Fasteners for quick installation of interior doors. Benefits of interior door installation kits

The most important step in installing the door is fixing the door frame to the wall - the video below will confirm this. Weak fasteners, non-compliance with the level and other installation errors can lead to the canvas not entering the box or the door opening randomly. In the worst case, the whole structure will simply fall.

We suggest you explore several installation methods, and choose for yourself the one that seems to you the most optimal in your situation.

If you are replacing an old door with a new one, after removing the trim, carefully dismantle it with a nail puller, after sawing the box and pressing it away from the opening. Firmly seated old fasteners for the door frame can be cut down with a grinder.

Then it is necessary to examine the slopes for their strength, and the walls adjacent to them - for verticality and evenness. Inconsistency with the level and curvature of the walls will lead to the fact that visually the door will seem to be placed crookedly, and the platbands will not adhere to the plane of the walls.

Therefore, all the shortcomings should be tried to be corrected at this stage with the help of plaster or cladding along the frame.

In addition, even before the start of installation, you should make sure that the door leaf will enter the opening not only in width, but also in length. The instruction says that there should be a gap of about 1 cm between it and the floor. Keep this in mind if the floors have not yet been leveled or the flooring has not been laid.

Note. The opening should be slightly wider than the outer dimensions of the box. If this is not the case in your case, you will have to expand it or choose a different door model.

If the opening is too wide for the selected door, it will have to be reduced by bricking it or by embedding a drywall box in it. It is not recommended to leave a large gap and fill it with mounting foam. This will weaken the fixation and make it problematic to fix the skirting board at the door frame.

Mounting methods

There are several ways to fix the door frame in the wall opening. Each of them uses its own type of fastener. And each of the options provides a certain level of strength and reliability of the structure.

The choice of method depends both on the material of the walls and on the weight.

Foam mounting

The algorithm for performing work is simple:

The assembled box with a hinged door leaf is inserted into the opening and fixed in it with wooden wedges;

The building level determines its correct position relative to the vertical. Moreover, the level must be applied to two adjacent faces: inner and side;

Spacers 3 mm thick are inserted between the frame and the closed door on top and on the sides;

Advice. In order not to stain the canvas with foam and not damage it, you can use spacers made of wooden slats or special adjustable fixtures instead.

Mounting foam foams small areas between the wall and the box;
When they dry, the entire perimeter is filled with it. You can’t do this right away, because, expanding, the foam will put pressure on the box. Foaming the perimeter, you should not fill it completely, initially half the volume is enough to leave room for expansion.

To install a swing interior door, you will need quite a lot of materials and tools. Moreover, depending on the state of the opening, the nature of the wall, the weight of the sash, and so on, both fasteners and tools may need different ones.

The assembly kit for installing interior doors is a universal kit, since it not only includes the parts necessary for installation, but also determines a certain technology.

Mounting kit

Under the complete set of the door, as a rule, they mean fasteners, accessories - a lock, handles, some additional elements - platbands, racks, and so on. Their composition is different, but mainly due not to the fastening of the door frame and sash, but to the future functionality and appearance of the door unit.

Fasteners and tools for the home master have to find on their own. The kit for the interior door ensures the installation of any hinged sash in any state of the opening. How is this possible?

The kit consists of several universal and simple devices, the correct combination of which, however, allows the installation of any kind of product. Mounting kit includes:

screw M6 - 6 pcs;
nut M6 - 6 pcs;
bracket - 6 pcs;
washer 6 * 16 - 6 pcs;
dowel 10 * 50 - 6 pcs;
self-tapping screw in 16 mm - 12 pcs;
instructions explaining in detail how to install the installation kit for interior doors.

In addition, for installation, you will need two open-end wrenches for a 10 mm nut and a drill with a diameter of 10 mm.

The composition of the set may vary somewhat - not due to the number of elements, but due to the arrangement of brackets. In the catalogs, you can choose any suitable option. In the photo - a set for installing an interior door.

Benefits of the mounting kit

The set consists of several fasteners of a certain configuration. In fact, it is the form that is the basis of the fastening technology. In the catalog you can find different options, but their application is the same - universal.

Profitability - the cost of a set from the catalog is in any case lower than the cost of all elements that are selected individually.
There is no need to take into account the features of the wall. Even the level of the floor does not really matter.
The mounting kit for the interior door involves a hidden installation, and this method retains the original appearance of the finish.

There is no need to level the floor and walls, fix additional planks or process slopes, which also reduces costs.
Numerous devices for temporary and permanent fixation are not required: wooden wedges, spacers, planks, etc.
All operations require only 2 open-end wrenches and a drill

Mounting technology

The assembly kit is divided into 2 parts, which allows the noisiest part - installation of fittings, for example, to be carried out in a utility room, and the frame and door to be installed indoors. You can choose a mounting kit for interior doors from the catalog or in the store.

The technology of use is very simple.

Assemble the box: for this, the bars are trimmed, and there is no need to cut them at an angle of 45 degrees. The upper crossbar is simply fixed to the side racks.
Holes are drilled under the fasteners, and then the bars are connected with self-tapping screws.
Fittings are fixed by a method determined by its structure. Door hinges can be very different.
In the opening, the places for fixing the bolts are marked: 3 vertically and 2 horizontally. It is desirable that the distance between them be the same.
Drills 10 mm holes for the bolt and 6–7 cm deep. Dowels are driven into the holes.
Then the fastener is assembled - a bolt, a washer, 2 nuts. Bolts are screwed into dowels.
By measuring the width of the box and adding 16 mm, the required width between the bolts is obtained. Adjust the distance between fasteners on opposite side posts.
The frame is inserted into the opening, leveled. Mark the fixing points for the brackets.
Remove the box and fix the brackets to the marked places.
Install the side stand - hinged, with brackets on the bolts, fix with a nut. Align the frame, and then, tightening the second nut, tighten or unscrew the bolts. Adjust the position and fix with a nut.
The same is done with the second rack. Then they hang the interior door and, if necessary, re-adjust the position of the structure by tightening the nuts or unscrewing the bolts. After checking the level, the fasteners are finally fixed with nuts.
The voids are filled with mounting foam. After drying, the excess is cut off and platbands are mounted.

The video on how to install an interior door using a mounting kit is described in more detail.

Possible options for fixing doors in the opening

Working with mounting foam
New mounting options

Each master is faced with the problem of how and on what to fix the assembled doors. To install the finished door block, it is possible to use various installation methods. Knowing these installation options, you can easily choose the right one for yourself. You will need a small set of tools such as a drill, hammer, level, screwdriver and hammer. Also, to directly fix the box in the opening, you need fasteners and mounting foam. Depending on where you need to fix the door block, you may need self-tapping screws, dowels, anchors.

The main stages of installing a door block

At the very beginning, the old door frame is dismantled. It can be carried out using a nail puller (crowbar), having previously made cuts on both sides of each vertical bar, in order to then squeeze this structure from the opening. If anchor bolts were used during the installation of the old box, nails that cannot be unscrewed can be cut off using a grinder.

Before installing the interior door frame, it is necessary to check the verticals of the sen and take into account the differences in the level of the walls and floor. The door frame must be positioned so that if there are irregularities, the wall box does not deepen in the opening. This is necessary to fit the door trim. In order to correctly position the door frame, you should use the building level and take into account all the opening errors.

First of installation, the assembled door block is rigidly fixed in the opening in order to achieve the initial level of rigidity, wedges are used. After completing the fixing work, it is worth re-checking the correct location of the level so that the box is level with the door.

Working with mounting foam

It is important to know that the foam that is designed for the gun is much better and more convenient to use due to the fact that it is more dosed and has a small expansion coefficient, it freezes much faster. Foam, which is fed with a straw in a large amount, it will expand longer. Before starting work, it is better to cover the door leaf with masking tape and film, because the foam is difficult to wash. It is important to know that you need to start foaming with the fixation of individual small sections. After 30 minutes, you can already go through the entire perimeter. All cracks are filled with foam (50% of the total volume). Do not fill with a large amount of foam, because during expansion the foam will squeeze the box inside. We recommend using professional foams.

Since the tree shrinks and expands precisely because of the increased humidity, the consequence of the expansion is the deformation of the door block. The door simply stops closing for this reason.

on possible ways of mounting doors

There are several ways to fasten the door frame in the opening, each of which involves the use of a special type of fastening. Various fastening options provide a certain level of reliability and strength of the fixed structure. We hope that the videos on the options for installing wooden door frames will help you.

: Mounting a door frame made of wood and MDF in the opening

Hidden way to install doors on foam

The door frame is fixed in the opening, wooden wedges are used for fixing, and the correct location is checked by the building level. Foaming with mounting foam should be done little by little, in sections and with interruptions to avoid deformation. The door frame is kept almost thanks to the foam alone.

To keep the gap between the frame and the door itself, use small 3mm spacers that are inserted between the door and the frame. They can be removed only when the foam dries. Usually the door is left overnight.

This method is convenient if you do not need to go into the room, it is fast and does not require much effort. It is important not to overdo it with foam so that you can open the door.

Installing doors with clamps or spacers

The principle of installation lies in the fact that we use inside for temporary fastening of the door block in the opening of the spacer. It can be both ordinary wooden rivers and special adjustable devices.

Both of these methods are very good for light and small doors.

: Template for installing door frames.

Fastening doors with Knauf hangers

For these purposes, Knauf's direct suspensions, which are used in suspended ceilings, are the best fit.

First you need to screw the plates to the box;
Insert the door into the opening;
We adjust the level;
We mark the places for the recess in the wall;
We make a selection for the plate:

After that, we set according to the level and fix the plates. For adjustment, we use wedging with wooden blocks.

It is also necessary to take into account that with this method of mounting the box on the outer part of the wall, the place of the recess will definitely need to be hidden under a layer of plaster. That is why, this method is only good when there is no fine finish.

: Installation of an interroom deaf door from the Senator company

New mounting options

This will let you know how to fix the door frame in the opening. This type of fastening is the installation of an interior door frame by putting the box on the screwed-in heads of self-tapping screws that are located at the ends of the opening. This happens with the help of metal plates with a hole, which are screwed on the outside of the box.

To achieve the final fixation of the frame in the doorway, the usual means of adjustment are used.

With this method, the racks of the door block move freely in the opening.

A clear advantage of this method is the full possibility of adjustment and, at the same time, rigid fixation while maintaining the original appearance of the box and the exterior finish of the wall.

: New technology for quick installation of interior doors

Concealed installation, fastening under hinges

As a rule, for the rigidity of the structure, screws or anchors are used, which are hidden under the hinges. To do this, a hole is made between the screws in the loop and fastened through it to the wall. From the side of the lock, another mount is attached under the decorative plate. As a result, we get 3 fixation points.

After fixing directly, we put a spacer at the bottom of the doors, since the bottom is not fixed and fill all the gaps with foam.

A: Foaming the door frame and a few tips.

Through-hole fastening on anchors or screws

This is the most common standard installation option for interior doors. For this mounting option, first holes are drilled for anchors in the right places of the racks, then the door is fixed in the opening.

Marking 4 anchors on each side;
Drilling with a pen 14mm to a depth of 10mm (place for a plug);
We drill a through hole with a 10mm pen (a place for fixing with an anchor):

After that, the box is exposed and the concrete under the anchor is drilled with a 10mm drill. When the box rests on its anchors, it holds securely and does not require any spacers. The attachment points can be hidden by installing decorative caps of the desired color, size (14mm). Instead of anchors, screws can be used, this will reduce the diameter of the plugs. The use of this option is the most reliable for heavy doors. With it, you can align (stretch) a curved rail. Doors can be used almost immediately. It is possible to adjust the gap. The downside is the presence of stubs.

: Door frame installation method with end caps

Tricks when installing door extensions

: Milling a quarter on the door frame / How to install an extension if there is nowhere to put it

There are many options for installing an interior door frame, but you should choose the one that is the easiest, most convenient and reliable, or the fastest. The choice can be made according to any method of door installation, but these methods can be affected by which opening the installation takes place, take into account the intensity and other factors.

New Section Entries

Ideas for using glass doors in an apartment

Sliding plastic doors for balconies and loggias

How to choose a door to the balcony and install

How to choose and make a mosquito net

Adjustment of plastic doors

Installation of sliding interior doors

How to choose an office front door

Replacing a door in an apartment is quite common. Such a thing, of course, is not very simple, but if you try, then everything can be arranged in the best possible way without much difficulty.

The door frame serves as a frame for installing the entire door structure as a whole.

There are many difficult moments in fastening the door, according to experienced specialists, one of the most difficult is fastening the door frame.

With strict adherence to the instructions, everything can be done in a fairly short time, and the quality of work will be high. So, how to fix the door frame correctly, so that the door does not soon become unusable. The tools that are needed for this are the following:

Plumb.
Building level.
Roulette.
Hammer drill.
Nails.
Screws.

Do-it-yourself door fixing process

The first step is to carefully complete the assembly process of the straps that secure the door frame. When this procedure is completed, you need to start installing the box in the doorway. The 3 pieces of the door frame must be stacked on the floor. After that, the door stop is installed. Strappings that have been pre-connected must be secured with nails (it is highly recommended to use nails that are 75 mm long), and a round section is also needed. A small gap should be left between the door frame and the wall, which can be filled with thermal insulation material. Horizontal and vertical surfaces must also be filled with this material.
In the gap that exists between the two strappings, it is necessary to nail a bar that has a cross section of 50 by 25 mm. It must be installed at the bottom of the box. Such a bar is necessary so that the parts of the box remain in a parallel position during the entire fastening of the box.
After the door frame is assembled, it is necessary to begin its fastening in the doorway. It is very important that its location is exactly in the center. In this process, you need to pay attention to checking the verticality and perpendicularity, you must use a plumb line, level and square. If necessary, a seal can be installed. The door frame should be fixed well and easily, it must be done in those places where there will be contact with the wall, for this you need to lay plywood pieces. After the process comes to an end, you need to check again how vertical the side elements are. The fastening of the box to the fixing bars must be carried out with nails (their length is 65 mm, such nails must be without a hat). In the event that the wall is made of stone, then the best option is to use screws 65 mm long. After that, the nailed bar is removed. You need to check how exactly horizontally the top harness is. If the need arises, the situation can be corrected.
For proper hanging, the fastened parts of the doors must be disconnected, after which installation should begin on previously prepared places, they should be on the door. When the door is installed in the door frame, lining must be placed under it, after which the installation of the remaining parts of the hinges begins. At the end, the axles are installed in the appropriate places.

How can the door frame be attached to the door leaf?

If there is a need to fix the door frame together with the door leaf, then such work can also be quite easily done independently:

The process of installing the door block: a - alignment; b - fastening; in - a hinge plate of a door leaf; 1 - level; 2 - jamb; 3 - top; 4 - door leaf; 5 - loops; 6 - personal; 7 - partition rack.

First of all, on the vertical elements of the box, the lower border of the door leaf is indicated (this is done with a pencil). After that, the canvas is removed from the hinges and the box is installed in the hole. In order to make the spacer of the box, it is necessary to use two wooden planks, which must be of the appropriate length. The slats that are inserted at the top should fit between the vertical members of the box with some difficulty.
Now you need to start the process of leveling the door frame. It is important to note that it must be in a strictly vertical position. Plumb and level in this regard are indispensable tools. In order to be able to effectively adjust the position of the box, it is necessary to use wooden planks, if necessary, they can be placed under the vertical elements. With all this, it must be taken into account that the door leaf must close without difficulty (as well as open), a gap of 5 mm must be left between the frame and the lower edge of the leaf. In order for all this to be done with maximum clarity, it is necessary to make preliminary marks on the lower border of the door leaf.
Now you need to start installing the wedges. In the best way, the box can be fixed with wooden wedges. You can use wedges that are used when working with laminate. Installation must be done to the floor, approximately to the height of the spacer bar. At the same time, special attention must be paid to the vertical elements of the door frame, their installation must be carried out clearly vertically. The building level in this regard will provide invaluable assistance. There is always a gap between the box and the wall, and so, on both sides this gap must be the same.
It was the turn of the final fixing of the door frame. Frame dowels made of metal in this regard are the best fit. They are carefully inserted through the hole into the box that is in the wall. It should be noted that the wall holes must be made through the holes that are in the box. In this regard, it is best to use a high-power impact drill, which has a drill that can drill through concrete.

After completing the installation of the door frame and leaf, it is necessary to install fittings.

After the work has come to an end, it is necessary to check how tightly the door leaf fits into the box. It is necessary to check whether the gaps are sufficient, if they are insufficient, then it is necessary to tighten the screws.

Modern hardware stores offer various types of wooden door frames. They can be treated with a paint and varnish coating, but this is not necessary. The coating has the following advantages: protection against scratches, fading and fading, resistance to chlorinated compounds.

It should be noted that wood is such a material that can “forgive” many mistakes. That is, such errors can be easily corrected even by non-specialists.

If the box is made for painting, but not yet covered with paint, then it is best to install and fasten it with plates.

Then the upper cross-section is wedged from two edges, then the door is hung, the spring is checked. It should be noted that if the bend is carried out towards the canvas, then another suspension plate can be installed in this place, with its help the cross section is stretched towards the volume. The base of the box can be drilled, for this you can use an ordinary self-tapping screw, its head must be recessed into the box, then everything is hidden with putty (an acrylic sealant can be used instead, but only one that matches the color scheme perfectly). After painting is carried out, all these places will be securely hidden, the place of the installed anchor will not be given out in any way.

It should be noted that even the door frame that is already painted can be fastened in this way. But this can only be done when there is complete confidence that all anchor landing sites will be most carefully hidden. In this regard, you can use colored putty, which is similar to the color of wood, you can also use colored sealant, in the end you need to use paintwork, but it should match in color, then the door frame can be installed so that it will be beautiful.

To quickly and conveniently install interior doors, you can use a special mounting kit that will greatly facilitate the installation process. Both experienced craftsmen, and, especially, beginners, argue that it is much more convenient and easier to mount doors using a kit. In the article, we will consider the features of the mounting kit, find out what is included in its composition. And also find out at what price you can buy this useful accessory from different manufacturers.

Description of the mounting kit for quick installation of doors

Mounting kit consists of two parts: the first is attached to the door frame from its inside, and the second part is attached to the wall of the doorway. By connecting the parts of the hardware system with each other, it becomes possible. And, besides this, you can adjust the evenness of the box with the canvas already installed.

You can make adjustments and check the evenness of the installation at any stage of work: and at any stage it will be possible to correct the “jamb”, if any. At the same time, the savings in time and effort are significant.

You will learn how to install a convenient handle with a lock for an interior door.

pros

Find out what are the advantages of the installation kit for installing doors.

Although outwardly the kit looks like just a set of fasteners, in fact it is a well-thought-out “from and to” door installation technology. And the detailed instructions attached to the kit will allow you to install the doors even to a person who is far from such activities.

Using the kit allows you to significantly save on the purchase of fasteners, as well as save nerve cells and time. The kit already includes all the accessories and necessary elements for mounting the door frame.

What to do if the key is stuck in the door lock will tell you.

All mounting kits are concealed fasteners. They do not require through drilling of the box. Does not suffer from their presence and door decor. At the same time, the kit allows you to fix the box in six places, which makes the finished product securely and firmly fixed.

Thanks to this device, standard training, which usually takes a lot of time and effort, can be excluded from the work process. This greatly simplifies installation and saves time.

Among the work that will not be needed when using the mounting kit are the following:

adjustment (more often - reduction) of the opening area;
strengthening the walls of the opening;
floor level adjustment and other types of work.

This reduction in work steps reduces installation costs, resulting in significant time savings.

One of the indisputable advantages of using the installation kit is the ability to quickly and easily dismantle the old door, and just as quickly fix the new one in its place. In this case, it will not be necessary to destroy the opening, since the new door is hung on the remaining fasteners from the old one.

The versatility of the fasteners included in the mounting kits allows you to use it to install doors of various sizes and modifications. In addition, the mounting kit will cope even if the door frame is noticeably skewed.

Read how to open the front door lock without a key.

Using the mounting kit, it is easy to install doors into wall openings from a variety of materials:

tree;
bricks;
concrete;
drywall;
foam concrete, etc.

When using such a set, the need for spacers, wedges, and other types of temporary fixation of the box disappears. Adjustment is carried out using open-end wrenches, available in literally every home. If, nevertheless, an open-end wrench was not found, you can also use pliers to tighten the adjusting screw.

Well, if the gap between the door frame and the opening is insignificant, then one nut can be excluded, leaving 5 attachment points. This method allows you to reduce the clearance to 10 mm. Due to reliable fixation, the service life of the door block is significantly extended.

Due to the fact that when using mounting kits for installing doors there is no need to “foam” the gaps in the box, the reliability of the fasteners increases. In addition, the specified parameters of metal brackets do not lose their relevance even after a few years, which will ensure the evenness of the box. The foam used in normal installation can begin to crumble, lose rigidity, so the benefits of using metal fasteners are obvious.

It is possible that information about overhead locks for an entrance metal door will be useful to you, which will help you understand.

Metal fasteners securely hold the box in the opening, so even after the voids are filled with foam, the box does not “mangle”.

When the door is installed in the usual way, it can only be used after the foam has completely cured. And when using the metal fasteners of the mounting kit, this opportunity appears immediately after completion of work. For some rooms (bathroom, toilet, kitchen) this advantage is very important.

What is included in the set of accessories for the interior door frame

Find out what components are included in the installation kit for installing doors.

The kit includes detailed instructions, following which you can competently and quickly cope with the door installation.
A special universal key that allows you to quickly deal with the fixation of all fasteners. They can tighten all the nuts included in the kit, which is also “at hand” to the one who is engaged in the installation. You may also be interested in information about .
Nut with collar. This fastening element makes it possible to firmly fix the door in six different places, which ensures much greater reliability of fastening. Some manufacturers also offer special nuts without washers, which make the installation process even easier.
A screw with a press washer - also in the amount of six pieces.
Plastic dowels - 6 pcs.
Low nut - 6 pcs.
Self-tapping screws of a certain size (usually - 16 mm) - in the amount of 12 pcs.
Hexagon head bolts allow for a secure and durable fixation of the door frame.
Mounting bracket - 6 pcs. This element allows you to adjust the evenness of the installation of the door frame with a minimum error. In this case, the adjustment can be carried out with the door leaf already installed.

Features of mortise locks for wooden entrance doors are described.

Manufacturers and prices

We will find out at what cost mounting kits for installing doors from different manufacturers are offered today.

Creepdver Company offers high-quality mounting kits from economy class to the "Special" level. So, the economy option for 400 rubles is perfect if the weight of the door leaf does not exceed 50 kg.

But the “universal” set is more popular, which is also suitable for doors of the same “weight category”, however, it includes a special curved key. The last tool allows you to quickly cope with adjusting the gaps and fixing the brackets. The cost of the "universal" kit is 420 rubles.

For massive heavy interior doors (for example, oak), the company offers a variant with reinforced brackets. The cost of the "special" set is 495 rubles.

Domestic manufacturer "Ocean» offers mounting devices for installing doors at a price of 400 rubles. Minus - a curved wrench is not included in the package. But if you do not take this drawback into account, in general, the quality of fasteners is decent and quite competitive.

You can also read the material on how to change the lock on the front metal door,.

By the way, if you search well, you can find offers and even at a price of 100 rubles per set. But in this case, a minimum order amount of 500 rubles is required. The quality of such kits causes logical caution, so it's better to pay more, but get a guaranteed quality product than to become the owner of five faulty kits.

Video

Mounting kit for installing doors:

We examined the features of using the installation kit for installing interior doors. As you can see, this device is, without a doubt, a very useful thing, saving time, effort and money. In addition, the mounting kit makes it possible to cope with the work even for a beginner. Therefore, if you are going to change the doors inside the apartment, do not forget to purchase this useful set of fasteners, with which you can get the job done in a short time.