Installation of edge tape on chipboard. Glue the edge on the tabletop with your own hands

Today, manufacturers of furniture structures use a large number of different materials to protect the end sections of products. The main purpose of the furniture edge is to protect a person from formaldehyde resin fumes. During the manufacture of furniture structures, you need to make the right choice of material and know how to glue the edge at home.

Types of PVC edges

A large number of multi-colored finishing materials are presented on the construction market. The furniture edge not only veneers end surfaces, but also is an element of a decor. Each type of edge differs in price, fastening, advantages and disadvantages. Consider the most common types of finishing material.

Melamine (unoflex)

The edge consists of several layers of paper. The top layer is considered decorative, as it contains a pattern that is glued to the substrate. The border is of two types - single-layer and multi-layer. Manufacturers produce tape with a thickness of no more than 0.6 mm, and a width of 16-55 mm. You can easily glue the edge on the chipboard yourself with an iron. The material is purely environmentally friendly, since there are no synthetic impurities in its composition. It should be noted that due to the insignificant thickness of the tape, paper structure, after 2-2.5 years it loses its aesthetic appearance. Manufacturers produce edging in coils of 200 megapixels, but in the distribution network it is sold from 1 megapixel. The cost of the tape is low. For example, the price is 1 Mp. edges 0.4 * 19 mm is 10 rubles.

PVC

The highest quality plastic is used for manufacturing. On the wrong side there is a primer - this is a relief pattern, a protector, which contributes to a better bonding of the border to the chipboard. The sides and grooves hide the presence of chips. This edging is quite laborious. On edging machines, manufacturers produce PVC tape with a thickness of 0.2 - 10 mm, and the width depends on the thickness of the chipboard sheet, which can be from 22 mm to 54 mm. PVC tape is sold with and without adhesive. The price of the edging material depends on its width and thickness. For example, if the edge width is 19 mm and the thickness is 0.5 mm, then the wholesale cost of a roll of 200 MP costs 400 rubles. Today, manufacturers have launched aluminum, chrome, and steel-colored edging on the market. Gluing the edge on chipboard at home is done directly into the sheet, which makes the product durable. In order not to melt the polymer, you need to monitor the temperature regime, which should not exceed + 45 ° C. The protective functions of the edging material are designed for at least 5-6 years.

ABS (ABS - Acrylonitrile / Butadiene / Styrene).

It is an impact-resistant thermoplastic that retains its appearance for a long time. It is not dangerous when heated and during processing, as it does not contain chlorine and heavy metals. The manufacturer produces a finishing material with a thickness of 0.4 mm, 1 mm, 2 mm. Do-it-yourself edging tape sticker is carried out on furniture structures that can withstand low temperatures and high humidity. For internal processing of furniture boxes, edging is performed with a tape of 0.4 mm, 1 mm, and for the front sides, 2 mm thickness is used. It should be borne in mind that when heated, shrinkage of the edge by 0.3% may occur. The edging material comes in different colors with a glossy, semi-gloss and matte finish.

Finishing material can be used to process a countertop, a kitchen or office table, a hanging shelf and other interior items. In each type of tape material, it should be noted a large assortment of colors. To decorate the surface, you can pick up a contrasting tape.

Required Tools

For edging the ends, it is not necessary to use professional equipment or seek help from the masters. If you need to update old items, you can independently paste the surface with multi-colored tape. The question arises: how to glue the edge to the chipboard? It is enough to have the essential tools at hand at home:

iron;
sandpaper (fine fraction);
file (optional);
stationery knife or scissors;
rubber roller (optional)
felt or other dense material.

Adhering to some rules, the product will turn out neat. To cut off excess tape, use a clerical knife, and to glue it with an iron.

When the edge on the furniture has peeled off, you can glue it again with a hot iron, and if it doesn’t work out, then remove the old edge tape with the same movements of the iron and change the old one to the new one.

Installation procedure

You can independently glue only melamine tape and U-shaped PVC - piping. Consider the technology of how to glue the edge. This method will help restore old furniture or decorate new.

Unwind a roll of melamine border. Attach to the end face of the surface to be treated. Mark the length with an allowance for trimming. The standard self-adhesive edge has a width of 2.1 cm, and the chipboard width is 1.6-1.8 cm.
Attach the tape, align the edge along one edge, iron it with an iron.
Iron in small sections of 10-20 cm.
Roll with a roller or rub the heated areas with felt.
Depending on the material chosen, it is necessary to glue the edge with an iron with a certain temperature regime. With a properly heated iron, the adhesive base will adhere evenly to the end without swelling.
After the tape has cooled, proceed to trimming and rubbing the protruding edge with sandpaper or a file.

You can see more clearly all the stages of work in the video below:

The stage of pasting the end surface is completed. The tape allows you to decorate the edges of various configurations. If you follow all the recommendations, the end will turn out to be of high quality, without scratches, minor defects and glue.

Edge tape for furniture is used not only by craftsmen who make furniture, but also for the restoration of wooden structures by home craftsmen. Any type of edge, which is applied to the chipboard end face independently or by furniture manufacturers, gives the product an aesthetic appearance. It also protects the structure from moisture, microorganisms, insects that can destroy the internal or wood structure of the product, so the edge sticker on the chipboard is a must.

It often happens that the furniture in the house is exposed to various kinds of influences: mechanical damage during rearrangement or moving, temperature changes (for example, in winter), excessive humidity.

Cabinet furniture deteriorates, and, as a rule, the ends of the chipboard “suffer”: chips, cracks form, and sometimes the poorly applied edge peels off.

The modern consumer is trying to save on everything, including the services of furniture studios. As a rule, this is caused by the idea that furniture makers "lift up" the price for their work, the fear of poor-quality repairs and, of course, the lack of free time.

Thus, the consumer is trying to solve the problem on his own, entrusting the repair of furniture entirely to himself or to familiar "craftsmen". Let's try to figure out what this can lead to.

First, it is worth noting that an ordinary person does not have any professional equipment at hand, as, say, in manufacturing enterprises. No machines, no suitable materials, which, by the way, are also not always available to the average consumer, and who does not understand them at all.

So, for example, not everyone knows that the pvc edge protecting the ends of the chipboard comes with and without an adhesive base. Not to mention the variety of edging material: from the simplest melamine edging to ABS edging.

What does the consumer do in this case? Trying to understand the intricacies spends a lot of time studying the issue. As a result, he decides to use improvised means.

It is also worth adding that not everywhere it will be possible to purchase an edge of the required color, which completely matches the color of the furniture. To do this, you need at least to know the nomenclature of decors of laminated chipboard of various brands.

Needless to say, not all sellers of fittings have an edge of the required color in stock and are ready to sell "by the meter". In today's economy, this is simply not profitable for most stores.

Now about the gluing process itself. To begin with, you will need to disassemble the furniture yourself, and after taking out the restored part, prepare it for further processing, which is already difficult at home: disassembled furniture takes up enough space at home, interferes with you and your loved ones.

To glue the edges with an adhesive base, many use a building hair dryer or iron. With the help of these devices, a strong heating of the adhesive layer occurs, after which such an edge should be immediately glued to the end of the chipboard. This must be done quickly, as the glue cools quickly enough.

Which, by the way, does not happen on the machine, where the glue is supplied from a special bath that maintains the desired temperature.

But, if even a very large slab is processed on a machine in a matter of seconds, then at home it can take much longer. After all, it is not only important to apply the edge very evenly on the end of the plate, it is also necessary to smooth it and press it in such a way that it does not move away before the glue hardens.

For gluing the edges without an adhesive base, some even use the popular Moment glue among the people. Which, although it grasps various surfaces quite well, is still not able to withstand heavy loads on the surface.

Thus, I would like to summarize the above, bringing together all the pros and cons of repairing furniture at home.

Minuses:

intense search and purchase of necessary materials for furniture repair
energy consumption for the operation of high-power heating devices
lack of skills and knowledge, time and place for work
a significant waste of time, effort and money.

Pros:

no need to contact "doubtful" companies
the opportunity to show off the result to friends. Of course, if such a result is achieved.

Otherwise, the consumer will simply lose a lot of time and nerves. You will have to get rid of damaged furniture and hastily purchase a new one. And this is already a lot of money.

So what's the best way to do it? Of course, we recommend always contacting professionals. Few people know, but now most of the ateliers provide such a service for edgebanding laminated chipboard.

What does it mean? And the fact that the specialists will select the edge of the required size and color, correctly stick it on the chipboard, carefully assemble and disassemble, and deliver the furniture.

Obviously, this is the best way to save time and money. If you still have doubts about the work of professional furniture makers, we recommend that you look at a professional machine.

In our company, you always have the opportunity to choose the desired color and decor of the edging material for almost any laminated chipboard. Full as always available on our website.

Making furniture with your own hands brings considerable cost savings. Basically, for this purpose, chipboard is used - a material glued from sawdust.

The main task of the furniture edge is the facing of the end surfaces of chipboard.

After cutting, its edges have an unattractive appearance and require further processing.

The tabletop is the most vulnerable element of furniture, and special attention must be paid to its edge.

At the moment, there are several ways to give the ends of the countertop an aesthetic look. For the manufacture of edges at home, only 2 of them are suitable:

Applicable edges

Modern technologies allow to produce various edges. However, not all are suitable for gluing at home. Melamine tapes are produced with a width of 19-54 mm. With a thickness of 0.2-0.4 mm, they allow you to ennoble the edges of the table top of various shapes.

A wide range of decors, which, in terms of color, most closely match the chipboard.

PVC strip of the same width may be slightly thicker. For gluing the ends of the countertops, edges are produced with and without an adhesive layer applied.

PVC plastic obtained by extrusion is able to withstand temperatures from minus 10 to plus 50 degrees.

Instruments

If you decide to glue the edge yourself, check the availability of tools. Prepare before you start:

In order to fix the PVC edges, you can use a clamp and a wooden block. If possible, use a hand router to finish the edge of the edge.

The milling cutter is expensive and it is unprofitable to buy it for one-time gluing.

Prepare your workspace, taking into account the space for turning the countertop. And, most importantly, buy the appropriate melamine tape or PVC edging.

Choose a ribbon that matches the color of the countertop.

Melamine tape

The cheapest and most affordable way to improve the edge. Does not require the purchase of glue and specialized tools. Everything you need can be found in any household, and the process will take a few minutes.

The edge processed in this way looks very neat.

It should be used to finish the inaccessible edge of the countertop. At the same time, do not forget about dampness, which will penetrate under the edge and destroy the material.

The technology of pasting looks quite simple.

pvc strip

A more progressive and aesthetically pleasing way. True, some skill is required to implement it, but after practicing on scraps, you can master this method.

The edge, resistant to abrasion and moisture, will ensure long-term operation of the tabletop in any interior.

When sticking PVC edge, follow the following sequence.

Properly selected and glued edge will give the tabletop an attractive look, and it will serve you for many years.

Such a smooth and neat edge can also be obtained independently.

VIDEO: Gluing furniture melamine edges with an iron.

50 original types of countertops:

Melamine edge, which you can buy on our website, is the most common and affordable edge material for furniture finishing. Such an edge tape is produced from a textured paper web by applying urea (melamine) resins to it. To protect the material from evaporation of melamine, a layer of special varnish is applied to it. A variety of colors and textures of the edging tape provides multi-color printing.

Which melamine edge to buy?

Melamine furniture edge is sold by manufacturers in two versions:

Edge without glue - designed for automated production. When applied to furniture, it requires specialized equipment to heat the granular adhesive.
Melamine edge with glue - can be applied to chipboard cut or furniture facade by direct heating.

On the website of MDM-Komplekt (Moscow) you can buy edging material wholesale and retail. Melamine edging with and without glue is sold in reels, the price of the product is per linear meter.

Why do chipboard edging and how to glue the edge with an iron

Chipboard is the most suitable material for the production of reliable and high-quality inexpensive furniture. In order to hide the not very aesthetically looking internal structure of the product, edging is performed from the end - the installation of special decorative panels made of melamine, PVC or other available types of synthetic plastics.

Why else edge furniture

In addition to the most obvious goal - to provide an elegant appearance, furniture edging performs several other equally important tasks:

Moisture protection. It is known that when wet, chipboard swells, loses its original shape and strength. The edge from plastic interferes with penetration of moisture from ends. This is especially true for rooms where water flows are constantly present - kitchen, bathroom, dining room, etc.

The edge, in addition to giving the furniture a finished look, performs several more important functions.

Insect and mold protection. The porous surface of chipboards is well suited for the propagation of various microorganisms that destroy the internal structure of the material. If a protective film is glued to the edge, the service life of the furniture will increase markedly.

The fight against harmful substances. As you know, in the production of chipboard, formaldehyde resins are used, the vapors of which can be released during operation through open ends. The edging tape prevents these substances from escaping into the environment.

to the menu

Where to hem

Furniture manufacturers often edging only the visible parts of the end surfaces. From the point of view of economy, this looks quite understandable, but taking into account the above facts, this approach can result in certain problems - the protective edge must be present in all places where there is an open internal chipboard structure.

If you purchased furniture with unprotected edges, it is quite possible to do their edging yourself at home. To do this, you do not need to have any special equipment - the edge can be glued with an ordinary iron.

Do not be too lazy to spend a few minutes on this operation - you will reliably protect yourself and your furniture and significantly extend its service life. Next, we will analyze in detail how to properly glue the edge tape with your own hands.

Edge materials

The edging of open surfaces of furniture can be done using various decorative elements, differing in material quality, appearance and, accordingly, cost.

Melamine tape. The simplest and cheapest edge. It is used in budget products and can be destroyed by moisture or mechanical stress. The main advantage of such a tape is the price and ease of application.

Advantages and disadvantages of melamine edging

PVC edge. May be 0.4 or 2 mm thick. It is customary to glue a thicker tape on the front surfaces, and a thin one - on hidden ends. Such an edge protects furniture well from chips and shock loads, but it is difficult to glue it at home - this requires special equipment.

ABS plastic. The most durable option. Edging with plastic is made only in production.

T-profile. It was used in the past, when there were few specialized edging machines, and milling machines were in every workshop. A cutter cut a longitudinal groove in the end, into which the edge is inserted.

Applied T-Profile. Edging with a T-profile is the most convenient option for independent use. It is enough just to stick it on the end of the chipboard with liquid nails or glue. The disadvantage of this solution is the edge protruding above the surface, which increases the thickness of the product and after a while becomes clogged with dirt.

to the menu

How to glue the edge with an iron

Edging in production is done with a tape with a clean base. The adhesive composition is applied to it during installation at a high temperature, which ensures the formation of a thin, even layer. In order to stick the edge, several rollers are used, tightly pressing it to the base of the chipboard. Then special cutters cut the tape to the size of the part, remove the remnants of glue and base material and grind the junction until a smooth and beautiful surface is obtained.

You can also glue the edge at home. To do this, you need to use a tape with an already applied adhesive composition. Further, the process largely repeats industrial edging, since it is performed similarly:

Melamine tape can be glued with an ordinary household iron. To do this, it is necessary to cut off a piece of the edge with a margin in length and width, put it on the end face to be processed and gently smooth it with an iron. After passing through the iron, the heated surface must be pressed with a wooden block or any other object that can transfer the necessary load.

When heated, the glue firmly glues the edge to the chipboard

After the chipboard edge tape is glued, it is necessary to cut off its hanging ends and process the edge surface. The tape is cut with a sharp knife, located strictly perpendicular to the plane of the end.

The edge trimming knife must be very sharp.

After cutting, the edge must be sanded. This can be done using a bar with fixed sanding paper.

You can find more information about the process of gluing edges on chipboard below:

Sticking a U-shaped profile on the end of the chipboard is somewhat easier. We have discussed this method before. Such an edge is much stronger than melamine, bends quite easily and reliably protects against damage.

The presence of micro-gaps between the edge of the U-profile and the front surface of the chipboard does not allow gluing it in the kitchen or in the bathroom, therefore, edging with this material is mainly used for office furniture.

Edging chipboard, of course, is best done in the factory. In production, you can order a tape from any materials, including plastic, PVC and other modern composite materials. Edge banding on the machine will ensure perfect evenness and accuracy of applying decorative cladding, but it requires certain costs. If the main task is to meet a predetermined small budget, applying a melamine tape with your own hands will allow you to combine acceptable quality and the lowest price.

Edging tools:

Iron. Any will do, but preferably small, without steam holes and with a thick sole. It is important that the soleplate of the iron is clean and without deep scratches.
Knife. You can work with an ordinary clerical (construction) knife, which will be discussed below. Also, a shoe knife and a knife from a planer are suitable. There are special ready-made devices for fast edge trimming, for example, from Virutex.
Bar with sandpaper. You can buy ready-made or make it yourself by sticking a piece of sandpaper on a workpiece that is suitable in size (it is convenient when the bar has sandpaper of different grain sizes on different sides). The recommended grain size is 150 units.

Edge technology.

It should be said that the quality of the edging largely depends on how well the chipboard is cut. The surface of the end face of the part should be flat, without a visible step from the scoring (saw) disk of the panel saw, there should be no obvious chips of the laminate and “lifting” of the laminate when the chip had just begun to form. High-quality and fast cutting of chipboard is carried out only on special equipment. The edge must be used with pre-applied adhesive. Edgebanding is sold in coils of 200 pm, but almost always it can be bought in 1 pm or more. A typical melamine edge has a width of 19 mm and a thickness of 0.3-0.4 mm (excluding adhesive thickness).
The process of processing the edge of one end of the part consists of the following steps:

The part is installed vertically in an improvised holding device so that the end face being machined is on top.
The edge segment is measured 2-4 cm more than the length of the machined side of the part.
The edge is placed exactly in the center on the end of the part, with equal releases along the edges.
Holding the position of the edge on the part with one hand, the edge is smoothed with a hot iron (the temperature of the iron is selected experimentally; if the temperature is too high, the edge starts to bubble, if it is low, it sticks badly or for a long time). It should be pressed with moderate force on the iron. Excessive pressure may cause edge displacement, insufficient pressure may cause non-glue. Indirect confirmation of good edge heating can be slightly squeezed out glue from under the edge. Particular attention should be paid to the ends of the edge and the points of contact with the laminated surfaces of the part.
After warming up the edge, it must be cooled. A small cloth is suitable for this operation. The edge is smoothed with a cloth, pressing lightly so that the edge does not move away when cooling. After the edge has cooled down to about 50 ° C (it makes no sense to wait until the edge reaches room temperature), you can begin to cut off the excess.
First remove the excess from the ends. To do this, the free ends of the edge are gently bent down, the edge is broken, the fracture site is lightly sanded with an emery bar and the excess is simply torn off. It remains to work a little more with an emery bar so that the edge is flush with the mating side (does not protrude or cling).
To cut off the excess edge along the length, it is necessary to set the knife blade at an angle of approximately 45 ° (see photo) and draw the knife along the end of the part. Angle of inclination (adjacent) relative to the plane of the part is determined experimentally (depending on the knife). This operation requires skill and practice. It is important not to damage the laminate (do not chip). After cutting off all the overhangs, you need to slightly process the edges of the end of the part with a bar with sandpaper, and the edging can be considered complete. Excess glue can be easily removed with a cloth soaked in acetone or gasoline. If a local non-glue is noticed, then the problem area must be heated with an iron and pressed again with a cloth. Also, by reheating, the edge can be completely removed from the part.

Edging kit: iron, knife, bar with sandpaper.

Bar with glued sandpaper.

In the manufacture of furniture from laminated chipboard, the edges of parts without processing have an unsightly appearance. To put them in order, a furniture edge and a profile are used. It is more convenient to work with them on special equipment, but you can also achieve good results with your own hands at home.

Types of furniture edges

One of the most popular materials for making furniture is chipboard. Its disadvantage is the ugly edges that remain when cutting the part. These edges are masked by the furniture edge. They make it from different materials, respectively, it has different properties and price.

Paper or melamine edges

The cheapest option is melamine impregnated paper edges. Paper is taken with increased density, impregnated with melamine to increase strength and pasted on papyrus paper. Papyrus can be single-layered (cheaper) and double-layered. To prevent the melamnov coating from being erased, everything is covered with a layer of varnish. To make it more convenient to edge parts, an adhesive composition is applied to the reverse side of the melamine furniture edge. When working, it is only necessary to warm up this composition slightly and press it well against the end.

Paper or melamine edging - the cheapest, but also the most short-lived option for finishing the ends of furniture

The thickness of paper edge tapes is small - 0.2 mm and 0.4 mm are the most common. There is no point in doing it thicker, and it will turn out expensive.

This type of edges is distinguished by the fact that it bends very well and does not break when bent. But its mechanical strength is very low - the edge is quickly worn out. Therefore, if it is used, then only on those surfaces that are not subjected to stress. For example, on the back of shelves, countertops, etc.

PVC

Polyvinyl chloride, which has recently become widespread, is also used in the production of edges for furniture. From the mass painted in a certain color, a tape of a certain width and thickness is formed. Its front surface can be smooth monophonic, or it can be textured - with imitation of wood fibers. The number of colors is large, so it is easy to choose the right one.

PVC furniture edge is the most popular material used by both home craftsmen and professionals. This is due to the relatively low price and good performance properties:

PVC furniture edge is available in different thicknesses and widths. Thickness - from 0.4 mm to 4 mm, width from 19 mm to 54 mm. The thickness is chosen depending on the expected mechanical load or appearance, and the width is slightly larger (at least 2-3 mm) than the thickness of the workpiece. There is a furniture PVC edge with an applied adhesive composition, there is - without. Both can be glued at home (more on that below).

This type of edging material also has disadvantages: not very wide temperature range: from -5 ° C to + 45 ° C. For this reason, furniture cannot be left outside in winter, and when pasting with heating, you must be careful not to melt the polymer.

Made of ABS (ABS) plastic

This polymer does not contain heavy metals, is characterized by high strength and durability. The disadvantage can be considered high price, therefore it is used extremely rarely, although it has excellent properties:

This type of edge can be matte, glossy, semi-gloss. There are also options that imitate different types of wood. In general, this material is more convenient to work with and more durable in use.

Veneer edge

Veneer is a thin slice of wood that has been dyed and shaped into a ribbon. This furniture edge is used in production when pasting slices of veneered products. Working with this material requires certain skills, and the material is expensive.

Veneer is not the most popular material for edging

Acrylic edge or 3D

Made from clear acrylic. A pattern is applied on the reverse side of the strip. The polymer layer on top gives it volume, which is why it is called a 3D edge. It is used in the manufacture of furniture in an unusual design.

Furniture edge profiles

You can finish the edge of furniture not only with an edge tape. There are also furniture profiles that are mechanically fastened. They have two sections - T-shaped or U-shaped (also called C-shaped).

A groove is milled under the T-shaped furniture profiles in the processed edge. A profile is hammered into it with a furniture (rubber) mallet. The edges are cut at 45° to make the corner look attractive. It is brought to perfect condition with fine sandpaper. This type of profiles is produced from PVC and aluminum, with the same installation method they look very different, and the differences are significant.

In width, they are available for chipboard 16 mm and 18 mm. There are also wide ones, but they are much less common, since they work less with such material.

C- or U-shaped profiles are most often mounted on glue. They coat the edge with them, then put on a plastic profile, press well and fix. These PVC profiles are soft and hard. Rigid ones bend worse and it is difficult to paste over curved edges with them. But they have great strength.

If you still need to "plant" a rigid C-shaped furniture profile in a bend, it is heated with a building hair dryer, then given the desired shape and fixed with masking tape until the glue dries.

We glue the furniture edge with our own hands

There are two technologies for gluing furniture edge tape. The first is for those who have glue applied on the back. In this case, you need an iron or a building hair dryer. The second is for sticking tapes without glue. In this case, you need a good all-purpose glue that can glue plastics and wood products and a furniture roller, a piece of felt or a soft rag so that you can press the edge well against the cut.

On the front ends of the facade and drawers it is better to use PVC 2 mm, and on the visible sections of the shelves - PVC 1 mm. The color is chosen either to match the main surface or “in contrast”.

How to glue the edging with glue yourself

The adhesive composition is applied to the melamine edge, it happens on PVC. If you have chosen PVC, it is easier to start with thin ones - they are easier to process, any melamine ones are easy to glue.

We take an iron and a fluoroplastic nozzle on it. If there is no nozzle, a dense cotton fabric will do - so as not to overheat the tape, but to melt the glue. For this purpose, a building hair dryer is also suitable. We put the iron on about “deuce”, while it is heated, cut off a piece of tape. Length - a couple of centimeters more than the workpiece.

We apply the edge to the part, level it, smooth it. Small pieces should hang down from both sides. We take an iron and, through a nozzle or a rag, iron the edge, warming up until the glue melts. It is necessary to warm up evenly over the entire surface. After the entire edge is glued, let it cool. Then we start processing the edges.

The edge can be cut with a knife, both sharp and blunt side. Someone uses a regular metal ruler, someone is more comfortable with a stainless steel spatula.

So, we take the tool of your choice, cut off the hanging edges of the edge. They are cut close to the material. Then cut off the excess along the part. Melamine and thin plastic are perfectly cut with a knife. If the PVC edge is thicker - 0.5-0.6 mm or more, difficulties may already arise. Such edges are possible, if any. This guarantees a good result in a short time. Longer processing will last if you use sandpaper, but the result may not be worse.

One important point: when gluing thin edges, the cut of the part must be even, without protrusions and depressions. The material is plastic, because of which all defects are visible. Therefore, first go through the cuts with sandpaper, then carefully dedust, degrease. Only after that you can glue.

Edging with PVC tape (without adhesive on the reverse side)

With this method of self-gluing PVC edges, you need universal glue and a piece of felt or rag. We read the instructions for the glue, perform all the actions on the recommendation. For example, for Moment glue, it is necessary to apply on the surface and distribute the composition, wait 15 minutes, press the surfaces to be glued strongly.

If you notice an error, select a piece of text and press Ctrl + Enter

Why do chipboard edging and how to glue the edge with an iron

Why else edge furniture

In addition to the most obvious goal - to provide an elegant appearance, furniture edging performs several other equally important tasks:

Moisture protection. It is known that when wet, chipboard swells, loses its original shape and strength. The edge from plastic interferes with penetration of moisture from ends. This is especially true for rooms where water flows are constantly present - kitchen, bathroom, dining room, etc.

The edge, in addition to giving the furniture a finished look, performs several more important functions.

to the menu

Where to hem

Edge materials

The edging of open surfaces of furniture can be performed using various decorative elements that differ in material quality, appearance and, accordingly, cost.

Melamine tape. The simplest and cheapest edge. It is used in budget products and can be destroyed by moisture or mechanical stress. The main advantage of such a tape is the price and ease of application.

Advantages and disadvantages of melamine edging

ABS plastic. The most durable option. Edging with plastic is made only in production.

to the menu

How to glue the edge with an iron

Melamine tape can be glued with an ordinary household iron. To do this, it is necessary to cut off a piece of the edge with a margin in length and width, put it on the end face to be processed and gently smooth it with an iron. After passing through the iron, the heated surface must be pressed with a wooden block or any other object that can transfer the necessary load.

When heated, the glue firmly glues the edge to the chipboard

The edge trimming knife must be very sharp.

After cutting, the edge must be sanded. This can be done using a bar with fixed sanding paper.

You can find more information about the process of gluing edges on chipboard below:

Our offer

In the online store of the company "21st century" you can buy edge tape for furniture at reasonable prices. We sell this material wholesale and retail, providing discounts for large orders. In our catalog there are melamine edges. These products are paper tape impregnated with melamine resins. Hot-melt adhesive is applied to the reverse side of them. Edge tape can be purchased for cladding furniture for the kitchen, living room, bathroom and other rooms. As a rule, it is used in the manufacture of cabinets from chipboard.

If you want to buy edging or other furniture fittings in our online store, just add the selected items to the "Basket" and fill out the online application. If you have any questions regarding the range, current prices and terms of cooperation, call the managers of our company at the numbers listed in the "" section.

If you yourself make furniture from laminated chipboard or MDF, then after cutting the sheets, you need to protect their end parts, which will increase the service life of the product and give it a beautiful appearance. For this, PVC edge for furniture is often used, but there are other varieties. In this article we will talk about all types, the need for edging and how to stick it with your own hands.

Self-adhesive furniture edge - a narrow strip of melamine, PVC, ABS or other material. It protects and decorates the place of the cut. In the production of cheap furniture from laminated chipboard, an edge is simply necessary, as it protects people from exposure to harmful formaldehyde. In addition, it gives strength and protects the material from moisture ingress.

Edge types

The following types of furniture edges are most popular.

For gluing on the machine, a special melt adhesive for PVC edges is used. It is sold in the form of granules, after heating it becomes liquid. The adhesive is applied to the tape either when heated or during the manufacture of the tape.

Edging chipboard

In order for the edge for a tabletop or cabinet to be beautiful and durable, the best way is to order edging in production. Usually this is done in the same place where chipboard is bought and ordered.

Approximate prices for application (per 1 linear meter together with the material):

PVC edge 2 mm - 40 rubles;
PVC edging 0.4 mm - 25 rubles;
edge for chipboard made of melamine - 25 rubles;
in addition, you will have to pay for the processing of curved sections.

Rehau PVC edging is the most popular in Russia, it has a wide range of colors, so you can choose a color for any laminated chipboard. The width of the tape is different - from 15 to 45 mm.

To order this service for a store, you must first prepare a diagram of how to glue the PVC edge: in what places to apply it and what thickness. Those places that will not wear out can be covered with 0.4 mm PVC to save money (for example, back and bottom edges). All visible places are treated with PVC 2 mm. Where the joint will be attached to the joint with another part, processing is not needed.
The difference between PVC coating 0.4 and 2 mm
Let's take an example.

On the inner inset shelf, only the front face is processed with a layer of 2 mm.
Top overlay cover - from all sides (rear face 0.4 mm, the rest - 2 mm).
The front of the drawer is processed on all sides with a thickness of 2 mm.

To simplify the calculations, you can use special furniture programs, they create a project automatically. As a result, in order to assemble an average wardrobe, a PVC edge for chipboard will cost 1.5-2 thousand rubles. It will not be very cheap, but it will be of high quality, safe and durable.

Glue the edge yourself

For those who want to save money, there is a melamine edge with glue, which is glued with an iron. This option is quite suitable for repairing old furniture - do not carry a few small boards into the workshop. To solve the question of how best to glue the edge to the tabletop, it is better not to be too lazy and turn to production, or still use an overlay profile, because melamine will quickly deteriorate from moisture and abrasion.

For gluing, an old Soviet iron or a building hair dryer is best suited. The thermostat of the iron is set to about 2.5 positions. In addition, you will need a rag, a knife, fine sandpaper and a stand for fixing parts.

You can also use an iron to remove the old edge tape. To do this, it is heated and pry with a spatula or knife.
In this video you can see how to stick a 2 mm edge at home:

To achieve a really good result, it is still better to order factory edging. The overpayment will not be too big, but the durability will increase significantly. Now on sale you can find almost any color of tape to imitate wood or a plain version.

Melamine edge, despite the fact that it was invented a long time ago, is still widely used in the manufacture of modern cabinet furniture. Also today, its competitors (PVC and ABS edges) have appeared and become widespread, which, however, do not affect the popularity of melamine edges.

Among its main advantages, one can single out such qualities as low cost and ease of sticker and processing (no complicated equipment is required, everything that is needed is available in any modern home - but we'll talk about this a little later). The main disadvantage of such an edging material is its low mechanical strength (where PVC is only slightly washed out, melamine will break off).

In general, this type of edging materials has firmly established itself in small workshops and does not intend to leave them.

We will analyze the process of edging with a melamine edge in detail. The edge itself is sold with hot-melt adhesive applied to its inner edge (visible in the photo as a fine mesh).

For work, we need an iron, scissors, a metal ruler, a block with fine sandpaper and a glove. It is enough to pull the glove on the left hand (there will be a tool in the right hand).

We put the part on the end (you can fix it in a vice or other clamp so that it does not fall). We put an edge on it, making a small overhang from the end.

We iron the edge heated to medium values (when overheated, the glue boils and the edge bubbles, after which it can be torn off and thrown away) with an iron, the edge first towards the left hand.

Unfortunately, both hands do not get into the frame, since I still cannot work with them and the camera at the same time.

At the same time, it is advisable to hold the iron perpendicular to the part with the spout toward you (the fact is that Soviet models have a slight concavity on the sole, which prevents the edge from being pressed tightly against the surface, but back and forth so that the wire does not interfere with work). Maybe you will find a more comfortable position for the iron, but this is how I do it. The first movement of the iron goes to the left hand, while it aligns the position of the edge. In this case, the tape initially adheres to the surface. Then we lead the iron in the opposite direction, rolling it with the palm of the left after it.

We remove the iron and continue to press the edge until the glue cools (4-6 hand movements).

With scissors, cut the tape "to the edge" from the main tape.

Immediately turn the workpiece over and cut off the edge on the reverse side.

Thus, overhangs are removed from the ends of the workpiece. And it turns out flush with its butt. For this, manufacturers offer special end cutters, but, as can be seen from the photo, it turns out no worse with scissors.

Now we move on to removing overhangs from long edges. To do this, we lay the workpiece on the face so that the edge hangs from the workbench (so we do not risk breaking the overhang).

A simple metal ruler or square is taken in hand (many people use knives, pieces of iron from planes and other exotic things, but I prefer the ruler, because sharply sharpened pieces of iron, at the slightest change in the angle of cut, strive to either move up or, worse, crash into the material of the part, damaging the laminate (a ruler cannot do this).

The square is placed on the face of the workpiece at an acute angle to the edge (as in the photo) and the excess tape is cut off with one movement. At the same time, it should not be bent - the ruler should be tightly pressed to the surface of the workpiece. Together with the overhang of the edge, excess glue is also cut off, which often protrude from the junction.

In principle, the edge already turns out to be quite even. But to achieve the best effect, it should be polished.

To do this, we take a sanding block with a fine grain (P180, for example) in our hands and make one or two (no more) movements, at an angle of 45 degrees to the workpiece, smoothing the edge and removing possible burrs.

Sometimes there is such a thing as non-glue. It becomes clearly visible just after the removal of the overhang.

Again we pick up the iron and warm up the defective place, at the same time pressing the edge.

Then again with the palm of our hand we strongly press the edge tape to the workpiece. As a rule, this is enough.

Now the formation of the edge joint in the corners. The edge (it is advisable to immediately cut it off with a small allowance - it is more convenient to work with short segments) is applied to the workpiece.

It is pressed with an iron and also rolled with a palm. The result is such a joint that needs to be finalized.

With scissors, laying the upper branch on the edge of the workpiece strictly parallel to it, cut off the excess.

There remains a small (no more than 0.5 mm) residue.

We cut it by tilting the scissors at an angle of about 30 degrees.

The result is a joint like this. From the end, it also remains to cut off the excess tape with a ruler according to the method described above.

Furniture is an important element not only in the apartment, but also in other rooms. It is used in offices, educational and medical institutions, etc. Today, her choice is quite large. Products differ in design, size, materials from which they are made, and so on. Thus, it will not be difficult to choose the option that you need specifically.

Based on what material is used in the manufacture of furniture, its cost is also determined. If we talk about inexpensive products, then they are mainly made with chipboard. This material is quite durable and wear-resistant. Great for furniture production.

But its interior does not look quite aesthetically pleasing. To hide this, additional actions are carried out, which are called edging. They consist in the installation of special decorative panels from the side of the end. Different types of synthetic plastics cope with these tasks perfectly. For example, melanin, PVC and more.

Melamine edge with glue: advantages

The choice of edging materials that can be used in the manufacture of furniture is large. If we talk about which is the most popular, then this is a melamine edge. Basically, it is her preference. No wonder. After all, it has a lot of advantages. The main one is the cost of the product. It is quite low, so it is accessible to everyone. In addition, it is worth noting the simple technology of use. To carry it out, you need simple tools that are in almost every home. At the same time, in order to perform edging with this material, special skills or work skills are not required. It is within the reach of everyone.

In addition, it is worth noting its advantages such as reliability and practicality. It is resistant to moisture and other adverse conditions. Perfectly protects furniture from them. However, her selection is huge. Different textures, colors, etc. will help you choose it for any type of chipboard.

Of course, like any other material, this one has its drawbacks. First, it is very thin. Secondly, the drawing does not hold up well. Thus, do not count on its long service life.

Melamine tape with glue: edging features

Before you get started, you need to decide what tools will help you do this job. If melamine tape is selected for edging, an iron is required. It is better to give preference to a small device. At the same time, it is important that its sole is thick and without damage and stains. An iron that was produced 30-40 years ago is perfect for such purposes. These products meet these requirements.

Another tool that will be required for this work is a knife. But here the usual kitchen will not work. It must be shoe or clerical. You can also use a planer knife. There are also special tools that are designed for these purposes. These knives are manufactured by Virutex.

And, of course, a bar with sandpaper. You can buy it or make it yourself. If the second option is chosen, then it is necessary to glue sandpaper on a bar of a certain size. In this case, you can use its different grain size. Stick paper on all sides of the bar. The most suitable grain size of 150 units for these purposes.

How to glue melamine edging?

The process of gluing the melamine edge is simple. Therefore, there is no need to seek help from the masters. It can be done by hand. You can see how to do this in the video below.

The quality of edging is influenced by various factors. The first and, perhaps, the main one is how the chipboard is cut. There are a number of requirements for the butt, which he must meet. So, it should be even, without steps and other defects formed after processing the sheet under the saw blade. Only in this case, the fit of the tape will be strong and reliable.

When choosing an edge, you should give preference to the one on which the adhesive has already been applied. You can find it in many hardware stores. It is presented in the form of a bay of 200 pm. But that doesn't mean you have to buy everything. You can take the size you need.

Process steps

To stick the tape, you must correctly place the part. That is vertically. In this case, the end face that is being processed should be at the top. Make sure the sheet is in a stable position so that it does not move. In this case, you can use a special device.

Then prepare the necessary piece of the edge. To do this, it is carefully measured and cut off from a common tape. Moreover, its length should be 3-5 cm longer than the side that is being processed.

You need to start gluing from the middle. A tape is laid on it, while the edges should be as even as possible. Then, holding with one hand, smooth the other with an iron that is preheated. Its temperature is chosen experimentally. As practice shows, a high one can lead to the appearance of bubbles on the edge, and a low one does not provide gluing.

Do not press hard on the iron, as the edge in this case may move. As a result, gluing will be crooked. But if you press lightly, then it will not stick. Moderate force is required.

You can also determine the quality of gluing in the process. During the ironing of the surface, glue should be squeezed out from under the tape. Particular care must be taken at the ends of the product and the place where it comes into contact with the surface that is pre-laminated, as these areas do not stick as well as others.

Now you need to leave the edge to cool. At this time, you need to smooth the surface with a rag. Thus, when cooling, the tape will not peel off. The duration of this procedure is short. As soon as the base reaches a temperature of 50 degrees, you can remove the excess that has formed around the edges.

Start from the edges. The ends that eventually remain must also be removed. Since the material has become hard, they break off easily. Then take a bar with sandpaper and process them. This will give the bar an attractive look.

If you approach this work responsibly and carefully, then the quality of its implementation will be at a high level. Moreover, it will be impossible to distinguish the result from the one obtained when using special edging equipment.

(LDSP) the edges of parts without processing have an unsightly appearance. To put them in order, a furniture edge and a profile are used. It is more convenient to work with them on special equipment, but you can also achieve good results with your own hands at home.