What blocks can be used to build a bath. What is better to build a bathhouse from: general information, features and recommendations, which bathhouse is better to build

Own bath in the courtyard of a private house or is the dream of many owners of suburban areas. Everyone knows that the bath serves as a place not only for regular washing, but also for wellness procedures - healing steam cleanses the pores, improves blood circulation and gives vitality. In addition, there is a tradition that this particular building often turns into a kind of “club”, where you can have such a great time with friends or relatives.

Therefore, before the owners planning to create such a useful “complex”, the question inevitably arises - what is better to build a bath from, so that it can be created and maintained an optimal microclimate at any time of the year and at no extra cost. The choice of material directly affects the creation of a healthy, relaxing bath atmosphere.

In addition, the right material is the key to the durability of this structure. It is imperative to take into account the fact that the inner surfaces of the walls will be constantly exposed to humid hot air and temperature changes.

The modern market offers a wide variety of different building materials suitable for building walls for houses, utility, utility and other specific buildings. However, it is worth considering in more detail and figuring out which one is ideal for a bath.

Initially, "towns" - wooden chocks - were used as point supports. But over time, any wood rots and needs to be replaced, so it was replaced by concrete structures.

This type of foundation is good because its device can smooth out the unevenness of the site: it is enough to deepen a number of bases to the desired level to obtain a flat area. It can be used in the construction of small one-story baths.

pile gained great popularity, especially due to the fact that screw piles can be installed even in winter. Therefore, the construction of other types of baths, for which such a foundation is suitable, can be started at any time of the year.

The bottom line is to twist specially made piles at regular intervals (the distance between them is regulated depending on the massiveness and size of the building).

Pile foundations also include foundations made of bored piles, we recommend reading about this, as well as about pile foundations in general.

What is better to build a bathhouse from: the main question is the walls

Wall material directly determines:

• type of foundation required;
• types of insulation and their application (outside or inside).

Therefore, it is so important to deal with the walls in the topic “What is it better to build a bath from”.

Blocks: what material?

Block baths have won love among builders and buyers for good reason: they are distinguished by incredibly short construction times with a relatively low cost. If you have a certain amount of skills, you can independently cope with the construction of a bath from blocks. The most common types of blocks are:

1. foam concrete;
2. expanded clay concrete;
3. aerated concrete;
4. gas silicate;
5. cinder blocks.

Block baths need a decorative finish, because. do not differ in special aesthetic qualities in a "pure" form.

From what blocks is it better to build a bath?

Ease of manufacture cinder blocks leads to the development of handicraft production, which cannot meet the standards of production. However, they undoubtedly have one plus - a low price.

gas silicate blocks have high hygroscopicity, require high-quality hydro and vapor barrier, in addition, it is important not to make a mistake in its types: they all have different parameters for strength and thermal insulation. The use for the construction of a bath is not always justified.

Therefore, answering the question: from which blocks it is better to build a bath, we say: they are well suited aerated concrete and foam concrete They are easy to use, light weight and easy to process. The cellular structure guarantees excellent thermal insulation properties, but also needs high-quality vapor barrier and waterproofing.

Wood

Wood is one of the most traditional materials that meet all environmental requirements. Today, the industry offers different types of processed wood:

1. log(the most solid material);
2. beam(processed wood of certain dimensions, for example: 100*100, 200*200);
3. carriage(a log hewn from two opposite sides - especially popular in the Scandinavian countries);
4. double beam(represents 2 boards with grooves between which a heater is placed, most often mineral wool or ecowool).

What wood is better to build a bath?

The main division of wood building material lies in the nature of the logs used: resinous (coniferous) or non-resinous (deciduous) species.

What wood is better to build a bath? From dense and well dried. Aspen is one of the non-resinous species, but such wood is very expensive, and oak is especially expensive. The fundamental difference is that a poorly dried coniferous forest will tar for a long time (resin smudges will form).

Therefore, most often they are built from pine and other conifers. In addition to a lower price (compared to the same aspen), they have such advantages as:

1. smooth and straight trunk;
2. easy processing of a log;
3. knots do not spread inside the wood (as, for example, in birch);
4. keep heat well (aspen is significantly inferior in this characteristic).

In view of the foregoing, if you chose pine as an answer to the question: what tree is better to build a bath from, then you should give preference to a well-dried forest.

From which forest is it better to build a bath? It is desirable if it is a winter forest(i.e. chopped in winter and dried during the summer under cover).

REFERENCE. Dead wood is periodically offered as a building material, and this is justified to some extent, such wood has a high density. But it requires special treatment with antiseptics, otherwise there is a great chance of damage by rot in places of high humidity.

Timber or log: what to make a bath from?

Each of these materials has its own advantages:

• log bath does not require additional thermal insulation, except for interventional insulation;
• a bath from a bar it is easier to fold than from a log, a minimum qualification is enough to lay a beam with minimal gaps.

Therefore, when choosing a material and what to make a bath from - use the additional information from.

What kind of timber is better to build a bath?

For the construction of a bath, it is best to use a well-dried timber: it will shrink less, in addition, there will be a lower risk that the timber will begin to bend. The increased humidity of the timber reduces its heat-insulating properties.

What kind of timber is better to build a bath? For, based on the type of wood from which it is made, you can use the table below:

wood species	Shrinkage ratio, %		Mechanical strength for wood with 15% moisture content, MPa (kgf/cm²)
	in the radial direction	in the tangential direction	in compression along the fibers	bending	chipping
					in the radial plane	in the tangential plane
Coniferous tree species
Pine	0,18	0,33	43,9	79,3	6,9 (68)	7,3 (73)
Spruce	0,14	0,24	42,3	74,4	5,3 (53)	5,2 (52)
Larch	0,22	0,40	51,1	97,3	8,3 (83)	7,2 (72)
Fir	0,9	0,33	33,7	51,9	4,7 (47)	5,3 (53)
Hardwood tree species
Oak	0,18	0,28	52,0	93,5	8,5 (85)	10,4 (104)
Ash	0,19	0,30	51,0	115	13,8 (138)	13,3 (133)
Birch	0,26	0,31	44,7	99,7	8,5 (85)	11 (110)
Maple	0,21	0,34	54,0	109,7	8,7 (87)	12,4 (124)
Elm	0,22	0,44	48,6	105,7	–	13,8 (138)
Elm	0,15	0,32	38,9	85,2	7 (70)	7,7 (77)
Softwood tree species
Aspen	0,2	0,32	37,4	76,6	5,7 (57)	7,7 (77)
Linden	0,26	0,39	39	68	7,3 (73)	8 (80)
black alder	0,16	0,23	36,8	69,2	–	–
black aspen	0,16	0,31	35,1	60	5,8 (58)	7,4 (74)

According to the results of many studies, a double beam is ahead of similar indicators for a conventional beam, but the use of mineral wool as an internal insulation casts doubt on its use in the construction of a bath.

Useful video:

Watch a video explaining the advantages of a double beam. It seems reasonable to conclude that the technology is more suitable for homes than baths.

For a good warm bath, it is best to use a bar 200 * 200, the use of a thinner bar or half-bar (for example, 100 * 50) will require significant financial costs for external insulation. Although, if the bathhouse is heated only in summer (country option), then not thick walls, 10 centimeters, may be enough.

Foam block

As already mentioned, it has a high ability to absorb moisture due to its porous structure, therefore competent vapor and waterproofing is required. You can read about the advantages and strengths of a foam concrete bath in these articles:

• , as well as .

Frame baths

They gained great popularity due to the short construction time, as well as others that allow them to be carried out. Caution should be taken when choosing a heater for the frame, since the bath is a building with a high temperature regime of use. Therefore, the insulation must be safe and not emit harmful substances when heated. You can read more information in this article:.

The choice of the type of foundation for frame baths is devoted.

Warming

It was not for nothing that log baths were so popular, because before there was no such assortment of heaters, so everyone managed with a simple caulk: plugging cracks and gaps with natural materials: moss, flax, etc.

Baths made of timber already require little insulation from the outside, especially in areas in cold winters.

But during the construction of block and brick baths, you can’t do without insulation at all.

What needs to be insulated in any bath?

In any bath, no matter what building material it is built from, it is required. This is no accident: after all, warm air always tends to rise. If the ceiling is not insulated, then all the heat will go outside. baths. Frame baths have insulation already inside the frame, so additional insulation is appropriate if you are in an area with extremely cold winters. More .

Floor

Any floor needs to be insulated, especially if the foundation has not been thermally insulated. Depending on the organization of the floor in your bath (pouring or non-pouring), the choice of insulation depends. If the floor is pouring, then the insulation must be protected from moisture, otherwise it will lose all its properties when wet. More information .

Roof

Roof insulation will be needed if you organize an attic floor, in this case you can use foam or mineral wool.

Insulation from inside or outside

Most often, insulation is done from the inside, log baths and baths are insulated from the outside, which are used in winter in cold regions. often combined in decorative trim. creates the effect of a thermos and protects the wall material from damage by high temperatures. It should be remembered that .

A little about heaters

It must be understood that it is impossible to purchase a batch of one type of insulation and use it to insulate the entire bath.

This topic is the subject of heated debate, which only flares up brighter with the advent of another new product on the heater market.

From what to make a bath quickly and inexpensively?

From what to make a bath quickly and inexpensively? Choose one, or build your own from timber or. These materials require minimal skill and skill. The use of natural insulation will also reduce the cost of the project.

They are also popular because of their cheapness and ease of execution, we recommend that you familiarize yourself.

Conclusion

It is difficult to give an unambiguous answer to the question: what is better to build a bath from, as you can see, the choice is huge. It is worth focusing on your personal preferences and budget possibilities. We have tried to provide you with a detailed section of information that will make it easier for you to understand this difficult topic and find the solution you need.

Building a sauna from blocks is an economical alternative to wooden construction. Using this option allows you to reduce the time of work and reduce labor costs. Since this is a large group of materials, let's try to figure out which blocks are best for building a bath.

What is the nature of the bath?

The material used for the construction of such objects must have the following properties:

1. Low thermal conductivity. The lower the thermal conductivity of the material, the more efficient the bath: it warms up faster and cools down more slowly.
2. Water resistant. The Russian bath involves the intensive use of hot water vapor. Not every material is able to maintain its structural properties for a long time under such conditions.
3. Resistance to temperature changes. Heating followed by cooling leads to accelerated wear of structures. This phenomenon is most noticeable when using a bath in the winter.
4. Environmental Safety.

Options

Existing types of blocks have a high level of thermal insulation and relatively low cost. Consider the specific features of the various options.

aerated concrete

This is a material based on foamed concrete, produced in industrial conditions with mandatory autoclaving. The thermal conductivity and strength of this option depend on the density. The higher the density of the material, the higher the strength, but the lower the thermal conductivity. Therefore, for compact baths, it is advisable to use low-density aerated concrete, and for large projects - high.

Advantages: dimensional stability and ease of processing. Aerated concrete is laid on glue, which eliminates cold bridges and improves insulating properties.

Cons: ability to absorb moisture. As a result of the accumulation of moisture, the performance properties of the material deteriorate.

gas silicate

The technology for the production of this material is identical to the technology for the production of aerated concrete. The difference is that the main component of bock is not cement, but lime.

Gas silicate is characterized by an even higher hygroscopicity, and therefore is not very suitable for the construction of Russian baths.

foam concrete

A simplified version of aerated concrete. For the production of foam concrete, industrial conditions are not needed, which allows you to produce the material yourself.

Pros: low cost.

Cons: variation in size and the risk of getting low-quality material.

cinder blocks

This is a material based on concrete and wood waste. The share of waste can reach 90% of the volume of the block. Hence the low cost and availability to all segments of the population.

Cons: discrepancy in size, low load-bearing properties, controversial level of fire safety. It is advisable to use cinder blocks in conditions of austerity and independent production (so you will be sure of the quality of the material).

Expanded clay concrete

An improved version of the cinder block, where expanded clay is used instead of waste. This approach increases the strength of the block and makes its properties stable. Expanded clay concrete poorly absorbs moisture and tolerates low temperatures, as well as sudden changes.

ceramic blocks

In fact, it is an enlarged brick with a high volume fraction of voids. The material is characterized by high performance properties and price.

Conclusion

From what blocks is it better to build a bath? According to the combination of performance properties and cost, the best option is aerated concrete and expanded clay concrete. If you can afford the use of ceramic materials, then you should consider using traditional wood.

Traditionally, a bath is built of wood, but today it is very difficult to find a good master carpenter who can competently build walls, and very expensive. Therefore, building blocks are increasingly used for the construction of baths. There are many types of them today, they have advantages and disadvantages, but their main advantage is that having at least some construction experience or builder friends, you can independently fold walls and piers. And since most of the blocks are lightweight, it means that the foundation can be made lightweight, which saves time, effort and money.

• 1 Types of blocks, their characteristics and features
• 2 Ceramic blocks
• 3 Features of building a bath from blocks
• 4 Reviews of the owners of baths from blocks
• 5 Conclusions

Types of blocks, their characteristics and features

aerated concrete - refers to cellular concrete. It is made from cement, special foaming agents and quartz sand. This composition is poured into molds, water is added. As a result of the reaction, foaming occurs and the mass fills the mold. To give the material greater strength, the resulting blocks are treated with steam in special autoclaves. At high pressure, under the influence of steam, quartz sand forms new strong bonds. In fact, it is a synthesized artificial stone of high strength.

Aerated concrete block. The color of the block is closer to gray, so the main filler is cement

For the construction of load-bearing walls and partitions, it is advisable to choose autoclaved aerated concrete, and non-autoclave can be used for insulation - it is cheaper, but its strength is lower. Aerated concrete blocks come in different densities:

• from 0.3 to 0.5 t/m3 is used for thermal insulation;
• from 0.5 t/m3 and above (up to 1.2 t/m3) can be used for building walls.

For the construction of small buildings, you can use aerated concrete grade D500 (density 0.5 t / m3) - it may well serve both for the construction of the box and for the construction of partitions, but it costs much lower than grades with a higher density. When erecting the walls of the bath, for less consumption of blocks, they are placed on the edge, so the wall thickness is about 200 mm. This is quite enough, since the block holds heat well, especially since the walls will be insulated.

Bath from aerated concrete blocks. Block placed on edge

The advantages of aerated concrete are relatively low weight, ease of processing (it can be cut with a hacksaw or drilled with a conventional drill), does not burn and acquires greater strength over time. Disadvantages - relatively high hygroscopicity when using low-quality material and a rather high price. In order to reduce the amount of absorbed moisture, special additives are introduced into the composition of aerated concrete. It is recommended to lay aerated concrete blocks on a special glue. When using cement, they absorb moisture from the solution, which significantly worsens thermal insulation.

gas silicate differs from aerated concrete of the main binder material: for aerated concrete it is lime (62% quartz sand and 24% lime), for aerated concrete it is cement (up to 60%). Moreover, gas silicate is produced exclusively in autoclaves. These materials differ in color and hygroscopicity: gas silicate is always white and actively absorbs moisture, as a result of which it can collapse, while aerated concrete simply lets moisture through, maintaining comfortable humidity in the room, and if you choose from these two materials, then it is better to use gas concrete.

The gas silicate block has a white color, so the main material is lime

You can find detailed information about the construction of gas silicate blocks in the video. foam concrete - one of the varieties of cellular concrete. It is made from a mixture of sand, cement and water, into which foam is mixed from a special foam generator. The manufacturing process is simple, allowing it to be made privately. This is where the danger lies: there is a high probability of acquiring low-quality material, which will quickly break down.

Bath from foam concrete blocks

The advantages of foam concrete include its lower cost (compared to aerated concrete) and better water resistance. Comparison of gas silicate and foam concrete blocks, see the video.

cinder blocks made from slag poured with concrete solution - waste obtained after the combustion of coal or other materials. This type of material is the cheapest, but there is one peculiarity: the slag must be aged for at least a year, otherwise it releases harmful substances.

Cinder blocks - the cheapest type of building material

Sawdust can be used as a filler in the manufacture of building blocks. In this case, the material is called sawdust concrete. This material is easily cut and drilled, 2 times higher than brick in terms of thermal conductivity. In addition, it is environmentally friendly and non-flammable (sawdust is insulated with a layer of concrete), has a small weight. The disadvantages can be a rather high absorbency, but it can be reduced by almost half due to the preliminary treatment of sawdust with water-repellent solutions or due to waterproofing of the walls.

Sawdust concrete is absolutely safe and environmentally friendly

Expanded clay concrete - a material that in most cases replaced the cinder block. In this case, expanded clay serves as a filler - foamed and fired clay. This material is absolutely non-toxic, almost does not absorb moisture, has excellent heat-insulating properties. Blocks of expanded clay concrete have a relatively small weight, which facilitates construction work. A bath made of expanded clay concrete is more practical than foam blocks or aerated concrete: less heat-insulating materials are required and it is easier to install fasteners.

Construction of a bath from expanded clay concrete

The heat-insulating properties of expanded clay concrete depend on the fraction of the filler - the larger the fraction, the better the thermal insulation, but the lower the density. When building a bath from expanded clay concrete, it is better to carry out insulation from the inside of the room (a layer of basalt wool is recommended, on top of which foil paper is laid with an air gap of 2.5 cm to finishing materials). The table shows some block parameters that will help you decide which one is preferable for you.

aerated concrete

sawdust concrete

foam concrete

Expanded clay concrete

cinder block

Strength kg/cm2

Thermal conductivity

Bulk weight kg/m3

Frost resistance (number of cycles)

Wall cooling time

Shrinkage (mm/m)

Water absorption

ceramic blocks

I would like to say a few words about the possibility of using ceramic blocks for the construction of a bath. Recently, you can see an advertisement for this building material, which claims that a ceramic block is much stronger and warmer than ordinary brick. As laboratory tests and inspections of objects built from ceramic blocks show, everything is not as good as manufacturers are trying to present.

From what we saw above, we can conclude that ceramic blocks should not be used in the construction of a bath.

Features of the construction of a bath from blocks

Any construction begins with the choice of the type of foundation. If you decide to build a bath from blocks, you should stop at a strip or pile foundation - most blocks are light in weight, and baths are usually a one-story structure and there is no need to spend extra time, money and effort on making a more complex foundation.

The laying of blocks is carried out by analogy with brickwork, with the only difference being that it is desirable to lay a metal mesh every 2-3 rows. It will give additional rigidity strength to the entire structure. In order to make the work easier, it is very important to lay out the first row of blocks evenly. They need to level and compensate for all existing irregularities in the foundation. At the very top, you can strengthen the crown of the timber, to which it will be convenient to attach the rafter system and the roof base.

For insulation, it is desirable to use a layer of basalt wool, on top of which a foil film or vapor barrier membranes are laid. It is desirable to provide a gap between the foil (membrane) and finishing materials by stuffing slats 2.5 cm thick and attaching the lining to them.

Thermal insulation and moisture protection of the bath with the help of foil films

Most blocks require exterior wall finishing. Here everyone chooses to their taste: you can plaster and paint, overlay with finishing stone or brick, etc. You can finish the walls with siding, but for better ventilation there should be a distance from the wall to the siding (for foam concrete at least 5 cm). The roof for a bath from blocks can be any - to your taste without any special restrictions.

According to historians, the banya appeared in Russia in the fifth century AD. The first baths were without a chimney, smoke and soot got inside the room. Such baths were called black. Later they began to make a chimney, a bath with a chimney was considered white. Stone baths appeared in the 17th century. Since ancient times, a visit to the bath has been healing and ritual, it was believed that in them a person is cleansed not only physically, but also spiritually. Today, the industry produces various blocks for the bath. Which is better, there is no clear answer. It is necessary to consider their qualities, advantages and disadvantages.

You can build a bath from wood. But today, wood and carpentry work are quite expensive. Therefore, the most popular materials for the construction of baths are blocks. Their use is convenient, they are lightweight, due to the small size of the bath, its construction does not require a complex foundation and concrete frame. Blocks differ in production technology and price. Consider different types of blocks.

Aerated concrete blocks

Made from cement and quartz sand. They have a cellular structure. Advantages of this type of blocks: light weight, ease of processing (can be cut with a regular hacksaw), good thermal insulation, incombustibility. The disadvantage is hygroscopicity. For laying walls, it is best to use the D500 block (density 0.5 t / m3). The price of one cube. meters 3200 rubles.

gas silicate blocks

Made from quartz sand and lime. Relate to cellular blocks. When saturated with moisture, they lose strength. Therefore, additional material for insulation is required. The price is 3000 rubles per cubic meter. meter.

Foam concrete blocks

They are made of cement and sand with the addition of foam. Advantage: High thermal insulation. The disadvantage is low strength. If you purchase these blocks, you must carefully check them for cracks. The price is 2800 rubles per cubic meter. meter.

cinder blocks

They are produced by mixing the products of combustion of any materials, most often coal, with cement. The advantage is the low price of only 1,750 rubles per cubic meter. meter. The disadvantage is that it can release harmful substances.

sawdust concrete blocks

In the manufacture of these blocks, sawdust is an additive to cement. Advantages: has good thermal insulation, environmentally friendly. The disadvantage is high hygroscopicity; before using this type of blocks, they must be treated with a waterproof composition. The price is 2400 rubles per cubic meter. meter.

Expanded clay blocks

In recent years, they have become widespread. It is made as a cinder block, expanded clay is used instead of slag. Advantages: easy to cut and drill, has good thermal insulation, non-flammable. The disadvantage is low strength, with careless handling, chipping is possible. The price is 2580 rubles per cubic meter. meter.

sand blocks

They are made from a cement-sand mixture by vibrocompression. Advantages: high strength, water resistance. The disadvantage is a large mass. The price is 2600 rubles per cubic meter. meter.

Heat blocks

They are a three-layer composition. The first layer is decorative, the second layer is insulating, it consists of expanded polystyrene, the third layer is the supporting layer, it is made of expanded clay concrete. Advantages: high thermal insulation, aesthetics. The disadvantage is the relatively high price of 4,500 rubles per cubic meter. meter.

Polystyrene concrete blocks

They are a monolithic structure, the composition of the material is cement, quartz sand, polystyrene, plasticizers. Advantages: high strength, thermal insulation, vapor permeability. Disadvantages: difficult to drill and cut, low adhesion to plaster materials. The price is 3100 rubles per cubic meter. meter.

Wood concrete blocks

Cement-based blocks with the addition of sand and sawdust. They have strength, environmental friendliness, the highest thermal insulation of all existing types. Disadvantages: combustibility, high hygroscopicity. With prolonged exposure to moisture, they lose strength. A huge plus is that you can hammer nails into the walls of wood concrete and screw in self-tapping screws without fear that they will fall out. The price is 2200 rubles per cubic meter. meter.

ceramic blocks

Made from baked clay. Unlike bricks, they have a porous cellular structure. Advantages: environmental safety, good thermal insulation, vapor permeability. Disadvantages: relative fragility, high price. One cube a meter of ceramic blocks costs 3800 rubles.

The composition of the material does not differ from white brick and includes lime and quartz sand. There are hollow and solid silicate blocks. Such blocks have high strength, a smooth surface, so you can do without plastering. The disadvantage is hygroscopicity. The price is 3500 rubles per cubic meter. meter.

Block selection

Now you can decide for yourself from which blocks it is better to build a bath. Blocks made of wood concrete, sawdust concrete, silicate and gas silicate blocks have increased hygroscopicity. Since the bath is a source of moisture, their use necessarily requires additional coatings, which increases costs.

When considering other types of blocks, you should determine which qualities are crucial to you, and which are secondary. If you need to make fasteners from the inside of the room, then you should not use polystyrene concrete blocks, because they are difficult to drill.

How to build a bath with your own hands from building blocks

So, you have already decided which blocks to build a bath from. Now you need to proceed directly to its construction. First of all, you need to choose a place for construction and draw up a project. Usually the project includes a steam room, a washing department, a dressing room and a rest room.

Foundation device

Construction starts with the foundation. For a small 4x4 bath, a foundation on piles is most suitable. A pile is a steel pipe equipped with blades and a tip at the bottom. The pile is screwed in with a crowbar inserted into the eye. The distance between the piles should be 2 - 2.5 meters. The length of the pile is 2.5 meters. The minimum distance from the ground surface to the pile tip is 1.5 meters. Cement mortar is poured into the cavity of the piles after their installation.

We weld a metal channel to the ground heads of the piles. We get the perimeter, called the strapping. This is the base for laying blocks, it must be horizontal, checked for level.

Building walls

Masonry begins with corner blocks, a thread is pulled between them. Adhering to the line given by the thread, lay out the first row. We check the first row with a level and proceed to the second row. This is how walls are built.

We cut the roof

• beam 100X100 mm,
• board 50X100 mm,
• vapor barrier film
• roofing material.

A frame is assembled from the boards, a vapor barrier film is attached from the inside. The roof is laid on top.

Finishing a bath from building blocks

The decoration of the premises, except for the steam room, is carried out with PVC panels. The steam room is trimmed with timber (lining) made of linden. First, a wooden crate is attached to the walls. Wooden and plastic panels are mounted to it.

After completion of the finishing work, a furnace is installed: metal or brick. The installation location of the stove must be determined in advance in order to make a hole for the chimney in the ceiling.

Thus, here are the main stages of building a bathhouse from the foundation to the roof. And for laying walls, use bath blocks, which are best for you.

Video about the bath of building blocks