How to make a brazier from discs with your own hands. How to make a brazier from a car disk

Very little is left before the summer season, and land owners will spend a lot of time on them. Food cooked outdoors is much tastier. Therefore, in this article we will consider how you can make a structure for a barbecue from old car rims with your own hands. Such a structure has great advantages, which can be used for a long time as a barbecue.

It should also be noted that such equipment will be safe and very convenient. Manufacturing should not cause complications, so everyone can handle the task. On it you can simply cook not only a barbecue, but also install a cauldron.

How to make a brazier from car rims (Zhiguli or ZIL)

For the manufacture of a metal barbecue, it is recommended to use old rims from a Zhiguli car. However, they should not be made of aluminum alloy, but of solid steel. If you don’t have discs in your garage, then you can contact any tire service. If they are not given away for free, then you need to pay a symbolic amount.

For the manufacture of the structure, it is necessary to prepare the following tools and materials:

• 1 m of wire with a diameter of 8 mm.
• 3 bolts with nuts.
• 4 nuts with a diameter of 10 mm.
• Profile metal pipe with a length of at least 1 m.
• Two car rims of the same size.
• Welding machine.
• Bulgarian.

Cut a baffle on one of the disks. To do this, you can make notches with a grinder, and then break it out with a heavy hammer. If there is a gas cutter, then it is more convenient to use it.

Then the disks need to be welded to each other around the perimeter with a welding machine. Thus, the partition of the second disk will serve as the bottom of the metal container.

To use the barbecue for cooking in a cauldron, you need to make a small door. In this case, you do not need to remove the dish to add wood fuel. This manufacturing step is the most difficult.

To do this, it is necessary to mark a rectangle, the lower part of which should be at a height of several centimeters from the bottom. In the middle of the door there will be a seam left by the welding machine.

Cut out a rectangle with a grinder, and then process all the edges to get rid of burrs. From this side, weld the heads of the bolts. Weld nuts on the cut out part. Thus, we made homemade loops. On the other side of the cut out fragment, you need to make a hole and screw in the bolt. It will act as a handle.

At the next stage, you need to weld the bottom of the future barbecue with a metal sheet so that the coals do not fall. Only need to leave small holes to increase traction. Some experts recommend installing a thick wire mesh at the bottom.

After that, prepare 3 profile pipes, up to 80 cm high. However, this is all individual, since it all depends on the height of the person who will be cooking. Weld metal pipes to the bottom of the structure at equal distances. As a result, the brazier will stand securely on the surface.

For safety and comfortable use of the design, you need to make handles. To do this, you need to visually divide the disk in half, and on opposite sides, a few centimeters from the top, you need to weld two nuts each. Then thread the bent wire into them.

To improve the appearance of the manufactured brazier, it must be calcined, and then coated with dark heat-resistant paint. The design is quite light and mobile, so you can take it with you not only to your summer cottage, but also to outdoor recreation.

Drawing, photo and video of a brazier from discs for self-production

Since the old rims have the same dimensions, the development of a diagram or drawing is not required. Everything is quite simple, as could be understood from the above instructions for manufacturing the structure. You just need to decide on the height of the legs so that it is comfortable to cook.

Below from the video you can learn how to make a metal grill from one car disk. All work takes no more than one hour, subject to the availability of the necessary materials and a welding machine.

If you show creative imagination, you can make a beautiful and functional brazier. The photo shows the results of the masters.

A design such as a brazier made of car wheels is an excellent option for reusing waste materials. Such a device is simple in execution, and therefore it can be done by hand. Despite the simplest design, there are enough ways to use the product, it can even replace a complex barbecue model.

An example of a brazier made from old car rims

Design features

A self-made brazier from a wheel disk has a lot of positive characteristics. This design allows you to acquire a full-fledged grill complex with minimal costs for its manufacture. All materials are quite affordable for almost any summer resident. In addition, they guarantee the durability of the product and its strength under any operating conditions. Another plus is the compactness of the brazier. It is worth talking about its distinctive features and options in more detail.

Video: instructions for making a brazier from rims

Materials used

In order to make a brazier from disks, it will not be necessary to spend a lot of money, since practically improvised materials are used for its manufacture. Already exhausted car disks are usually thrown away or given away for a penny for scrap. This does not take into account the many ways of their alternative use, among which the manufacture of barbecue is one of the best options.

Unnecessary car rims get a chance for a second life

For a summer residence or a private house, a brazier is considered a mandatory attribute. Making from old disks saves money, since ready-made models are often inferior to this option in terms of their capabilities in relation to cost.

Please note: almost every motorist has at least one unnecessary old wheel. Otherwise, you can find suitable material from friends, garage neighbors, or buy it for a small amount at a service station or from your hands.

The advantage of using discs to create a grill is the thickness of the metal. Even worn out wheels will be suitable for this kind of further operation. The metal will not fade or deform, and their shape is ideal for creating complex charcoal products.

Principle of operation

According to the principle of operation, the brazier from rims is similar to some other home-made models, for example, made from a barrel or a cylinder. It combines the following features:

• grill - allows you to cook on skewers or a removable grill;
• barbecue - for frying steaks, complemented by a lid that creates the effect of an oven;
• hob - the shape and diameter of the disk allows you to put a boiler, pan or pan on fire;
• smokehouse - some models allow hot smoking of products.

Simple-looking design combines all the necessary functions

The principle of operation is extremely simple. Firewood or ready-made coals are loaded into the lower part. A grate is installed on top or skewers are stacked. The dishes can also be placed on the grate or directly on the wheel if their diameter is compatible. The heat from below warms the air and allows you to cook like on a regular grill. For smoking, you need to close the top exit and ensure that the wood chips smolder so that smoke forms.

Each design is thought out individually, adjusted to the needs of the owners. However, the main part of the work on the manufacture of the product remains common to all models.

Versions

In more detail, you need to consider possible options for the execution of the product. If you want to make a brazier from car rims, you need to pay attention to the following models:

The simplest option is a brazier for skewers

• Double construction. 2 wheels are used, thanks to which the brazier becomes higher. Due to this, you can put a cauldron on top. Heating from all sides allows you to cook delicious dishes in it, like in the oven or stew them.
• closed oven. Allows you to smoke products, as the smoke is collected inside the chamber and is removed in a small amount through special openings.
• complex models. It combines all 4 functions of the product described earlier. Additionally, other useful elements can be mounted, for example, a chimney.

Advanced models with a grill grate and auxiliary elements

It is also worth noting that such a brazier can be made with legs and without legs. The stand will be needed for single models, but in double and triple models, its function is performed by the lower disk. At the same time, there are restrictions regarding the use of the structure, because damp ground can prevent the formation of heat, and hot metal is not allowed to come into contact with the wooden floor on the terrace.

Readers find these materials useful:

• How to build your own barbecue complex?
• Garden barbecues as an element of cooking and a whole philosophy

In order to independently make a brazier from auto disks, it is necessary to think over the scheme of the future product in advance. Decide on the amount of consumables, prepare the tools. To perform high-quality work, it is necessary to have the skills to use a grinder for cutting metal, as well as a welding machine.

Preparation of materials and necessary tools

In order to make a brazier from rims with your own hands, you will need the following materials and tools:

• old auto disks;
• Bulgarian;
• nozzle for cutting metal;
• rust cleaning disc in the form of an iron brush;
• file;
• drill;
• a hammer;
• bolts;
• profiled pipes or steel bar;
• grill grate.

Bulgarian and welding machine - the main tools when working with metal

All these tools will be needed to process and connect the details of the brazier. It is convenient to make legs from profiled pipes and rod. In total they will need 3-4 pieces.

Tip: it is better to make 4 supports for greater stability of the product. The tripod may tip over to one side when placed on an uneven surface.

Old discs should preferably be cleaned of rust in advance.

The wheels themselves need to be prepared in advance. If there are traces of rust and paint, the surface is cleaned with a metal brush using a grinder or drill. All excess is cut off.

Easy option

Several options for the manufacture of such grill structures should be considered. You need to start with the simplest - a single brazier from a wheel disc with legs. In order to make it initially, you will need to carry out a series of manipulations with the disk itself:

1. On one side, the inner part is cut out - the partition. A container is formed, similar to a bowler hat.
2. If there are too many holes in the bottom or they are large enough for the coals to wake up through them, an additional plate must be welded on. You should not completely close the gaps, as the coals must be blown to maintain heat.
3. Legs are welded on the sides to the bottom or closer to the top. Usually they are made 40-45 cm in length. This height of the brazier is optimal, as it ensures the stability of the structure and ease of use.

Metal legs are welded to the back of the discs

Next, if necessary, you need to clean the sections so that there are no sharp edges left. You can optionally install a grille. It is not necessary to weld it, it is more profitable to use removable parts. Also, for the convenience of maintaining heat and cleaning out the ashes, you can make a window for firewood on the side of the disk. For transfer, the structure is equipped with handles, welding them symmetrically on the sides of the wheel.

The top is cut out for the installation of a barbecue grill

Tip: if you use two or three wheels, you can limit yourself to welding metal bars to the bottom. In some cases, you can do without supports at all.

Barbecue option without legs

Smoking chamber

It is more profitable to make such a brazier from car disks, which can be used in different directions. For lovers of homemade balyks and sausages, a smokehouse will become an indispensable tool. In order to turn old wheels into such a useful thing, you need to use at least two units of material.

The principle of operation is that you need to connect two disks into a single hollow structure. The top can be adapted for frying kebabs according to the principle of the previous model, but to save smoke, you need to take care of arranging the lid and the smoke extraction system. You can leave the partition with holes, which will simplify the task, and use the product as a hob.

In order to combine two disks, it is necessary to cut off the partitions. Next, the wheels are joined and welded with a continuous seam to each other. Legs are welded to the bottom of the lower element. To provide access inside, a door is equipped. To make it, you need to walk with a grinder approximately in the middle of the product and cut out a rectangle.

Horizontal welding seam runs through the center of the door

To fix the door, one nut is welded to it, symmetrically with respect to the weld. 1 bolt is also attached to the barbecue by welding so that the door nuts can be put on them.

The sash is fastened with bolts for welding

Tip: in order to fix the sash without any problems, the bolts are initially screwed into the already welded nuts. Then the door is applied to the opening and fixed already on the structure itself.

Such home-made barbecues allow you to equip all the conditions for relaxing with barbecue with minimal equipment costs. In addition, you don’t have to apply any extra effort, because all the stages of work are extremely understandable and easy to implement.

kamin-maker.com

Barbecue from car disks for shish kebab and for a cauldron. Do-it-yourself brazier from disks from A to Z

Very little is left before the summer season, and land owners will spend a lot of time on them. Food cooked outdoors is much tastier. Therefore, in this article we will consider how you can make a structure for a barbecue from old car rims with your own hands. Such a structure has great advantages, which can be used for a long time as a barbecue.

It should also be noted that such equipment will be safe and very convenient. Manufacturing should not cause complications, so everyone can handle the task. On it you can simply cook not only a barbecue, but also install a cauldron.

How to make a brazier from car rims (Zhiguli or ZIL)

For the manufacture of a metal barbecue, it is recommended to use old rims from a Zhiguli car. However, they should not be made of aluminum alloy, but of solid steel. If you don’t have discs in your garage, then you can contact any tire service. If they are not given away for free, then you need to pay a symbolic amount.

For the manufacture of the structure, it is necessary to prepare the following tools and materials:

• 1 m of wire with a diameter of 8 mm.
• 3 bolts with nuts.
• 4 nuts with a diameter of 10 mm.
• Profile metal pipe with a length of at least 1 m.
• Two car rims of the same size.
• Welding machine.
• Bulgarian.

Cut a baffle on one of the disks. To do this, you can make notches with a grinder, and then break it out with a heavy hammer. If there is a gas cutter, then it is more convenient to use it.

Then the disks need to be welded to each other around the perimeter with a welding machine. Thus, the partition of the second disk will serve as the bottom of the metal container.

To use the barbecue for cooking in a cauldron, you need to make a small door. In this case, you do not need to remove the dish to add wood fuel. This manufacturing step is the most difficult.

To do this, it is necessary to mark a rectangle, the lower part of which should be at a height of several centimeters from the bottom. In the middle of the door there will be a seam left by the welding machine.

Cut out a rectangle with a grinder, and then process all the edges to get rid of burrs. From this side, weld the heads of the bolts. Weld nuts on the cut out part. Thus, we made homemade loops. On the other side of the cut out fragment, you need to make a hole and screw in the bolt. It will act as a handle.

At the next stage, you need to weld the bottom of the future barbecue with a metal sheet so that the coals do not fall. Only need to leave small holes to increase traction. Some experts recommend installing a thick wire mesh at the bottom.

After that, prepare 3 profile pipes, up to 80 cm high. However, this is all individual, since it all depends on the height of the person who will be cooking. Weld metal pipes to the bottom of the structure at equal distances. As a result, the brazier will stand securely on the surface.

For safety and comfortable use of the design, you need to make handles. To do this, you need to visually divide the disk in half, and on opposite sides, a few centimeters from the top, you need to weld two nuts each. Then thread the bent wire into them.

To improve the appearance of the manufactured brazier, it must be calcined, and then coated with dark heat-resistant paint. The design is quite light and mobile, so you can take it with you not only to your summer cottage, but also to outdoor recreation.

Drawing, photo and video of a brazier from discs for self-production

Since the old rims have the same dimensions, the development of a diagram or drawing is not required. Everything is quite simple, as could be understood from the above instructions for manufacturing the structure. You just need to decide on the height of the legs so that it is comfortable to cook.

Below from the video you can learn how to make a metal grill from one car disk. All work takes no more than one hour, subject to the availability of the necessary materials and a welding machine.

If you show creative imagination, you can make a beautiful and functional brazier. The photo shows the results of the masters.

Summing up, we can say that the design for a cauldron or barbecue can be made in a short time. You only need to have a little experience with the welding machine.

leadinlife.info

Do-it-yourself disc brazier (25) barbecue grill ideas

25 original ideas for a brazier made from car discs made by hand.

The rims did not go unnoticed by our Kulibins, quick-witted craftsmen quickly found use for stamped steel rims.

As it turned out, you can make an excellent barbecue grill out of disks, while the homemade product looks very original, as you can see by viewing this selection of homemade barbecue grills from disks.

Let's start from the brazier with a lifting mechanism for the grate made from a car jack. The jack allows you to adjust the height of the grate above the coals.

Forged lattice under the cauldron.

Here the brazier is mounted on a car shock absorber and spring.

Barbecue with chimney.

The furnace from disks under a cauldron.

Openwork brazier from a disk with forging elements.

Barbecue with folding grill.

Barbecue oven with a spit.

Support legs can be welded directly to the disc.

Hanging barbecue grill from the disk.

Barbecue on wheels.

Another version of the brazier made from a disk from a truck.

In fact, for the manufacture of such a brazier, you will need 1 - 2 car disks, several metal rods or pipes, a welding machine and a grinder. Of course, here you will need the skills to work with a welding machine, in the presence of which it will not be difficult to make a barbecue grill.

(5 ratings, average: 4.80 out of 5) Loading...

sam-builder.com

How to make a barbecue from car rims?

It is difficult for car owners to part with old rims. And suddenly come in handy! And they lie in garages and cottages, and are waiting for their finest hour. And now he has arrived! There is a great idea to use rims under the barbecue. A specialist with golden hands will easily collect a useful thing for himself and enjoy the aroma of fried kebabs or pilaf on quiet summer evenings. The family is happy, money in the family budget is saved. And if the master also has a good imagination, then amazing masterpieces are obtained from the wheels.

To make a homemade brazier from discs, you do not need to go specially somewhere to the market and buy expensive materials. All car owners have wheels. You can go to any auto repair shop, the masters will gladly provide you with a pair of former wheels. It is worth noting the durability of the material and strength. You can hardly find a dent or scratch on the disc due to the thickness of the metal.

The shape of the discs is ideal for turning into a barbecue. Work on its manufacture takes just a couple of hours. Only improvised materials are used. The product is compact and can be easily moved. The design perfectly holds the heat of the fire, not inferior to products of well-known brands. Such a brazier can be used for other purposes. It will easily fit into the conditions of hunting or fishing, becoming a camp kitchen for a while. And here the assortment of dishes is different - fish soup, pilaf, stewed potatoes and much more.

The design of the firebox ensures the flow of air, which maintains the required temperature of the heat. Homemade barbecue is easy to clean after cooking. It does not burn through, withstanding the fire for several hours.

Even a child can figure out how the brazier works. Coals are laid in the lower level. A traditional grill grate and dishes are placed on top. You can do without it, fry traditional meat on skewers.

The heat comes from below, the cooking conditions are the same as on the usual grill. When smoking, it is necessary to close the top outlet. This will ensure the decay of wood and the formation of smoke. Each owner makes a brazier for himself, but the main work on its manufacture remains common.

With all the advantages, there are also disadvantages. One of them is the low height. Cooking is too low. The traction may not be enough, and the brazier may simply fade out. Another disadvantage is the small volume of the firebox. Many users compare the design possibilities with camping bricks, which are used as coasters for skewers. But this, of course, is not entirely true.

The world of homemade barbecues is diverse. Craftsmen turn barrels and cylinders into braziers.

Brazier from auto disks offers the following functionality:

• cooking on skewers shish kebab or grill;
• B-B-Q;
• cooking in a dish. A cauldron is commonly used;
• smokehouse.

For giving such a brazier is an ideal option.

There are several options for making barbecues. The simplest model is called a simple grill. There is nothing complicated here. Coals are laid in the wheel, and everything is optional on top: skewers with barbecue or meat on the grill.

More options for a double design. Due to the use of two wheels, the product becomes higher. A cauldron is placed on top. There is a uniform heating, which ensures extinguishing. Food can be smoked in a closed oven. The smoke remains inside the structure and is removed through a special outlet.

There are universal models. You can do everything on them: barbecue, dishes in a cauldron, smoking. Such a brazier can be with legs and without them. For a brazier from one disk the support is obligatory. Double and triple braziers may well do without it. The lower disc becomes the same stand. There are restrictions when using such a barbecue. If the earth is after rain or snow, then it will prevent the formation of heat. You can not put the barbecue on a wooden floor.

Before making a brazier, it is necessary to think over its scheme, what functions you need to get from it. After determining the number of disks, it is necessary to prepare the tools. You will need skills in owning a grinder and a welding machine.

Despite the ease of manufacture of the brazier, there are questions about the choice of discs. From which machine is best to use? Finding wheels is not a problem. Any tire shop will be happy to share their surplus auto disks. Experienced drivers believe that truck rims are best. The best option is considered to be wheels from the KAMAZ wheel. They are made of thick metal and will not burn out for up to 40 years. The same can be said about disks from any truck. But a disk, for example, from a minibus will last up to 20 years.

In principle, the wheels of any car are suitable for the role of a brazier. It is made from stamped car wheels. They are made from high quality steel. The service life of the brazier depends on the fuel. From coal, the product burns out faster.

The idea of ​​a brazier made of car wheels quickly spread throughout the country and many began to think about its implementation.

Before you start welding, you need to audit everything you need.

Prepare the following equipment and tools:

• rims;
• iron brush for cleaning rust;
• Bulgarian saw;
• welding machine;
• drill;
• a hammer;
• bolts;
• file;
• nozzle for cutting metal;
• steel bar (profile pipes are possible).

The latter will go on their legs under the barbecue. Four supports are recommended for stability. A tripod on an uneven surface may collapse. Rust must be removed from the discs. The surface should be processed with a Bulgarian saw. Installation is carried out by welding.

All work is carried out in compliance with safety regulations. Be sure to use personal protective equipment. When welding, the eyes should be covered with goggles or a mask, work should be performed only in special gloves. When working with a grinder, its disk must be kept at a right angle to the object. Otherwise, the disk may bite, and its fragments will fly. Work should be carried out only in special glasses.

It is worth starting with the simplest model - this is a single circle on a stand.

To create such a product, you must perform the following steps:

• cut out the inner wall. After that, the workpiece becomes like a barrel;
• there are discs with a large number of holes, then they must be closed;
• the plate should be brewed, but gaps should be left to purge the coals;
• on the sides of the bottom by welding it is necessary to fix the legs. Their optimal length is up to 45 cm;

• then you need to clean the sections. Make a window in the side part to monitor the fire and clean out the contents of the structure;
• the frying grid is best left removable;
• it remains only to weld the handles. This will add comfort during the operation of the barbecue.

Another do-it-yourself brazier option is a smokehouse. You will need two disks. This option can be considered universal. On it you can cook not only kebabs, but also grill, stew food.

The work is simple and includes the following steps:

• it is necessary to connect two parts into one;
• to keep the smoke, you need a cover and a removal system, so you need to leave a partition in the upper disk;
• the lower disk should be removed from the partition, using a welding machine, join both disks to each other;
• you need to weld the legs;
• in the middle of the lower disk, you need to make a door;
• upon completion of work, it is necessary to calcinate the structure. This will clean it of gasoline and oil;
• to give the product presentability, you need to cover it with a resistant thermal paint.

Before that, you need to remove the remnants of rust. This can be done with a stiff brush or with a special drill attachment. It will not be superfluous to walk again on the sides of the barbecue with sandpaper, then degrease and you can start painting.

You can come up with a lot of options with barbecues, especially in terms of design. All of them are original and always arouse interest. But how much sincere joy to others when they find out that the brazier is made with their own hands from ordinary disks.

Old auto parts can be a great solution for creating new, unique products. The idea with barbecues is very original, human thought develops it constantly. This can be a suspended structure, a mobile barbecue, a brazier with a grill lifted with a jack, a structure with a skewer. These are all portable models.

There is a hearth on the covered veranda. The brazier is installed on a brick stand in the very center of the room. To provide air blowing, an empty space is left under the hearth body. The brazier is covered with bricks. A round table is set around it, benches are set up. It turned out to be a hearth around which you can sit and warm yourself. Created a cozy atmosphere for enjoying delicious food. In winter, you can drink tea here, inhaling the aromas of fried food.

You can overlay the brazier with any material. Such a gazebo will become a favorite place to meet family or get-togethers with friends.

It is worth noting that after the rims were tested by the barbecue, they began to look for other applications. For example, as a stove for a bathhouse or a potbelly stove for a home. The designers went further and offered to decorate the apartments with plafonds from discs. There is even a stylish solution to use discs as bar stools and wash basins. Do not throw away the obsolete, but look at old things in a new way. It's time to do some tuning on old car rims!

How to make a brazier from car rims, see the video below.

www.stroy-podskazka.ru

Self-assembly of a brazier from discs from car wheels is a very cheap way to purchase a useful and functional thing that is needed in the garden. It is no secret that during the summer season, residents of megacities vacationing outside the city find themselves in an environment devoid of their usual comfort. Instead of convenient stoves and multicookers, you have to adapt to electric stoves with 1-2 burners. In the event of a sudden power outage in a holiday village, a primitive period begins. You can solve the problem of the inconvenience of cooking on a fire with the help of an ingenious device developed by craftsmen.

It is very easy for car owners to get 1-2 rims. Although these parts do not change as often as tires or tubes, you can find some barbecue material in the garage. Waste wheels are thrown into landfills or handed over to scrap metal collection points. A lightweight structure on a metal site can be bought for a purely symbolic amount.

In addition to the disks themselves, you will need:

For painting the portable version, you need to pick up heat-resistant paint. Staining will give the structure an aesthetic appearance and protect it from the effects of precipitation when stored outdoors.

The easiest way to make a brazier from rims is to lay the spare part open side up. Regular holes in the cap will serve as a grate for the fuel placed inside. This design can be supplemented with handles and taken with you on picnics: it is light and practically does not take up space in the trunk, but it can reliably prevent forest fires, preventing the coals from scattering, and limiting the fire to the diameter of the rim. Here is a video instruction for you right away, how to do it quickly and what you need to pay attention to when working:

How to make a Finnish hearth from rims from a car?

A distinctive feature of this type of stove is an open hearth installed in the center of the table. It does not take a lot of time and materials to make it. A round metal firebox can be successfully replaced by a rim raised to the desired height. The base for it can be made of stone, cinder block or bricks, remembering to leave free space for air to flow into the furnace.

Install the disk from the machine on the prepared base and surround it around the circumference with wild stone or brick, leaving a small hole at the very bottom for blowing. The height of the masonry should be such as to completely hide the base and the metal hearth. You can slightly improve the design by welding a pin with a hook on the side for hanging a teapot or pot.

On the resulting low column with a recess on top, you need to lay a round tabletop. This can be a saw cut of a large tree, a specially made slab of artificial stone, a sheet of thick metal, or another accessible item. There should be a hole in the center of the tabletop, the diameter of which matches the size of the rim.

Such a brazier from car disks is stationary. Around it you can arrange circular seats. To protect from rain, it is best to build a light canopy, and if desired, the master can build a warm gazebo.

Portable brazier of complex design from auto disks

A metal brazier made of car rims, made by a master with imagination, can serve as a source of his pride. With all the simplicity of the design, such a stove is a multifunctional device: it is a grill or barbecue, and a convenient stand for a cauldron, and decorating a recreation area in the garden. In the photo you can see the design of the miracle stove with forged elements, and the fire-breathing Darth Vader.

Such a hearth is not very heavy, so it can be installed in any convenient place on the site or taken with you to nature. A design feature is the use of 2 identical discs from the wheels of a passenger car at once. The material must first be prepared for work: cut or cut out the middle of one of them so that only the rim remains.

Install the disks from the machine in this order:

• place the whole one below, laying it with the cap down;
• install the one from which the central part was removed from above.

The upper part of the structure must be positioned so that the rib remaining after the removal of the cap is located on top, creating a partial overlap of the roof of the firebox. It is on it that it will be possible to lay the grill grate or put a cauldron and a kettle. The sides from the top of the rim will hold the cauldron in position.

Weld the upper and lower parts of the brazier around the circumference. So that during the operation of the product you do not have to remove the dishes installed above the fire every time, you need to cut a door in the side of the oven. Mark and cut out a rectangle of a convenient size so that a sill about 10 cm high remains above the grate (bottom of the furnace). This will allow the coals not to fall out when the door is opened.
The remaining parameters of the hole can be arbitrary. In principle, everything can be seen in the provided photos.

The cut piece must be provided with loops on one side and a valve on the opposite side. For these purposes, you can use ordinary metal fittings (latches, hooks, door hinges, etc.). You can attach small parts using a welding machine or bolts with nuts.

In order to raise the brazier to a height convenient for cooking, 3-4 legs must be welded from below from pieces of a corner or professional pipe. These parts are most conveniently placed inside the rim, the slope of the walls of which will give the structure elegance and stability, ensuring the divergence of the lower part of the supports. If desired, the master can solve the problem in another way, by welding a single leg in the center of the structure and supplementing it with a wide and heavy base.

Here is another idea how you can do everything without using welding:

After burning out the remnants of the old paint and applying a heat-resistant coating, the braziers can be considered ready for use. If desired, you can supplement the design with supports for laying skewers over the neck of the brazier, handles for easy carrying and other necessary little things.

Self-made hearths of different types will simplify the process of cooking on an open fire. Each option can become the heart of a friendly company in nature, and in the garden, and in the gazebo. The relatively safe design of portable models requires their installation on non-combustible materials if the floor in the recreation area is wooden. Especially for this, you can lay out the hearth zone with bricks or paving slabs.

Many have used rims lying around in the garage or in the country. They have already worked out their service life, and it is a pity to throw it away, as always.

They can be used - to cook a stationary or portable, convenient and safe barbecue. From analogs, the brazier from automobile disks differs in compactness, stability and accurate appearance.

Its production will require a minimum of time and even less material costs. Such a brazier can be a hearth for a Finnish gazebo and an excellent camping stove.

On it you can cook not only the usual barbecue on a skewer, but also barbecue dishes, as well as install a pot or a cauldron.

The presence of a stationary hearth in a summer cottage will allow you to please yourself and loved ones with delicacies cooked on an open fire much more often.

The design of the furnace provides excellent air access, which greatly simplifies maintaining the required temperature. Convenient height and the ability to install anywhere will add comfort to parties.

Such a brazier is easy to clean, does not burn out, takes up a minimum of storage space.

On the photo is a brazier from car disks

Like any device that is made by craftsmen with their own hands, the brazier from car disks has many different options.

The simplest of them does not require additional materials. It is enough just to cover the bottom hole with a sheet of metal or even ordinary ceramic tiles.

But, such a model, although simple to manufacture, has a number of disadvantages:

• the plane on which food is cooked is too low;
• such a brazier installed on the ground may fade due to lack of traction;
• small furnace volume.

In general, cooking on such a model, in terms of convenience, does not differ from the hiking option, when simple bricks are used as a skewer stand.

Tools and materials

If, however, you want a reliable and convenient barbecue that will turn any picnic or party in the country into a pleasure for many years, then you should consider a more complex design of two wheels.

Before work, you need to prepare tools and stock up on materials. For a barbecue from car disks, you will need:

• angle grinder (grinder);
• welding machine and electrodes;
• personal protective equipment (gloves, mask);
• two identical disks;
• profile pipe about a meter;
• three bolts and nuts to them of large diameter;
• 4 nuts 10mm;
• Wire meter 8 mm.

All materials can be redeemed for a penny at any recycling center, but most household summer residents can find them in the garage.

Work order

How to make a barbecue from car rims so that it lasts a long time?

Foundation preparation

In one of the disks it is necessary to cut a partition. This can be done with a gas cutter or, having made notches with a grinder, simply break it out with a hammer.

After that, two disks must be welded to each other around the entire perimeter. The result should be a metal container in which the remaining partition will be the bottom.

Door manufacturing

One of the most difficult stages is the manufacture of the door. Its presence will allow you to cook dishes in a cauldron without violating the temperature regime. With it, you can throw firewood without removing the dish from the grill.

To make everything work out neatly, mark a rectangle in the middle of which the weld will pass. The bottom side of the door should be a few centimeters above the bottom partition.

Cut out the marked rectangle. The edges must be processed so that there are no sharp edges and burrs. After that, you need to grab the bolt heads to one of the vertical sides.

Closer to the opposite edge, at a distance of several centimeters, a hole is drilled into which the third bolt is screwed so that it looks out 4-5 cm from the outside. It will become the door handle.

Nuts are screwed onto the welded bolts, which, having put the cut-out fragment in place, are grabbed to the body.

The metal door on improvised hinges is ready.

Legs - the basis of the product

It remains to make the legs and close the hole in the bottom. The legs are made of such a height that it is convenient to cook. You can measure in each case individually. But, the optimal height from the ground to the top of the barbecue is 60-80 cm.

Having decided on the length of the legs, you need to cut off three equal pieces of the profile pipe. They, focusing on the factory holes in the partition of the lower disk, are welded at an equal distance.

The angle of inclination will be the same if they are rested against the partition and the side. It is recommended to make three legs, since this design has the greatest stability. Even on uneven ground, it will not swing.

Comfortable handles - safe and comfortable

For greater convenience, you can make grill handles from car disks.

To do this, turn the body so that the door is directly in front of you and mentally draw a line that will divide the circumference of the entire barbecue in half, put marks.

This will be the line that will have the middle of our handles.

From the mark, lower the perpendicular along the side wall of the case, at a distance from the upper edge of the disk, step back 5-7 cm to the right and left and put new marks.

4 nuts are welded on them. Handles bent from 8 mm wire are threaded into them.

It is better not to weld the bottom of the resulting brazier with metal. You can close it with a metal mesh or weld on pieces of thick wire, making a kind of grate. This will provide good traction.

Additional trivia

This completes the installation work. Now it remains to ennoble the grill. First of all, it is calcined so that the remains of oil, gasoline, garbage and other things burn out.

After that, the surface outside must be cleaned of soot and sanded. You can paint the brazier with heat-resistant paint, but it is better to choose a dark color. Black in this case does not look gloomy, but noble.

Applications

The described model is mobile. Such a brazier can be carried with you on hikes and simply transferred around the site to any place. It is light enough to be lifted by one person.

But, if desired, it can also be used in stationary buildings on a personal plot.

For example, this the simplest version of the hearth for the Finnish gazebo. A covered resting place with a hearth in the center of the table is becoming more and more popular in our country.

In this case, the body is installed on a brick pedestal. When calculating masonry, do not forget about the need to blow air for combustion. Therefore, an empty space is left under the furnace body. The entire brazier is lined almost to the top with brick or natural stone.

On the resulting pole, a tabletop with a hole in the center is installed. Benches are set up around the resulting table, and the whole ensemble is covered with a roof with a hood.

In such a Finnish gazebo, you can enjoy barbecue and fondue not only in summer, but also in the cold season. The fire from the hearth will not let you freeze.

Also, the brazier can simply be overlaid with facing materials and made the center of the resting place on your backyard. A metal firebox extends the service life of the hearth many times over and greatly facilitates its operation.

In addition, laying out the finished structure is much easier than laying out a full-fledged furnace.

The use of a brazier from car rims will allow you to create a comfortable and beautiful place for relaxing friendly parties, even for those who do not have special skills in the construction business.

A design such as a brazier made of car wheels is an excellent option for reusing waste materials. Such a device is simple in execution, and therefore it can be done by hand. Despite the simplest design, there are enough ways to use the product, it can even replace a complex barbecue model.

Design features

A self-made brazier from a wheel disk has a lot of positive characteristics. This design allows you to acquire a full-fledged grill complex with minimal costs for its manufacture. All materials are quite affordable for almost any summer resident. In addition, they guarantee the durability of the product and its strength under any operating conditions. Another plus is the compactness of the brazier. It is worth talking about its distinctive features and options in more detail.

Video: instructions for making a brazier from rims

Materials used

In order to make a brazier from disks, it will not be necessary to spend a lot of money, since practically improvised materials are used for its manufacture. Already exhausted car disks are usually thrown away or given away for a penny for scrap. This does not take into account the many ways of their alternative use, among which the manufacture of barbecue is one of the best options.

For a summer residence or a private house, a brazier is considered a mandatory attribute. Making from old disks saves money, since ready-made models are often inferior to this option in terms of their capabilities in relation to cost.

The onset of the cold season leads to the need for heating or creating simply comfortable microclimate parameters in garages or auxiliary buildings in living conditions outside the city. This problem becomes especially urgent in conditions of impossibility to carry out centralized heating.

Please note: almost every motorist has at least one unnecessary old wheel. Otherwise, you can find suitable material from friends, garage neighbors, or buy it for a small amount at a service station or from your hands.

The advantage of using discs to create a grill is the thickness of the metal. Even worn out wheels will be suitable for this kind of further operation. The metal will not fade or deform, and their shape is ideal for creating complex charcoal products.

Principle of operation

According to the principle of operation, the brazier from rims is similar to some other home-made models, for example, made from a barrel or a cylinder. It combines the following features:

• grill - allows you to cook on skewers or a removable grill;
• barbecue - for frying steaks, complemented by a lid that creates the effect of an oven;
• hob - the shape and diameter of the disk allows you to put a boiler, pan or pan on the fire;
• smokehouse - some models allow hot smoking of products.

The principle of operation is extremely simple. Firewood or ready-made coals are loaded into the lower part. A grate is installed on top or skewers are stacked. The dishes can also be placed on the grate or directly on the wheel if their diameter is compatible. The heat from below warms the air and allows you to cook like on a regular grill. For smoking, you need to close the top exit and ensure that the wood chips smolder so that smoke forms.

Each design is thought out individually, adjusted to the needs of the owners. However, the main part of the work on the manufacture of the product remains common to all models.

Versions

In more detail, you need to consider possible options for the execution of the product. If you want to make a brazier from car rims, you need to pay attention to the following models:

• Simple grill. The wheel is a container for coals, on which skewers or a grate are placed (We recommend that you study the material on our website).

The simplest option is a brazier for skewers

• Double construction. 2 wheels are used, thanks to which the brazier becomes higher. Due to this, you can put a cauldron on top. Heating from all sides allows you to cook delicious dishes in it, like in the oven or stew them.
• closed oven. Allows you to smoke products, as the smoke is collected inside the chamber and is removed in a small amount through special openings.
• complex models. It combines all 4 functions of the product described earlier. Additionally, other useful elements can be mounted, for example, a chimney.

It is also worth noting that such a brazier can be made with legs and without legs. The stand will be needed for single models, but in double and triple models, its function is performed by the lower disk. At the same time, there are restrictions regarding the use of the structure, because damp ground can prevent the formation of heat, and hot metal is not allowed to come into contact with the wooden floor on the terrace.

We make a brazier from disks on our own

In order to independently make a brazier from auto disks, it is necessary to think over the scheme of the future product in advance. Decide on the amount of consumables, prepare the tools. To perform high-quality work, it is necessary to have the skills to use a grinder for cutting metal, as well as a welding machine.

Preparation of materials and necessary tools

In order to make a brazier from rims with your own hands, you will need the following materials and tools:

• old auto disks;
• Bulgarian;
• nozzle for cutting metal;
• rust cleaning disc in the form of an iron brush;
• file;
• drill;
• a hammer;
• bolts;
• profiled pipes or steel bar;
• grill grate.

Bulgarian and welding machine - the main tools when working with metal

All these tools will be needed to process and connect the details of the brazier. It is convenient to make legs from profiled pipes and rod. In total they will need 3-4 pieces.

Tip: it is better to make 4 supports for greater stability of the product. The tripod may tip over to one side when placed on an uneven surface.

The wheels themselves need to be prepared in advance. If there are traces of rust and paint, the surface is cleaned with a metal brush using a grinder or drill. All excess is cut off.

Easy option

Several options for the manufacture of such grill structures should be considered. You need to start with the simplest - a single brazier from a wheel disc with legs. In order to make it initially, you will need to carry out a series of manipulations with the disk itself:

1. On one side, the inner part is cut out - the partition. A container is formed, similar to a bowler hat.
2. If there are too many holes in the bottom or they are large enough for the coals to wake up through them, an additional plate must be welded on. You should not completely close the gaps, as the coals must be blown to maintain heat.
3. Legs are welded on the sides to the bottom or closer to the top. Usually they are made 40-45 cm in length. This height of the brazier is optimal, as it ensures the stability of the structure and ease of use.

Next, if necessary, you need to clean the sections so that there are no sharp edges left. You can optionally install a grille. It is not necessary to weld it, it is more profitable to use removable parts. Also, for the convenience of maintaining heat and cleaning out the ashes, you can make a window for firewood on the side of the disk. For transfer, the structure is equipped with handles, welding them symmetrically on the sides of the wheel.

Tip: if you use two or three wheels, you can limit yourself to welding metal bars to the bottom. In some cases, you can do without supports at all.

Smoking chamber

It is more profitable to make such a brazier from car disks, which can be used in different directions. For lovers of homemade balyks and sausages, a smokehouse will become an indispensable tool. In order to turn old wheels into such a useful thing, you need to use at least two units of material.

The principle of operation is that you need to connect two disks into a single hollow structure. The top can be adapted for frying kebabs according to the principle of the previous model, but to save smoke, you need to take care of arranging the lid and the smoke extraction system. You can leave the partition with holes, which will simplify the task, and use the product as a hob.

Structural and functional features of the brazier-steam locomotive, the cost of the product, the selection of materials for self-production, the technology for mounting the structure.

In order to combine two disks, it is necessary to cut off the partitions. Next, the wheels are joined and welded with a continuous seam to each other. Legs are welded to the bottom of the lower element. To provide access inside, a door is equipped. To make it, you need to walk with a grinder approximately in the middle of the product and cut out a rectangle.

To fix the door, one nut is welded to it, symmetrically with respect to the weld. 1 bolt is also attached to the barbecue by welding so that the door nuts can be put on them.

Tip: in order to fix the sash without any problems, the bolts are initially screwed into the already welded nuts. Then the door is applied to the opening and fixed already on the structure itself.

Such home-made barbecues allow you to equip all the conditions for relaxing with barbecue with minimal equipment costs. In addition, you don’t have to apply any extra effort, because all the stages of work are extremely understandable and easy to implement.