We make a beautiful and strong country table with our own hands. How to make a coffee table with your own hands How to make a table

Making furniture with your own hands is not only a great way to save money, but also an opportunity to put your creativity into practice!

It's about making coffee tables with your own hands. Too many side tables do not happen. They can be placed next to the sofa to place a vase of flowers or a mug of tea, used as a bedside table or as a stand for houseplant pots. However, monotonous wooden tables are unlikely to revive a dull interior. I want something stylish and unexpected ...

Stylish do-it-yourself table made of wooden slats

This bench can serve as a coffee table, extra seating, or space for houseplants. Such a piece of furniture will “fit” well into almost any interior!

DIY coffee table photo

Materials:

Tools:

Step one: Using a hacksaw, cut the ends of two 2.5x7.5cm boards at a 45 degree angle. Cut out fragments from 2.5 × 5 cm bars, the length of which will correspond to the internal length of 2.5 × 7.5 cm blanks.

how to make a coffee table with your own hands. A photo

step two: Place 2.5x5cm blanks in the middle and 2.5x7.5cm around the edges. Make sure the ends of the inner rails are aligned.

Step Three: Measure the distance between the outermost 2.5x7.5cm boards and cut two blanks of this length from 2.5x10cm boards. They will serve as the lower supports for the bench. Secure them by screwing self-tapping screws into each longitudinal rail.

Step Four: Using the Kreg Jig, drill two pocket holes at each end of the support rails. These holes will be used to connect to the 2.5x7.5cm end pieces.

Tip: It's hard to give specific recommendations on how far from the edge to attach the Kreg Jig. This depends on the length of the screws used, the exact thickness of the board, etc. We advise you to pre-practice on unnecessary scraps of boards.

unusual coffee table with your own hands. A photo

Step five: Place 2.5x7.5 cm blanks along the edges of the structure. After making sure that their ends are at the same level, fix them with clamps.

Tip: If you are using softwood (such as pine) to make the table, place unnecessary scraps of boards under the clamp supports. Otherwise, traces of clamps will remain on the wood.

Step six: Securely attach the 2.5x7.5cm end pieces to the base of the bench by driving 3.5cm wood screws into the countersunk holes you made at the ends of the support rails earlier.

wooden coffee table. Master Class

step seven: Measure the width of the finished base to determine how long you need to cut 2.5 × 7.5 cm blanks for the ends of the bench. We recommend that you take a sip with a small margin in length, and then take your time to grind off the excess until you achieve the perfect fit.

Step eight: Moisten the ends of all rails with water and apply a small amount of Gorilla Glue.

Step nine: Install the end boards in their intended place and wrap the entire structure with a belt so that it does not fall apart until the glue dries. For reliability, you can additionally fix the ends with a few finishing nails.

Step ten: Sand the surface of the bench with 120 grit sandpaper to eliminate any unevenness at the joints. All gaps in the seams and recesses from the heads of nails (the latter must be recessed into the wood without fail) fill with putty. When the putty is dry, sand the surface again, this time with 220 grit sandpaper.

Step Eleven: Paint the bench. We advise you to sand the surface again before painting with 400 grit sandpaper and water.

Step twelve: On the lower support rails, fit the special mounting plates for attaching the legs. When fixing them, make sure that you drill holes in places where there are no already screwed screws. The distance from the mount to the edge of the bench base should be about 2.5 cm. Screw the legs themselves into the mounts.

Coffee table made of copper pipes. Master Class

The material for the manufacture of the next table can, perhaps, be called the most unexpected. This time we decided to tell you how to make a table out of ... copper tubes with your own hands.

Materials and tools:

The figure below shows all parts (pipes (A-E) and various fittings (F-H)) with their dimensions and quantities. All that's left for you to take pipe cutter and sit in front of the TV, which will brighten up the tedious cutting process a little. It's not hard, just a little boring. 😉

When all the blanks are ready, you can begin to assemble the lower part of the table. How to do this is shown in the figure.

Having collected the lower tier, you can proceed to the upper one. The only part not listed in the parts list are four pieces of 2.5 cm pipe that are placed in tees at the top of the corner posts. Without these inserts, you will not be able to put on decorative caps, because. the latter have the same diameter as the tees.

Reliable connection of the tubes to each other will ensure glue, but we recommend applying it only after the preliminary assembly of the structure, i.e. after you make sure that all the cut tubes are of the right length and fit well with each other.

Wooden shelves, which you can pre-paint if you wish, are fixed with special clamps that are placed on the underside of each board. Now you are ready to decorate your home with your new DIY table!

DIY lightweight cement table

Concrete countertops and other interior elements have recently become more and more popular. However, for all their attractiveness, they are not without a number of shortcomings. First, pouring large amounts of concrete can sometimes be quite expensive. Secondly, if we are talking about small side tables, another serious problem comes to light - such furniture turns out to be too heavy. On the one hand, there is a desire to get a good, solid thing, on the other hand, I want to be able to move a table made by myself without the help of professional movers. The found solution can be considered an insight.

Materials and tools:

Step one: Mark and cut the foam sheet. From a 120x240 cm piece, you can cut 18 squares 40x40 cm. Stacking them on top of each other, you get a 40x40x45 cm box.

do-it-yourself foam board. A photo

step two: Glue the cut pieces. 3M Super 77 spray adhesive is ideal for this. It is best to perform this stage of work outdoors. Don't forget to wear gloves and a long sleeve shirt. Apply an even layer of glue to one side of the first square, then do the same with the second. Wait ~15 seconds, then connect the squares, making sure their edges are joined. Repeat this until all the square blanks are connected into a single whole. Wait about 30 minutes before proceeding to step 3.

Step Three: Now the most interesting thing ... giving the resulting parallelepiped the outlines of the future table. We decided to make a table in the shape of a cylinder. You can come up with something more original or, on the contrary, keep the original block with right angles. Cutting foam is easy and fun. At first, your design will have a rough, angular look, but don't worry! After the table has been given the desired shape, it will be time for grinding. Using sandpaper 36 grit will quickly smooth out any bumps. As you get closer to the ideal, gradually move to sandpaper with a finer grit size. Don't aim for a super-smooth surface, at this stage it's just a matter of getting the desired shape.

Step four: The surface of the future table is polished, it is time to cement it. The first coat, applied throughout the foam mold, will fill in the voids and texture of the foam. You only have ~20 minutes, so act fast so you have time to iron out the bumps. When the applied cement mortar dries, you can apply the next layer. The number of layers depends on how smooth and even the surface you want to have in the final (as a rule, four to five layers are required). It should be remembered that the smoother the surface of the final layer before it dries, the less it will have to be sanded!

Tip: When preparing cement mortar, follow the manufacturer's instructions. You should not prepare more mortar than you need to apply one layer (for example, we used 220 ml of water and 450 g of cement). Make sure you don't forget to cover your workbench or workshop floor as this is a messy job.

Step five: After the last layer of cement has dried, you can sand the surface if desired. We wanted to achieve a glossy finish, at least on the top of the table, so we sanded it down using a variety of grit sandpaper ranging from 100 to 2000.

Tip: If you are planning this operation, get a protective mask that will help you protect your lungs from cement dust.

(The table made in this project turned out to be very strong and strong, but at the same time it weighed no more than a kilogram.)

Do-it-yourself stump table

The material for the next table sometimes literally lies underfoot. Even residents of megacities, if desired, will be able to find a suitable stump.

log table. A photo

Materials and tools:

• wooden block;
• white acrylic paint;
• manual grinder;
• chisel;
• a hammer;
• decorative upholstery nails;
• molar tape.

Step one: Find a table base! This should not be an old rotten stump, but a freshly sawn block of wood. Let it dry for at least 6 months (there's nothing worse than waiting, but it's necessary) until the bark begins to peel off the trunk.

Step two: Using a chisel, gently remove the bark from the log in a downward motion. If the stump is dry enough, you won't have to use too much force.

Step three: Using a sander with medium grit sandpaper, sand the surface, removing the remaining bark and smoothing out sharp corners. Do not forget to sand the surfaces of the lower and upper cuts. Wipe the wood with a damp cloth.

Step Four: It's time for painting. We used a white semi-gloss paint that includes a primer (we needed three coats for full coverage). You can choose a different type and color of paint, focusing solely on your taste. Don't forget to pre-prime the surface of the wood. Make sure you don't forget to finish the bottom cut.

Step five: Get your decorative nails ready. Apply a strip of masking tape along the top edge of the side surface of the block of wood, thereby marking the place where the first row of nails will be located.

Step Six: Using a hammer, drive in the first row of decorative nails. To ensure that the distance from them to the upper edge is the same throughout the entire length of the “line” of nails, use the strip of masking tape you previously glued as a guide. After the first row is completed, repeat the same with the second and third row of nails (we needed almost 150 studs for three rows).

Tip: Cover the underside of the stump with furniture felt so you can move the table around the room without damaging the flooring.

The work is done. You can use the new piece of furniture and be proud that you made this charming coffee table with your own hands.

Coffee tables: do it yourself

Wooden table: how to make?

Many people are interested in how to make a wooden table with their own hands to get a model with an original appearance. Let's consider one of the options.

To make an original coffee table with your own hands, you should take beam with a section of 5x10cm. It is sawn into parts of the following length: 130cm - 9pcs, 21cm - 12pcs, 34cm - 2pcs.

The prepared beam is placed in three rows, leaving room for attaching the legs.

Remove the top two rows. The timber in the third row is slightly shifted to get an interesting appearance. Next, mark the places for attaching the transverse parts.

Lay the extreme bars of the second row and mark the places of the cuts. Then cuts are made circular saw or a hacksaw with a chisel.

The bars of the second row are fixed with screws.

The third row is laid, the parts are shifted and fixed.

An empty space is formed under the tabletop, in which they are fixed legs.

Wood is processed protective composition that preserves the grain of the wood.

The original model of a wooden coffee table with their own hands

First, to make a table with your own hands, prepare boards: 6pcs - 22.5x45cm, 2pcs - 22.5x41cm, 8pcs - 20x4cm, 8pcs - 40x4cm.

Planks 20x4 and 40x4 are glued in pairs. To ensure they are securely glued, they are clampedclamps.

While the blanks for the legs dry, collect box from the rest of the details. They are connected with carpentry glue and nailer.

legs attached to the box with countersunk screws. At the bottom between the legs put the crossbars.

Lid for a table made of wood is also made using boards 22.5x45cm. They are glued together, and then the resulting square is sawn into two triangles.

One triangle is fixed with screws, and rails are fixed on the second so that it is removable.

All parts are sanded and painted.

Stylish coffee table. Master Class

They start making a stylish table with their own hands from marking the sheet Chipboard 16mm thick. The center is found on the sheet at the intersection of two diagonals.

A nail is driven into the center, to which a thin rope or a harsh thread is tied.

Tie a pencil to the free end. This allows you to draw a circle.

If you want to make a table with your own hands not round, but more interesting, then the shape of the circle is changed by drawing bends.

The tabletop is cut out jigsaw or reciprocating saw.

Edges are processed sandpaper.

legs fasten with screws. If they are inclined, then the slope should be outward.

Table surface stain in the right color.

Simple shape coffee table

To make a coffee table with your own hands, take boards 40x15cm - 2pcs and 50x19cm - 2pcs. In addition, you will need legs and mounting plates.

On one of the boards they fix more plates for fixing legs. From the edges should retreat a little.

The sides and top of the table are fixed with wood glue.

It dries for about half an hour.

Do-it-yourself log table

A do-it-yourself coffee table with such an appearance will become a decoration for a summer house or a country house. Begin work with the assembly of the frame. To do this, take sheets plywood two centimeters thick. A base with dimensions of 60x80cm is cut out of them. A box 68 cm long, 45 cm wide and 40 cm high is attached to the base.

do-it-yourself log table. A photo

After that, cut thirty pieces of round logs 45 cm long and twenty-four round cuts, the thickness of which is 3 cm.

Harvested logs are attached around the perimeter of the box. Attached from below to the base rollers. They are installed, departing from the edge by three centimeters.

In addition to glue, it will be useful to fix the logs on the screws from below.

Installed on the box plywood cover. Rounds are glued on it. The space between them is filled with wood putty, which does not shrink when dried. Apply it in stages so that the previous layer has time to dry.

After the putty has dried, the surface polished. To do this, use a surface grinder. After that, the log table can be used.

Rustic table

If you are interested in how to make a table from wood cuts with your own hands, then you should read the instructions.

They start making such a coffee table with their own hands by choosing the right material.

Selected saw cut inspect for interesting details or parts that need to be removed.

Unnecessarily rough, protruding parts are cut off. On the side where the countertop will be, the surface align.

For work use cleaver, which moves at an angle of forty-five degrees.

The sides also need to be aligned.

All surfaces grind, using ever-decreasing grit.

Glossy varnish mixed with resin in equal proportions.

The resulting composition is applied to the wood in a thick layer. It will dry for a long time. If gaps appear during the drying process, they must be filled.

bottom side clean up. If there are voids in the tree, then they are filled with resin gradually until the hole is filled.

If there are air bubbles in the dried resin, then the surface is heated with a heat gun or burner.

A second layer of resin is applied and again left to dry for two days. The entire surface of the countertop must be glossy.

At the handles of the ax, a part is cut off at an angle of 22 degrees. The surface is sanded and painted in the desired color.

Mark out places for legs and make holes.

Glue is poured into the holes and the legs are installed. Each has a special pad.

White coffee table

They make such a coffee table with their own hands from plywood and glass. First, prepare a drawing and determine the dimensions. Then proceed directly to manufacturing.

handmade coffee table Blueprints

Plywood acts as a countertop box with partitions, covered with glass on top. Triangular legs are attached to it.

At the box, you can make a door to access what's inside, or raise the glass.

legsfor a table with your own hands, it is better to cut it out of fairly thick plywood. It must be remembered that double legs are easier to make than more single ones.

When all the parts are ready, they are assembled together and fastened. The table is painted or varnished.

DIY pallet table

If you know how to make a table from pallets with your own hands, you can get an interesting version of furniture for the home. Pallets must first be sanded, sawn into pieces and primed.

pallet table. Instruction

A table is assembled from the prepared material. To do this, attach the legs or wheels. The pallet itself or the surface assembled from individual boards can be used as a table cover.

After all the parts are connected, the structure needs to be painted or varnished. After that, the pallet table is ready.

The second version of the table from pallets

To make such a table with your own hands, you will need one or two pallets. First, you should draw a sketch of the future product, taking into account all sizes.

The table will have a shelf for small things under the tabletop. The design is assembled from prepared parts.

The surface is painted with black paint, but this is not the only possible option. There are many other decorating options.

Coffee table stand

How to make a table out of copper pipes with their own hands, may be of interest to many craftsmen.

Pipes are first marked and cut. Then they are smeared epoxy glue and assemble the base for the table.

This base is applied to the board and the attachment points are circled. In these places you will need to drill holes by pipe diameter.

Four holes are drilled, but not through.

The board is impregnated polyurethane and cover stain.

The rest is collected from the pipes frame.

Legs and base cover paint in the color of the tabletop.

Made from a piece of cloth pocket, which is hung on the transverse parts of the legs.

All parts are assembled together, adding epoxy glue for reliability.

DIY marine-style table

Such a table from the old window frame looks very romantic. The frame is cleaned of dust. If required, replace the glass.

wooden surface stain white acrylic paint. After drying, the paint layer is treated with sandpaper so that the wood comes out. Also available in blue and white.

To make legs, take cutting and sawn into pieces of 34 cm. After that, it is treated with sandpaper to remove roughness.

The blanks are drilled in four places. Next, each leg is attached to the base, and the base with legs to the frame. All this is done with self-tapping screws.

The legs are covered with coarse rope.

For cleaned and defatted glass glue sea souvenirs and seafood. From above they must be covered with glass, which is cut out in the workshop to fit the frame.

Make a loop at one end of the rope. The rope is glued around the perimeter of the frame, leaving the loop free. When the second end reaches it, they tie an interesting sea knot.

The table is the second item after the stool that every novice furniture maker should be able to do. The table can be created from different materials and have unique characteristics. A great intention for you will be the desire to make your product out of wood.

A wooden table is fairly easy to create with your own hands, it is enough to have minimal skills in working with carpentry tools. And the cost of the material will be significantly less than a table using metal, glass or plastic.

A piece of furniture made by oneself will correspond as closely as possible to the desires of a happy owner, and will please the eye incomparably more than the purchased one. And most importantly, when creating a table with your own hands, important skills are acquired in working with the material, which will make the restoration of operational defects much easier.

What makes a good table

A particularly beautiful countertop can be made from cheap non-grade pine boards, knotty and serrated (without falling knots, rot, fungus, wormholes), which, when well processed, give a wonderful pattern, to achieve which, when working with expensive wood, much more effort and effort must be applied .

When choosing a material, it is important to take care of the strength of the future product. To do this, pay attention to the density of wood.

Soft (spruce, pine, chestnut, dogwood) is easily damaged during operation, which adversely affects the durability of the table. But scratches and dents can be hidden, although the restoration process will be quite frequent.

Hard woods (beech, ash, maple, oak, walnut, fruit woods, elm) are quite difficult to handle on their own. And you may have to look for masters to work with them. But ensure the durability of the product.

External characteristics

It is very important to determine in advance for yourself the appearance of your future product. The main rule of a good table is if the design fits well into the space allotted for it and leaves a lot of free space for those sitting.

It is also important to consider that a table with a rectangular top will accommodate fewer people than a table with a round or oval shape with the same area. And it would be more expedient to make a table for guests in a folding version, which unfolds for big holidays, and is folded in everyday life. Also, such a folding table will be convenient in the backyard.

Most often it is required to choose a kitchen table. It should be roomy and pleasing to the eye, to facilitate the process of working with him. But it should not interfere with movements in the room and in no way interfere with the process of culinary creativity.

Based on this, it is absolutely clear that the size of the table is selected depending on the area of ​​\u200b\u200bthe room. Also, softwoods cannot be used for the kitchen table due to its use in "extreme" conditions.

The choice of the external characteristics of the product is a responsible process, therefore, before starting the formation of a table for a dacha with your own hands, it is extremely necessary to carefully assess the needs for which this table is being made.

Transferring ideas to paper

When creating a design that is the fruit of your imagination, you will have to develop a diagram and drawings of your table with your own hands. Why there is a huge variety of electronic programs.

After a thorough development process, it is extremely important to transfer the result to paper. For fast and high-quality work, it is very important to use this manual constantly.

creative process

Preparation of drawings is the last preparatory stage. Next, you can proceed to the most important part of the work - the manufacture of parts. Do-it-yourself wooden tables are created much easier if the drawings and diagrams are as informative as possible. This reduces the chance of errors to a minimum.

You can personally make it as a desk, as well as a coffee or children's version. With a certain skill, it is possible to create a computer desk. As well as a dining or country model. Each of the options is quite easy to implement.

The canvas for the countertop and the board with the bars, from which the rest of the parts will be formed, are processed with the available tool or, at worst, coarse-grained sandpaper to remove defects present in the form of bumps and protruding knots.

Boards are sanded from all sides, including side edges and corners. If you are creating a canvas from wood cuts, you need to make sure that they are dry enough, and also close up small cracks found after visual inspection. And it's better to screw them. To get a more reliable grip of the canvas and save time on assembling the elements.

Transfer the scheme to the finished canvas. The main elements are cut with an electric jigsaw and, if necessary, the sections are ground. The protruding support elements are cut off by about 3 centimeters. Horizontal cuts are made on both sides of the supports (legs).

The blanks are covered with a preparation that prevents the ingress of moisture and pests, and only after the final drying is it allowed to resume the process of creating the table with your own hands.

Putting the details together

After making all the necessary details, you can begin the sacred rite. Namely, to collect the desired masterpiece together. And it can be either a round table or any other selected product.

First you need to assemble the support structure with screws and glue (first, thin channels are drilled with a drill for the length of the screw, otherwise there is a chance of splitting the part). Galvanized screws can be used for connection, as they do not rust, and this is very important for wood products. Or wood glue.

According to the basic rules, the frame in length and width should be 30-25 cm less than the countertop.

From the sides you need to attach additional boards to stiffen and hide the place where the legs are attached. Cut off the chamfers in the places where the legs are installed.

Then the table leg is fastened in place with clamps, and holes for the bolts are drilled into the frame. Install the support elements in their places and fix them with stoppers. Strengthen the structure with wood glue. Then install the countertop in place for which furniture corners are used. At the very end, all visible screws are hidden with wood-colored plugs.

The final stage. Finishing

A photo of the completed table can be seen below. Achieving this result is surprisingly easy. Optionally, you can round either only the corners or the entire end, depending on the type of table. It will be nice to make chamfers on the edges of the tabletop.

Roughnesses are polished in the entire structure, with the help of putty, mistakes are hidden. To extend the life of a table assembled by oneself, it is necessary to cover it with several layers of varnish or stain.

Thus, making a beautiful wooden table with your own hands is a fairly simple leisure activity. And easy to do. The guarantee of extracting a solid, ideal in terms of dimensions and aesthetic result according to your drawings is: strict adherence to the instructions, error-free execution and carefully selected material. And the resulting table will harmoniously fit into the exterior.

DIY table photo

Coffee table - at first glance, not the most necessary furniture. Therefore, its acquisition is endlessly delayed. But it is precisely such items that make the interior truly cozy and comfortable. Therefore, we share ideas that will tell you how to make a stylish coffee table with your own hands and not go broke.

1. Democratic and accessible

To make such a table, you will need a pair of metal or plastic boxes and two large boards. Be sure to securely fasten the structure.

2. For the smartest

Books with beautiful covers and a small glass for the tabletop - that's all the materials for such a coffee table. Books must be glued together, and the glass can be fixed on them with silicone glue, which becomes transparent after drying.

3. Ordered chaos

A coffee table made of flat elements fastened together in a chaotic manner is an idea that is easy to implement. Wooden saw cuts, parts of boards, large books are suitable.

4. Industrial style

A reel for industrial cables is a thing that cannot be found on every corner. But if you are still lucky enough to become the owner of this item, you can make an excellent coffee table out of it.

5. Table for motorists

A coffee table made from a car tire will last for many years. But it is desirable to use the tire without damage. It remains only to paint it, fix the countertop and legs.

6. Wooden table almost free

Ordinary pallets, which can be purchased for a penny, are an excellent material for making furniture. A little imagination, and the wooden coffee table is ready.

7. The second life of old boxes

Another way to become the owner of a coffee table made of natural wood is to use old boxes as a material for its manufacture. Four large drawers fastened together form a stylish table.

8. Extravagant chic

Especially original, but at the same time luxurious, looks like a coffee table on asymmetrical legs. The tabletop is made of a thick board or a wooden saw cut.

9. From the cottage - to the living room

A large wooden barrel easily turns into a coffee table. It must be cut into two parts, and then attach the countertop and legs to one of them.

10. Roomy and functional table out of the box

A household box made of plastic or wood can also be used as a coffee table. In order for the table to be mobile, you can fix small wheels on its bottom.

11. Warm table

An old heating radiator is a reliable basis that will help you make a coffee table with your own hands. You just need to paint it in the desired color, attach the wheels and put thick glass on top.

12. From the interior door

An interior door that has served its time becomes a material for making a coffee table with your own hands. It must be cut into several parts and fastened together.

13. If it’s a pity to quit and it’s hard to carry

An old suitcase can become an original coffee table top. You just need to attach legs to it.

14. Brutal elegance

An affordable option for making legs for a coffee table is ordinary plastic or metal pipes connected by fittings. Such furniture will perfectly fit into the interior in loft style.

15. From an ordinary wooden beam

A wooden beam, folded in a checkerboard pattern, will become a countertop for a homemade coffee table. Legs can be made of thick metal wire.

To make the interior look harmonious, it is necessary to take care not only of the details, but also of the decoration of the room. Continuing the theme -

Do you love designer clothes, but sigh in frustration when you look at the price tags that adorn them in stores? Try to become a designer yourself. Think it's difficult? Nothing like this! By following the instructions, you can easily create do it yourself original a piece of interior from improvised materials. And we propose to start with coffee table- such a simple, but very important subject furniture. Believe me, at such a table you will be happy to give tea to your guests, who will admire your skills. In addition, by creating a coffee table with your own hands, you will literally fill your house warmth and put a piece of your soul into it. So it's definitely worth a try.

DIY coffee table in a marine style

Romantic idea. All year round, drinking your favorite drink at this table, you will remember the warm sea, the gentle surf and the moonlit path. " Nautical» a table is tenderness, sophistication and originality in the heart of your home.

How to do?

1. Take an old window frame and clean it of dust and dirt. If the former glass cracked, insert a new one, then get rid of the layer of the old paints and sand the surface. Next, you should remove the metal corners, which additionally fix the details. frames.

Ready! Enjoy your creation and give joy to your guests!

Table-suitcase for travel lovers

A very original solution for an old favorite suitcase that has seen other lands with you and that you don’t want to throw away because of the memories.

How to do?

To get started, go to the store where you will need to purchase furniture legs ( wooden or metal). If you want to make a mobile table - then you need to take the wheels. You will also need plywood, screws and a screwdriver.

Now we make markings on the bottom of the suitcase for future legs and drill holes. Since it will not work to attach the legs to the fabric, we put plywood inside the suitcase, make markings on it through the holes and also drill it. Now we attach the mount to the bottom of the suitcase and fasten the legs. Using hot glue, glue the felt inside the suitcase.

To give the table an original look, reminiscent of distant travels, you can decorate it with stickers made in the form of stamps, or decorate it at your discretion.

That's all - an unusual coffee table is ready! By the way, there are a lot of options for turning suitcases into tables: by choosing the legs to your liking, you can make a table in style retro or classical. You can not attach the legs at all if you have a massive suitcase - it will look truly incredible: such a table will bring a sense of adventure and adventure into the interior, the spirit of travel and unexplored distant countries.

Log table for nature lovers

We take wooden bars (in this case, birch) of the same height and width, only 32 pieces. You also need to take the base for the table, legs (4 pieces), putty to match the wood, a screwdriver and glue designed for wooden surfaces.

First you need to assemble the base for the table, then glue wooden bars around the perimeter, and sew up the middle with cardboard. Then we fasten the legs to the bottom. Next, we glue thin wooden dies to the inner surface - thanks to this, it will seem that the table is completely wooden. Now we take the putty and carefully close up all the voids, after which we overwrite until an absolutely flat surface is created. Voila! Now you are the owner of an extraordinary table that will become the highlight of your interior.

If you like the idea, you can create other tables according to this scheme, using, for example, branches instead of bars. To create such a table, you need to take a plywood box, painted black paint, the size of which is 40x40x60 cm (or any other size at your discretion).

To glue the frame, we take branches, from which we first remove the loosely holding bark (we do this with sandpaper). What is the procedure for gluing: first we glue the branches on the long side of the table, and then we select wooden dies and, as mosaic, lay them out on the ends. The thickness of the dies should be approximately 1 cm, they can be cut with a parquet or circular saw. And finally - install the glass, which will be the countertop. If desired, by screwing wheel supports to the table, it can be made mobile.

Using the same technology, you can create many more unusual pieces of furniture. You can lay out the branches horizontally and then you get such a wonderful table. Such furniture looks not only very original, but also incredibly stylish.

original pallet table

An idea that came to the mind of someone truly brilliant. It would seem that you can come up with pallets, which are probably lying around in every dacha? And you can make them a very convenient and functional element of the interior.

How to do?

To get started, collect all the tools you need for your idea: the pallet itself, a drill, clamps, a hammer, screws, a nail puller, glue designed for wood, wheels, soap, a primer, a screwdriver. In addition, take paint brushes, a petal brush head with abrasive bristles for a drill, varnish and a colorless primer.

First of all, you should take a drill with a nozzle designed for wood processing, and clean the surface of the boards from contamination with it. Now carefully disassemble the sanded pallet into parts. Lightly tap the rusty nails with a large hammer and carefully pull them out with a nail puller. Glue the broken pieces of boards with wood glue. At this stage you will need clamps. They need to carefully clamp the boards and wait until they dry out.

Now the parts prepared for the countertop need to be nailed and glued on the reverse side, then clamped with clamps and wait until they dry.

Then cover the table with a colorless primer, and then varnish. Next, on the back of the table, mark the places for the screws to attach the wheels. Drill holes for the fasteners. In order for the screws to easily enter the wood, grease them with soap. Using a ratchet, you can quickly and conveniently tighten hex screws.

Stylish, compact and quite functional table is ready!

Table from boxes

Another original idea captivates with its simplicity and surprise - well, who would have thought to build a table from boxes? But it has come, and now you yourself can create such an unusual piece of furniture at home. Surely you yourself will be delighted, and your guests will appreciate the originality of this idea.

How to do?

Take 4 wooden boxes, sandpaper, water-based varnish, roller and brush, dowels, 10 mm plywood sheet, PVA glue, 4 wheels and self-tapping screws.

First you need to sand the boxes and varnish them. Then, using a drill with an emphasis, make holes at the ends of the boxes. Using wood glue, you need to fix the dowels in the attachment points and connect the ends of the boxes to each other. Attach the wheels to the plywood sheet, and then attach the sheet to the boxes with self-tapping screws. The table is ready!

These extraordinary things can be created from quite ordinary materials. Having imagination and a desire for originality and comfort in your home, you can easily work wonders. Look around: maybe the old window frame has every chance to turn into an interesting element of the interior?

Or maybe a huge wooden reel from an industrial cable that can become an elegant piece of furniture?

Regardless of the size of the kitchen, whether it is a spacious kitchen in a new building, a country house or a small one in a small family, the most important piece of furniture is the kitchen table. Various building materials are used today for the production of tables, for example, glass, metal, stone, plastic, wood. But of all these materials, wood is still used more often. If you want to save money, then the kitchen table can be made independently. In this scenario, you can save up to 70% of the cost of the table. But first you should work hard and take into account a large number of factors that we will consider together with you in this article.

Making important measurements and calculations

Before starting work on the manufacture of the kitchen table, it is important to make some calculations. Usually such tables are calculated for a specific number of people. As a rule, this number ranges from three to nine. But it is best to take into account a couple of extra places in the calculations, in case guests arrive. If you are hospitable hosts, then most likely you will need a large table that can accommodate up to fifteen people.

Important calculations:

• The working length for one person should be 60 cm. This figure is multiplied by the number of people. The resulting figure will be the perimeter of the future table.
• How exactly the table will be installed: in the middle of the kitchen, near the wall. In the first version, the table will be able to accommodate more guests.
• Will the table have drawers or other accessories.

Decide on the size and location. The optimal table width is 80-110 cm. If a narrower table is planned, then you will have difficulty serving. In the case of choosing an oval table shape, it is necessary to calculate the circumference. To do this, multiply the square of the radius by the number Pi (3.14).

Round or oval kitchen tables are necessarily located only in the center of the kitchen.

• Do not place the table near the stove.
• You can not put a table under the air conditioner.

It is equally important to decide on the shape of the table. Surface geometry can drastically change the look of an entire space. It directly depends on the shape whether it will be convenient to eat or not. Most of all, a rectangular shape with right angles is in demand. These countertops are great for square or rectangular kitchens. At the same time, it can be placed near the wall or in the center of the room.

Oval-shaped tables are also very popular. There are several valid reasons:

1. The oval table has an attractive appearance.
2. There is no need to go around corners. This is especially convenient when there are small children in the house.
3. An oval table is best suited for a formal meal.

There are a lot of advantages in favor of an oval shaped kitchen table. But in the presence of a large family, it is inferior to a rectangular shape. There are also round shapes, but with this option it will be inconvenient to take certain dishes. As for the oval table top, the ideal diameter is 140 cm.

So, when choosing the shape of the table, start mainly from your own taste. Moreover, remember that for a kitchen of 8 m 2 or less, an oval table will be impractical, as it will require a lot of free space.

We prepare drawings and tools

If you have decided on the size and shape of the kitchen table, then you can proceed to the next step - drawing up a drawing. It should display the required dimensions of the surface, legs and other elements. You should consider the method of fastening certain nodes. Consider, for example, a kitchen table that will have the following dimensions: 120x60x75.

Although such a table will be small, you can easily understand the principle of making such furniture using its example. In your drawing, you can resize the table according to your needs.

You will need:

1. Tabletop 1.2 × 0.6 m - 1 piece.
2. Cross jumpers 40 × 2.5 cm - 2 pieces.
3. Longitudinal jumpers 100 × 2.5 cm - 2 pieces.
4. Table legs 70 cm high - 4 pieces.

To build a countertop, you need to prepare boards of the appropriate size. Before starting work, you will need to consider the method of attaching important nodes.

First of all, you will need to collect all the necessary tools and materials:

• plane,
• hacksaw,
• electric jigsaw,
• screwdriver,
• sandpaper,
• ruler or tape measure
• square,
• pencil,
• circular saw,
• milling machine,
• file,
• clamps,
• paint brush,
• wood glue,
• polyurethane varnish: matt or glossy,
• solvent.

When everything is ready, you can get to work.

Assembly Guide: Countertop Requirements

As for the countertop, it is important to decide whether it will be sliding or not. For example, when assembled, the table can be used for cooking, and in a sliding state as a means for eating.

The countertop should not absorb odors and grease. Also consider practicality.

A good countertop should not absorb moisture, withstand strong impacts. The surface of the table should not be afraid of steam, condensate and high temperature. All these requirements are met by a countertop made of natural and artificial stone or covered with ceramic tiles. But it should be noted that such a table will look only in the interior of modern style.

One of the most common types of countertops is chipboard, laminated with film or covered with plastic. At the price of chipboard plates are available to many. Moreover, such material is the easiest to work with. Some may deny that chipboard countertops are practical. This is partly true, but with proper processing, it will last more than one year. Here are some recommendations and tips for working with chipboard countertops:

• The film or plastic should be rounded at the ends of the chipboard.
• Each 90° rounded end is treated with silicone.
• However, in this position, the end is vulnerable to moisture ingress, so it is better to wrap the end 180 °.

You should be objective and mention the disadvantages of such a countertop. If the chipboard swells, then there is no way to fix this problem. As a result, you will have to make a new table or at least a countertop. But, on the other hand, such a surface is resistant to aggressive detergents and mechanical stress.

Of course, if we talk about the most ideal and environmentally friendly option, then here the tree rightfully comes first. But in the care of such a surface is more capricious. Do not allow moisture to penetrate into the wood, allow scratches and other damage. Microbes can settle and multiply inside them, which adversely affect the mechanical strength of wood. Therefore, from time to time, wood countertops must be varnished, cleaned, and opened with a layer of wax.

leg requirements

The number of legs will vary depending on the shape and size of the table. For example, if you are making a table from chipboard, then 4 legs will be enough, which are attached to the corners of the tabletop. If you make strong wooden legs, then this design will be durable and strong.

Legs can be made by hand. To do this, you can purchase a ready-made sketch. The complexity of this work will depend entirely on the shape of the legs. If you think that this is beyond your power, then purchase ready-made metal legs or choose carved wooden ones. Everything will depend on your financial capabilities.

The table can be on one leg. As mentioned above, this will depend directly on the weight, shape and configuration of the countertop and the table as a whole.

The table, which has one massive leg, looks impressive and beautiful from the side. For its installation, a high-quality cruciform strapping is performed.

Two massive legs are located at a certain distance from each other. In most cases, a table with two legs is rectangular or oval. The advantage of such structures is that the legs will not interfere with any of the sitting people. As for the design of such legs, they expand at the bottom to increase the area of ​​\u200b\u200bsupport. Between themselves, they are connected by a jumper board.

But ordinary tables with four legs are simple in design and do not need precise and complex calculations. This table is stable and durable. The most important thing here is to choose the right size of the legs and mount them at the right distance. At the same time, tables on four legs can be very different in shape: oval, round, square, rectangular.

So, regardless of the number of legs chosen in your design, their aesthetics always remain the most important. The aesthetic appeal of the table legs is even more important than the beauty of the countertop. After all, the tabletop is always covered with a tablecloth or oilcloth, and the legs are always visible.

We build a folding table

One of the simple shapes of the kitchen table is rectangular. This design consists of four legs and six sidewalls of the box. The table top and sidewalls can be made from 18 mm chipboard, and the legs from a 40 × 40 mm bar. First you need to make plywood drawers, 2 cm thick (table legs will be attached to them), as well as two horizontal strips. It is on them that the removable part of the table will be placed. In our case, for the manufacture you will need to purchase the following material:

• Self-tapping screws 4×16.
• Self-tapping screws 4×50.
• Furniture corners 30×30.
• Laminated edges in the color of chipboard.
• Wooden dowels 8×40.

To make the table move apart, you can use standard guides. They provide smooth movement of the countertop. So, all the necessary parts of the following sizes are pre-made:

• Leg 710 mm.
• Two fixed parts 450×700 mm.
• Removable part 400×700 mm.
• For the box of the fixed part, there are four sidewalls 420 × 120 mm.
• For the box for fixed parts, two end 600 × 120 mm.
• From plywood, two side drawers 830 × 120 mm.
• From plywood, two end sides 498 × 120 mm.
• To accommodate a removable tabletop, two strips 498 × 120 mm.

With such blanks, you get a sliding table in size:

1. Extended 1300×700 mm.
2. Assembled 900×700 mm.

It is best to cut all the blanks on special equipment. This is important in order to accurately withstand all dimensions. All blanks made of plywood and wood should be carefully cleaned and varnished in two layers.

So, step by step instructions:

1. First of all, the side and longitudinal drawers are fixed on the outside of the legs flush with the ends. After that, with the help of self-tapping screws 4 × 50 mm, corners are attached from the outside and from the inside 4 × 16 mm. The corners are attached to the longitudinal tsargs through horizontal slats.
2. Further, a wide guide is fixed on the inside of the side tsarga.
3. Under the dowels, you will need to drill two holes on the inner ends of the tabletop. They are attached for a collapsible connection, that is, one half will be free, and the second will be attached to the glue. From the dowel to the edge of the countertop, the distance should be equal, but not exceed 10 cm.
4. Two dowels are mounted on a removable tabletop. To do this, two holes are drilled on the reverse side.
5. At the next stage, it's time to assemble the U-shaped parts of the box from chipboard. In this case, the end elements 600 × 120 should be located between the sidewalls 420 × 120 mm.
6. Now screw on the narrow guides. This is necessary so that the chipboard box moves on average 2 mm higher than the plywood collet.
7. After that, the guides snap into place and are checked for movement along the drawer.
8. Attach the non-removable part of the tabletop using corners and 4x16mm self-tapping screws. Both parts must match perfectly. Therefore, just before attaching them, slide both parts and check their alignment. Then carefully push the drawers apart and secure the countertops.
9. On the shelf inside the table, place the removable part of the table top.

Folding table - an original solution for a small kitchen!

If your kitchen has a miniature size, then choosing the right shape for the kitchen table can be difficult. However, there is always a way out. For example, you can build a homemade folding table. When folded, it will serve as a decorative frame, and when unfolded, it will serve as a full-fledged dining table. Although in each case the size of such a table will be different, we will take our sizes as a basis. This will allow you to visualize what exactly your drawing will look like.

For work you need:

• MDF board 180 mm thick - 5 pieces,
• 150×90 cm,
• 130 × 10 cm - 2 pieces,
• 90×20 cm,
• 70×20 cm,
• holdfast,
• wood glue,
• acrylic putty,
• electric drill,
• drill for wood 3 mm and for metal 8-10 mm,
• sandpaper,
• acrylic paint for wood
• roller,
• masking tape,
• screws 3.5×30 and 3.5×16 mm,
• loops,
• screwdriver,
• two furniture bolts.

The whole process of work will not take you much time if you strictly follow the step-by-step instructions below.

1. Based on the set of material, the table will be made of MDF. Make drawings first.
2. The frame is built first. To do this, four smaller elements are attached to the largest board from below, using a carpentry vise. Every 250 mm, holes are drilled in the frame with a Ø3 mm drill, up to 3 cm deep.
3. After that, a hole is drilled with a metal drill Ø8-10 mm to a depth of 3 mm. In this way, it will be possible to deepen the heads of the twisted screws.
4. Further, carpentry glue is applied to the lower surface of the four frame elements, and after that, each element is applied in its place. Each of them must be well pressed with a carpenter's vice.
5. Mounting the frame on glue is not enough, so you should additionally fix it on screws.
6. At the same time, disguise the screw heads so that they do not spoil the overall look. To do this, you will need acrylic putty.
7. When the putty has dried, you can sand the surface of the decorative frame with sandpaper.
8. The ends of the countertops should be glued with masking tape.
9. Paint the surface of the frame with acrylic paint using a roller, and paint over the corners and edges with a brush.
10. Then screw the hinges along the short edge of the tabletop. From the edge must be at least 150 mm. Mark holes on the wall and drill for the dowel. Thus, the hinges will be screwed to the wall.
11. When the table is in an upright position, it will be held on top with latches. They should be fixed in such a way that they are not conspicuous, for example, at the edges of wall shelves.

Table from postforming table top in 5 steps

Such a table can be completed in the shortest possible time. To do this, you will need to first collect all the necessary material and tools. You will need:

• pencil,
• postforming tabletop,
• jigsaw,
• jigsaw file,
• Sander,
• edging,
• cutter,
• silicone sealant,
• rubber mallet,
• sharp knife,
• clamps,
• metal legs with holder
• hex key.

All work can be done in 5 successive stages.

Stage 1

Mark the front side of the table top with a pencil. The markup will match your drawing. Each rounding is performed with a radius of at least 60 mm. This will prevent the edge from discoloring at sharp bends.

Stage 2

Now you need to give the appropriate shape to the countertop. To do this, use a jigsaw. When cutting, it is recommended to leave a small backlog of 2-3 mm. Pay attention to the direction of the jigsaw blade. It must have a reverse direction of the teeth. This will avoid chips on the plastic coating. Although partially they can be hidden by piping. In order to accurately bring the dimensions and shape of the tabletop, it is necessary to work on the ends with a belt-type grinder.

Stage 3

In the third step, it's time to mill the groove. Milling is always performed strictly in the center of the end face. And this is even regardless of whether the edging will exactly match the thickness of the table top or will be large. If you do not have a cutter with the exact dimensions of the edge groove, then you can go several times with a cutter that has a lower tooth height.

Stage 4

When the groove is ready, you can start stuffing the edging. To do this, the end face is pre-coated with silicone sealant. This will prevent water intrusion. Sealant is applied to the top edge of the edge. The edge itself is stuffed with a rubber mallet. The joint should be formed in the most inconspicuous place. When the stuffing is completed, it is important to make an exact docking of the piping. There is no way to do without a sharp knife. After that, you will need to remove excess sealant around the entire perimeter of the countertop, which was formed when the edge was driven in.

When fixing countertops using clamps, it is important to use special gaskets. They are installed on the protruding edges of the edge and prevent their damage.

Stage 5

At the final stage, the legs are fixed. To do this, you should attach the molded holders to the underside of the tabletop. So that they are at the same distance, mark up with a pencil. From the edge of the leg should be at a distance of up to 10 cm. This holder is fixed with self-tapping screws 2.5 cm long with a countersunk head. Now it remains to make the final touch: fix the legs in the holder with a hex wrench. The dining table for the kitchen is ready!

As you can see, the table from the postforming tabletop is very simple and, most importantly, available for home-made manufacturing at home. To do this, you need to have basic carpentry tools. But there are also dangers to be aware of here. If handled carelessly, there is a risk of breaking the holder, which is made of fragile material. But if you carefully operate such a table, it will last for many years.

The choice is yours

We have considered with you several options for how to make a kitchen table. There are other technologies for its manufacture. In most cases, everything will depend only on your financial capabilities and ingenuity.

Video

This video shows an example of making a rectangular kitchen table with rounded corners. Balusters are skillfully used as legs: