Plastic pipe furniture: do-it-yourself PVC chair. Useful crafts for giving from plastic pipes Do-it-yourself garden furniture made of plastic pipes

Increasingly, it pleases with unusual innovations, expanding the traditional perception of things. So today we present to your attention a home-made stool made of PVC pipes, which any master can make. Go!

Materials:

• PVC pipe, diameter 25-32 mm;
• Fittings: cross - 2 pcs, straight connecting tee - 8 pcs, plug without thread - 8 pcs;
• Plywood, thickness 10-16 mm;
• Self-tapping screws for screed benches;
• Varnish or paint on wood.

Tools:

• Soldering iron for PVC pipes;
• Electric jigsaw;
• Screwdriver or Phillips screwdriver;
• Sandpaper or grinder;
• Plumbing scissors or hacksaw;
• Paint knife;
• Tape measure, pencil or marker.

The procedure for assembling a stool from plastic pipes

We solder the crosses

The basis of our stool will be two crosses of the same size, acting as the upper and lower tsargs. For one cross, you will need the following fittings: a cross - 1 pc, a connecting tee - 4 pcs, a pipe section for the drawer side - 4 pcs. The length of the pipe is measured empirically, taking into account the distance for soldering.
The finished cross should turn out to be square, and its size should be several centimeters smaller than the size of the bench on each side. Soldering is carried out with a sanitary soldering iron, with an optimal time delay for the selected pipe diameter.
The most even cut of PVC pipes is obtained with specialized scissors. However, this tool may not be available to everyone. You can replace it with a hacksaw, trimming the curvature of the cut with a paint knife. They also remove burrs for better soldering.
Advice!
The cost of PVC pipes differs depending on the quality, manufacturer and destination. For example, hot water pipes are much more expensive than cold water pipes. For similar products, it is not the type of pipe that matters, but high-quality and reliable soldering.

Making a stool frame

With segments of PVC pipes of the same diameter, we assemble both crosses together, making a stool frame. You can accept the general dimensions that the author of the video sets in his product.
The advantage of PVC pipes as a material is that with an inaccurate choice of dimensions, you can always solder or, on the contrary, cut the pipe in length. In our case, it is worth considering the presence of plugs on both sides of the frame. They can be soldered through small pieces of pipe, thereby adjusting the height of our stool.

We make a bench

The seat of a stool is called a bench. We make it from a square piece of plywood. The usual size of a stool bench is 30-35 cm. we cut it with a jigsaw or a hacksaw, filling up the edges along the correct radius. With sandpaper or a grinder, we process the edges and sawn edges around the entire perimeter.
We mark four holes for self-tapping screws for attaching the bench to the frame. We slightly countersink the holes from the front so that the caps of the screws do not stick out from the outside. We drill holes with a screwdriver or drill. The banquette is almost ready. For longer-term use, it can be painted or varnished.

We collect a stool

We expose the frame of the stool exactly in the centers of the holes. We bait self-tapping screws by hand, and twist them with a screwdriver or screwdriver. We check the stability of the stool so that all legs are uniform.

We have got an excellent example of country furniture, which, thanks to modern materials, will serve faithfully for more than a dozen years. The cost of components is quite low, and for many masters they generally settle as a reserve in a deep stock. We offer you a wonderful way to use them for the benefit of business and economy, because for this, in fact, they are needed. Good luck and good mood to all masters!

As a rule, after the replacement or construction of a water supply system, plastic pipes and fittings often remain. Of course, such material is no longer suitable for reassembling communication networks, but it can be used to make various decorative crafts and practical things.

If you wish and have free time, you can make a chair from polypropylene pipes with your own hands - the assembly technology is very simple and can be done by any home craftsman. Do you want to assemble original furniture, but don't know where to start? We will help you to realize your plans.

The article describes in detail three technologies for the manufacture of various crafts. By following these instructions, you can assemble a high chair, a kitchen stool and a portable fisherman's chair with your own hands.

There is something attractive about furniture created from improvised materials. So, plastic pipes allow you to make designs of ideal geometric shapes. They will add zest to the interior of the room. In addition, the owner of such furniture will have a great chance to show off to his friends a masterpiece he has created with his own hand.

Chairs made of plastic pipes have the following advantages:

• ease;
• compactness;
• strength;
• ease of manufacture.

And the most important thing is that they can be built with your own hands, in a relatively short time. This will require a minimum set of tools and materials, and a little patience.

It is necessary to start manufacturing a chair from polypropylene from the choice of the design of the product and its design embodiment. At the same time, you need to build on the function that the furniture will perform.

If there are a lot of pipe scraps left, then you can build a chic creative armchair or bar stool from them. To fasten parts, it is not necessary to have an iron for soldering, this can be done using special glue

Having decided on this, they begin to select the parameters of the product: the size of the future structure, its type (collapsible or solid), the method of connecting parts. You need to draw a rough sketch of the future product in order to understand how much and what material will be needed to work.

The design of PVC chairs is limited only by human imagination. To get ideas, you can look through interior design magazines or furniture catalogs. It is not necessary to look only at plastic products, ideas can be gleaned by looking at furniture made of any material.

Stools made of plastic pipes can be placed in the kitchen, country veranda, garage, and just in the yard - they will look stylish and original everywhere.

For trips to barbecue or fishing, you can build folding chairs that are convenient to store and transport when folded, while they do not take up much storage space.

For children, you can make comfortable and bright chairs by covering the frame of polypropylene pipes with a fabric of bright colors.

The process of building a chair

Creating an original chair from plastic pipes is quite within the power of any home craftsman or craftswoman. To work, you will need a minimum set of tools, which is sure to be found in every home and, of course, the remains of polypropylene pipes.

Step 1 - project of the future chair

At the first stage, it is necessary to decide on the purpose of the chair and its design. If you decide to make a bright chair for a child, you should definitely take into account the height of the small owner.

If you plan to use the stool in the kitchen or in the country, in order not to miscalculate with the size, be sure to measure the height of the existing furniture.

For those who first decided to try their hand at this creative and creative work, it may be worth starting with the manufacture of the simplest design - a stool. It does not require a lot of skills and materials, and having coped with this task, you can begin to manufacture more complex structures.

Image Gallery

Cut off a piece of fabric 18 cm wide. It is better to opt for a dense material with a water-repellent impregnation. A piece of tarp might also work.

Using a reinforced thread, sew along the narrow sides of the rectangle so that you get holes for the pipes. If threads are pouring out of the fabric, then it is better to tuck it and stitch it on all sides, but allowances must be taken into account even before the fabric is cut

Making a chair out of PVC pipes with your own hands is within the power of any craftsman who has experience with household tools. Furniture made of polymeric material is durable, light, elegant, comfortable, resistant to dampness and solar radiation. Products made of plastic pipes have a long service life, they are used at any time of the year, both indoors and outdoors.

Similar articles:

Types of PVC Chairs

The distribution network receives products manufactured using various technologies. Pipes are designed to create a water supply or sewerage system, they have differences in connection methods. The specifics are as follows:

1. Structures made of polypropylene pipes are joined using a soldering unit. After welding, they become monolithic. With the help of threaded fittings, furniture is collapsible. This solution allows you to transport it in the trunk of a car or carry it in a small bag.
2. Do-it-yourself PVC pipe chairs are assembled by gluing fragments or inserting them into couplings. This method is simple and does not require the use of special equipment. The use of products with couplings and cuffs allows you to create collapsible chairs with the possibility of their temporary weighting with bulk materials.
3. Stools made of plastic pipes are made in various colors. The blanks themselves have different shades (white, gray, black, orange). Furniture can be covered with acrylic paint. This decision is made when the master wants to quickly get rid of the applied markings.

According to their design, PVC chairs can look like this:

• only legs and seat;
• with a straight or inclined back;
• with armrests;
• with separate or combined legs.

Necessary tools and materials

Before you make a chair out of plastic, you need to purchase the equipment and property you need for this.

To work, you will need the following tools:

1. tape measure or pipe cutters;
2. hacksaw for metal;
3. oil level;
4. screwdriver;
5. special soldering iron;
6. drill or screwdriver;
7. stapler;
8. marker.

The materials needed are:

• PVC pipes;
• wood screws;
• fittings (corners, tees, plugs, contours, crosses);
• plywood 8-10 mm;
• foam rubber 50 mm;
• upholstery fabric;
• thick canvas.

The number of fittings and pipe footage depends on the chosen design and construction. The seat can be made from thin tubes, strips of tarpaulin, or foam rubber attached to plywood.

Calculations and drawings

You can design a chair from pipes on a piece of paper or a personal computer. Complicated calculations do not need to be done, since the products have a simple design.

When planning work, the following nuances should be taken into account:

1. Using the curvature factor. Curved fragments look more interesting and attractive than straight links. A chair with a sloping back will fit better into any interior. It is possible to give the workpiece a curvilinear shape by slowly heating it over an open flame. Then it is gently bent and fixed until it cools completely. Another way is to use factory-made contours.
2. The length of the pipes is selected taking into account the fact that part of the workpiece will be immersed in the fitting. This distance is 20-50 mm depending on the type of plastic pipes. Before drawing up a drawing, it is necessary to experimentally measure how far the links go into the opening of the coupling.
3. It is better to take a sample that is comfortable to sit on as the basis of the project. You can add your ideas to it. Keep in mind that plastic bends under pressure. To increase the strength of the finished product, transverse ties on the legs and the seat are provided. Reinforced plastic is much more practical than analogues without aluminum inserts.
4. The diagram is drawn to scale with an accuracy of 1 mm. It displays all the details, places and order of joining blanks to each other, screeds and partitions. A variant of cutting blanks is provided, in which the amount of waste will be minimal.
5. If the workpieces are connected without glue and soldering, then the joint must be strengthened. For this, screws are used, which are screwed in so that they tighten and fix both fragments. It is better to screw the hardware on the underside of the pipe and from the back. So they will be almost invisible.

The finished scheme is the basis for the calculation of building materials.

What do you do with old furniture?

Poll Options are limited because JavaScript is disabled in your browser.

With skill and a rich imagination, interesting and useful things can be made from any materials at hand, including plastic pipes.

Plastic pipes of different diameters are sold at any hardware store at very affordable prices. They are used in plumbing, sewerage, heating, irrigation systems, and after construction or repair, unnecessary trimming often clogs the site, while it can serve as an excellent material for creative crafts.

Do not rush to take construction waste to the landfill - we will tell you what can be done from a plastic pipe to turn excess residue into beautiful and functional interior items.

What is good plastic pipe?

We will not talk about the direct purpose of the product, but about the convenience of using varieties of plastic pipes precisely as a material for crafts. Plastic pipes are light weight, strong and durable enough. They are resistant to dirt, do not collect dust and are easy to clean. Products made of plastic pipes are safe to use even by small children (they do not break, do not have a heavy weight, do not emit toxins).

For creative work, PVC pipes are more often used, which are quite rigid and easily connected with special nozzles and "adapters", allowing you to get collapsible structures. Polypropylene pipes can also be used, but their connection will require a special welding machine or compression fittings, and finished products can no longer be disassembled.

Methods for connecting pipes in structures

From plastic pipes, you can make not only convenient household items, but also pieces of furniture. In order for such a home-made product to last a long time and be reliable in operation, care must be taken to properly connect the individual segments. Since it has already been said about the connection of polypropylene pipes, we will consider the connection of only PVC pipes.

PVC plastic pipes can be connected in the following ways:

• in a bell with a rubber seal;
• with the help of an adhesive composition;
• bolts by drilling holes.

The first connection method is characterized by simplicity, but insufficient rigidity. Before joining, it is recommended to clean the internal and external surfaces of the pipes at the joint from dust particles and treat the inserted part of the pipe with silicone grease. First, the pipe is inserted into the socket until it stops, after which it is carefully pulled back by 0.7 - 1 cm. The structures assembled in this way can later be dismantled, which is convenient for seasonal products.

The second method of assembling pipes is distinguished by reliable fixation and greater labor intensity. Work on connecting parts begins with the processing of the mating surfaces of the socket and pipe with sandpaper for better adhesion. Then they must be degreased with methylene chloride. The adhesive composition is applied along the entire length of the prepared outer surface of the pipe and 2/3 of the length of the inner surface of the socket. Finally, the pipe is inserted into the socket until it stops and rotated a quarter of a turn. For gluing, it is required to press the parts for 1 minute. For good fixation, all operations to connect two segments must be carried out quickly enough. The connected elements are left for several hours until the adhesive composition dries completely.

The third method is more time consuming, as it requires marking and preparing holes, but allows you to get collapsible structures with a reliable connection.

For corner joints and connecting several segments at once in one node, it is convenient to use a variety of fittings. Plastic pipe structures can be of any complexity using numerous tees and fittings. Consider useful homemade products in order of increasing complexity of execution.

Original and functional little things for decorating the interior

Our review of interesting ideas is opened by the simplest products from a plastic pipe, which even novice masters of homemade art can make. In addition, such crafts require a minimum amount of material, and in some cases even the shortest trimmings can be used.

From scraps of pipes of large and medium diameter, you can make a convenient and practical organizer for your office or workshop.

There are two options available here:

• fastening with self-tapping screws to a wall or table, for which one end of the segment is cut off at an angle - a stationary option;
• gluing the segments together to form a stable figure is a portable option.

The segments can be left white or gray, or you can paint it in your favorite color. Such an organizer is indispensable for schoolchildren and people involved in creativity and needlework. With him, everything will always be at hand, and on the table - the perfect order.

Additional comfort on the desktop will be provided by a drawing tablet and a laptop stand, which can be made from small-diameter polypropylene pipes.

Bookshelves are a special element of the interior. Their presence in a certain way characterizes the landlord. High-tech style corner shelf will not go unnoticed.

From numerous short cuts of different diameters, you can make a patterned frame for a mirror or photograph. It is enough to glue the cut rings according to a pre-prepared layout, which can be applied to a sheet of cardboard. It can be floral patterns or something abstract. The dimensions of the frame will depend on the amount of suitable material.

Scraps of large diameter can be used to create a comfortable shoe shelf with numerous compartments-cells. This design will not take up much space in the corridor and will ensure proper storage of shoes and a quick search for the right pair. The elements are connected using glue or self-tapping screws. To fix the shelf on the wall, you can use a plywood sheet, to which the assembled shelf is first glued.

Some crafts made from PVC pipes will really appeal to lovers of fresh flowers. A reliable flower stand is simple in execution and looks pretty.

For the manufacture of flower pots for transplanting or breeding pets, small pieces of sewer pipes are well suited. Having shown imagination, such pots can be decorated with colored paper, paint or bright stickers.

It is easy to make a stylish vase for artificial flowers and dried flowers from elongated cylinders of medium diameter. If you approach the implementation of this idea creatively, then an original gift for a significant event can come out.

Another extraordinary idea for the interior is homemade techno-style lamps. There are a lot of execution options, but they all adhere to the principle of minimalism: no unnecessary details.

With the help of unused scraps, you can also make useful things in the hallway or corridor: a hanger for clothes and bags and a holder for garbage bags.

Crafts from plastic pipes for the playground

From PVC pipes, you can make a lot of crafts for children's entertainment in the yard: a developmental rug, an arena, a swing, a sled, a football goal, a playhouse, an outdoor shower and a theater screen.

A very useful design for kids is a playpen made of PVC pipes.

Kids will love the lightweight swing that dries instantly after a warm summer rain.

In winter walks, homemade sleds will be the most reliable and fastest. The design is quite complicated, but with the help of practical videos you can figure it out.

For active games in the yard, safe football goals can be made from the remnants of plastic pipes.

Many children often dream of their castle in miniature. Making your childhood dreams come true is quite simple and not at all expensive. The frame is done very quickly. It remains to pick up a beautiful dense material for the roof and walls, and the house is ready!

The following structure will help to freshen up on a hot summer day. Such an open shower will be a joy not only for children, but also for adults.

From polypropylene pipes you can make a theatrical screen. It is enough to collect 3 frames, connect them together and close them with beautifully designed curtains. The home theater develops the creative abilities of children and creates good conditions for an exciting pastime.

We update the interior economically: furniture made of plastic pipes

Crafts from plastic pipes with their own hands can occupy a key place in the interior. Craftsmen share many extraordinary solutions that can significantly save the family budget. Let's highlight the brightest of them.

The most common and sought after piece of furniture is a chair. Using pieces of plastic pipes and connecting elements, you can make high-quality chairs of various types: children's chairs, folding chairs for hiking and fishing, armchairs and even high chairs.

Having mastered the assembly technique a little, you can proceed to more complex structures. A neat bunk crib made of polypropylene pipes is a good alternative for a country house or cottage, when buying a ready-made crib is too expensive. Moreover, when the kids grow up, the material can be used to make other useful crafts.

The glass coffee table with a PVC pipe base in the next photo can hardly be called an amateur homemade product, because it looks like a design work.

Another original idea is a shelving unit for a hallway or living room. Having independently designed a rack with the right number of shelves of the required size, you can not waste time shopping in search of something suitable.

Useful crafts for a country house and a summer residence

Unused and superfluous building materials will definitely find application in the summer cottage. Crafts from plastic pipes for summer cottages will significantly facilitate garden work, make your stay more comfortable and help you avoid high material costs. At the same time, the designs look neat and stylish.

From small lengths and a few tees, you can get a nice dryer for clothes and towels. It is easy to clean and does not corrode.

Relaxing by the pool or in the shade of the garden is impossible to imagine without a sun lounger. The photo shows a chaise lounge, completely consisting of plastic pipes, but can also be combined with dense matter.

A carport is another useful application of PVC pipes. It will protect transport not only from a rain, but also from the scorching summer sun.

For garden decor, a garden arch is often used, which can also be made of plastic pipes. A new element appears in its design - bent arcs. You can bend pipes for an arched vault by heating with a gas burner or boiling water. You can also put the pipe on a metal rod and, sticking one end into the soil, bend it in an arc. This method requires some physical effort.

A simple and light gazebo will decorate the garden and protect from the sun and light rain. For the presented option, it is enough to fix a waterproof raincoat fabric on the pipes and bend them on reinforcing bars. To make the design reliable, you need to take care of good fixation of the rods in the soil.

The range of application of plastic pipes is truly huge and limited only by your imagination and needs. You need a small woodcutter, a gate, a cart or a fishing rod stand - take the required amount of pipe and bring your idea to life.

It is easy to make a convenient feeder for chickens from sewer pipes. It is very convenient to pour grain with it without going into the corral. Chickens cannot rake grain in such feeders, which saves feed.

A small greenhouse in a summer cottage can also be made from plastic pipes. The easiest option: make a rectangular frame and cover it with a film or agrofibre.

A more serious construction - a seasonal greenhouse - will require more time and material. It is better to connect the elements with bolts so that it is possible to disassemble the structure for the winter. The optimal shape of the greenhouse is arched. To create it, the ends of the pipes are put on half-meter metal bars driven into the sides of the future greenhouse every meter. The dimensions of the greenhouse depend on the intended use. The greenhouse can be installed on the foundation or on the ground. Film, polycarbonate or agrofibre can be used as a covering material.

Plastic sewer pipes can also become a container for growing flowers, herbs and vegetables. Very often they are used to create vertical gardens.

To fence the site, you can use a low fence made of plastic pipes, which is durable and has minimal maintenance requirements (it does not need to be painted every year).

The use of plastic pipes is not limited to the ideas presented. This material is so versatile and easy to assemble (it is easy to cut, bend, has a variety of connecting parts) that it is simply impossible to ignore it in your home workshop.

What can be made from plastic pipes

For most, the question immediately arises: “is it possible to replace PVC pipes with polypropylene?” . You can use polypropylene pipes, only in this case we still need a soldering iron.

Advantages of PVC pipes:
- snow-white color;
- you can connect pipes with fittings with glue, or without it at all;
- if you do not use glue, then the structure will turn out to be collapsible, and like a LEGO constructor, you can use fittings and pipes to assemble other structures.
Of course, polypropylene pipes are deprived of these advantages.

And now, let's see what crafts you can make from plastic pipes with your own hands:

From plastic pipes you can make:

Highchair made of 1″ pipe

Camping folding chair from 1″ pipe

Country tables and chairs from 1″ pipe, for outdoor use

Greenhouses, greenhouses and light frames on the beds for sheltering plants, assembled from polypropylene pipes and connecting elements, are a very budget option that combines low cost and ease of assembly. If necessary, they can also be easily dismantled.

Strong and stable racks for growing and working with seedlings.

PVC pipes of a larger diameter, neatly sawn from above with a jigsaw and filled with soil, are a compact and aesthetic option for planting greenery.

Children's bunk bed (3/4″, 1″ and 1 1/4″ pipes were used)

Bed for dogs, the diameter of the pipe in this case is selected based on the size and weight of the dog.

Suspended swing for giving

Sledge for household work in the winter in the country

From the rest of the pipes of large diameter, you can make a small organizer in the garage

Clothes dryer made of PVC pipes.

Having attached, wheels we will receive rather convenient carts.

A greenhouse made of PVC pipes will serve you for many years, it does not need to be painted, and it will not rot or rust, as is usually the case with greenhouses made of wood and metal.

You can assemble hydroponics from plastic pipes, but in this case I want to note that you can use any pipes (including sewer pipes)

Children's car made of plastic pipes

Or make a pen for chickens

Racks that can be easily assembled to any size

Collapsible outdoor tents and tents made of plastic pipes

Grating grate made of plastic pipes that will always have a pleasant appearance.

Canopies for cars from plastic pipes

Fences and barriers made of plastic pipes

PVC pipes are an easily accessible material for useful ideas and household appliances. What do you need for this? Hacksaw, tape measure, glue, in some cases sandpaper.

1. Rack for drying clothes.

2. Drinker system in the chicken coop.

3. Little boy.

4. Shelves.

5. Rack for bicycles.

6. Rack for containers with vegetables.

7. Summer velomobile.

8. Various tool holders.

10. To store shoes.

11. Summer shower for children.

Simple designs of garden furniture, assembled from polypropylene pipes, will help you relax and unwind in a shady corner of the garden.

How do you, for example, comfortable models of chairs?

A comfortable sun lounger, an impromptu canopy for a morning meal in the fresh air, or such a “life hack” stand model that allows you to train on a treadmill without leaving the Internet? Cheap, reliable and practical!

Children in the country are a separate burning topic. The ubiquitous children must be given the opportunity to play and misbehave in such conditions that parents are calm.

For kids in the country, you can assemble such a comfortable playpen or a cozy toy house. These designs are easily transferred to the garden or to the veranda, and your child will always be in your field of vision.