Hello dear readers! Today we will talk about the correct installation of roller blinds on plastic windows. Modern systems that protect the room from sunlight are functional, look elegant, are easy to operate, and their installation is so simple that even a housewife can handle it.

To install roller blinds, we need:

• roulette;
• pencil;
• building level and long wooden plank;
• hacksaw, scissors or clerical knife (if necessary, cut the curtains in width).

If you decide to install the structure with drilling, additionally stock up on:

• an electric drill with a 6 mm drill + dowels (for walls or ceilings) or 2.5 mm for wood (for a window system);
• Phillips screwdriver or screwdriver.

To install roller blinds without drilling, you need to additionally prepare:

• solvent for degreasing the surface;
• double sided tape (if not included)
• construction glue (for more reliable fixation of elements).

Preparatory stage

Before purchasing curtains, choose the principle of their installation. The canvas can completely cover the window opening - in this case, the structure is attached to the wall above the window or ceiling. If the upper part of the frame is wide enough, you can install a roller blind on it, but in this case, when the curtains are closed, it will not be possible to open the window for ventilation. There are also roller blinds that are mounted directly on the sash and do not interfere with opening windows.

If you opted for curtains fixed to the sash, check the verticality of the window installation using a level. On strictly vertical window systems, it is allowed to install roller blinds with a free edge - there will be no gaps between the canvas and the frame that let light through. In other cases, it is recommended to use roller blinds with curtain guides.

Take measurements with a tape measure according to your choice. If there are no curtains of a suitable width on sale, buy wider ones - the excess can be easily cut off. To cut the pipe on which the canvas is wound and the wooden bottom bar, use a hacksaw.

To calculate the length of the shaft when trimming the curtain, measure the required width of the curtain and subtract 8 mm from the resulting value (2x4 mm - the width of the two brackets). Cut the plank to the desired curtain width. Applying the cut bar to the edge of the fully unfolded canvas, mark and cut off the excess material along the entire length with scissors or a sharp knife.

The width of the curtain leaf on the sash with guides must correspond to the width of the double-glazed window, plus 3 cm. The curtain with a free edge is somewhat wider, as it should overlap part of the frame. At the same time, she should not cling to the handle on the fold.

If you are planning to attach a roller blind to a ceiling or wall above a window, make sure that the finish will not be damaged while drilling the holes.

Drilling installation

Choose which side is more convenient to place the control chain, because the bracket for mounting the control mechanism has a special configuration.

Then mark on the frame, wall, in the window opening or on the ceiling the location of the bracket for the control mechanism. According to the marks, drill holes for its fasteners. Install the bracket without fully screwing in the screws.

To determine the location of the brackets on the wall or ceiling, determine the central axis of the window opening, set aside equal segments to the right and left of it.

Insert a mechanism with a chain on one side and a plastic tip on the other into the ends of the shaft. Install the mechanism in the bracket and, using a building level and a wooden plank, align it horizontally, accurately determining the installation location of the second bracket.

Drill holes for the second bracket, fix both load-bearing structural elements. Insert a shaft with a pre-fixed curtain into the brackets - first the end with the mechanism, then with the plug.

To fix the curtain on the shaft, it is necessary to bend its upper edge by 5 cm, forming a fold. A shaft with a self-adhesive strip, from which the protective film has been removed, is installed in the fold with the adhesive side up, and then rolls towards the upper edge. It is important that the canvas is glued to the shaft strictly horizontally.

Then fold the canvas almost completely and insert the bar into a special slot on the bottom edge. Correctly install the mechanism in the shaft - the canvas should be located close to the window.

Mounting without drilling

The principle of assembling a roller blind and its installation remains the same. The difference concerns only the features of fastening the brackets - they can be glued to the sash or fixed on its upper edge using special hooks.

Hook fasteners are used if the sash with a seal has a suitable thickness. In this case, the bracket is assembled from parts according to the manufacturer's instructions and installed on the upper edge of the open sash according to the preliminary marking. Then the roller blind shaft is inserted into the brackets. Make sure the sash with hook brackets closes properly.

Brackets, provided with an adhesive layer, are attached to the surface of the sash. To make the fixation as reliable as possible, be sure to degrease the installation site. Additionally, you can use a suitable construction adhesive.

The guides are also equipped with an adhesive layer - remove the protective film from it and attach the bar to the degreased surface, inserting the upper edge into a special groove in the bracket.

At the end of the installation of the roller blind on the chain, with which the canvas is raised and lowered, limiters are installed - small plastic washers with a slot. The first limiter is installed on the chain when the lower edge is raised to the required height, the second - when the curtain is completely lowered.

Video on the topic "how to fix roller blinds on plastic windows":

Blinds have won respect for their simplicity and convenience. They are durable and can be on the windows for a long time without causing irritation to the residents.

Blinds are a practical and convenient window decoration option.

The variety of designs and colors on the market is simply enormous.

How to hang roller blinds on plastic windows

But the price is not always affordable for the buyer. And sometimes you just want to see objects created by your own hands around you. In both cases, the solution is this: make the blinds yourself. Moreover, it can turn out beautifully, unusually and inexpensively.

What materials and tools will be required?

Scheme of assembly of vertical blinds.

To make blinds with your own hands, you will need a small set of tools and materials:

Where to begin?

The scheme of fastening the blinds to the window.

It will be easier to make vertical blinds, so let's dwell on the description of their technology.

We select a roll of paper so that it is 2 cm narrower than the width of the window opening. We measure 3 cm from the bottom cut and bend the sheet. It is necessary to fold the length of the paper equal to the height of the window with an accordion. We put the accordion under the press for 2-3 hours.

Now you need to find the middle of the folded paper. On both sides of the middle at a distance of 3 cm, through punctures must be made. An awl is quite suitable for this purpose. The paper is attached to this rail with adhesive tape or simply glued.

How to assemble a structure?

Scheme of vertical blinds with an inclined system.

Vertical blinds are ready, you only need to assemble them and correctly position them on the window.

First, glue the lower part of the folded paper in the center with tape. The thread is threaded through the hole from the bottom up, then unfolded and threaded in the opposite direction. One end of the thread is equipped with a bead.

At the second end, it is necessary to place a movable clamp. Usually a clothes clip is used, but it will not look very nice. It is better to have complete symmetry, so it is recommended that these parts be draped in the same way.

Here you can use various drapery schemes for small details (bells will look very nice and hide the clips).

In order for the thread not to wear out quickly when rubbing against a wooden rail, it is recommended to place a roller in the central part of the rail.

Now vertical blinds should be placed on the window. The paper will sink under the force of gravity. This will be the extreme position for the fixed bead. The movable clamp is located at the same height.

We tie knots under the marked details and cut the ends of the thread.

How to check mobility

Fixed the clamp and got the desired position.

The edges of the bottom of the vertical blinds will sag. To eliminate this small flaw, you can equip the lower part of the blinds with a thin plate of any material, gluing it with double-sided tape.

For lovers of more refined interior elements, it is recommended to connect fantasy. It will turn out very attractive if both lower edges are brought together and fastened with glue or the same adhesive tape. The result will look like a heart. What is not an option for lovers?

Where can you use homemade blinds and how to repair them?

Installation of vertical blinds.

It is clear that do-it-yourself blinds are made for use for a short period of time.

This is usually done before the start of the repair. So you can regulate the amount of light penetrating into the apartment and save the finishing materials from fading.

Homemade blinds are suitable not only during the repair period. They can be considered as an excellent alternative to factory products in country houses, garages and utility rooms. Home-made vertical blinds are used seasonally: in the summer, they prevent light from entering the apartment, which helps to escape from the heat.

It is not difficult to repair home-made vertical blinds.

It consists in replacing paper (you will have to make a new accordion). When assembling a new product, the same procedure is followed.

Scheme of movement of vertical blinds.

Do-it-yourself blinds do not have to be made of paper.

Home craftsmen advise using ordinary starched fabric for this. This makes sense: the material is thinner, the harmonica is easy to make with an iron. The fabric can be easily removed and washed, making the vertical blinds more durable.

You can experiment with the lower part, giving the product completeness at your discretion.

But when using fabric for vertical blinds, you need to slightly weight the bottom of the product. Usually, for this purpose, the lower edge of the fabric is folded in half and stitched at a distance of about 5 mm from the bend. Later, a metal (aluminum) wire is inserted into this hole. It will make the blinds heavier and keep their bottom edge in a horizontal position.

This can be avoided if the edges of the holes are glued with adhesive tape or treated with metal rivets with holes.

You can overcast holes with ordinary thread. The edges of the holes will be stronger, which will make handmade vertical blinds even more durable.

Repair of factory-made vertical blinds can be done according to the same rules as described for homemade products. But the replacement of a certain part of such blinds will be visible even to the naked eye. It will not work to hide the flaw, since it is very difficult to choose a material of a certain color range. And you don’t need to do this: it’s enough to immediately replace several elements during the repair.

It will turn out very beautiful and elegant. It will look as if blinds and curtains were specially combined.

Overview How to assemble vertical blinds with your own hands.

Making a blind roll with your own hands is a task that every home owner can perform.

Planar scheme of weighing.

The lifting mechanism used in this embodiment is in the form of a shaft, raising or lowering the curtains due to its rotation.

These do-it-yourself curtains are an easy task and fun to do, you need to buy the necessary materials and tools.

The use of roller structures with a lifting mechanism in each room can transform it without recognizing it, and can solve a wide range of design solutions.

But when installing curtains, you must consider all shades, as both of you can make the design elegant and completely destroy the design idea.

Blinds or blinds are located directly on the frame or in the window, although they seem simple, but no less interesting than expensive curtains or lambrequins.

Roller structures have a convenient lifting mechanism, so they have found their application both in offices and in apartments.

Blinds Benefits

These elements are equipped with a convenient lifting mechanism, you can use them alone or together with other window decoration elements.

This design can be installed on plastic and wooden windows. Close the window and take care of them.

This design has a simple lifting mechanism, so it fails when using such curtains.

Once properly installed, they allow you to completely turn off the room, there is a wide choice of colors.

Some people replace pilgrims and blinds.

They are similar in appearance, but Roman blinds consist of a rope system, and the blinds have a lift mechanism that rotates and is located at the top of the structure.

Types and types of blinds

Shaft design can be open or closed, electric motor can be used for easy shade control.

Rolling structures can be with or without cassettes, lofts or shutters.

The control principle can be set manually by means of a chain or an electric drive.

How to hang blinds on plastic and wooden windows with your hands

There are such models, and there may be different types of fabrics for the material used.

Characteristics of creating independent rolls

Let's look at an example of creating such a shape with your own hands, while the roll is at the bottom, and at the desired height, the canvas is attached using strips.

First measure the windows where this curtain is attached.

The width of the fabric should be 2-4 cm more than the given size, and the length should be more than 5-15 cm. Depending on which room you will install this design in, select the fabric and pattern.

For work you will need:

• two pieces of fabric of the required size;
• tapes to be used as covers should be twice as long as curtains + 30 cm;
• a wooden bracket or hose for fastening, their width should be 1 cm less than the width of the curtain, you can buy a ready-made cassette system;
• stick or weight rod;
• screwdriver and screws;
• stapler;
• thread, needle.

Work order

Tilt two pieces of fabric on the wrong side and stitch on three sides, then wring out the bag.

Now you have to insert the weight, or you can make a special pocket for it.

The fabric is hungry and kept on a wooden stick, if a hose is used, the fabric hangs around it and the seams.

Racks fold in half, and are also attached to the rod with clamps. After that, we fix the beam on the window frame.

Above we can't make this work.

If you plan to remove the curtain, you can attach it to special hooks. For fastening to a plastic window, it is necessary to use double-sided adhesive tape. Creating rolled structures is an exciting process, you don't need to have any specific knowledge or materials, so you get a beautiful window.

WINDOW MAINTENANCE

Put curtains on window panes and it won't be much. However, this requires curtains in a special design together with the appropriate accessories. Such curtains are attached directly to the sheet and rotate with it. They are equipped with a spring-loaded lifting mechanism, and in the positioning position they are fixed with a locking hook.

The coil spring accessories are the flat part attached on the side of the frame.

Into the curtain of the curved curtain slit, insert a wooden rod with a round cross-section that snaps into place with locking hooks attached to the sides of the frame.

Shimmering curtains of different colors and patterns are made in a special capacity for sleeping windows.

THE ROLE OF PROTECTION

BY WIDTH

When installing curtains in niche windows, they may need to be fixed in width.

To do this, the fabric should be unscrewed and cut off the metal shaft with the correct nut. Then draw a line with a pencil on the fabric that limits the desired width and cross it with scissors along that line. Replace the fabric on the shaft and install a narrow curtain.

COMPONENTS AND SPECIAL SIZES

The darker the curtains, the less light they transmit.

They are completely opaque among them.

Blinds on plastic windows

Fabrics of such curtains can be of different colors and with different patterns.

Curtains in a special design can reach a width of 300 cm and a height of 240 cm. Intermediate sizes are also possible.

Roller blinds can be completed with lambrequins of various shapes, such as the last curtain elements. Lambrequins come in a variety of colors and can be mistaken for tons of curtains.

The set of blinds includes supports with which they are attached to the wall, ceiling or side windows of the window niche.

For cleaning, the blind can be easily removed from the brackets.

7 The range of colors and patterns of decorative fabrics for blinds is very diverse - you can choose a fabric for every taste.

2 If the edge of the curtain does not fit, you can decorate it with a cap. Here are lambrequins of three different shapes.

3 Universal plastic brackets that can be attached to vertical and horizontal surfaces.

4 Brackets for mounting rollers on plastic windows.

They are mounted on the frame and screwed.

How to curtain curtains on a plastic window

If you want to close the shutter window, you don't only need a curtain, but also go with guides. If you understand the nuances of installation, install blinds on plastic windows without the help of experts.

Varieties of blinds

Drive systems are classified according to several parameters: type of construction, steering mechanism and production material.

On the first sign, all curtain models are divided into two groups:

Open - the box is not closed by the box, which makes the curtain less compressed against the glass, and the mechanism is not protected from external influences;
Closed - There is a security cabinet that increases the cost of the system but provides better performance.

In addition, the system can have different geometric parameters: the shape of the guides, the diameter of the shaft, the width of the belt.

The choice of size depends on the surface of the hole, so you need to know how to measure the plastic window before ordering the blinds.

You can use the following mechanisms to manage the system:

Plastic chain or chain, for example, with blinds;
spring lock - automatically holds the blade when you unload it to the desired length;
electric drive - the shaft is equipped with a low-power electric motor that can be remotely controlled.

Each option has its own purpose.

Thus, a spring is better suited if the shades do not need to be adapted frequently, and an electric drive is better suited if the system is not available. In most cases, twine is sufficient.
The fabric of the blinds is made of durable materials that do not stick to glass - polyester, cotton, nylon, coated bamboo and metal inserts.

They can provide different air permeability of the curtain; With this feature, the following blinds stand out:

Transparent - diffused sunlight used for decorative purposes;
smoke - partially transmits visible light, but blocks heat;
Fatigue - completely blocks the light;
Day-Night - Alternating sheer and opaque sashes that allow you to let in and block out light without folding the canvas.

Whether or not the canvas is made, it should be cleaned regularly with soapy water, especially if the kitchen has curtains.

Curtain installation device

Before deciding how to hang curtains, you must choose the type of balloon attachment.

The most popular method, which is most suitable for large windows, is wall or ceiling mounting. The shaft must be screwed to the window opening, which creates many inconveniences - for example, a window with a curtain does not open.

In addition, if it ends, such manipulations can get worse. In most cases, it is better to use the installation in the window aperture, as in this case it is possible to mount the system without drilling.

Next, you need to make sure the window is completely vertical - you can use it flat or flat for this purpose. If there is a deviation, the curtain will not fold properly and will not hold the glass well.

In this case, you must mount it on a wall with a small notch from the frame, or repair the window itself.

For a cylinder mounted on a wall or ceiling, add a hole 15 cm wide and 10 cm high;
When installing in a hole - remove N from the width of the aperture, measure the height as it is (N is equal to the size of the brackets depending on the manufacturer of the system).

The designated manufacturer may have their own design and measurement features - this should be checked on the company's website or in the store.

Do-it-yourself prefabricated shutters on a plastic window

Once you've taken your measurements and purchased the system, you can figure out how to hang your blinds.

The easiest way to install them is with self-tapping screws. To do this, you need to do the following:

1. Place the rails on the frame and tighten with the included fastener.
2. Insert the covers and gears into the shaft box or attach them to the shaft if the system is open.
3. Attach the shaft to the bracket by pinning it up and pushing it in until it clicks into place.
4. Close the edges of the box with decorative overlays.

If there is no tool for screwing screws, you need to learn how to repair curtains without drilling.

To do this, you can use the Velcro that comes with the kit. Installation is carried out as follows:

1. Velcro attachments are attached to the rails.
2. The frame of the windows is degreased.
3. Velcro heats up the hair dryer, then removes the protective film from it.
fourth

The system is assembled as described above.

Keep in mind that a Velcro-mounted curtain will not hold as securely as it is attached with screws - the fasteners may need to be replaced for a while.

But if you need to remove the roller blinds, they can be easily soldered in this case.

Installation of rolls on plastic windows from A to Z

In the case of self-tapping screws, the system must be unscrewed. After that, the shaft is separated from the guides, and the network is removed.

Therefore, it is very easy to install curtains - just follow the instructions carefully. If everything is done correctly, there will be no problems with system performance.

← Austrian curtains in the interior of the Egyptian style →

The procedure for attaching roller blinds to windows

Operating instructions for horizontal blinds

Rules for the operation of horizontal blinds.

1. Rotation of the slats around its axis is carried out by turning the control rod.

2. Raising and lowering the canvas is carried out by a control rope. To raise the blinds, pull the rope down. To fix the blinds at the desired height, take the rope away from the center of the canvas and release.

To lower the blinds, pull the control cord toward the center, releasing the rope lock, and release the cord while holding it lightly.

Raising and lowering must be done with the slats in a horizontal position. The lower cornice can be fixed at any level.

3. Horizontal blinds are installed only indoors with relative humidity up to 70%.

4. Avoid mechanical impact on the blinds.

The lamellas can be easily deformed.

5. Horizontal aluminum blinds do not require special care products. It will be enough to regularly wash them with a soft cloth or vacuum with a brush with a soft nozzle.

For washing, it is recommended to use only cold or warm water (not boiling water and not hot water!). If heavily soiled, the blinds can be removed, placed in a bath with warm soapy water. Be careful leaving the top eaves with the control mechanism above the water. Rinse and wipe the blinds thoroughly and allow them to air dry.

6. ATTENTION! It is not allowed to repair the product by the customer.

• pencil;
• roulette;
• scissors;
• a screwdriver and a drill with a drill Ø 2 mm (you do not need a drill and a drill to install on double-sided tape).

Open the package and take out the MINI roller blind. Do not use a knife or blade to cut the package, so as not to damage the product!

Option number 1 - how to fix roller blinds WITHOUT drilling - on double-sided tape

Attach the roller blind to the window, make markings for gluing with a pencil. In order to avoid uneven winding of the fabric on the shaft, as a result of non-horizontal installation of the product, we recommend using the building level. Degrease the adhesive areas with the means available to you - apply alcohol, lighter gasoline or nail polish remover (with a solvent content) to a cotton swab and wipe well. Peel off the protective film from the adhesive tape on the upper curtain rod. Pressing firmly, glue the entire structure to the window leaf. Please note that installation on double-sided tape is suitable for products of a standard size, but is not recommended for large sizes of products (due to the large weight).

Option number 2 - how MINI roller blinds are attached to self-tapping screws

Attach the roller blind to the window, make markings with a pencil at the attachment points. In order to avoid uneven winding of the fabric on the shaft, as a result of non-horizontal installation of the product, we recommend using the building level. Screw the upper brackets to the plastic window frame with self-tapping screws. Snap the upper roller blind cornice into the brackets until a characteristic click is heard.

Option number 3 - how to install MINI roller blinds on hanging brackets

Insert the plastic hanging brackets into the slots on the top cornice. Remove the protective tape from the hinged brackets. Degrease the bonding points with any available means and remove the protective layer from the adhesive tape from the hinged brackets. Put the entire structure on the upper part of the window sash according to the markings and press firmly at the attachment points.

4647 0 0

Roller blinds for plastic windows: all about the design, methods of fastening and caring for the canvas

For several years now, a couple of windows in my house have had horizontal blinds. Everything about them suits me, except for tedious care: washing each lamella is a tedious and long task. I'm thinking of replacing them with cassette roller blinds for plastic windows.

In order not to buy a pig in a poke and not get confused when ordering, choosing the design or color of the curtains, I decided to study them in advance. If this is relevant to you, join us - we will figure it out together.

Choosing a design

Rolled curtains are called, which are a flat canvas wound on a shaft when a light opening is opened. There are no assemblies, ruffles and draperies here, the style is minimalistic.

But it is he who attracts many, as he ideally suits many modern styles in the interior, does not eat up space and does not require special care.

The question of how to choose such curtains must be approached not only from an aesthetic point of view. Of great importance is their design, and the ability of the fabric to transmit light. Well, the price, of course.

Let's start with the design features.

Cassette

There are two main cassette designs of roller blinds on the domestic market: UNI 1 and UNI 2. They have in common that the winding shaft is hidden in a cassette - a closed plastic box with guides fixed along the window frame. The edges of the fabric are tucked into them, so they fit snugly against the sash, regardless of its position.

• UNI 1 - this is a model in which the guides are installed between the glazing beads of the window frame. Its use is impossible if the glazing beads have a small height (less than 4 mm) - there will simply be nothing to fix the guides to. And if this succeeds, then the fabric sheets will stick to the glass. In addition, the glazing beads themselves reduce the area of ​​​​the luminous flux.

• UNI 2 differs from the previous model in that the guides are attached to the sash frame. They do not block the gap, keeping its dimensions, and the curtain itself is located at a distance from the glass and does not stick to it.

These designs are good because when the curtain is completely lowered, they do not let in light from the street, since the edges of the canvas are tucked into the guides. There is no gap between them and the window frame.

Cassetteless

More simple the Mini system has neither a cassette nor rails. Only a shaft and an elementary chain control system for lifting and lowering the web. If the curtain is installed on a flap, then magnets are also installed on the frame below. They keep the canvas from sagging by attracting the metal bottom bar to them.

The choice in favor of this system is often associated with the fact that it costs much less than cassette analogues, and it is easier to install it. Many do it by hand.

Standard

This option is very similar to the previous one structurally. The difference is that standard roller blinds can be installed not only on plastic windows in the opening, but also mounted on the wall or ceiling above the window.

One curtain may well cover the entire window. Unlike mini, designed for only one leaf. But since the weight of a wide canvas is much higher, and the distance between the attachment points is farther apart, the shaft in this model is made of a larger diameter.

The standard version has many advantages:

• No need to think about how to measure the correct length and width. The main thing is that the canvas closes the opening, and it can protrude beyond its limits at any distance.
• You can do without measurers, manufacturers and installers, since you can choose the size of roller blinds for your window in many stores such as Leroy Merlin and other hypermarkets with goods for home and repair. And it is always cheaper than a custom-made product.
• You can mount them on the wall, on the ceiling and even between the walls or in a doorway, turning the curtain into a door or a mobile partition for space zoning.

With two canvases

Double roller blinds are of two types:

• With two or more canvases of different types, which can be exactly one after another or offset. For example, one is transparent and the other is dense. They move up and down independently of each other, each has its own control unit.

• With two layers of fabric consisting of strips with different light transmission. They are also called "zebra" or "day-night". The control unit includes a mechanism by which these strips are displaced relative to each other. If opaque and transparent are arranged parallel to each other, an alternating striped pattern is obtained, and diffused light enters the room through the transparent areas. If the stripes are shifted so that they are staggered, you can get complete shading of the room.

How to hang such curtains, you decide - they are compatible with both cassette and cassetteless designs.

Types of paintings

To choose curtains that are practical, beautiful, suitable for your interior and meet your requirements, you need to know what materials are available for making curtains. The main parameters are the type of fabric and its ability to transmit light.

As for the color or pattern - this is already a matter of taste. There are simply no restrictions here, you can order a canvas of any shade. Monophonic, with a print, an ornament and even with a photo printing.

What fabrics are used

Such curtains should be resistant to fading, not wrinkling and not attracting dust and dirt, because they cannot be washed in the usual way.

Not many fabrics meet these requirements, therefore, for the manufacture of rolls, they most often use:

• Polyester 100%. This is the most common option due to the practicality of the fabric, which has antistatic and reflective properties, a low degree of shrinkage.

• Polyester mixed with other fibers- viscose, cotton, satin. Such combinations allow you to create an interesting structure of the canvas and achieve a more natural look.
• Screen- a fabric consisting of two-thirds of polyvinyl chloride and one-third of fiberglass. It is very durable, moisture resistant, keeps its shape perfectly - does not stretch or shrink.

• bamboo fiber. Valued for naturalness, moisture resistance, antibacterial properties. It can also be combined with other fibers for an exclusive look.

Light transmittance

Among the fabrics we offer for the production of roller blinds, you can find materials with different ability to transmit sunlight. They can be divided into 4 groups:

• Transparent are an alternative to traditional tulle. They almost do not interfere with the penetration of light from the street.

• translucent depending on the color of the fabric and its density, they create diffused lighting of varying degrees of brightness in the room.

• Semi-darkening capable of blocking up to 70% of the light that seeks to enter the house. Their professional name is dimout.

• Completely blackout or blackout - they will not let the sun's rays through at all, since they are absolutely opaque.

Mounting methods

The most familiar and logical way to install fasteners for any curtains is to drill the brackets with self-tapping screws. But it is very undesirable to “leak holes” in the frames of plastic windows, since they have sealed heat-saving chambers inside.

Therefore, the developers of roller blinds that are attached directly to the double-glazed window have come up with other installation methods that make it possible to do without drilling.

On glue

This method is mainly used for fastening lightweight mini-curtains without a cassette. Anyone can handle it.

Image	Step-by-step instruction
t	Step 1 Degrease with acetone the surface to which the landing part of the bracket will be glued. If the frame is cold, it is advisable to warm it up with a hairdryer.
	Step 2 This part is already equipped with an adhesive layer. You just need to remove the protective film from it.
	Step 3 Immediately after the release of the adhesive surface from the protection, we glue the part to the predetermined place, firmly pressing it to the surface.
	Step 4 We insert brackets into the base, to which the shaft of the roller blind will be attached.

This method has several disadvantages. The main one is the low reliability of fastening. Over time, glue or double-sided tape ceases to perform its functions. And if you need to clean the canvas, then before removing it, you will have to tear off the brackets from the frame, and then glue it again.

For hanging brackets

Plastic cap brackets are much more convenient than Velcro. And much more reliable. But they can only be used on opening or flap doors.

Image	Step-by-step instruction
	Step 1 Open the sash to release its top edge.
	Step 2 Put on the bracket.
	Step 3 Insert the product shaft into the brackets.

For clamp brackets

Such metal brackets can withstand a lot of weight, so they are used to mount heavy roller blinds. They are securely attracted to the frame with the help of a movable foot.

How to care for roller blinds

A huge plus of these products is also that the fabric is impregnated with special compounds that do not allow dirt to penetrate into the structure of the fabric. Whatever raw material it was made from. Therefore, the problem of how to wash or clean roller blinds is not the worst.

Depending on the degree of contamination, the following methods are used:

• Dry cleaning using a vacuum cleaner with a special nozzle.

• Stain removal done with a damp melamine sponge or a regular school eraser. If these do not help, you can use a natural-based stain remover that does not contain solvents. To do this, the canvas must be carefully removed, laid on a flat surface, treated with a stain, and then washed off with a damp sponge. In this case, do not rub the fabric too actively.

• Wet cleaning often needed for kitchen curtains, as grease stains, soot, traces of tea brewing or other products may appear on them. For it use neutral liquid detergents. For example, dishwashing liquid. The canvas is removed, laid horizontally and gently wiped with a sponge with a product applied to it. You can wash it off with a clean sponge or shower. The main thing is that there are no divorces left, which will be very noticeable in the light.

To prevent the product from stretching, it is better to dry it also in a horizontal position, spreading it out on a flat surface.

If the contamination is fresh and insignificant, it is quite possible to do just a damp cloth without any cleaning products.

Conclusion

In my opinion, such decor for windows is worthy of the highest praise. It is practical, beautiful, versatile. Hanging roller blinds on plastic windows without drilling is a matter of a few minutes. They save space and allow you to use the entire area of ​​​​the window sill.

Roller blinds for plastic windows- a beautiful and practical version of the sun-protection decor of plastic windows. They are a single piece of fabric, which is wound into a roll using a special mechanism.

Roller blinds are spectacular and easy to care for. They occupy a minimum of space, leaving the window sill free. And thanks to a huge number of types and shades of canvases, roller blinds will harmoniously fit into any interior.

Roller blinds can be used in conjunction with traditional curtains or as an independent window decoration. For the manufacture of sun protection structures, fabrics of various densities are used. You can simply dim the sunlight or completely darken the room. To increase wear resistance, fabrics are treated with special compounds - dust-repellent, antibacterial, water-repellent.

Our company offers roller blinds for plastic windows from the manufacturer in a rich assortment at an affordable cost:

• MINI systems without box and guides;
• Cassette roller blinds UNI for standard plastic windows;
• Cassette systems UNI 2 for windows with complex glazing beads;
• cassette roller blinds UNI 2 with spring ;
• curtains rolled Zebra MINI;
• cassette roller blinds Zebra UNI;

Roll systems for windows MINI

MINI roller blinds are optimal for small windows – they are a simple, effective and inexpensive solution. They have a small diameter shaft and are installed directly on the window sashes. They can be installed on both fixed and tilt-and-turn sashes.

The MINI system is easy to install, fastening is carried out both with and without drilling windows. However, creating the effect of complete shading in the room with the help of these curtains will not work, since daylight can seep in from the sides.

Buy roller blinds for plastic windows in Moscow cheaply.

Cassette roller blinds UNI

Cassette roller blinds UNI are a sophisticated design solution that will harmonize with the interior in any style. The design consists of a box in which there is a shaft with fabric, and two flat guides.

The box is attached to the top bead with self-tapping screws or glued with double-sided tape. The guide strips are glued to the side glazing beads of the window sash.

The price of such products is slightly higher than that of mini-options.

Cassette roller blinds UNI 2

Cassette systems UNI 2 are usually used for windows with rounded, triangular and other complex glazing beads. They are also suitable for sashes with shallow (less than 1 cm) glazing beads. The cassette and guides are placed outside the light opening, so one product can be placed on a sash with a horizontal lintel. In addition, this design prevents the fabric from sticking to the glass when it is fogged up.

Buy roller blinds for plastic windows

When the house has just been renovated, the question arises about the design of window openings. Roller blinds (roller blinds, fabric roller blinds) can be called one of the most popular modern ways of decorating a window. If you want to save a little on the services of specialists, it is quite possible to hang them yourself. Installation of roller blinds is possible with your own hands, even not for the most skilled home master. Their installation does not require complex tools or special skills. There are several options for attaching such curtains, depending on the size and shape of the window, as well as the wishes of the owners of the house to the design of window openings. The fastening method must be determined at the time of ordering, as the dimensions of future roller blinds depend on it.

Depending on the type, size of the window, as well as the design solution for the interior of the room, roller blinds are attached:

• to the wall above the window;
• to the ceiling;
• to the window opening;
• to the frame;
• to the sashes.

The first mounting method is suitable for a small window without a window sill. It will allow you to choose a long cornice, which will visually expand the opening. Mounting a curtain over a window is also good for a small room, especially if you choose blinds of the same color as the walls. In this case, the space will visually increase.

For a wide and deep window opening, fastening to the frame is more suitable. Due to this, the window sill remains freely available, and a large curtain will not focus on itself.

Types of designs of roller blinds

There are roller blinds of open and closed type. The latter are distinguished by the fact that the fabric roll is located inside a special box that performs protective and decorative functions. It is especially recommended to hang such curtains on wooden windows. For them, you can choose an option with a box made of a material that repeats the color and texture of the wood from which the window frames are made.

Cassette roller blinds

When installing closed roller blinds, vertical plastic guides are often additionally installed, which provide reliable fixation of the canvas and complete artificial darkness in the closed position. Thanks to them, the roller blind hangs parallel to the glass, regardless of how far it is lowered. You can fix the guides with double-sided tape.

How to fix roller blinds

To properly hang roller blinds with your own hands, you will need the following tools:

• level;
• drill;
• screwdriver or screwdriver.

In addition, you need to prepare a pencil, self-tapping screws or dowels (if the roller shutter will be attached to the wall), double-sided tape may come in handy.

Open type on self-tapping screws

This installation is the most reliable, but you need to remember that it will require drilling in the window profile or wall. If later you need to replace the roller blinds with ordinary ones, there will be holes.

Instructions for installing fabric roller blinds with self-tapping screws:

Closed type on self-tapping screws

Do-it-yourself fastening of a closed-type roller blind has a number of features. In addition to the brackets, you will need to fix the box and guides. You will need double sided tape for this.

Roller Blind Installation Instructions:

1. Installation of curtains should begin by removing the packaging and checking the contents.
2. Thoroughly degrease the installation site of the roller blind with white spirit, paying special attention to the mounting points of the guides.
3. Define right and left guides. Attach one of them to the glazing bead to make sure that the guide fits snugly against the line of connection of the bottom glazing bead to the window frame, unless the window design solution provides for another option. If necessary, you can shorten the guides with a dummy knife from above to keep the factory cut.
4. With a pencil, mark the top points for the location of the guides.
5. Remove the protective tape from the adhesive backing of the mounting pads of the protective box and its side covers.
6. Attach to the marks for the guides, align the box with them. Fix it lightly with the adhesive layer on the mounting pads. Unwind the fabric to a length corresponding to the height of the glass to make sure that the fabric falls freely parallel to the glazing beads.
7. Using a pencil and a level, make marks for the placement of the fasteners, and then drill for them.
8. Fasten one side of the box with a self-tapping screw and unwind the fabric again. If the canvas falls strictly parallel to the glazing beads, fix the box with two self-tapping screws on each side. Put on the side covers.
   
   
9. Remove the protective tape from the adhesive layer on the guides and stick them according to the marks made.
   
10. Carry out the steps indicated in paragraphs. See 8, 9 and 10 for installation instructions for open roller blinds.

With spring brackets

Mounting the roller shutters on spring brackets is possible only for the design of opening sashes. Such installation is good in that it preserves the integrity of the profile, as it does not require drilling.

Instructions for installing roller blinds with your own hands using spring brackets:

1. Remove the packaging, check the contents, assemble the curtain. Attach it to the sash and outline the location of the fasteners.
2. Hang the spring brackets on the sash in the marked places.
3. Slide the side covers onto the brackets.
4. Insert the curtain shaft into the mounts, unfold and fold the curtain a few times to make sure that it is level and moves up and down freely.
5. Install the lower position limiter on the chain and clamps (magnets or Velcro) for the weighting agent.

On double sided tape

This installation is suitable for the design of small doors, both deaf and opening. Thanks to him, the surface of the window profile is also not disturbed. Fastening is carried out using mounting elements with an adhesive layer on the reverse side.

The fastening of roller blinds on adhesive tape is carried out in the same order as when installing roller blinds on a spring bracket. The only difference is that the reliability of fastening will need to first degrease the surface at the places where the fasteners are glued. This installation method is not recommended for large roller blinds, as it does not provide sufficient fixing security.

In contact with