Warm skirting board with your own hands. Baseboard heating - is it worth doing or not? Do-it-yourself skirting water heating radiators

Faced with the choice, from a sufficiently large number of options, of the most efficient way to heat a home, people most often resort to those options that provide the minimum initial investment that can provide an acceptable heat transfer coefficient. A new trend in this matter was the installation of a heated baseboard. In Europe, this system has been used for about two decades, which, accordingly, indicates a fairly high efficiency indicator. The electric plinth is a metal structure, inside which a heating device is installed, heating occurs directly with the help of infrared radiation. This system can work in a single version or in tandem with radiator batteries.

Installation is possible in almost any territory, whether it is an apartment or a summer cottage. If you decide to join the owners of these units, we will tell you how to install a warm water and electric baseboard with your own hands.

Outwardly, all elements of the unit do not have any special differences in comparison with an ordinary plinth, most often made of an aluminum collapsible casing. The dimensions of typical models of a warm baseboard are 14 centimeters in height and three in width. Inside, by means of mounted brackets, a heating element is installed, which consists of two copper pipes interconnected by brass ribs. All heating units are connected into a single system using crimp nuts or by soldering with copper solder. At the corner sections, the elements are connected using copper or polymer tubes. You do not have to worry about the fact that over time the device will rust, because in the production process of the product only non-ferrous metals are used, which in turn provide a high heat transfer coefficient of the baseboard.

The principle of operation of a warm plinth

Installation of a warm skirting board is carried out around the entire perimeter of the room, so the room is heated smoothly and evenly. This is ensured by means of heat distribution through special holes located in the upper part of the device. In order to heat the room to an acceptable level, 20-24°C, it is necessary to heat the aluminum plates to a temperature of 40-70°C.

It is worth paying attention to the following aspect! Compared to conventional radiators located at a certain distance from the floor, the warm baseboard system produces heat almost from the very bottom of the room.

The heating of the space is carried out due to the heat transfer of the walls, they first absorb the heat coming from the baseboards, and then become passive sources of heat. Due to the fact that the heat is evenly distributed throughout the room, you will not have cold spots anywhere. The installation of furniture will in no way affect the operation of the device, the efficiency will remain at the same level.

According to the principle of operation, the units are divided into electronic and hydraulic.

The electric plinth is made of paired pipes made of copper, where a cable is mounted into one of them, from a heat-resistant material with silicone insulation, while a low-temperature heating element is placed in the other, with a maximum heating temperature of about 60 ° Celsius. The temperature is controlled by an electrical sensor, a thermostat. The product has a special clamp for grounding, do not neglect this.

In a water plinth, distilled liquid or antifreeze acts as a heat-conducting liquid. Heating of these elements occurs with the help of a boiler, or with the help of a tie-in into a centralized heating system. This method is more economical than the electric baseboard, since the second one consumes electricity in a certain amount. The temperature is controlled by means of a thermal valve or in automatic mode.

Pay your attention! The distance to which the water plinth lines can be stretched is limited to 15 meters, if the room is larger, then additional autonomous circuits must be installed.

We list the main advantages of this type of device:

The principle of heating a room by means of a warm baseboard, according to its principle of operation, is remotely similar to a warm floor, but the installation process is less labor-intensive and much more economical. Note that you will not be able to install underfloor heating, especially water, in many rooms. To install the skirting board, you only need a completely flat wall. If necessary, you can easily dismantle and install the system in another place.
With the help of a warm baseboard, you can achieve a favorable climate in almost any room. Slowly rising air currents will not drive dust around the room. Heat is not concentrated in the upper part of the room, but will be evenly distributed throughout the room.
Due to the fact that the walls will act as a heat-receiving screen, you can forever forget about the presence of mold and dampness in the room. Condensation will not form on spacious glass areas.
The installation of such a system will not make an ordinary person sweat, because ease of assembly is ensured by the modularity of the structure, which simply needs to be simply connected to each other and connected to a power supply or a centralized heating system.
Due to the fact that the appliance does not heat up to high temperatures, you can not be afraid that your furniture, wallpaper, curtains or other household items will become unusable.
The plinth will not be noticeable to your guests, it will harmoniously fit into your interior, because before buying you can choose the color to your liking.

Let's go through the cons:

One of the first disadvantages is the amount required to purchase a warm baseboard system.
The second drawback that is present in electric baseboards is the price of electricity, because they are growing day by day, and you need a considerable amount of it for normal functioning.
The system of warm plinth is not able to heat the room in an instant, it is designed to maintain the temperature in the room.

Preparatory measures before installing the system

The first step is to calculate the required power of the device, as well as make a choice of the type of device, water or electric. The number of required heating elements for each room will be individual, and will depend on the climate, the presence of double or triple glazing in window openings, as well as the area to be heated. To ensure an acceptable room temperature, the average value is one hundred watts per square meter. An additional advantage, in terms of savings, is the presence of insulation in your house or apartment, which will save a lot, because in this case it is possible to purchase a cheaper system, or reduce the number of heating modules. To connect the elements to each other, it is recommended to use copper solder, because it is able to withstand high loads, as well as provide reliable sealing of the system. If it is impossible to implement this method, it is necessary to use threaded fittings. Water supply to the system from the boiler must be carried out exclusively with polymer pipes, preferably polyethylene.

Before we tell you about the features of installing an electric or water plinth, first we will consider the general points:

Before you start the installation process, it is necessary to mark the installation lines of the panels, the system must be located at a distance of one centimeter above the floor level.
The panel is attached to the wall using self-tapping screws with plastic dowels. On the back of the panel there are stops designed to provide the required clearance (15mm) between the wall surface and the system.
For better thermal insulation between the casing of the heating element and the wall surface, a heat-insulating tape is glued.
Drill holes for fastening brackets for convectors. To do this, it is best to use dowels with a pitch of forty centimeters.

Electric plinth

Attention! The device has high power consumption, which limits the number of panels used in one circuit to 17 pieces.

Cable wiring must be carried out inside the wall, or installation outside is possible, provided that the wire is insulated with a special box.
The connection of the device to the network must be carried out exclusively through temperature control devices. It is attached to the wall.
Before launching, it is necessary to calibrate the device.

Water plinth

When passing corners, it is necessary to use specially shaped connecting tubes.
Connect the assembled system to the collector and start up hot water.
After making sure that there are no leaks, install the front panel of the plinth.

In this article, we tried to explain the main points on how to install a warm water and electric skirting board, studied the main points of these manipulations and instilled detailed instructions for installation and do-it-yourself.

The most famous modern methods of insulation are the "warm floor" system and radiators. But there is another rather unusual, but already gaining popularity solution - a warm water plinth. It is efficient, compact and combines the advantages of radiators and floor heating. Using this method, you can heat both office space and living rooms.

What is a warm plinth system and how it works

Heating skirting boards are special heaters of compact dimensions, located along the floor along the perimeter of the room. Their thickness usually varies within 3 cm, which is similar to conventional skirting boards. The height of these devices is usually 12-15 cm.

Water heaters can be used both independently and combined with traditional heating methods.

To install a water plinth, you need a boiler that will heat the liquid and direct it into the pipes. But with electricity, everything is somewhat simpler. It is already in the house and no additional installations are required.

An electric warm baseboard warms up a room faster than a water one. And to install it, it is enough to lay and fix the network cable, which is then closed with an external panel. Next, the device is connected to the distribution block and starts its work.

True, it should be borne in mind that with expensive electricity tariffs, such heating will be very expensive. And the use of a water heater is somewhat safer and more convenient than an electric one.

This system also has some disadvantages:

Incompatibility with built-in furniture, as in this case the installation area is closed;

Electricity costs;

Low power, because of which it will not be possible to quickly warm up the room.

When installing a warm baseboard, you should correctly arrange the furniture in the room so that it does not interfere with the movement of warm air currents.

Self-installation of a warm skirting board

The warm plinth system is very easy to install and you can easily mount it yourself, without the involvement of specialists.

Installation of a warm water plinth:

The distance between the section and the collector is measured. Next, the pipe of the required length is cut off with a margin. Ideally, the tube outlet should be 6 cm from the floor and end at least 15 cm before the corner.

Next, skirting boards should be glued around the entire perimeter of the room. Profiles need to be cut and installed on adhesive tape or silicone. You need to start the installation from the corner.

Then the holders are installed. To do this, holes are drilled 15 cm from the end of the profile, and for the remaining clips - a step of 40 cm.

Convectors are fixed. The pipe is joined to the section so that there are no kinks. Copper tubes are completed with nuts, rubber gaskets and a bushing.

Next, the radiator is applied to the wall and the adapter is connected to the section. The cases should fit snugly against each other, but you need to step back from the corners by 1 mm so that there is room for decorative elements.

The remaining sections are assembled in the same way. You need to do this around the perimeter - moving from one corner to another.

The last section should be looped with a stainless steel sleeve.

At the end of the work, plugs and corner joints are placed. The system is connected to the collector and water is supplied.

After supplying the liquid, you need to observe the operation of the heater and check the reliability of the assembly and the absence of leaks.

Electric warm skirting boards are mounted almost exactly the same as water ones. Only instead of a collector, a distribution block is used, where there are circuit breakers for each circuit. Instead of pipes, electrical wires of suitable cross section are laid.

To control the temperature, it is desirable to install thermostats in each room - this will turn off unnecessary circuits and thereby save energy.

Warm plinth (video)

There is nothing complicated in installing a warm skirting board. It is quite possible to do it yourself by installing a reliable, convenient and high-quality system for heating a room.

The history of the emergence and improvement of home heating designs is rooted in the depths of centuries. Today, there are many ways to create a comfortable temperature inside residential premises.

These are central heating radiators, mobile electric heaters, air heaters, underfloor heating and much more. Among all this variety, you should pay attention to such heating devices as a warm baseboard, electric and water warm baseboard. In this article we will try to convey to the reader the concept of what a warm baseboard is.

The principle of operation of warm skirting boards

The essence of the very idea of \u200b\u200bheating with warm baseboards is that the heating system is located around the perimeter of the room near the floor. The heated air in the convector slowly rises along the walls. Due to this, the entire volume of the room warms up.

Such a system of warm plinth, equipped with a thermostat with a temperature sensor, maintains a constant air temperature inside the room, does not form condensation on the glass of window frames, and prevents the appearance of dampness and mold on the walls.

Heat from convectors will not affect furniture

Warm baseboards practically do not take up much space. Despite the high power indicators, furniture and other interior items can be safely placed near the convectors. The surface of the convectors does not heat up to a dangerous temperature level that causes burns.

The trading network offers for sale systems of warm skirting boards of two types. This is an electric skirting board and a warm water skirting board. Consider each heater.

How to make a warm plinth with your own hands, powered by the mains? Having skills in working with electrical engineering, you can assemble an electric warm plinth quite independently.

The heater consists of two horizontal copper tubes. The power cable, covered with silicone insulation, passes through the top tube. A tubular electric heater is threaded into the lower copper tube. The whole system is controlled via an air temperature sensor by a thermoregulation unit.

Heating element - conventional heating element

When the temperature inside the room falls or rises, the heaters periodically turn on and off, thus ensuring a constant temperature regime.

They purchase a set of warm skirting boards based on the calculation of the length of the heaters, rotation angles and other related elements. The heating element itself is a tubular electric heater (TEH), enclosed in a copper sheath.

In turn, a copper pipe is threaded through a body of ribbed thermal reflectors (radiator). Electric heating modules are produced in several standard sizes. Depending on the length of the electric heater, its power changes, as can be seen from the table:

№	Heating element length mm	Power Tue
1	700	140
2	1000	200
3	1500	300
4	2500	500

From heating elements of different lengths, installation of a warm plinth is possible on any area, any configuration.

Installation of electric plinth

Install the heating element 3 cm from the wall

Only a person with extensive experience in electrical work can assemble his floor electric heater by hand. Calculate the dimensions of heating elements, make radiator nozzles, install connecting cables is a very difficult and responsible job. Therefore, it is easier to buy ready-made heating elements for warm skirting boards.

When a heating set of skirting boards has already been purchased, they begin preparatory work.

Knowing that the heated baseboard should not heat the walls, but the air, the fasteners are made such that the heating electrical elements are at a distance of at least 30 mm from the walls. The plinth must be 140 mm high.

Mount the electric heater in several stages:

I install the mounting box at a height of 4 - 6 cm from the floor. Lead the power wires to the junction box.
At a convenient height, a switch with a thermostat is mounted on the wall.
A protective tape 3 mm thick is glued to the walls over the entire height of the plinth.
Markings are applied to the walls for mounting under heated skirting boards.
Drill holes for dowels in places where fasteners should be installed.
Screws are screwed into the dowel through the technological holes in the brackets.
A thermal heating module is hung on the installed brackets.
Connect the modules with electrical wires in parallel.
A residual current device (RCD) is connected to the system.
Connect the air temperature sensor.
Make control inclusion of an electroplinth. If a malfunction is found, fix it immediately.
Install the skirting board.

The lining of the plinth is made of enameled metal panels or plastic. The cladding should not reach the floor surface by 20 - 30 mm. There are horizontal slots on the top of the panels. This design provides a constant movement of air masses from the bottom up. The lining of the plinth, in addition to its function as an air duct, plays a protective role against accidental mechanical influences.

Work related to the supply of electricity to the plinth, connection to the electric meter, installation of a thermoregulation system is best entrusted to a specialist.

Installation of a warm plinth provides complete electrical safety. The places where the wires are connected to the contacts of the modules are closed with heat shrink tubes. The tubes protect the contact surface from moisture. For more information on installing a warm skirting board, see this video:

Despite protection from moisture, experts warn that electric heaters should not be installed in rooms with high humidity.

Most often, such systems are installed in private homes.

Do-it-yourself assembled warm water plinth can create special comfort in residential premises. If you look at the water plinth from a constructive point of view, then we will see compact "stretched" modules in length.

For the installation of a skirting water heating system, private households or public institutions are most suitable. The necessary conditions for the installation of warm skirting boards are the presence of a gas boiler and central water supply.

In some cases, boilers operating on solid and liquid fuels are used. You will also need a reserve tank (water tower) to replenish the water level in the heating system.

Skirting convectors with a water coolant are installed along the perimeter of the room. Modular liquid electric heater can be of various lengths. In the corners of the room, the modules are connected with special corner elements, which fill the fully heated perimeter of the room. Thanks to this placement of skirting boards, the room warms up more evenly than when heating with conventional water radiators.

If you decide to install a hydronic baseboard heating system connected to a central heating system, you will need to obtain permission to install this equipment from the relevant utility companies.

Otherwise, you may be fined and forced to dismantle the heaters.

Hot water pipe connected to gas boiler

The design of the plinth is quite simple. The upper pipe, as a rule, leaves the gas boiler system, passes through the entire perimeter of the heated area and passes into the lower return pipe. The lower pipe returns the cooled coolant to the gas boiler.

The pipelines are built into the housings of the finned heat transfer devices. Due to the ribbed structure, the heat transfer surface increases many times, which significantly contributes to the active circulation of heated air masses.

To install a warm water heating baseboard on your own, you must have sufficient experience in installing plumbing equipment. Telling below about the features of installing a warm water skirting board, we turn to just such people. This will help when choosing a particular heating system for your home.

The principle of heating a room with a liquid converter plinth is no different from heating with other devices.

Cold air enters through the bottom groove of the plinth body.

Passing through the heat exchanger, hot air slowly rises, evenly spreading throughout the entire volume of the room.

According to the laws of physics, the cooled air masses go down, thereby displacing the heated air up. Continuous circulation of the medium evenly heats the entire room.

Installation of skirting water heating system

In construction supermarkets, you can always purchase the ready-made system of water heating for skirting boards that you need. With even a little experience in plumbing work, you can easily make a warm plinth with your own hands. For more information about heating with a warm baseboard, see this video:

After the appropriate marking of the mounting points of the brackets and their installation, the fluid modules themselves are mounted (see above the installation of electrical skirting boards). Unlike electric heaters, the installation of liquid modules requires careful control of the tightness of the pipeline connections.

It is better to entrust the installation of the heating system of skirting boards to specialists.

Testing of installed skirting boards

Air molecules are much smaller than water molecules. Practice shows that checking the tightness of connections is more effective by creating a high pressure of compressed air inside the pipelines.

With the help of a compressor, an air pressure of about 5-6 bar is created in the pipes of the warm floor. All connections are covered with soapy water.

Bubbles will appear where leakage occurs. Leaks in the connections are eliminated and the entire system is re-tested for tightness.

The structure of the water skirting boxes is no different from the lining of electrical modules. The boxes are usually made of thin enameled iron.

Manufacturers, meeting the wishes of consumers, make skirting board cases of various colors. Basically, the assortment is dominated by cases of white color or with a surface imitating precious woods, natural stone or genuine leather.

Often, to design an optimal heating system, it is required to use the smallest heaters in size. At the same time, their efficiency should ensure the normal maintenance of the temperature regime in the room. One of the ways out in this situation can be the use of a warm skirting board.

This design is a small height heating devices that are installed at the bottom of the wall.

Despite its relatively small size, this type of radiator has a number of important advantages:

Compactness. It will harmoniously fit into any room due to the presence of external decorative panels of various configurations and colors.
Uniform heating. Since the structure is installed along the perimeter of the room and the lower part, the convection of air flows occurs simultaneously throughout the entire volume.
Ease of installation. To install a warm baseboard, it is enough to provide a coolant supply (water heating) or a place to connect to the mains (designs with a heating element).

But despite all these advantages, there are a number of significant disadvantages:

If there is a lot of furniture in the room that stands against the walls, there will be little free space for installing a warm baseboard, and the heating efficiency is reduced by an order of magnitude.
Relatively high cost of factory models. The vast majority of them are made of copper, which significantly affects their price.

To solve the last question, you can try to make a warm baseboard yourself.

Design

Structurally, this heating device should consist of several elements.

The back panel, which is necessary for installing heating elements and protecting the wall from thermal exposure.
A heating element - . Their dimensions are usually 1000 * 40 * 160 mm. In this case, the number of heat exchange plates should be maximum.
External panel with slotted holes for air circulation.
Decorative side and swivel caps.

The average power of the factory installation is about 240 W, i.e. for a room with a perimeter of 18 m (20 m²) and an average ceiling height, the maximum power of a warm baseboard will be 4 kW, which is more than enough for efficient heating.

However, for the independent manufacture of such an analogue, it is necessary to make a lot of effort and money, which in the vast majority of cases will exceed the cost of buying a factory copper plinth. The main problems are as follows:

Optimum power rating in copper construction is achieved by a large number of heat exchanger plates. Moreover, their soldering occurs in such a way as to ensure tight contact of the plate with the copper tube. This is the only way to achieve efficient heat transfer.
Production of a decorative casing that would provide normal air heating and at the same time be resistant to thermal shocks.

Is there a way to do this at home? Alas, the efforts to repeat the construction of a warm copper plinth will not be appropriate. Let's consider an alternative.

Alternative

The main task when designing a warm baseboard on your own is to achieve good heating of the room with a minimum height and width of the structure.

Since it is impossible to make copper radiators with your own hands, it is recommended to use copper pipes, but without plates. Their diameter varies from 10 to 20 mm. The most effective size is 16 mm.

They are installed along the entire perimeter of the room at a height of 6 cm from the floor level. For better heat transfer, a strip of reflective foil is attached to the wall surface. A steel box can be used as a protective case. Inside the resulting structure, you can install a heater. As an example, you can see a photo of a home-made warm baseboard.

Effective operation of such a design is possible only if several conditions are met:

Minimum temperature difference between pipes. In this case, the resulting thermal radiation will be more efficiently reflected from the wall surface. To do this, it is desirable to install an individual circular for a warm plinth, which will increase the rate of passage of the coolant, thereby reducing the temperature difference between the heating pipes.
If a copper screen is used as a decorative panel, then it is best to solder the pipes to it. In this case, the efficiency of the system will increase significantly.
When using a heating element as a heating element, it is necessary to provide insulation of the pipe surface from the screen, i.e. contrary to the previous recommendation, the pipe should never be welded to the copper panel.

Width - 3 cm.
Height - 15 cm.
Distance to the floor - from 6 cm.

Otherwise, everything is determined by the parameters of a particular heating system. For the best result, competent calculations of specialists are needed.

How to make a warm skirting board with your own hands? This issue is now very relevant, since the attention of modern builders is increasingly drawn to this innovative method of space heating.

Warm baseboards in the house can serve as both the main and additional heating system in the house. They fit perfectly into the interior and often remain invisible to prying eyes. The width of such skirting boards is usually no more than three centimeters, and the height from the floor level is within 15-20 centimeters.

Install indoors warm plinth do it yourself much easier than, for example, underfloor heating. This does not require a concrete screed and other additional processes. At its core, a warm skirting board is a small heat convector capable of heating even very large rooms in a short period of time. In appearance, it is very similar to a regular plinth. Most often metal is used to create it. Heating occurs in three ways: water, electric and infrared. From conventional convectors, which used to be often installed under the windowsill, the warm baseboard differs in the way of heating. If the convector heats the room with the help of a convection flow, then the warm baseboard does this due to radiant energy, which has a positive effect on the human body.

Heating a room with a warm baseboard has several significant advantages:

The rooms will warm up completely. They will not have cold corners and walls that can become damp even at optimal air temperature when using conventional batteries.
A kind of thermal curtain is created near the window, which does not let cold air into the room. This is especially important at low temperatures outside, strong winds, and if a fairly large part of the surfaces in the room are glazed.
This method of heating will help save money on energy resources. This will be facilitated by the ray component, which will help to quickly heat the air with minimal energy consumption.
In such a system, there is no protruding node and various unaesthetic details, so it harmoniously fits into any room without losing its aesthetics.

How to make a warm skirting board with your own hands?

Each owner of a private house who has chosen the "Warm plinth" heating system for his house must decide whether he will install warm plinth do it yourself step by step, or purchase a ready-made system and simply install it. The second option will save you time and effort, but the first one is more financially beneficial. Another important decision to think about is the type of skirting board. The most popular are water and electric warm baseboards, lovers of everything new and unusual prefer to choose the infrared option.

The first thing you need when installing a warm baseboard is a tube, the diameter of which should be at least 1.6 cm. This diameter can be slightly larger, for example 2 cm. As for the material from which these tubes should be made, then here Suitable for both aluminum and copper. The aluminum version is more affordable, but aluminum has a very low thermal conductivity, so such a plinth will heat the room more slowly. Copper pipes are more expensive, but the price is worth paying, then it will pay off due to the high level of thermal conductivity of this material.

to install warm plinth do it yourself, you will also need a brass sheet about 3 mm thick. Instead, you can use aluminum sheet, or assemble a box from aluminum siding. If you find a large aluminum sheet, you can cut out all the necessary details for a warm baseboard from it. When installing a warm baseboard, remember that you need it to heat the room, not the wall. Therefore, all sections of the wall to which it will be attached must be insulated with thick plywood or drywall.

The radiator fins, which you yourself will cut out from a brass sheet, will subsequently perform two functions. They will be emitters and a carrier bracket. Therefore, they need to be cut in a U-shape. Later, you will screw the box bar to them. The bottom of these ribs should be bent outward at an angle of 90 degrees. Thus, you will get a platform for attaching the bracket to the insulating layer.

After you have a finished plate, you need to draw two axes along it - horizontally and vertically. To do this, you will need a compass meter. From the symmetrical horizontal line, you need to retreat another 4 cm in different directions and draw two more lines at these points. With a vertical line, you need to do the same, but you need to retreat by 4.5 cm. At those points where additional lines will intersect, you need to drill holes for the pipes. The easiest way to drill them is with a drill, the diameter of which will be half a millimeter larger than the diameter of the pipes you have chosen. If your drill is a few millimeters larger, it's okay, it will work too.

Having drilled all the necessary holes, bend the plate in the form of the letter p. You need to make markings on its legs, since it is with them that it will be attached to the wall. Stepping back three centimeters from the sides of the plate, it is necessary to draw two lines vertically. This is a mark for future folds needed to attach the system to the wall. The boundaries of the upper part of our "P" can be indicated by drawing two lines at a distance of 1.5 cm from the vertical line on its two sides.

If you do use brass sheet to make your own warm baseboard, keep in mind that it is not easy to bend it. You will need a special vise for this. Clamping the metal in a vise so that their upper edge coincides with the fold line, lightly tap with a hammer along this line until its edges drop - this is the maximum, it is unrealistic to achieve a straighter angle at home. But such a fold will be quite enough to install a warm plinth with your own hands without buying special materials for this.

The next step in the installation of a warm skirting board is the connection of radiator brackets with plywood, which serves as wall insulation. You need to connect them with self-tapping screws. Copper pipes are inserted into the finished holes and a warm baseboard is ready for commissioning with your own hands. When working on the creation of such a heating system, do not forget that drywall is a material that holds any type of fasteners very poorly. Therefore, even before you begin to install pipes, you need to put supports under all the brackets. Even a wooden rail is suitable for this. Each pipe must be fixed every meter with clamps using dowels. These dowels are not recommended to be driven into drywall - it will be much more reliable to fix them in the wall or its lining.

Next, the pipe loop must be looped and connected to a water source if you create do-it-yourself warm plinth water. For this you will need fittings. If you yourself can embed pipes into an autonomous heating system - excellent, if you are unsure of your abilities - better seek the help of a specialist. The most risky craftsmen use ordinary corrugated hoses for this. They are put on the end of a copper tube and tightened with a clamp. This option is quite dangerous and unreliable, therefore, if you have already decided to create a warm water plinth with your own hands, it is better to do it reliably. Think about how your loved ones will cope with the breakdown of such a system if it happens in your absence. It is especially impossible to take risks if there are small children in the house - they may not immediately understand the reason for the appearance of water in the room and damage their skin due to its high temperature.

Not only installing a warm skirting board with your own hands, but also when completing any other stage in the construction of your house, you should first of all think that all your actions are aimed at the comfort, safety and health of every person who will live in it. Therefore, even independent actions without the help of experienced specialists must be carried out in strict accordance with generally accepted standards and technologies.

Using the same hoses and fittings, you will not only connect your system to the heating, but also loop it. The ends of the copper pipes are connected in such a way that water can flow from one pipe to another, and then into the central system. Since you will most likely buy straight copper pipes, you will also want to bend them at home. To do this, it is customary to fill them with sand and bend around the steel column, plugging the ends. This is quite difficult to do - the pipes can tear or wrinkle, and water will circulate poorly at the places of kinks. Therefore, it is better not to waste time and effort on this losing task, but to use straight pipes, take high-quality hoses for corners.

Do-it-yourself warm electric plinth much harder to install than water. To do this, it is not enough to invest the heating element in a copper tube. It is also necessary to take care of insulation and waterproofing, to check whether the wiring in the house can withstand such an additional load. When installing a warm electric skirting board with your own hands, you need to be extremely careful, because any mistake can lead to a short circuit and even a fire. Each threaded connection in such a system must have a rubber gasket. Neither the radiator nor the copper pipes may touch the aluminum cladding. If you decide to install a do-it-yourself warm electric skirting board in your house, it is better to purchase all the factory-made ready-made parts and simply install them according to the instructions.

The general principle of creating warm skirting boards unites all such systems. But each of them has its own nuances and features that should be taken into account when creating a warm water plinth with your own hands. The specialists of the InnovaStroy company not only know how to make a warm plinth with their own hands, but also gladly share their knowledge with each new client. They are ready to create for you project of a private house go cottage the whole or that part of the project that you need in particular, including the installation scheme for warm skirting boards.

The warm plinth space heating system has long been studied and actively used by our architects when creating new buildings, if it suits customers. Thus, not only a new building equipped with modern heating technologies is obtained, but also material savings occur, which is important for almost all members of modern society. It is best to buy ready-made systems for installing a warm baseboard and install them using instructions. If this is a water type of skirting boards, the Thermia system from Ukrainian manufacturers is an ideal option. By purchasing a ready-made system, you will know that every detail and every connection in it is made in strict accordance with the norms, and your family will live not only in warmth and comfort, but also in absolute safety.