Modem sagemcom fast 2804 v7. Sagemcom router: step-by-step setup for a teapot

AnexA universal router [email protected], v7 is branded and fully optimized for the network of the leading Russian operator OAO Rostelecom. Maximum data transfer rate 300 Mbps.

Sagemcom [email protected] 2804, v7 and v7B can work both over xDSL technology and over utp cable. Those. There are WAN ports for both types of connection technology. This fact should be taken into account when configuring the connection. We will reflect this in the Internet connection settings item. I would also like to note that Sagemcom [email protected] 2804, v7 can only be configured for PPPoE connection or bridge mode.

Instructions for setting up a Sagemcom router [email protected] 2804 v7 and Sagemcom [email protected] 2804v7B

Authorization

In order to get into the web interface of the router, you need to open your Internet browser and type 192. 168.1.1 in the address bar, Username - admin , Password - admin(provided that the router has factory settings and its IP has not changed).

Features of setting modem + wi-fi router

1. This modem has an ip-address 192.168.1.1. Therefore, if you connect to Sagemcom 2804 router Asus, NetGear, Tp Link or ZyXEL(these models of routers have the same ip-address - 192.168.1.1) - do not forget to change the address of one of the devices to some other one, for example 192.168.0.1

2. There are two setting options:

• modem Sagemcom 2804 configures it in router mode (PPPoE Internet connection is created on the modem), and on the router select the Static IP (Static IP) or Dinamic IP (DHCP or Dynamic IP) mode;
• modem Sagemcom 2804 configure in bridge mode (bridge), and create an Internet connection (PPPoE) on the router;

3. If the subscriber has an IP-TV service, then on the modem Sagemcom 2804 DHCP will be disabled. Therefore, on the router, you select the connection type Static IP (Static IP) and prescribe ip-addresses manually.

Setting up Wi-Fi on the router

1. Find the menu item on the left WLAN setting;, in the window that opens, check that there is a check mark on the parameter Enable wireless; And Enable multicast transmission over wireless network (WMF);. SSID- the name of the wireless connection, leave it by default or change it to your own, press the button Apply/Save;

2. Next, open the Security submenu, on the left and in the tab that opens turn off the WPS option, check that authentication is selected WPA-PSK, encryption WPA-TKIP+AES. We either prescribe our own network protection with a key, or press the button opposite WPA/WAP To display, click here; and in the window that opens, rewrite the password. Click Apply/Save;

Internet connection setup

Before setting the router settings, you need to reset its settings to factory settings. To do this, go to Settings;→ Reset;→ Restore default settings;.

The window below will appear in front of you. We expect 2 minutes.

After resetting the default settings, you need to remove unnecessary add-ons from the router. Go to the tab. Next, check 3 checkboxes as shown in the screenshot below and click Delete;.

Next, go to the tab Additional settings;→ 2nd level interface;. Next, check the only checkbox as shown in the screenshot below and click Delete;.

Internet setup via xDSL

Additional settings;, Layer 2 interface;. We press the button Add; in the middle of the window.

We follow the setup wizard ;, we fix only 2 points VPI and VCI for the parameters that Rostelecom uses. Click Apply/Save;

We check that the appropriate layer 2 interface is selected (in our example it is 0_0_35) and press Further;

In the WAN service configuration, decide how the modem (router, bridge) will be configured and click Further;(see an example of setting by a router)

In the window that appears, enter PPP username;- login, PPP password;- password. PPPoE service name;- any. Put a tick in the box retry PPP on authentication failure; And Enable IGMP Multicast Proxy;, Further;

In the next two windows of the wizard; check that the created interfaces are in the left column. If they are in the right - transfer to the left, press Further;

Internet setup via ETTH

Go to tab Additional settings;→ ETH interface;. If this is empty, then add an entry. If Already available, then do not change anything (by default, a WAN port for eth0 is created - the first LAN port).

Go to tab Additional settings;→ WAN service;. Click Add;.

choose eth0/et0 Further;.

Put a dot on PPP over Ethernet (PPPoE), press Further;.

Type in section Username; enter the username of the subscriber, respectively, in Password;- subscriber's password, PPPoE service name;- int. Click Further;.

Then the left column Available routable WAN interfaces; highlight the item ppp1.1; and press the button <- . Click Further;. Similarly, then in the left column Available WAN interfaces; highlight the item ppp1.1; and press the button <- . Click Further;.

Setting up IPTV

Setting up IP-TV for different connection technologies is different.

Setting up IP-TV via xDSL

In the main window, click the menu item on the left Additional settings;, Layer 2 interface;. In the table that appears, if there are already configured connections for IP-TV, delete them (delete first in the WAN service menu, then in the Layer 2 Interface). Then we press the button Add; in the middle of the window.

We fix only 2 points VPI and VCI for the parameters used by Rostelecom. Click Apply/Save; at the bottom of the window (in the picture, the Rostelecom Omsk setting)

We add another interface to the WAN service configuration, where we check that the appropriate layer 2 interface is selected (in our example it is 0_1_36) and click Further;

For the modem to work correctly with STB set-top boxes (IPTV), you must go to the LAN parameter in the left menu and disable DHCP (Dynamic Host Configuration Protocol) in the window that appears. Then check that IGMP Snooping is enabled and click the button below Apply/Save;

Setting up IP-TV via ETTH

Go to tab Additional settings;→ WAN service;. Click Add;.

choose eth0/et0(or the interface you created above) and click Further;.

Put a dot on Bridging, press Further;.

Port Forwarding/Forwarding

Select NAT ---> Virtual Servers ---> Add

Use interface: select the interface you have created for the Internet (in our example it is xDSL)

Service name:- either choose from the list, or create your own.

Server IP address: address of the device on the network to which the request will be redirected

External portInternal port: range of ports to open

In the vastness of our market, a universal and inexpensive device has been noticed - a multifunctional ADSL router F st 2804 v7. In the version provided by Rostelecom, everything is perfectly configured from the included CD. But MTS today provides a similar device with an even greater set of features, but you need to configure it through the web interface. In general, the MTC Fast 2804 router creates an ADSL connection no worse than devices from Rostelecom. And how to set it up is discussed below.

Fast 2804 routers

In fact, all devices that have the word "Fast 2804" in their name are produced by one company - Sagem (in other words Sagemcom). Routers of versions v3, v5 and v7 have reached our country. They may differ in the shape of the body, in addition, the graphical interface is made for a specific provider. In general, these routers have the same capabilities. In terms of setup, the “from MTS” option is the most difficult, although it can create an ADSL connection. We are trying to configure this router to connect under the PPPoE protocol, in case the connection is provided by a telephone wire. Let's get started.

Setting Basic Functions

Connecting a router before setting up

We will configure the device from MTS like any other "home" router. First, we connect any LAN port with a PC network card with a complete patch cord:

Connecting the router to a PC

Then, connect a telephone cable to the ADSL port (you can use a splitter from the kit). At the final stage, power is supplied to the router (but first, you need to configure the network card in the PC):

Setting up a wired connection on a computer

This completes the preparatory steps. After turning on the router, you need to wait 2-3 minutes, after which, from the computer, you can enter the graphical interface.

Authorization in the GUI

On the computer, you need to open any browser (not lower than IE5), and go to the address: 192.168.1.1.

If everything is done correctly, an authorization window will appear. “admin” is suitable as a login (and “mts” as a password). If authorization is passed, the user will see the following tab:

Main tab of the web interface

The graphical web-interface is divided into tabs, which are combined into two lists: "Basic settings", "Advanced settings". The first list, as we can see, contains 5 different tabs. We will now look at how to set up an ADSL connection.

Connection setup (PPPoE option)

The F st 2804 router can connect to the Internet via a telephone wire or a 3G modem. We will consider the simplest configuration option, when the built-in ADSL modem is used to create a connection, and the provider's protocol is called "PPPoE".

Before setting up, it is better to write out on a separate sheet:

1. Name and password of the subscriber (there is in the contract);
2. The values ​​of the VPI and VCI parameters used by this provider (for example, 0 and 30);
3. PPPoE encapsulation type: LLC or VC-Mux;
4. For a permanent IP address (a separate service, usually provided for a fee), you need to know the value of the address.

The setting is made on the advanced mode tabs. Go to this list of tabs, turn on the English language. On the "Wan Service" tab, located in the "Advanced Setup" menu, you will need to remove (using "Remove") all existing interfaces:

WAN interface tab with "old" values

ATM interface tab

Here you have to do the same. Then, you need to go to the "Wan Service" tab again. And now - click the "Add" button:

A tab for setting up a new connection will appear, on which you can select a value, as in the figure:

Settings tab

Then, you need to click "Next". On the next tab, you need to set the VPI and VCI values ​​\u200b\u200b(instead of the numbers 1 and 91):

For example, if the values ​​0 and 30 are valid, the string will be "pppoe_0_0_30_3". Do not leave the values ​​"as is" - they do not match the user's provider.

In addition, the connection protocol is selected here (after selecting PPPoE, a list will appear where you need to select LLC or VC-Mux). After completing the settings, you can click "Next".

Connection Options Tab

The next tab sets the username and password. For a dynamic IP address, nothing else needs to be changed. "IGMP Proxy" can be enabled if you plan to watch IPTV. But for a constant IP value, you need to check the "Use static IPv4" checkbox, and fill in the field that appears.

After completing the settings, you must click "Next", and again "Next". A tab will appear where you can leave the automatic mode for obtaining DNS (or set certain address values). And the final tab looks like this:

The final connection settings tab

By clicking "Apply / Save", we get a new working connection.

Device Information Tab

The presence of a connection can be judged by the state of the main tab. Happy tuning!

Turn on the wireless network

Set up a Wi-Fi network - we will use "advanced settings". The "Basic" tab from the "Wireless" menu allows you to configure everything you need:

Setting up a wireless network

Let us explain the meanings of the parameters. "Enable Wireless" turns on the transmitter, and "Hide Access Point" will allow you to work on a hidden name.

The SSID field contains the network name (set as required). Country (Country) is better to set "RU". After completing the settings, the “Apply/Save” button is pressed. Wireless network - will appear automatically.

Note that the universal router F st 2804 has serious capabilities. For example, the device independently selects the least noisy channel (in the 2.4 GHz band). Automatic selection mode - can be disabled. The power of the transmitter is also adjustable. All these parameters are on the "Advanced" tab, but the user is not recommended to change them in the absence of proper qualifications.

The Security tab contains encryption options. We do not consider setting up network protection.

Additional features of the router

Setting up IPTV

Oddly enough, the Fast 2804 router creates Internet connections that are several times faster than 3-4 Mbps. Therefore, it is possible to view IPTV through computers connected to the local network. To enable this option, you must:

• When setting up the connection, check the “Multicast Proxy” checkbox (it was discussed above);
• On the LAN settings tab (“Advanced Setup” -> “LAN” among the “advanced settings” of the router), you need to check the “IGMP Snooping” checkbox:

LAN settings tab

After making these settings, you can watch TV through any computer connected to the router's network. Now, multicast packets used in IPTV get into the local network from the Internet.

Additionally, it is possible to restrict multicast traffic on the wireless network. To do this, you need to go to the "Wireless" -> "Advanced" tab (also located in the "advanced settings") to set the required value in the "Multicast Rate" list. An acceptable choice is 9, 11 or 12 Mbps, which is enough for FullHD viewing.

Question answer

Q: I can't access the GUI. The IP address 192.168.1.1 is not available.

You can try resetting the router to factory settings. To do this, after switching on, you must wait 2 minutes, then press the "RST" button on the rear panel (holding it for 15-30 seconds).

Question: what is the speed of wireless connections, was it not said about the choice of mode (N / G / B)?

This router works in "mixed" B / G / N mode, the maximum transmission rate in the wireless network is 65 Mbps. The use of the "N Only" mode (only N) is not provided.

How to remove the router from the package and connect it correctly is shown in the video:

This review will step by step review and describe the Sagemcom F ST 2804 V7 setup. This is an entry-level router, which is often sold in addition to the services provided by domestic providers. These include the nationwide MTS and Rostelecom. It is on the example of configuring the connection of such a router to the network equipment of the last company that this material will be presented.

Network Gateway Package

Standard and typical delivery list for this router. Separately, it should be noted that such a network gateway is tied to the equipment of a particular provider. That is, if the router is designed to work in combination with the software and hardware of the Rostelecom company, then it will only work in such a bundle.

The delivery list includes a Sagemcom F ST 2804 V7 router. Setting up a Rostelecom connection is described in detail in the instruction manual. The manufacturer did not forget to include a warranty card in the package, the validity of which is 1 year. This is a complete list of the configuration of this solution. This list is supplemented by a power supply with a 0.5 A output and an interface cord, which is mainly used at the stage of setting up a network connection.

Also in the delivery list there is a CD with specialized software. By default, the hero of this article has the V5 software version, which cannot work normally with Rostelecom equipment. Therefore, it is necessary to upgrade the router considered in this material to version V7.

main parameters

The main parameters of this router are as follows:

• Three possible ways to connect to the Internet: Ethernet, ADSL and 2G / 3G (in the latter case, you must additionally purchase an external modem and a starter pack to be able to connect to a cellular network).
• Four ports of the RJ-45 format, which can be used both for connecting computing devices using twisted pair to the global web, and switching set-top boxes.
• One USB standard port, which is used to connect a modem.
• A wireless network based on a Wi-Fi transmitter, within which information can be transmitted at speeds up to 300 Mbps.

The body of this device is plastic. May be white or black. Information LEDs are displayed on one side of it. The first of them indicates the presence of power, the second indicates an active ADSL connection, the third indicates the presence of receiving information from the Internet. The next information indicator indicates the operation of the wireless network. Then there are four LEDs that characterize the functioning of the wired segment of the internal computer network. The last light element in this case shows the operation of the USB port built into the router.

On the top side of the device are a USB connector and two buttons. One of them includes a network gateway of this model, and the second uses the technology of automatically connecting the device using Wi-Fi.

On the opposite side face from the information panel, all connection ports are displayed. These include an ADSL connector, a USB port, and 4 RJ-45 ports. There is also a power socket here. There is also a button to reset the software to its original state.

Connection

At the first stage, setting up the Sagemcom F ST 2804 V7 comes down to making the following connections:

1. We install the router at the place of use. The latter must meet the following requirements: an outlet must be located as close as possible, an ADSL input wire and interface cords from computers must be connected.
2. Next, connect the power supply.
3. Then it is necessary to carry out switching with the equipment of the ADSL provider.
4. The last stage is the collection of the wired part of the computer network.

Setting up an external wired connection

At the first stage, you need to update the software shell of the router. To do this, on the PC connected to the network gateway, launch the CD and in the autorun window that opens, select the “Update router” item and wait for this operation to complete.

Then setting up the Sagemcom F ST 2804 V7 comes down to configuring the external connection. To do this, we re-initialize the launch of the CD and select the “Full Setup” item in its menu. In the future, follow the instructions of the wizard and set the connection parameters, which can be taken from the contract with the provider for the provision of services. At the end, save the entered data and exit the setup wizard.

Modem setup

The next step is to configure the Sagemcom F ST 2804 V7 modem, which is used to implement a backup method for connecting to the Internet. It consists of the following actions:

1. Choose a supported 3G modem model, purchase it along with the starter pack. We collect everything together and connect to the router.
2. We launch any available browser on a PC that is directly connected to the network gateway.
3. In its address bar, enter the device address in the format 192.168.1.1.
4. Next, in the request window in the fields "Login" and "Password" you must enter admin. After that, press the "Login" button.
5. Go to "Advanced Settings" and select the "3G Configuration" sub-item.
6. Then we set the PIN code for the installed SIM card.
7. We save the data and exit the program shell.

Setting up an internal connection

The wired connection is automatically configured, and there is no need to perform any additional manipulations with the Sagemcom F ST 2804 V7 program parameters. Wi-Fi setup is also automatic. The only thing you will definitely need is to rewrite the network name and password to connect to it from the bottom cover of the device case. In the future, simply enter them in the appropriate request.

IPTV

The router in question supports IPTV technology, with which you can watch television programs. In this case, the step-by-step configuration of the Sagemcom F ST 2804 V7 router is performed as follows:

1. We go into the router settings menu according to the previously given method.
2. After opening the settings interface, you need to go to the sub-item "Advanced Settings". Then you need to select "Interface grouping".
3. At the next stage, click the "Add" button and set the connection port of the IPTV set-top box.
4. Save the settings and exit the setup interface.

Price

At the moment, such a router can be purchased for 1200-1500 rubles. Again, it is advisable to purchase such a solution only if Rostelecom acts as a provider of Internet traffic. Given the functionality of the device in question, such a cost is fully justified.

Conclusion

Sagemcom F St 2804 V7 is a very high-quality, functional and at the same time very affordable network gateway. Setting it up is a fairly simple operation, and every user is able to handle it. The provider at the same time simplified the process of its implementation as much as possible. Therefore, such a router is simply ideal for creating home computer networks.

Open your browser and type 192.168.1.1 in the address bar. To enter the settings, use the login admin, password admin.

The router configuration settings for connecting to the Internet consists of 3 steps:
1. Deleting the previous configuration.
2. Setting up the physical interface (configuring the interface of the 2nd level, indicating which LAN port will be used as the WAN port for connecting the cable FTTB).
3. Configuring the logical WAN interface to work with the physical interface specified in paragraph 2 (configuring the WAN interface with setting the parameters for connecting to the Internet).

It is necessary to delete all previously created logical interfaces set by default in the configuration and create a new layer 2 interface (ETH WAN) to connect to the Internet. To do this, go to the menu item Additional settings -> WAN service, set the checkboxes in the Delete column, in each line with interfaces, and click the "Delete" button.
Next, you need to configure a new physical interface to connect to the Internet. To do this, enter the menu item Advanced settings -> Layer 2 interface -> ETH interface and click the "Add" button.

Parameter selection window will appear ETH WAN in which you need to select the ETH port and connection mode. Since port number 4 on the router will be used as the WAN port for connecting to the Internet, you must select as the ETH port eth3/eth3.

If there is an option VLAN MUX(Several connections through one vlan), then you need to activate it. To save the settings, click the Apply/Save button. Then the interface will be created

After creation ETH layer 2 interface must be created WAN service. To do this, enter the menu item Advanced settings -> WAN service and click the "Add" button

After that, the WAN service interface configuration window will appear in which the layer 2 interface created in the previous step should be selected (in our case it is eth3 / eth3)

On the next page, the WAN service type should be selected − PPP over Ethernet. Leave the WAN service description field unchanged.

In the PPP username field, the Client enters the login, and in the PPP password field, the password given at the conclusion of the contract
In the “Routing-Default Gateway” window, the selected default gateway interface should be the created WAN interface ppp1.1

In the window for selecting the interface of the DNS server, ppp1.1 should also be on the left side

To apply the settings, click “Apply/Save”

Setting up IP TV

To connect the STB set-top box, you need to configure the corresponding virtual interface (WAN service) on the router. By default, the cable from the STB set-top box should be connected to LAN #1 of the router). If you need to connect several set-top boxes, then for stable and correct operation of the service, you need to configure the grouping of interfaces
In the menu on the left Advanced settings -> Layer 2 interface -> WAN service and click the "Add" button

The selected interface must be set to eth3/eth3. In the WAN service configuration selection window, you must select the type of WAN service - Bridging. The description of the service can be left unchanged. To apply the settings, click "Apply/Save".

Grouping interfaces

Interface grouping is performed in order to separate video traffic from other types of traffic in the client's local network. And also in order for the STB set-top box to dynamically receive an IP address from the provider's network, and not from the DHCP server of your router.
To group interfaces, go to the menu on the left Additional settings -> Grouping interfaces. To create, click the "Add" button. We set the parameters as indicated in the screenshot

The router is now configured to watch IP-TV. In the configuration above, the cable from the STB must be connected to LAN1 of the router. If the Client has 2 STBs, then two ports eth0 and eth1 must be combined into an IP-TV group. Accordingly, set-top boxes are connected to the LAN1 and LAN2 ports.

Became fixed: 4 519

router [email protected] 2804 v7 rev1 is a universal network equipment needed to connect end devices to the Internet and IP-TV via Ethernet cable, telephone line and wireless cellular communication via 3G/LTE modem.

And in this article, the setup of the Rostelecom fast 2804 v7 router is discussed in detail, as well as its main characteristics and the setup of the 3g modem.

By the way, the advantages of this router are that, at its relatively low cost, it supports almost all the functions necessary for an ordinary user: from setting up a print server to the possibility of reserving the main Internet channel.

Sagemcom [email protected] 2804 v7: Features

In addition to the standard possibilities for distributing Internet traffic and IP-TV between several functional nodes of the local network, the router [email protected] 2804 also supports additional features such as:

• - creation of a backup Internet channel (in case of a power outage or problems on the side of the main communication provider);
• - the ability to use the router as a print server (for connecting several user devices to a network printer);
• - the possibility of using [email protected] 2804 as a network drive (in other words, when connected to a hard drive router, it can be "used" as a miniature server).

On the front panel of the sadgemcom fast 2804 there is a block of indicators of the router:

1. Power indicator. The normal operation of the modem is indicated by the constant green color of the Power indicator.

If this LED is red, then the fast 2804 modem is in emergency recovery mode, which starts when the router software is slightly damaged.

2. DSL indicator, which with a constant green light notifies the user of a normal ADSL connection, and with frequent blinking, the establishment of this connection.

3. Internet indicator, which should be solid green if the connection through the Internet account is successful.

4. WLAN indicator, which lights up green when the wifi module is activated on the router.

5. Several ETH indicators that glow when external devices are connected to the corresponding Ethernet port via a network cable.

6. WPS indicator, green indicates successful connection to the user device via .

7. USB indicator indicating successful connection of external media to sagemcom fst 2804 v7.

On the back of the fast 2804 v7 rev1 are:

One ADSL port for connecting to the Internet via a telephone line;

4 LAN ports (for connecting to a router via twisted pair);

A small hole with a Reset button recessed in the case (to reset the router to factory settings, you must press this button with a paper clip or a needle and hold it for 10 - 15 seconds);

Power connector (to which the sagemcom f st 2804 v7 power supply is connected);

Power button;

On the right side panel of sajack fast 2804 are located:

Connecting sagemcom f st 2804 v7

When connecting to the Internet via an ADSL telephone line, the cable provided by the provider should be connected to the splitter input (LINE), and the telephone set and router should be connected to its PHONE and MODEM outputs, respectively.

When connecting to the Internet using WAN Ethernet technology, the provider's network cable must be connected to the first LAN connector of the SajemCom 2804 router.

Modem Rostelecom f st 2804 v7: setup instructions

If the computer (on which the Rostelecom fast 2804 v7 router will be configured) is correctly connected to the router via twisted pair, then the following indication should be present on the router:

The first indicator is solid green;
- the second indicator - slowly blinking green;
- the fourth indicator - lights up or blinks green;
- one of the LAN ports is lit or blinking green.

The setup of the Rostelecom fast 2804 v7 router described in this manual corresponds to the initial setup of the device. If the router was previously in operation, it is recommended to first reset the device to factory settings using the Reset button.

Setting up a Sadgemcom 2804 router using the hardware setup wizard

To launch the fast 2804 router setup wizard, insert the disk supplied with the device into the computer's CD drive and follow the program's further instructions.

When the software installation is complete, the Setup Wizard will automatically start (which can also be launched from the Start menu -> Programs -> Hardware Setup Wizard).

In the process of automatically configuring the Rostelecom fast 2804 router, the following operations are performed:

• - updating the router software from the installation disk;
• - selection of the desired router configuration;
• - configuration of PPPoE connection and 3G redundancy;
• - diagnostics of equipment performance;
• - Installing the latest firmware version of the router from the update server.

Manual configuration of the router Rostelecom fast 2804 v7

In the absence of an installation disk, it is recommended to configure the Wi-Fi router [email protected] 2804 manually. To do this, in the address bar of any Internet browser installed on your computer, enter the combination of numbers 192.168.1.1 (the static ip address of the device indicated on the service label on the back of the sagemcom 2804) and press the "Enter" key.

It is recommended to change the default authentication data (login/password) to unique ones later to protect your router from unauthorized access.

Initially, you will be taken to the page of basic technical information about the device.

Modem Rostelecom [email protected] 2804 v7: Ethernet connection instruction

1. To configure the fast 2804 v7 modem by Rostelecom, in the left vertical menu, select the "Additional settings" section:

Here, first delete all connections created by default in the “Wan service” subsection;

In the "Layer 2 interface" tab, delete "DSL ATM";

Go to the "ETH interface" tab: select "eth0/eth0" in the drop-down list, set "VLAN/MUX mode" in the connection mode and click the "Apply/Save" button.

2. When all unnecessary settings are “cleaned up”, return to the “Wan service” tab again, click the “Add” button and select the “eth0 / eth0” port set in the previous step. Click Next.

3. In the next window, select the type of service "PPPoE" and write the value "-1" in the two lower lines. Click "Next"

4. At the next stage, in the "PPP username" and "PPP password" windows, enter the username and password for connecting to the Internet from your agreement with the provider. Click "Next"

5. If the new window contains the columns "Enable NAT" and "Enable Firewall", then put a marker in front of each of them. In subsequent windows (with the standard setup of the Rostelecom fast 2804 v7 router), nothing needs to be changed - click "Next" several times and at the end "Apply / Save" to make changes to the router settings.

How to set up a Rostelecom fast 2804 v7 router with an ADSL connection?

When connecting the Internet via a telephone line, after deleting the standard settings in the first step of the previous instruction, go to "Advanced settings", then "Layer 2 interface" and click the "Add" button.

• - in the VPI and VCI fields, enter the data from the contract with the provider (they can also be clarified in technical support) and click "Next";
• - go to "WAN service", click "Add" and select the interface according to the data entered in the previous window. Click next.
• - in "WAN Settings" select the type "router" and click "Next" again
• - enter the login, password and PPPoE service name from the Internet connection agreement;
• - set the marker on the fields "retry PPP on authentication failure" and "Enable IGMP Multicast Proxy", then double-click "Next" and "Apply".

sagemcom f st 2804 v7: wifi setup

Go to the "WLAN Settings" menu section;
- check the boxes "Enable wireless communication" and "Enable multicast transmission over wireless network (WMF)";
- enter "SSID" (this is the name of your Wi-Fi access point) and click "Apply";

- go to the "Security" section;
- Optionally, you can disable the WPS option;
- select the type of authentication "WPA-PSK";
- enter the password for Wi-Fi;
- select WPA encryption "TKIP+AES";
- click "Apply" to save the new settings.

Fast 2804 v7 router: setting up a 3g modem

Below is a sample list of supported sagemcom fast 2804 v7 rev 1 3G USB modems
- HUAWEI: E220, E1550, E1552, E1752, E160G, E176G, E180, E169G, E150, HW601
- ZTE: MF112, MF626, MF627, MF180, MF190A
- Alcatel: X220, X080
- Airplus: MCD-650
- Withtel: WMU-100A
- Anydata: ADU-300
- Yota: LU156 (LTE)

To set up a 3g modem on a fast 2804 v7 router:

Connect the device to a special USB connector on the side panel of the router;

Go to the "3G Configuration" section of the web interface and set the marker to "Enable 3G reservation";

With these settings, when the main (ADSL or Ethernet) Internet connection is disconnected, the router will automatically switch to the 3G/LTE channel.