

Bags, umbrellas, scarves are also left on the hanger, and a bachelor can also have a skirt with lingerie there. Sometimes life is life. It is also more convenient to hang clothes on hooks for a short time. Therefore, in frame hangers, sometimes runner hooks are put on the main bar (the former trouser bar in Fig; height 1360). They or hangers, depending on the need, are shifted to the side in a crowd. But the hook-runners under the fingers turn out at the most inopportune moment. In a hanger of this design and similar ones, the problem is solved simply: the main bar is for hangers, and fixed hooks are attached to the top board.

Pipes and profiles

Original hangers are obtained from round or shaped metal or plastic pipes, see fig. However, despite all the design tricks, their organic vices do not go anywhere. The same as the orderly hung. But high labor intensity is added: in order to hide the connecting nodes, you have to strain both your arms and your head.

Pipe hangers

It is better to make a square base of a floor lamp hanger from pipes. With the same withdrawn floor area, the distance between the support points increases by 1.4 times. If the base is still heavier, then the hanger up to 1.7 m high turns into a full-fledged hanger. 60 mm sewer pipes are most suitable.

A short master class in pictures on making the base of a floor hanger from pipes is shown on the next. rice. Pipe sections - 150-300 mm each, depending on how much floor can be given to the hanger. In addition to them, you will need 3 straight tees, 4 right angles and 4 plugs. Connections - on glue for propylene or PVC, depending on the pipe material. Weighting - sand or small gravel.

Making the base of the hanger from pipes

One of the comments on the original design begins with a question like this: "Why couldn't you just solder?". Judging by the fact that later in the same comment, 90 angles with a clear claim to professionalism are called bends (plumbing bends are oblique tees), another 2-3 and the same number of exclamation points suggest themselves to the question mark.

Nevertheless, the author of the product, albeit not knowing plumbing terminology, solved the problem in a completely engineering way. The hanger does not need tight joints, and a tube of glue will cost much cheaper than renting a soldering iron for propylene. Which, moreover, you need to learn how to use, spoiling a fraction of the material. For greater reliability, you can reinforce the connections with phosphated (black) self-tapping screws: on black, their heads are not visible, and the strength of the hanger will not decrease.

Note: the pommel in the original design is also made of pipes, but, frankly, its design is not the same ... It would be better to drill inclined holes in the rack and insert some strong pins into them using the same glue; wooden, metal.

simple frame

Scheme of a simple floor-wall pipe hanger

A frame hanger made of pipes can be without legs, just leaning against the wall with an inclination. However, its slope must be negative. There must be at least 350 mm between the wall and the clothes on the hangers. If the slope of the frame is positive (the upper crossbar is adjacent to the wall), then the lower one will "leave" from the plinth by 500-600 mm. In a small hallway, this is a serious inconvenience. In addition, they will either cling to the lower crossbar with their feet and it will beat the floor, or it will have to be fixed to the floor, and this is really bad: any violation of the flooring is fraught with complex and expensive emergency repairs. Have you seen furniture for sale that needs to be screwed to the floor? Is that a special purpose, for example. rack. And then, they also try to get by with fastenings to the walls and, in extreme cases, to the ceiling.

A diagram of a frame hanger with a negative slope of pipes is shown in fig. The materials are the same: 60 mm straight sewer pipes, 90 angles and straight tees. Withdrawn usable floor area - zero. At the bottom there can be a shoe rack or a banquette. For fastening to the wall, in order not to drill a lot and do without expensive collet anchors, it is better to take a couple more tees: with their help, the holding beams - extensions are attached to the wall with a pair of self-tapping screws in dowels each.

wall

Simple hangers-panels do not require special analysis. How to make a wooden wall hanger, see for example. video.

Here we recall, firstly, the sconce hanger. Foldable, it can be very useful if a large company has gathered or the kids have returned from the yard at least squeeze it.

An example of such a structure is shown on the right in Fig. However, its creators were clearly guided by the principle: "Consumption is the basis of cash flow." The outer (folded) side of the flap bar is inactive and a locking mechanism is needed. And a separate hanger for every day.

Compact folding wall hanger

Meanwhile, folding wall hangers have been known since ancient Egypt. In the local climate, outerwear was worn occasionally, in bad weather, but after wearing it, it was necessary to dry it. There was no point in keeping a separate hanger for this in the regions where it rains and cold once a year, not every year, so they came up with the one on the right in Fig.

When folded, the compact wall hanger of the Egyptians was fixed with a cypress stick. Now, of course, you can put a ball retainer or just a hook. The main thing is that the hook hooks should be in 3/4 of the circle, then nothing will fall off them even with the bar folded back. And without need, the whole hanger looks like just a stick on the wall; you can hang bags, umbrellas, keys on hooks.

More about hooks

The original wooden hanger can be made without metal at all, not counting the fasteners. Do not rush to throw away the New Year's pine or Christmas tree (only the blanks will need to be turned upside down):

Video: original do-it-yourself wooden hanger

Best of all, such a hanger will look in the country, in a timber or frame house. Depending on the interior design - and in a city apartment. She will go to the bathhouse perfectly: the touch of steamed skin on metal is unpleasant, and to some extent even traumatic.

Hangers in the nursery

Probably, all children scatter wearable things. There is no need to especially scold them for this: without knowing chaos within reasonable limits, you will not accustom yourself to order. Who is against - answer Friday's question to Robinson Crusoe: "Why doesn't God kill the devil?"

However, teaching children to handle things properly is necessary. Only a children's hanger, so as not to cause obvious psychological rejection, should look somewhat disordered. It is also highly desirable that the child associates it with a favorite game or hobby. Examples of wall hangers in the nursery of the "game / hobby" type are given in pos. 1 and 2 fig.

Baby hangers

A universal method of this kind is a tree hanger, pos. 3. In the contour of a tree, as in any fractal structure, order and chaos interact and complement each other, creating a harmonious whole. Do not forget to just make the tree stronger, for example. from plywood from 12 mm, and, as it should, with a step of no more than 250-300 mm, attach to the wall with self-tapping screws from 6 mm in propylene dowels. A tree, after all, to climb on it.

Floor hangers in the nursery are undesirable for the same reason: well, they will climb anyway and crash. Therefore, if you already want a floor hanger in the nursery, you need to make one that you can’t fit on, which can be seen in pos. 4 and 5.

About cutting plywood

In any case, parents face problems that small ones don’t care about yet: material consumption and labor intensity. It is no longer easy to draw a complex contour along a grid on a solid sheet of plywood, then it must be accurately cut out, which is even more difficult. And in the end it turns out that 60% or 80% of the material went to waste, no longer suitable for anything. It is necessary, on the contrary, to make a children's tree hanger from waste. Or cut a denser whole sheet.

Assembling parts of a plywood hanger-tree

The method for this has long been known: element-by-element cutting and assembly. If the tree is plywood, for the full strength of the finished product, each part is recruited from 2 layers, leaving resp. folds and grooves, see fig. Fragments of blanks are assembled on PVA glue, wood glue or Express (liquid nails). If the assembly is on PVA, the fragments must be additionally fastened with small nails with a snake in increments of 100-150 mm with an indent from the edges of 30-40 mm.

They assemble a tree hanger on the same adhesives, but now each connection must be fastened with self-tapping wood screws with an envelope. Then the gaps and fastener heads (they must be drowned during assembly) are rubbed with putty from sawdust of the same plywood on PVA. Such a tree, even without painting, only under varnish, will look solid.

Note: just in case, we recall that before assembly, all the wooden parts of any wooden hanger must be sanded with fine sandpaper and treated with a water-polymer emulsion or PVA diluted with water three to five times. After impregnation, before further work, a technological break is made until the part is completely dry (1-3 days, depending on its size).

And one last thing about hooks

In the illustrations above, you most likely noticed curved wooden hooks and other hanger details. It is quite possible to make them at home. In production, dense, small-layer, defect-free wood or waterproof birch plywood (BS grade) is bent heated with steaming or dry, but these methods are too complicated for homework. Only bamboo is more or less simply steamed: the workpiece is boiled for half an hour or an hour in rapidly boiling water, after which it is bent by hand. In case of bending according to the template, the workpiece must be fastened to it quickly, before it has cooled down, with a wide cotton braid or a strip of natural tarpaulin.

Wood rasp

At home, it is easier to cut blanks of the required configuration from a sheet of plywood (any) or MDF of the desired thickness, or, twice or four times as many in quantity, from thin sheet material, in order to then gain as much thickness as required. Cut with a finishing allowance of approx. 1 mm. The cut blanks are tightly pulled together in a package in a carpenter's vice or in a metalwork through gaskets made of thick plywood and processed with a rasp on wood to size, and then with a clean sandpaper. One rasp is enough, with flat and semicircular working surfaces, see fig.

The workpieces are assembled into parts in the manner described above. The end surfaces, if you need to hide the layered structure of plywood, are sealed with strips of self-adhesive film under the tree. After that, the part is varnished twice or thrice with water-based acrylic varnish; nitrolac can ruin the self-adhesive. It is not worth edging (edging) with a plastic furniture edge: you need to accurately select the groove for the edge anchor, which requires a milling machine, but on curved surfaces of large curvature and short length, the edge still does not hold well. And the details pasted over with self-adhesive, under varnish, from solid wood, even the master cabinetmaker will not immediately distinguish.

As you know, the theater begins with a hanger. The hallway also begins with coat racks. The hanger is an important interior element that can decorate and complement, as well as streamline the situation. It should look attractive and not take up much space. Today, the furniture industry produces a wide range of various designs of various designs, but many are interested in how to make a clothes hanger with their own hands. It is these products that transform the atmosphere, make the premises unusual, original and with a "zest".

Making your own hanger is pretty easy. This will require imagination, as well as the desire to make something extraordinary, something that cannot be bought in a store. A homemade hanger will undoubtedly decorate any room and attract the admiring glances of guests. For its manufacture, you can use any materials at hand - empty bottles, beads, wire and all sorts of little things that are likely to be found at home. Gifts of nature, for example, a bizarrely shaped branch, as well as the remains of building materials after repairs, are perfect for this purpose.

The design and shape of the future product depend on the wishes of the owner. You can look for inspiration on the Internet, see photos of the original hangers, or download a diagram of your favorite idea. In any case, you first need to decide on the type of hanger and the material for its manufacture.

What are hangers

There are two types of hangers that you can make yourself - wall and floor.

A wall hanger is the simplest solution. It usually consists of a horizontal bar, to which hooks are attached in one or several rows, an upper shelf for hats or a special cross beam for “hangers” can be provided to it. The shape of the horizontal crossbar-base is usually rectangular or with rounded corners, but if desired, it can be made absolutely any. For example, in the form of a heart or a tree leaf.

Usually the wall hanger in the hallway is made of wood. The fact is that wood is an excellent natural material that can be easily processed at home: cut the desired shape from the canvas and cover it with any paint.

The floor hanger is a structure consisting of a vertical support on the base. Hooks for clothes are attached to the top of the support. It is important that the hanger is not only decorative, but also practical. Particular attention should be paid to the base. It must be very stable so that the structure can withstand the weight of the clothes and not fall. There are many design options for such hangers, but they differ not only in shape and size, but also in the material of manufacture.

Floor hangers

First, you need to decide on the material. Floor hangers are:

• Metal.
• Forged.
• Wooden.
• Plastic.

Metal products are very strong and durable, have a lot of weight, so they are considered the most stable. Metal hangers with elements of artistic forging are real works of art that will bring elegance to any hallway. However, not everyone is able to make this kind of product at home, because the work will require a complex tool and metalworking skills.

The easiest option for making a metal floor hanger at home is to re-equip an old floor lamp. It has a support and a lampshade, on which thick wire hooks can be attached. By the way, you can weave original patterns from it and use them as hooks for clothes. The base can also be decorated with decorative elements.

A wooden hanger is a great budget option for a hallway. Wooden products do not go out of fashion. They fascinate with their natural beauty, they can be used for any style and direction in the interior.

To make a wooden hanger, you can use a sheet of plywood or board, but if you want to make something really unique, it is better to turn to the gifts of nature. So, a small dry tree can become the basis of a future hanger.

It should be cleaned of bark and knots, carefully treated with sandpaper and fixed to the base. In this case, it is better to provide support on three legs, it is considered the most stable. Then you need to decorate the top of the hanger. It can be made like a tree crown. As hooks, you can use a beautifully shaped branch, which must first be cleaned and sanded.

The final stage is the coating of the entire structure with varnish or paint. As a decoration, you can use balls or large beads, which are fixed with glue to the base of the hanger or on hooks.

A photo

Video

This video shows the process of making a wall hanger.

Here are some more ideas for inspiration.

A huge number of offers of floor clothes hangers suggests: what if you do it yourself? At home, a suit hanger, hangers for outerwear and children's clothes, which are covered with a dust cover, are relevant and practical furniture. Such furniture fits perfectly into the interior, it can be easily moved around the room and apartment.

Clothes on such a hanger wrinkle less than in the closet. It is sometimes called a dressing room, for the fact that it allows you to partially unload the furniture wardrobe, and the costumes will be in sight. It is also convenient to place children's things on such a design. Cover for a hanger, necessary as protection against dust.

The main difficulty in making with your own hands lies in the processing of surfaces and compliance with dimensions. The conjugation of parts should be maximum, which is not always possible to achieve manually. Therefore, in the manufacture of a floor clothes hanger, a combined method should be used: some of the parts and operations will have to be ordered by professionals.

Model selection

According to surveys and sales numbers, the most convenient model of a floor-mounted coat hanger for a suit covered with a cover is the hanger of the following design:

Dimensions can be changed as you wish. On the upper radius board on the back side, it is desirable to strengthen the hook for children's coat hangers. This will expand the range of applications for the hanger. Do not greatly reduce the thickness, as under load, deflections of parts are possible. Increasing the size within reasonable limits will make the hanger more stable.

You can choose any material: beech, ash, cedar, birch or pine. The latter is the most accessible. It is easier to process and finish. When choosing a material, its moisture content is especially important, since raw wood parts change their geometric shape when dried. Simply put, the part can be twisted or curled up like a propeller. After the model is selected, it is necessary to start preparing materials.

Material selection and preparation

For making at home, it is best to choose pine blanks. They are the most commercially available and easy to handle. Suitable for children's, wardrobe hangers. Do not electrify when covered with a synthetic cover. Their advantages in comparison with other types of wood:

Parts manufacturing

This is the main operation on which the quality of the finished product depends. As can be seen from the drawing, you should prepare or buy wooden blocks and pine boards. They should not have knots larger than 5 mm. The wood must be dry. Curvature of bars and boards is not allowed. When buying, be sure to take into account those changes that have been made taking into account the specifics and binding to the place. A few tips:

• The bars should be with a small margin for processing. When buying, it is better to take two blanks for one part, taking into account possible marriage during work;
• Correct geometric shape. This is checked visually. Curved products are immediately visible;
• The length is taken with a margin of at least 3 cm. Carefully sawing off 5 mm at home with an electric jigsaw will not work;
• Round bars with a diameter of 18 mm will have to be looked for. If there is no such size, then these parts will have to be ordered;
• it is desirable to treat finished parts with antiseptic agents before varnishing;
• the cover can be made of fabric or other material.

For manufacturing, a minimum set of manual and mechanized tools is required:

Required materials for the manufacture of a dressing room or children's clothes rack:

• high-quality pine bars;
• self-tapping screws for wood;
• wood drills;
• varnish for pine wood and stain;
• hand carpentry tools;
• case.

Modern power tools are equipped with nozzles for suction of sawdust and dust from the working area using a vacuum cleaner. At home, this option is very useful.

We now have a set of blanks available. Prepare them in accordance with the dimensions according to the drawing. Symmetrical details compare. They must be the same. Cut to size, sand flat surfaces with a grinder. Curvilinear to process with sandpaper. This is the most labor-intensive part of making a suit floor rack hanger. When sawing, it may be found that the wood is damp in the thickness of the massif. In this case, it will be difficult to sand the surfaces. Such parts must be dried at room temperature before finishing. Depending on the degree of humidity, the drying process may take several days.

Assembling a dressing room floor suit hanger

This is the final step in the process of making a floor-standing clothes hanger. All parts are made according to the drawing and the conformity of the dimensions is checked, since they are all already indicated on the manufactured parts. You should pay attention to the quality of fasteners. That is, the choice of screws and self-tapping screws. General recommendations for choosing screws:

• The length should not exceed two thicknesses of the fastened parts. Otherwise, the screw will break through the surface of the second part and everything will be ruined. On pine parts, you do not need to drill a hole in the second fastened part;
• Choose the color of the screws in accordance with the color of the material coating;
• Self-tapping screws must be used for woodworking. The use of self-tapping screws for metal will significantly reduce the strength of the connection.

An important procedure is marking for drilling holes for fasteners. It is absolutely mandatory to use the hole location designation. You need to mark the place of drilling in such a way that the drill does not go awry. In this case, the strength of the connection of parts will be insufficient.

The diameter of the hole to be drilled for the mounting screws should be half the diameter of the screws themselves. The lack of holes can lead to splitting of wood in the process of screwing the self-tapping screw and the work will be spoiled.

Tips for tightening self-tapping screws with a screwdriver:

• Do not screw the screw all the way in. The screwdriver has a lot of torque and can turn the screw through the material.
• The final tightening of the fasteners should be done manually with a screwdriver so as not to turn the screw in the hole, since in this case the connection will lose strength.

When the floor hanger is assembled, it is sometimes necessary to varnish the joints with self-tapping screws. Screw heads should be level with the surface. These places should be passed with sandpaper and varnished along with a self-tapping screw head.

Features of children's floor clothes hangers

In addition to size, children's floor hangers are no different from adults. The thickness of the parts for the children's version can be reduced. Accordingly, the weight will be less, which will enable the child to move his own children's hanger. The dimensions of the children's floor hanger should be selected taking into account the size of the child's clothes. Designs for girls and boys may vary. It is advisable to provide in the design for the possibility of hanging hangers with clothes on a hanger, followed by covering with a cover. To do this, you can adapt two metal hooks on which hangers will hang. You can place the hooks on the back side of the structure or on the sides.

Other options for floor hangers for suits and clothes

Figured dressing room suit floor clothes hanger

This option looks original, but when made at home, some difficulties may arise with the manufacture of curved parts. It is difficult to maintain symmetry when working with a jigsaw. Both parts must be cut out by combining and fastening the two workpieces. The total thickness should not exceed the cutting depth parameter of the jigsaw. Modern household models are designed for a cutting depth of up to 70 mm, and this is quite enough. But this model is not suitable for shirts and blouses. That is, the possibilities of use are limited.

Mobile dressing rack on wheels

Another interesting model on wheels. The top of the design is crowned with regular hangers, which is very convenient for placing a jacket, shirts and blouses. And the pants are convenient to hang on the crossbars. Wheels are a good design find, since it is more convenient to roll a loaded hanger than to carry it. A cover made of film or fabric will conveniently cover the hanger.

This model is produced by IKEA in Russia as a suit and wardrobe floor hanger.

It's easy to make one with your own hands. Requires special fasteners. As you can see in the picture, the uprights must be attached to the base with metal screws. When manufacturing, you will need to carefully and accurately drill holes for the screws in the uprights. This is the only difficulty. Everything else is very easy to manufacture and assemble. The disadvantage is the need to disassemble the structure during transportation. You will have to unscrew the long bolts from the uprights.

Dismountable suit hanger rack floor in rustic style

This hanger is more suitable for a hallway or corridor. You can put shoes under it. In the manufacture of their own hands, this model is a significant difficulty. It is required to make holes of large diameter in the crossed round racks. In general, it is very difficult to drill holes in round parts with a household tool. Better not to try. To get around this unpleasant technological nuance, you can take non-circular square racks. Using a special drill, it is quite possible to make holes of the desired diameter in square bars. It is recommended to take a metal crossbar. The wood will bend.