How to remove the legrand socket from the wall. How to remove an outlet from a wall

If you want the wallpaper to look beautiful on the wall, then before pasting the surface, all sockets and switches are removed from it. No jewelry precision will help to get around the fixtures without removing them - the wallpaper around the perimeter will be uneven, and after the repair there will be an aftertaste with bitterness.

Below is a brief instruction with a photo, after spending 5 minutes on it, you will not get an electric shock, and the wallpaper will look beautiful in the interior of the apartment.

Step one - preparation

Sockets / switches are removed immediately before wallpapering, it is not necessary to do this in advance, as you can get an electric shock when you turn on the light or, alternatively, sit in the dark and turn off electrical appliances.

Take off old wallpaper
Prepare the wall (if necessary),
Glue is being prepared and new wallpaper is being cut,
Turn off the light on the counter
Remove sockets,
Glue wallpaper.

So you can avoid some inconvenience and the use of swear words when you are closely acquainted with the discovery of Alexander Volt.

From the tool you will need a flat and Phillips screwdriver.

Step two - remove the switch

As a reminder, we remove, not dismantle, sockets and switches, so it is important to keep them intact if replacement is not planned. Using the one-button model of the Legrand Etika switch as an example, the essence remains unchanged for other mechanisms.

First, remove the button, for which we use a flat screwdriver or a sharp knife. We put the screwdriver into the gap between the button and the switch frame, pressing the pressure panel until the fastening antennae comes out of the side hole. Do not overdo it - you need to press the button until the antennae comes out - no more, no less.

Now we remove the protective panel, which gives access to the wires and the main fasteners of the switch. To do this, unscrew 1-2 screws from the top and bottom and hook the protection with a screwdriver. The protective panel presses the switch frame against the wall, after removing the first one, the second one is automatically released and removed.

If the switch or socket has been standing for a long time and began to stagger, then at this stage the mechanism is fixed. To do this, after removing the protective panel and frame, clamp the two main fastening screws. They are located on the sides of the push mechanism in the switch or to the right and left of the plug in the socket. Tighten the screws sparing no effort - it is difficult to rip them off.

It is not necessary to completely remove the light switch mechanism– just remove the button, the protective panel and the front frame!

Now it remains to glue the wallpaper, cutting off the wallpaper sheets on the switch so that they go inside the perimeter of the switch by 1 cm, and install the mechanism back in the reverse order - the outer frame, fasten the protective panel with two screws and install the button until it clicks.

If you remove but do not change the switches, wash the button and top panel with soap and water after removal. Even with a good housewife, the switches become dirty over time, and it is impossible to thoroughly wash them on the wall.
If the walls for removing old wallpaper were not wetted and there are no small children at home, then do not turn off the light when removing switches and sockets - do this immediately before pasting, when wet sheets become a current conductor.

Light switches usually have a significant operating margin, so they do not have to be dismantled regularly.

However, if such a need has nevertheless come, then this should be done very carefully, and strictly following the sequence, so as not to damage the insides of the device, which are almost 90% plastic.

The first thing you should always do is, of course, turn off the electricity and only then start work. You will need these tools:

screwdriver - flat and cross-shaped;
screwdriver - voltage indicator;
portable light source.

Using a flat screwdriver, it is necessary to remove the switch keys, for which we install it with a tip between the frame and one of the keys, from the top or bottom side.

With a little effort and using a screwdriver as a lever, you need to pry off the key, and using your fingers to remove it from the grooves. The second key is removed already without the help of a screwdriver.

Using the indicator, they make sure that there is no voltage; for this, a screwdriver is necessarily applied to each of the contacts. If the switch is located in a dark place, use a light source to avoid damaging the equipment.

After removing the keys with the switch, you can perform any operation, and even under voltage, of course, observing the necessary precautions. They check the integrity of the contacts and the presence of voltage on them, after which they conclude that the device is working.

When there is a need to dismantle the switch, for a more detailed inspection with disconnection from the mains, or there is full confidence that the device needs to be replaced, then it is necessary to remove not only the keys, but also the fixing frame, which in turn holds the decorative frame.

To do this, you will need the same set of tools as in the previous case, however, if the switch is fixed with Phillips screws, then you will also need a Phillips screwdriver.

The fixing frame is located immediately below the keys, and you can remove it using the same flat screwdriver.

It is held with latches on the switch body, so you need to pry the teeth with a screwdriver without any extra effort, since the frame is quite fragile, and pull it towards you with your fingers. At the same time, it is necessary to hold the frame, because without the frame it can easily fall down.

Now, quite often you can find a universal wiring structure - a socket and a switch in one housing. This is very convenient, as it allows you to power the socket from one incoming line, and immediately connect the lighting fixtures by passing the phase wire through the switch.

In the event of a breakdown, which, however, is extremely rare, the entire body is removed completely, but this is not very difficult, however, it is necessary to know some features when removing such a structure.

Despite the fact that it is quite simple, in addition to the screw that fixes the case near the socket connectors, the fixation is also made in the area of the switch, under the key.

The first thing to do is to remove the switch key by prying it with a flat screwdriver, and then unscrew the screws holding the case under it, as well as the screw on the socket.

It is enough to easily pull the case towards you, and then inspect the socket and switch to find out the causes of the breakdown or even dismantle the device.

Wall-mounted tees are used to connect up to three electrical appliances to the network at the same time, without using additional network filters. Such an outlet is a stacked structure of three conventional single power points that have one drive.

To make the triple outlet look more aesthetically pleasing on the wall, its final element is a common outer frame that combines all three devices in one composition.

How to dismantle a triple socket on a wall

Before proceeding with the above process, you need to prepare a few tools:

screwdriver with a plastic handle;
insulating tape;
rubber gloves and rubber-soled shoes for working with electricity (in case you decide to work under voltage).

Note! If you have no experience with live electrical appliances, it's best not to start. Safety regulations prohibit even experienced electricians from doing this. If you do not have the gift of immortality, it is still better to turn off the electricity for a short period of dismantling the outlet.

The process of dismantling a triple socket consists of several step-by-step activities:

Preparatory work
Detachment of fixing stops
Disconnecting the device from the cable

Let's take a closer look at each of the above steps.

Step 1. Preparatory work

Before proceeding with the dismantling of the triple socket in the living room, you need to turn off the mains voltage in the entire apartment. Then it is worth several times to check the absence of voltage with an indicator, and only after that proceed with dismantling work.

Step 2: Removing the Mounting Screw

First you need to detach the top cover of the socket to gain access to the fixing screw, then use a screwdriver to unscrew it. After that, you can completely remove the top cover of the outlet, thereby gaining access to the "insides" of the electrical device.

Step 3: Detach the Mounting Stops

The socket is kept inside the box with the help of special fixing stops. They must be loosened by unscrewing the adjusting bolts. Now the body of the point can be easily pulled out of the socket.

Switches designed to switch the operating modes of lighting in rooms are distinguished by a high margin of safety. Therefore, they can last a very, very long time. However, sometimes there are situations when it is required to remove this element from the wall, for example, for wallpapering or replacing it with a new and improved model. The whole process will take on the strength of 20 minutes, even for a person who has encountered such a need for the first time. The main thing here is to adhere to safety rules, as well as perform all actions very carefully and carefully. After all, the switch is 90% made of plastic elements, which can be easily damaged if handled ineptly.

We remove the switch from the wall - what to look for first

To begin with, take care of the presence of special thin rubber gloves, without which it is not recommended to work. After that, you can proceed directly to the dismantling process. To properly remove the switch from the wall, you need to understand some of the features of the process.

Important points to highlight are:

Safety machines. The network is connected to the apartment through fuse plugs or current protection circuit breakers. Before starting work, it is mandatory to turn off the voltage, for which the toggle switch of the machine is moved to the lower position. If there are plugs in the switchboard, then you will need to turn them off by pressing the red button located nearby, and also unscrew both plugs from the cartridge, which are responsible for the neutral wire and phase.
Switch type. This is also a very important point. Today, a wide variety of models are used, which differ in additional functions - remote control, smooth adjustment, and so on. However, for our problem, only the type of fastening matters - hidden (the switch box is recessed into concrete) and external (the box is screwed to the wall with screws). The first type is somewhat more complicated, so we will focus on it.
Connection diagram. Most often, the light switch is equipped with several keys, which makes it difficult to remove the device from the wall, since the number of wires suitable for each key increases. In addition, the more keys, the longer it will take to remove each of these elements.

Remove the keys from the switch - the first stage of dismantling

Although the process of removing the switch is not difficult, it is recommended to try to invite an electrician. After all, work can be dangerous, because you have to deal with electricity. If calling a specialist is not possible, you have to act on your own. Before performing, you need to make sure that it is he who is out of order. Often the problem is in the cartridge, which simply burns out over time.

If the switch needs to be dismantled in any case, for example, to wallpaper the walls when this element interferes with work, then it will be necessary to completely de-energize the circuit for connecting electrical appliances in the apartment. Neglect of electrical safety rules can cause the following problems:

1. Fire
2. Breakdown of electrical wiring insulation
3. Failure of devices connected to the network as a result of a short circuit
4. Electric shock, eye damage, burns.

It is necessary not only to turn off the power in the apartment, but also to close the shield with a lock. You can also hang a sign on the shield, indicating that work is currently underway involving electricity. Only then can you be sure that none of the residents will accidentally supply current to the apartment.

To remove the switch, we need the following tools:

Portable light source
Voltage indicator screwdriver
Flat and Phillips screwdriver

We need a flat screwdriver to detach the keys. This must be done carefully so as not to scratch the keys and the frame, and also not to break them. The tip is installed between the frame and the key, on either side. Next, you need to apply a little effort, using a screwdriver as a lever, enough for the key to move away from its place. The remaining keys, if any, are removed much easier, already without the use of screwdrivers.

Now let's check if there is really no voltage. Here we need an indicator screwdriver, which we apply to each of the contacts. Suitable for keys. It is recommended to install a flashlight or any other light source so that you can see exactly what you are doing or touching. Therefore, it is better for beginners not to do such work on their own, it can be very difficult to do without help.

By removing the keys, the master gets the opportunity to check the integrity of the contacts, as well as determine the voltage in them. This will allow you to answer the question of whether the switch is out of order and whether it needs to be completely replaced. If further dismantling is necessary, we proceed to the next stage of work.

How to remove a frame - an algorithm of actions for beginners

It may be necessary to remove the switch from the wall in cases where it is necessary to completely replace the device, as well as to make a detailed inspection of the equipment. In this case, it will not be possible to limit yourself to just the keys, you also need to remove the frame in addition. Fortunately, this process is also not particularly difficult, the main thing is to act in accordance with the instructions and safety precautions.

We need the same set of tools as for working with keys. More often, the switch itself is fixed with several screws, for unscrewing which a Phillips screwdriver is useful. By unscrewing the screws, you can remove the frame. It is very fragile and thin, so the actions are performed as carefully as possible. Again, with a flat screwdriver, you need to pry off the frame, and then pull your fingers towards you. If everything is done correctly, the fixing frame will easily move away, after which you just have to get the light switch.

Socket with a switch - features of dismantling this device

Universal designs are very popular, including a socket and a switch, made in a single housing. Such devices are quite convenient during operation, since it becomes possible to connect lighting fixtures and power the outlet from one incoming line. The disadvantage is obvious - in the event of a breakdown of one of the elements, you will need to remove the socket from the wall along with the switch, regardless of the source of the problem. You should not worry, because this operation is performed very quickly.

Armed with a flat screwdriver, remove the keys, as described above. Under the keys are screws, which are removed with a Phillips screwdriver. This is not the only fastener element - the socket has its own screws, which will also need to be unscrewed to dismantle the entire case. Having unscrewed all the screws, it remains only to gently pull the body of the device towards you so that it moves away from its place. To help yourself, you can again use a flathead screwdriver, carefully prying off the case.

In cases where the source of lighting problems is the switch, you will need to replace it with a new one. When you go to a hardware store, be sure to take your old switch with you. This will ensure that the new model will fit the existing connector in size. By the way, if you previously had a keyboard instrument, this does not mean that you only need to buy the same equipment. So, a touch switch, or a switch with smooth light control, is perfect.

Connecting a new switch is done in the opposite order to dismantling the old one. The apartment, of course, is completely de-energized, after which the device itself is disassembled directly. Next, the wires are connected, this must be done in the same places where they were connected on the old switch. After that, the block is installed in the socket opening, fixed with four screws.

It remains only to fix the decorative frame and keys. This work can be considered fully completed. By turning on the switch in the switchboard, we make sure that everything works with a bang.

Most often, the need to disassemble the light switch occurs when it fails. Although the design of the product is quite simple, sometimes manufacturers (mainly Legrand, Schneider, Viko) make the dismantling holes invisible in order to improve the design. The result can be accidental damage to the case or a long search time for clips and connectors. So that readers of "" do not encounter such an absurd situation, we recommend that you view the detailed instructions for disassembling the case with your own hands.

So, in the initial position, you have a key switch securely fixed inside the strobe. To get started, prepare a tool in order to quickly disassemble the case - an indicator screwdriver, which will be enough.

The instructions for disassembling the light switch in the apartment are as follows:

Turn off the machine that protects the electrical wiring from network overloads and short circuits.
Verify that there is no electricity in the room using an indicator screwdriver.
Remove the key(s). It doesn't matter which one you use: single-key, double-key or three-key. To remove the key, you need to squeeze it with your fingers on the sides (in the middle) and carefully remove it from the case (as shown in the photo). Sometimes the part firmly "sits" inside the case and in order to get it, you need to pry off one of the edges with a screwdriver.
Remove the decorative frame. In some cases, the frame is fixed with two bolts from the inside, less often the part is held by grooves, which you need to lightly press with a screwdriver to disassemble the electrical accessories. Another option for fixing the frame is with the help of an additional element that is attached to the grooves of the caliper.
Remove the "core" from the socket. On the sides of the case there are two screws that secure the mechanism to the wall. All you need to do is unscrew them with a screwdriver. There is another option for holding the case in the socket - with bursting paws. They need to be loosened by unscrewing the bolts on the sides that regulate the angle of expansion.
Disconnect lead wires. Phase, ground and zero can be fixed with self-clamping terminals or screw clamps. In the first case, you just need to press the locking levers and pull the wires from the connectors. Screw terminals must be unscrewed with a screwdriver and carefully remove the wires.