Chasing cast iron sewer pipes. Do-it-yourself technology for caulking cast-iron pipes

Reading 6 min.

If you plan to install cast iron sewer pipes, you need to take into account the configuration of the room in which the installation will be carried out. This is necessary in the case when it is necessary to make repairs with the rearrangement of plumbing fixtures, for example, a shower cabin is installed instead of a bathtub or vice versa. It may be necessary to add elbows, increase the length of the pipeline. You need to start by preparing the room. Determine the most appropriate type of connection and method of installing communications. Installation of cast iron pipes is carried out after the fittings are selected.

Pipes for installation

Preparatory work

Products are checked for defects. External characteristics are evaluated: the pipes should not have dents, cracks, bumps and spots. It is recommended to use communications characterized by a flat surface of the walls. You can lightly tap on the products. In different places, the sound should be the same. The condition of the cut is also evaluated. Its structure should be homogeneous, fine-grained.

If you plan to change cast iron pipes, you must first dismantle the old communications. For this purpose, a hammer is prepared (for horizontally oriented products), a grinder. The sawing of the riser is carried out only with the help of a grinder. It is not recommended to use a hammer in this case, since individual parts can get into the pipe lumen, which will lead to hard-to-remove blockages. Before installing communications, it is necessary to block the water riser. In the case when the connection of the toilet bowl is changed, the drain should not be used for some time.

Varieties of installation

The pipeline can be located vertically or horizontally. The choice of the method of installing communications is determined by the intended purpose of the connected plumbing fixture and the tasks that need to be solved through these pipes. In order to increase the reliability of fixing the structure, special fasteners are used. In each case they are different.

Vertical

The height of the premises is significant - from 2.5 m. To prevent the pipe from "walking" in the opening of the ceiling, steel clamps are used. They are recommended to be installed under the butt joint (under the socket). The clamp securely holds the pipeline, because it completely covers it in diameter. Fasteners are fixed on the wall. They are installed with some step.

Horizontal

The principle of pipe support in this case is similar to that previously considered. In this case, the fasteners are arranged with equal spacing. Clamps in this case do not provide the desired result, it is recommended to use hanging hooks, brackets, consoles. All fastening elements must be made of metal, steel products are more often used. They are durable and last for a long time.

Connection types

There are several ways to connect. Thanks to a wide range of options, it becomes possible to choose the most suitable method, taking into account the operating conditions of the pipeline. Overview of connection types:

1. Trumpet. Communications in this case have an extension on one side. It looks like a cuff. A rubber gasket is installed in the socket. Then a pipe is inserted into this expansion. The result is a reliable, durable connection. However, its quality is determined by the characteristics of the gasket. If the rubber deforms or loses its properties, which often happens during prolonged use, then a leak will form. You can fix it by replacing the gasket.
2. sealing method. In this case, communications with a socket are used, however, the gasket is not installed at the joint area. The cracks are filled with tow, after which they are cemented.
3. Socketless connection. In this case, an adapter in the form of a coupling is used. Communications are installed in this product from two sides. Then, in this section, the pipeline elements are coupled with metal clamps.
4. Plastic joint. Docking according to this principle is performed when it is necessary to connect sections of cast iron and plastic pipelines. To do this, use special adapters, sealant.

What should not be done during installation?

• use of a gas burner during dismantling;
• the use of a welding machine to connect sections of the pipeline;
• cleaning the surface of communications.

Security measures

When installing a cast-iron pipeline, care must be taken when handling such products. Cast iron is distinguished by reliability and durability during operation, but it is a fragile material, which manifests itself during transportation and installation. During cutting, small pieces of metal may break off. When they enter the pipeline, they contribute to a decrease in the clearance. In addition, fragments can get into the face, injure the organs of vision. For this reason, it is recommended to wear a protective screen or goggles while working with cast iron communications.

If pipe cutting is performed in a room with installed plumbing fixtures and furniture, it is necessary to maintain their integrity. To do this, before starting dismantling, cover all objects with a dense cloth.

Cast iron fittings

The elements are made from wrought iron. Fittings made of this metal can only be used to connect cast iron communications. They are not suitable for steel products. There are several types:

• threaded;
• compression;
• press fittings.

To increase reliability, such products are coated with zinc. According to the connection method, threaded elements are divided into 3 groups:

• with internal thread;
• external thread;
• external-internal thread.

When assembling the pipeline, different shaped elements are used, which are different in shape and configuration:

• revision - used to eliminate blockage, with the help of such an element, preventive cleaning of the system is performed;
• coupling - allows you to join pipes of the same diameter;
• cross - used to change the direction of the pipeline, create several directions;
• transitions - used when connecting communications of different diameters;
• tee - allows you to combine pipelines in three directions or perform wiring;
• indent - used in cases where it is necessary to slightly change the direction of the pipeline;
• knee - an element with two outlets located at an angle of 90 °;
• branch - resembles a knee, however, the angle of rotation of the outlets relative to each other is much smaller (45 ° or less).

Methods for caulking sewer pipes

In this case, a cement mixture, tow is used. With these materials it is possible to caulk gaps in the flare connection when a rubber gasket is not used. This method is considered the most reliable, due to the use of cement mortar. The chasing technology is implemented in stages:

• first, two pipes are connected, and the size of the gap should not be less than 3 mm, otherwise this method will be difficult to implement;
• the tow is hammered into the leak between the pipes using a narrow spatula, screwdriver, chasing, the depth of filling the slot is 2/3 of the length of the socket;
• the remaining part of the cast-iron expansion of the pipe is sealed with cement mortar.

For greater reliability, cement grades M300, M400 should be used. The better the characteristics of the material, the lower the risk of future leakage.

Use of cement mortar

In order for the connection of cast-iron pipes to serve for a long time, you need to properly prepare the mixture. The recommended ratio of cement and water is 9:1. The remaining free part of the socket is filled with the mixture. Given that the solution is quite thick, a chasing and a hammer should be used to seal when filling the metal cuff. These actions continue until the tool bounces off the solution. To improve the properties of the cement, the suture is closed with a damp cloth.

It is important to firmly fix the pipeline during the work, until the solution completely hardens. You can not use it for the next 2-3 days, because this may affect the quality of the connection. Cracks appear in the cement layer if the pipeline is deformed during the drying process.

The use of asbestos cement

The addition of asbestos to the solution contributes to additional hardening. In its pure form, this material is not reliable enough. The recommended ratio of cement and asbestos is 2:1. The principle of connecting pipes using this solution is no different from the previously considered case when pure cement is used. For the preparation of asbestos cement, the same amount of water is taken. The result should be a thick mixture.

Almost all Soviet buildings are equipped with cast-iron sewer communications, since such pipes are durable and resistant to wear. But the cast iron pipeline requires the right approach to use and dismantling.

Unlike drain pipes, which can last for decades, connections inside a home may need to be replaced sooner. Also, interventions in the sewer system may be forced during the installation of washing equipment or redevelopment of the bathroom. To do it according to the rules, it is not necessary to call and wait for the master, all the work can be mastered by the owner himself, if he knows how to handle elementary tools. Dismantling the sewer should not take much time, but dismantling old products is more difficult. Let's figure out how to properly dismantle cast iron pipes.

Step-by-step caulking of cast-iron pipes

In the process of repairing sewer communications with your own hands, the most difficult moment may be caulking a cast-iron pipe. Such manipulation may be required when repairing or reinstalling the riser. In this case, it is necessary to very carefully emboss the pipes of the cast-iron pipes. Step by step, this work can be done like this:

1. First, use a hammer to lightly tap the socket, while being careful not to break it, since carelessness can lead to irreversible consequences, for example, replacing the entire riser. It is better to use a wooden mallet.
2. If the previous blockage was made with the help of a cable, then after tapping the socket should wobble freely and can be removed without additional effort. In such a case, do the following:
   • swing the bell from side to side;
   • pry with a screwdriver and pull the rope a little;
   • hook it with pliers;
   • slowly and carefully pull out the rope, swinging the pipe in the process.
3. If, after tapping, the pipe did not start moving, it means that the previous caulking of the sockets of sewer pipes was carried out by pouring sulfur. In this option, you will need to get rid of it by burning it. To do this, proceed as follows:
   • gently heat the pipe at the joint along the entire diameter with a blowtorch or burner;
   • lightly, trying not to break the walls of the pipe, then tap it with a hammer;
   • if the bell starts to wobble, try moving it using an adjustable wrench.

   Please note that when working with a burner and sulfur, it is imperative to protect the respiratory tract with a mask so as not to get poisoned by toxic fumes.

4. After successful dismantling, the walls of the socket must be well cleaned with a chisel and chisel. Pay special attention to the bell seat, as this is where you will place the sealing rubber.
5. Having previously coated the rubber seal with a special lubricant, place it in the socket.
6. Place a new structural element in the rubber ring.

Precautions in repairing cast iron pipes

When working with such pipes, be sure to remember that cast iron is a relatively brittle material with its endurance. If you hit the metal hammer hard or too hard, the wall will vibrate, which may cause cracks. If this happens, the replacement of damaged sections will be long and expensive. Therefore, when preparing for dismantling, stock up on the necessary tools in advance.

Don't work alone, it is unsafe and difficult. Better call someone for help.

It's important to know that sulfur fumes can be harmful to health, so use a gas mask, in extreme cases, a respirator and goggles. Also take care of good air circulation in the room where the repair work is taking place.

After removing the pipe from the socket, take the time and attention to clean the seat of this part. So you will ensure the installation of the sealing material without defects and distortions.

Immediately pack all dismantled material and garbage into construction bags, tie and throw away. An unpleasant smell will come from the old pipeline.

If you are caulking cast iron pipes for the first time and after reading this article, you still do not understand how to do it, be sure to contact a professional. For an experienced craftsman, the process of dismantling cast iron pipes will take 25-30 minutes, while a beginner can spend more than 3 hours and with an unknown result.

Before the advent of new materials, such as metal-plastic or plastic pipes, most houses had steel or cast-iron sewers. Before installing a new pipeline, it is necessary to dismantle the old one, which is not an easy task, because earlier cast-iron structures were connected with cement mortar, aluminum or sulfur. Such a pipeline is difficult to dismantle, so it is worth preparing for a laborious and protracted process.

When a cast-iron sewer is being dismantled, a wide variety of tools can be used, because it all depends on the method and material of chasing. However, the most important devices can be distinguished - these are:

• grinder, with which you can cut out a pipeline element;
• grinding or cutting discs;
• blowtorch;
• a set of different screwdrivers, a hammer;
• chisel;
• special pipe wrench;
• goggles, a mask, and when disassembling structures that were connected with gray, also a headdress;
• perforator;
• nail puller or crowbar;
• pipe cutter;
• chisel or steel wedge;
• iron bucket with water.

Before starting work, it is worth determining the connection method in order to sketch out a rough plan for how to disassemble the cast-iron sewer.

Moments of dismantling cast iron

With a complete replacement of the structure with a plastic one, you can not do extra work and just smash everything with a hammer. This is quite easy to do, because cast iron is considered a brittle material. However, if only part of the pipeline needs to be dismantled, the work must be done more carefully.

Before dismantling the cast-iron sewer, it is necessary to inspect the entire system to determine the area that will be repaired. Then be sure to turn off the water supply so that the drains do not enter the sewer. Further disassembly is carried out in stages:

1. The part of the pipe located below the connection is cut off.
2. The pipe is separated from the socket. The embossing methods will be discussed in more detail.
3. If you remove the connection just does not come out, use a blowtorch or make surrounding cuts 20 mm long.

When carrying out procedures, it is imperative to use all protective equipment due to the injury risk of this work.

Caulking of the pipeline with sulfur compound

Regardless of how the cast-iron sewer was connected, it is imperative to carry out some standard preparatory work before replacing:

• turn off the water;
• disconnect the hose leading to the toilet;
• remove the toilet itself by unscrewing the bolts;
• clean the bathroom of appliances and furniture.

To determine whether sulfur was really used when connecting pipes, you need to bring a blowtorch to the seam. Under the influence of high temperatures, sulfur melts, accompanying this process with an unpleasant odor.

When disassembling cast-iron sewer pipes, work begins from the farthest corner. The element must be broken with a hammer. It is better to use a tool with a plastic or polymer base, because the sewer can become clogged due to metal nozzles. Having found the cross leading to the riser, it is necessary to loosen it as much as possible.

Then you need to prepare a blowtorch or gas burner. At least two people should be involved in heating up the connections. While one warms up and melts sulfur, the other must loosen the structure. When doing this, be sure to use gloves and other protective equipment.

When the connecting substance is completely melted, the crosspiece can be removed from the riser. At the same time, you should be very careful, you need to remember to remove the remaining sulfur, and then let the riser cool thoroughly. If the cast iron structure is too strong, you can always make a few cuts near the pipe that needs to be removed. This will make the extraction process easier.

Cement bonded pipeline caulking

Dismantling cast iron pipes that have been connected with cement is practically the same as the above-mentioned sulfur option, but it is much safer. This is because when sulfur melts, a lot of carbon monoxide is released.

To start dismantling, you need to cut off part of the pipe. In this case, it is worth retreating at least 30 cm from the junction. The hardened cement is removed with a hammer, which must be beaten with a screwdriver or a chisel inserted into the hole. All procedures should be performed as carefully as possible so as not to damage the socket.

When the joints are freed from cement, you need to try to loosen the main pipe. In order not to process the sewer with a blowtorch or a burner, it is necessary to remove the cable, but if this cannot be dispensed with, it is necessary to heat it up strongly or use a specialized key. For example, for a 50 mm pipe, tool Nos. 3 and 4 are used.

The crosspiece is located below on the main riser. To remove it, you can simply use a hammer with a screwdriver. At the same time, for some time, you need to lightly tap on the tee itself in order to form a small gap between it and the pipe. Then you need to penetrate this opening, pry off the tee and remove it. It will take a lot of time to carry out these manipulations, in addition, this method is ineffective.

The next option is to use a blowtorch or burner. Dismantling is much faster, but the price for this is an unpleasant smell that takes a long time to disappear. First of all, you need to cut the socket of the cross. Then a heating device is placed in the pipe. A metal shield is applied to the upper part of the pipe in order to be able to regulate the draft inside the riser. When heated, you need to start swinging the pipe and, as soon as possible, remove the dismantled tee.

You can also use a grinder. To do this, you must first cut off parts of the tee, leaving a small piece in the pipe. Then put a medium-sized disk that could freely get inside, and cut through the remaining parts of the structure with a grinder, knocking them out with a hammer.

What to do in case of failure?

The dismantling of the pipeline is carried out to the permissible limit, because it is better to cut the pipe before it passes into the socket. At the same time, joining a cast-iron pipeline with a plastic one will take much less effort and time. It is better to cut the structure with a grinder, but if it is not there, you can use a hacksaw to work with metal. The use of this tool can greatly increase the duration of the dismantling process.

If the dismantling was unsuccessful, do not be upset, because you can simply purchase a specialized transitional coupling, with which cast-iron and polymer pipes are connected.

If you have difficulty cutting the pipe, you can cut it in half. Then you need to apply slight pressure or rotate so that the element bursts. If it cannot be removed from the socket, you just need to make several cuts in a circle with an interval of 20 mm, after which it can be removed from the riser.

Before starting the connection of the cast-iron and polymer pipeline, it is necessary to clean the first option of sulfur by heating. After removing the substance, it is necessary to leave the pipes for several hours and allow them to cool.

A modern sewer system is a complex structure that at times increases the comfort of life for the inhabitants of a country house or an apartment in a multi-storey building. In order for the sewerage system to function properly, during the installation process it is necessary to ensure that everything is done correctly, otherwise you may encounter trouble during operation.

Over time, sewer pipes fail and need to be replaced. Considering that in most Soviet-era buildings, mainly cast-iron pipes were used to install the sewer system, now it is necessary to carry out either a complete replacement or a partial one.

Chasing and chasing sewer pipes

Note! Cast iron pipes under the influence of aggressive factors from the outside can lose their functionality and fail in exactly the same way as plastic products and steel pipes.

An important place in the process of repairing sewer pipes made of cast iron is their caulking and caulking - procedures that are carried out using special technologies and building materials.

The one who assumes that it is easier to dismantle a sewer pipe than to install is mistaken. The first stage on the way to replacing an unusable element is the chasing of sewer pipes, or rather chasing. It takes a lot of hard work and dedication to do this job. This job is quite dirty and unpleasant.

Chasing a sewer pipe is required if the socket method was used during installation work.

Note! Chasing is performed in different ways, depending on which method was used to give strength and reliability to the connection.

To figure out how to caulk a sewer pipe, it is necessary to determine whether a sealant or sealant is used to connect cast iron pipes to each other.

• Chasing the pipe on the seal begins with the fact that it is tedious to beat off the waterproofing layer with a special rubberized hammer. After that, the joint is loosened, the camboca is removed, the sewer pipe is removed from the socket.
• The caulking of the pipe on the sealant is performed a little differently. First you need to tap the joint, then remove the waterproofing layer, burn the sealant with a blowtorch. Once the pipe has cooled, it can be easily removed from the socket.

Note! After the caulking has been done and the damaged part of the cast iron sewer pipe has been removed, it is not recommended to install a replacement from that material. It is better to replace the cast iron pipe with a plastic counterpart. Plastic is in no way inferior to cast iron, but is a lighter and cheaper material, and besides, it does not corrode.

Methods for caulking sewer pipes

When installing a sewer system using cast-iron pipes, which are connected in a “bell” way, voids are formed at the joints, which can adversely affect the functioning of the sewer. In order for the connection to be reliable and durable, caulking of sewer pipes is required. It can be made using different materials. Most often it is cement and asbestos cement.

Use of cement mortar

First you need to mount the resin seal in its place. The tarred rope must be tamped into the hole of the sewer pipe and the socket. After the formation of the first ring of the tourniquet, we overlap its end from above so that it cannot penetrate the pipe in any way.

Methods for caulking sewer pipes

Now you need to prepare the cement mortar. To do this, cement is poured with water, in a ratio of 9: 1. As soon as the solution cools down a bit, they need to fill in the junction. Using a hammer, we drive the cement into the joint. For a better fight between the solution and the tarred rope, it is necessary to cover the cemented joint with a damp cloth afterward.

Note! If you use extended caulking and embossing in the course of work, the installation speed will increase by 30%. If caulking is performed during the cold season, the cement mortar is prepared not in cold, but in hot water. After completing the work, it is necessary to take care of the insulation of the joints.

The use of asbestos cement

The asbestos-cement mixture is also suitable for performing work on the sewer cast-iron pipe. In this case, the workflow will be slightly different.

Chasing pipes

• First you need to make a solution. To do this, in a container, mix a mixture of dry asbestos fiber with cement. For one part of the mixture you need to take two parts of cement.
• Now the resulting mixture needs to be slightly diluted with water so that it adds 10-12% of the mass, stir until smooth.

There is no fundamental difference in how the sockets of sewer pipes are caulked with an asbestos-cement mixture or cement mortar.

Note! Cast iron is a rather fragile material despite all its technical characteristics. During operation, it is exposed to water, solid waste, aggressive chemicals. In order to extend the life and improve the quality of service of sewer pipes made of this material, it is necessary to caulk the connections.

Before you start doing the work with your own hands, you need to familiarize yourself with all the nuances of chasing. The procedure is quite complicated and time consuming. Without even the slightest experience in carrying out construction work, you should not even take on the execution of caulking.

Do-it-yourself installation of sewer pipes requires the contractor to fully comply with the rules of construction work and standards. In most cases, these issues have already been resolved for multi-apartment buildings, so this process is relevant for private houses and cottages. It is for this reason that owners need to know all the nuances of building a drainage system. In our article we will find out how to make a sewer with our own hands.

It is necessary to install water pipes from the drawing up of communication laying diagrams. The photo should indicate and indicate all the components of the structure: the dimensions of the elements, the location of the fittings, the lines of the system. In practice, most plumbing fixtures are connected to one riser, but if the room is large, it is better to connect to several points.

When the question arises of installing a sewer system, you can start from the photo of the previous wiring diagram in the building. It is worth considering that if a cast-iron pipe is replaced with a plastic one, then it is impossible to focus on the old system.

Attention! With a large number of storeys of the building, it is rational to place the plumbing units one under the other.

When performing repair work, it is enough to make a schematic drawing of the adjustable system. But, if sewage installation is being carried out, then it is impossible to do without drawing up a project. This norm is necessary due to the existence of an internal and external design of the drainage system. Plus, most cases also involve the installation of a cleaning device.

Work materials

For such types of work, the requirements of SNiP provide for the installation of the following types of pipes:

• cast iron;
• ceramic;
• Asbestos-cement;
• ceramic;
• Plastic.

Most often, polyethylene materials are used, which correspond to GOST 22689.0-89 and 22689.2-89, and have a diameter of 40 to 110 mm. A feature of plastic pipes is resistance to aggressive environmental influences and corrosion. Such devices are connected using sockets, and rubber cuffs are used for sealing.

Basic rules of the installation process

Before proceeding with the installation work on the sewer, you should familiarize yourself with the basic requirements for the process. This is necessary to create an optimal drainage system in the house. For this reason, it is very important to do everything correctly and accurately.

Sizes of diameters and slopes of pipes

Since most situations involve the creation of a system with gravity, it becomes very important to choose the diameter and slope of the pipes correctly. The functioning of the sewer will depend on this process. The size of the pipe dimensions is affected by the type of plumbing fixtures, as well as their number in the building. Generally speaking, the main factor is the photo installation diagram. So here are some recommendations:

• It is better to insert a pipe diameter into the washbasin system - 4 cm;
• For bathroom and kitchen - 5 cm;
• For a riser that does not have a connection to the toilet - 8.5 cm;
• For a riser with a connected toilet - 10 cm

Attention! The pipe must be directed to the riser from the apparatus. It is worth noting that its dimensions should be 2-15 cm per meter.

Dismantling the old wiring

Before mounting a new system, you need to remove the elements of the old layout. It is worth noting that this process can be quite a difficult job, especially for old-timers' houses. In order to speed up and facilitate the procedure, it is necessary to think about dismantling in advance.

Required Tools

To install the sewer with your own hands, you will need the following tools:

• Special grinder or hacksaw;
• Drill apparatus;
• Screwdriver.

It is right to start all work from the bathroom and the most distant places of pipelines. Before starting the process, it is necessary to check whether all the necessary materials and tools are available. In addition, we advise you to perform pipe diagnostics to determine if there are any deformations and damages on them.

Preparatory stages of installation

Preparation for installation includes the following steps:

• We check and adjust all connection points. We mark on the pipes the depths of the occurrences of the sockets.
• Next, the chasing and cutting of pipes is performed;

Attention! The caulking of the pipeline occurs at an angle of 90 degrees. It should be noted that the cut should not have deformations or distortions.

• The points of cut pipes should be correctly checked for burrs, as their presence on the part will affect the sealing of the joints and lead to the accumulation of debris and blockages. You need to fix this situation with a file.
• Before assembling the system, it is necessary to clean the extreme parts of the pipes and the rubber seals. Failure to comply with this norm will reduce the quality of the connection.

If you focus on the standard photo, the sewerage scheme in the premises, then it provides that the pipe wiring is carried out along three lines of the system:

• The device of the first highway is the line with the shortest length, which should not exceed 1 meter. In this branch, it is necessary to mint a toilet bowl and other plumbing fixtures in the house.
• The second line includes bathroom appliances and equipment, namely a washbasin, shower, washing machine.
• The third branch is the drainage line from the kitchen.

Attention! The length of the second and third branches should be less than three meters. For this reason, if the building has a large volume, then it is necessary to insert the lines into at least two risers.

The main sewer lines have several branches that go to each type of plumbing. Each line at the end provides for the installation of a siphon. A water lock is a necessary element of any system that forms a cork from the water, which prevents gases from escaping from the sewer. In most cases, such an apparatus does not exist in the installation of a washing machine, since its system has a check valve.

Chasing cast iron pipes

Sometimes there are situations when there is a need to perform repairs for a separate part of the sewer system. It should be noted that the process does not always occur without disconnection of the pipeline. To start minting pipes, you need to inspect the place of future work.

The main problem is that the pipes that are in the ground are filled with a special substance, which strengthens the fastening. Therefore, the question arises, how is the chasing of cast-iron pipelines performed? This is what we are now trying to find out. It is enough to simply destroy the connection using a gas cutter.

Pipe chasing technology

Difficulty can also arise when chasing cast-iron or plastic pipes, which occurs when replacing a riser or toilet bowl. For the correctness of the action, you need to very carefully mint the pipe pipe. This action includes several steps:

• The first thing we need to do is to tap the bell with a hammer so as not to damage it;
• If the bell moves quietly and can be easily dismantled, which means that the caulking was carried out with a cable.
• Then you can start dismantling - loosen the bell, pry with a screwdriver and pull the cord a little. Then gently pull out the rope with pliers.

If the bell is motionless when tapped, this means that the chasing was done with sulfur. In this situation, you need to use the burning technology:

• Carefully perform heating of the pipeline around the circumference with a burner or blowtorch;
• Avoiding damage, carefully tap the pipeline with a hammer;
• When the bell is movable, you can loosen it with an adjustable tool.

Attention! When performing work, it is necessary to use a respirator to avoid inhalation of sulfur.

• After releasing the bell, we clean it with a chisel;
• We cover the sealing ring with a special solution, and insert it into the socket;
• We mount a new part in the seal.

Installation of plastic sewer pipes

Installing plastic sewer pipes is a little different from other types. For this reason, we provide some tips on how to mint them:

• There are two ways to cut a plastic pipe. It is worth noting that the saw for such work should have small teeth. Also, this task can be performed using a two-handed cable.
• Do not leave burrs, which very often appear when cutting plastic products.
• We carry out cleaning and gluing of materials. First, you need to perform a dry assembly, and then you can start gluing the system. To do this, we make marks, and then we connect the structural elements with glue.
• We assemble the sewerage pipeline system.
• We fill in all the empty spaces.
• We install a plastic pipe for ventilation. The connection must be made with copper material.
• Plastic pipes are used for connections of high complexity. The strength of the tightness of the structure is provided by couplings without a socket.
• We strengthen the risers. To do this, use metal lining - this element will protect against accidental hits of small parts, such as nails or screws.

So, we found out that installing a sewer is quite simple. The article presents two options for completing the process - a design with cast iron and plastic pipes. The main requirement for installation is compliance with the rules and regulations that are regulated by SNiP and Gost RF. So, study the legislative base and construction and sanitary conditions, and then you will be able to install a drainage system in your own house or apartment correctly.