How is the installation of cast iron sewer pipes? Chasing and chasing cast iron pipes How cast iron pipes are minted.

The main advantage of cast iron is durability, its main disadvantage is brittleness. These two features must be taken into account when maintaining and repairing cast iron pressure pipes.
The brittleness of cast iron imposes certain requirements on the connection of cast iron pipes. On the one hand, it must be strong and tight, and on the other hand, it must be sufficiently elastic. The fact is that pipes laid in the ground do not lie motionless. The soils are also characterized by shrinkage and blurring. When freezing, the water in the ground expands. All this leads to the movement of the ground. The pipe, as they say, "walks". Traditionally this problem is solved chasing pipes- connecting pipes in such a way that there is a margin of elasticity at the joints.
The smooth end of one pipe is inserted into the socket of the other. A small 3-5 mm gap remains at the junction, which is caulked two-thirds of the depth with a resin strand (cabole). The strand is a thin rope, which is inserted into the gap in layers. After each turn, the strand is compacted with a caulk - a special tool. Such a connection allows you to connect the pipe hermetically, but with a margin of elasticity.
To increase the strength of the joint, the remaining third of the gap is cemented or filled with lead. The second option is more reliable and preferable, because. connections in pressure pipes experience significant loads. Both procedures are quite complex and time-consuming. Cement behaves capriciously at high or low humidity, work with the melting of lead requires dexterity and additional preparations.
More advanced methods of connecting cast-iron pressure pipes are currently being used. For example, a socket with a rubber sealing ring and a socket-screw connection. But these compounds began to be used relatively recently. Recall that the advantage of cast iron is durability. The service life of cast iron pressure pipes is more than a hundred years. And, therefore, pipelines made according to old technologies are still actively exploited.
Chasing socket connection can be safely called the weakest point of the cast-iron pipeline. Under the influence of moisture, temperature changes and soil movement for decades, the coinage is destroyed. Typically, accidents caused destruction of coinage, are eliminated for a long time. Procedure minting time-consuming, requiring a certain skill. But even high qualification does not guarantee the absence of marriage. The liquidation of an accident is often carried out in difficult conditions: low temperatures, difficult access to the damaged area, watering of the pit, humidity that prevents the solution from hardening. Fussing with molten lead in such conditions is generally more like a repairman's nightmare. Alas, this dream often comes true. It is almost impossible to perform high-quality coinage during the liquidation of a complex accident.
Our company's product range includes a special type of fittings that can significantly reduce the time required to eliminate this type of accident and improve the quality of repair work on a cast-iron pipeline. This is a socket sealer DZ. With him, all work comes down to installing the product on the socket connection and fixing it with a conventional wrench. The rubber gasket securely seals the joint, without depriving it of the necessary elasticity, and the design itself firmly fixes the joint. Work can be carried out even without completely blocking the pressure, but only by reducing it so that the leak does not interfere with the repair team. The reliability of the connection of cast-iron pressure pipes with the help of a socket joint sealer is several times higher than the reliability of traditional caulking. And, therefore, once the work is done, the problem will be eliminated once and for all.

Almost all Soviet buildings are equipped with cast-iron sewer communications, since such pipes are durable and resistant to wear. But the cast iron pipeline requires the right approach to use and dismantling.

Unlike drain pipes, which can last for decades, connections inside a home may need to be replaced sooner. Also, interventions in the sewer system may be forced during the installation of washing equipment or redevelopment of the bathroom. To do it according to the rules, it is not necessary to call and wait for the master, all the work can be mastered by the owner himself, if he knows how to handle elementary tools. Dismantling the sewer should not take much time, but dismantling old products is more difficult. Let's figure out how to properly dismantle cast iron pipes.

Step-by-step caulking of cast-iron pipes

In the process of repairing sewer communications with your own hands, the most difficult moment may be caulking a cast-iron pipe. Such manipulation may be required when repairing or reinstalling the riser. In this case, it is necessary to very carefully emboss the pipes of the cast-iron pipes. Step by step, this work can be done like this:

First, use a hammer to lightly tap the socket, while being careful not to break it, since carelessness can lead to irreversible consequences, for example, replacing the entire riser. It is better to use a wooden mallet.
If the previous blockage was made with the help of a cable, then after tapping the socket should wobble freely and can be removed without additional effort. In such a case, do the following:
- swing the bell from side to side;
- pry with a screwdriver and pull the rope a little;
- hook it with pliers;
- slowly and carefully pull out the rope, swinging the pipe in the process.
If, after tapping, the pipe did not start moving, it means that the previous caulking of the sockets of sewer pipes was carried out by pouring sulfur. In this option, you will need to get rid of it by burning it. To do this, proceed as follows:
- gently heat the pipe at the joint along the entire diameter with a blowtorch or burner;
- lightly, trying not to break the walls of the pipe, then tap it with a hammer;
- if the bell starts to wobble, try moving it using an adjustable wrench.
Please note that when working with a burner and sulfur, it is imperative to protect the respiratory tract with a mask so as not to get poisoned by toxic fumes.
After successful dismantling, the walls of the socket must be well cleaned with a chisel and chisel. Pay special attention to the bell seat, as this is where you will place the sealing rubber.
Having previously coated the rubber seal with a special lubricant, place it in the socket.
Place a new structural element in the rubber ring.

Precautions in repairing cast iron pipes

When working with such pipes, be sure to remember that cast iron is a relatively brittle material with its endurance. If you hit the metal hammer hard or too hard, the wall will vibrate, which may cause cracks. If this happens, the replacement of damaged sections will be long and expensive. Therefore, when preparing for dismantling, stock up on the necessary tools in advance.

Don't work alone, it is unsafe and difficult. Better call someone for help.

It's important to know that sulfur fumes can be harmful to health, so use a gas mask, in extreme cases, a respirator and goggles. Also take care of good air circulation in the room where the repair work is taking place.

After removing the pipe from the socket, take the time and attention to clean the seat of this part. So you will ensure the installation of the sealing material without defects and distortions.

Immediately pack all dismantled material and garbage into construction bags, tie and throw away. An unpleasant smell will come from the old pipeline.

If you are caulking cast iron pipes for the first time and after reading this article, you still do not understand how to do it, be sure to contact a professional. For an experienced craftsman, the process of dismantling cast iron pipes will take 25-30 minutes, while a beginner can spend more than 3 hours and with an unknown result.

Since chasing cast iron pipes is a very laborious job, as any specialist will tell you, it is wiser to carry out preventive inspections than to wait until a large-scale repair of the sewer system is required. Since cast iron is still mainly used for external sewer networks as the main material for pipes, which cannot be completely replaced by modern plastic counterparts, prevention should be treated with all due attention. In our article, we will focus on two types of repair work - caulking and caulking of cast iron pipes.

Chasing cast iron pipes

Preparation for repair

Sometimes it becomes necessary to repair some part of the sewerage system. However, such repairs can not always be made without disconnecting the pipes. When it is required to replace a pipeline section, you should first inspect the place of future work to determine how the pipes were connected to each other at one time.

Often the main difficulty is that pipes, especially those located in the ground, are filled with a special compound that prevents them from separating. In this case, the question arises of how to emboss a cast-iron pipe without much effort and time.

It is possible to quickly disconnect the pipes by using a gas cutter to remove the composition, which fastens the elements of the system.

Pipe chasing technology

Do-it-yourself caulking of cast-iron pipes, carried out when replacing a riser or changing a toilet bowl, can create an equally problematic problem. In this case, it becomes necessary to caulk the branch pipe of the cast-iron pipe as accurately as possible. The embossing process looks like this:

The first action to be taken is to tap the socket of the pipe with a hammer, being careful not to split it, in order to avoid a complete replacement of the riser.
After making sure that the bell moves quite freely and can be released without any problems, since it was caulked with a heel, you can proceed with dismantling:
- slightly loosen the bell from side to side;
- pry with a screwdriver and pull the rope a little;
- firmly grab the rope with pliers;
- gently, slowly, pull out the rope, while continuing to loosen the tube.

In the case when the bell does not budge after tapping, that is, the caulking of cast-iron pipes was carried out by pouring sulfur, you will have to use the method of burning it out:
- carefully heat the pipe in a circle with a blowtorch or burner;
- trying not to damage the pipe, continue gently tapping the pipe with a hammer;
- when the bell starts to move, slightly loosen it from side to side with an adjustable wrench.

When performing an operation to burn sulfur, it is imperative to wear a respirator so as not to be poisoned by harmful fumes.

After the bell is safely released, it must be cleaned using a chisel or chisel. Particular care should be taken to clean the socket seat, where the sealing rubber will be placed.
Coat the rubber seal with special grease and insert into the socket.
Install a new part in the seal.

Chasing pipes

When assembling a system consisting of cast-iron pipes, it is necessary to foresee a method for closing the gaps that remain invariably between the outer side of the inserted part of the pipe and the inner surface of the socket. That is, you should think about how to mint cast-iron pipes. There are two ways to solve the problem, let's consider them in more detail.

Sealing of sockets with cement mixture

The chasing technology looks like this:

Resin seal installation.

caulk the resin tourniquet into the socket up to 2/3 of its depth;
when forming the first rope ring, wrap the end of the bundle over the ring so that it does not fall into the pipe.

The use of cement mortar.

mix cement marking 300-400 with water (by weight) in a ratio of 9:1;
the place remaining after compaction of the bundle in the socket should be filled with cement mortar;
firmly strike the cement with a chasing and a hammer until the chasing rebounds from the cement;
for a better setting of the solution after caulking, cover it with a wet rag.

To increase work productivity, it is worth using broadened caulking and embossing, which allows you to speed up the process by about 30%.

If work is carried out in winter, cement should be mixed with hot water, and the joints must be insulated after sealing.

Sealing of sockets with asbestos cement

Another way to caulk a cast-iron pipe is to use an asbestos-cement mixture. The process has two differences:

A dry mixture of asbestos fiber and cement is prepared by mixing them in a ratio of 1:2.
Before direct use, the dry mixture is moistened with water: from 10 to 12% of the initial mass of the mixture.

The chasing technology itself looks similar to the first method.

On this, a rather laborious work - chasing and / or chasing cast-iron pipes - is completed. To achieve the best result, however, such work should be entrusted to qualified specialists. Only in this case, you can be sure that everything will be done correctly, and you will not have to deal with more complex repairs, eliminating the flaws of poor-quality installation or dismantling.

Do-it-yourself installation of sewer pipes requires the contractor to fully comply with the rules of construction work and standards. In most cases, these issues have already been resolved for multi-apartment buildings, so this process is relevant for private houses and cottages. It is for this reason that owners need to know all the nuances of building a drainage system. In our article we will find out how to make a sewer with our own hands.

It is necessary to install water pipes from the drawing up of communication laying diagrams. The photo should indicate and indicate all the components of the structure: the dimensions of the elements, the location of the fittings, the lines of the system. In practice, most plumbing fixtures are connected to one riser, but if the room is large, it is better to connect to several points.

When the question arises of installing a sewer system, you can start from the photo of the previous wiring diagram in the building. It is worth considering that if a cast-iron pipe is replaced with a plastic one, then it is impossible to focus on the old system.

Attention! With a large number of storeys of the building, it is rational to place the plumbing units one under the other.

When performing repair work, it is enough to make a schematic drawing of the adjustable system. But, if sewage installation is being carried out, then it is impossible to do without drawing up a project. This norm is necessary due to the existence of an internal and external design of the drainage system. Plus, most cases also involve the installation of a cleaning device.

Work materials

For such types of work, the requirements of SNiP provide for the installation of the following types of pipes:

cast iron;
ceramic;
Asbestos-cement;
ceramic;
Plastic.

Most often, polyethylene materials are used, which correspond to GOST 22689.0-89 and 22689.2-89, and have a diameter of 40 to 110 mm. A feature of plastic pipes is resistance to aggressive environmental influences and corrosion. Such devices are connected using sockets, and rubber cuffs are used for sealing.

Basic rules of the installation process

Before proceeding with the installation work on the sewer, you should familiarize yourself with the basic requirements for the process. This is necessary to create an optimal drainage system in the house. For this reason, it is very important to do everything correctly and accurately.

Sizes of diameters and slopes of pipes

Since most situations involve the creation of a system with gravity, it becomes very important to choose the diameter and slope of the pipes correctly. The functioning of the sewer will depend on this process. The size of the pipe dimensions is affected by the type of plumbing fixtures, as well as their number in the building. Generally speaking, the main factor is the photo installation diagram. So here are some recommendations:

It is better to insert a pipe diameter into the washbasin system - 4 cm;
For bathroom and kitchen - 5 cm;
For a riser that does not have a connection to the toilet - 8.5 cm;
For a riser with a connected toilet - 10 cm

Attention! The pipe must be directed to the riser from the apparatus. It is worth noting that its dimensions should be 2-15 cm per meter.

Dismantling the old wiring

Before mounting a new system, you need to remove the elements of the old layout. It is worth noting that this process can be quite a difficult job, especially for old-timers' houses. In order to speed up and facilitate the procedure, it is necessary to think about dismantling in advance.

Required Tools

To install the sewer with your own hands, you will need the following tools:

Special grinder or hacksaw;
Drill apparatus;
Screwdriver.

It is right to start all work from the bathroom and the most distant places of pipelines. Before starting the process, it is necessary to check whether all the necessary materials and tools are available. In addition, we advise you to perform pipe diagnostics to determine if there are any deformations and damages on them.

Preparatory stages of installation

Preparation for installation includes the following steps:

We check and adjust all connection points. We mark on the pipes the depths of the occurrences of the sockets.
Next, the chasing and cutting of pipes is performed;

Attention! The caulking of the pipeline occurs at an angle of 90 degrees. It should be noted that the cut should not have deformations or distortions.

The points of cut pipes should be correctly checked for burrs, as their presence on the part will affect the sealing of the joints and lead to the accumulation of debris and blockages. You need to fix this situation with a file.
Before assembling the system, it is necessary to clean the extreme parts of the pipes and the rubber seals. Failure to comply with this norm will reduce the quality of the connection.

If you focus on the standard photo, the sewerage scheme in the premises, then it provides that the pipe wiring is carried out along three lines of the system:

The device of the first highway is the line with the shortest length, which should not exceed 1 meter. In this branch, it is necessary to mint a toilet bowl and other plumbing fixtures in the house.
The second line includes bathroom appliances and equipment, namely a washbasin, shower, washing machine.
The third branch is the drainage line from the kitchen.

Attention! The length of the second and third branches should be less than three meters. For this reason, if the building has a large volume, then it is necessary to insert the lines into at least two risers.

The main sewer lines have several branches that go to each type of plumbing. Each line at the end provides for the installation of a siphon. A water lock is a necessary element of any system that forms a cork from the water, which prevents gases from escaping from the sewer. In most cases, such an apparatus does not exist in the installation of a washing machine, since its system has a check valve.

Chasing cast iron pipes

Sometimes there are situations when there is a need to perform repairs for a separate part of the sewer system. It should be noted that the process does not always occur without disconnection of the pipeline. To start minting pipes, you need to inspect the place of future work.

The main problem is that the pipes that are in the ground are filled with a special substance, which strengthens the fastening. Therefore, the question arises, how is the chasing of cast-iron pipelines performed? This is what we are now trying to find out. It is enough to simply destroy the connection using a gas cutter.

Pipe chasing technology

Difficulty can also arise when chasing cast-iron or plastic pipes, which occurs when replacing a riser or toilet bowl. For the correctness of the action, you need to very carefully mint the pipe pipe. This action includes several steps:

The first thing we need to do is to tap the bell with a hammer so as not to damage it;
If the bell moves quietly and can be easily dismantled, which means that the caulking was carried out with a cable.
Then you can start dismantling - loosen the bell, pry with a screwdriver and pull the cord a little. Then gently pull out the rope with pliers.

If the bell is motionless when tapped, this means that the chasing was done with sulfur. In this situation, you need to use the burning technology:

Carefully perform heating of the pipeline around the circumference with a burner or blowtorch;
Avoiding damage, carefully tap the pipeline with a hammer;
When the bell is movable, you can loosen it with an adjustable tool.

Attention! When performing work, it is necessary to use a respirator to avoid inhalation of sulfur.

After releasing the bell, we clean it with a chisel;
We cover the sealing ring with a special solution, and insert it into the socket;
We mount a new part in the seal.

Installation of plastic sewer pipes

Installing plastic sewer pipes is a little different from other types. For this reason, we provide some tips on how to mint them:

There are two ways to cut a plastic pipe. It is worth noting that the saw for such work should have small teeth. Also, this task can be performed using a two-handed cable.
Do not leave burrs, which very often appear when cutting plastic products.
We carry out cleaning and gluing of materials. First, you need to perform a dry assembly, and then you can start gluing the system. To do this, we make marks, and then we connect the structural elements with glue.
We assemble the sewerage pipeline system.
We fill in all the empty spaces.
We install a plastic pipe for ventilation. The connection must be made with copper material.
Plastic pipes are used for connections of high complexity. The strength of the tightness of the structure is provided by couplings without a socket.
We strengthen the risers. To do this, use metal lining - this element will protect against accidental hits of small parts, such as nails or screws.

So, we found out that installing a sewer is quite simple. The article presents two options for completing the process - a design with cast iron and plastic pipes. The main requirement for installation is compliance with the rules and regulations that are regulated by SNiP and Gost RF. So, study the legislative base and construction and sanitary conditions, and then you will be able to install a drainage system in your own house or apartment correctly.

Add to bookmarks

Cast iron is a high strength material with a lot of weight. From it, objects are usually made that are required to withstand heavy loads, as well as elements for arranging the sewerage and water supply systems. Caulking pipes is not an easy job, and therefore, in order to avoid costly and complex repairs, it is recommended that facilities be regularly inspected for deformations.

In what cases is chasing performed?

This work is justified when it is necessary to replace a damaged cast-iron element of the system. It is also carried out in the case when the deformation cannot be corrected at the accident site. Damage to cast iron pipes is a fairly common problem, despite their increased strength. This material is very sensitive to water, chemical processes, temperature changes. As a result, the elements of the system cease to withstand the previous loads, and a decision has to be made on repair work.

If a crack has formed in the pipe, measures must be taken without delay, otherwise a small problem can lead to an emergency. Patching cracks with special solutions is only a temporary measure, so it is better to immediately pay attention to more reliable methods.

Training

Correct chasing

First of all, it is required to inspect the place of work, the pipes themselves. In this case, you need to see how they are connected to each other. The fact is that it is not always possible to do chasing with your own hands without disconnecting the pipes.

The problem arises if the cast-iron elements are located in the ground and during installation they were filled with a composition that promotes gluing. The difficulty lies in the fact that often the structural elements grow together with each other so firmly that they can be separated only with the help of additional tools. Usually, a gas cleaver is used in this capacity, which contributes to the effective removal of the bonding solution.

It may be necessary to turn off the water in the entire house during repairs. If repairs are made on an important site, this may entail turning off the water in the entire area. Preparation for caulking is carried out using the following tools:

Bulgarian. Required for cutting the deformed area;
New piping element. Installed to replace the damaged one;
Construction bandage and cement mortar. Needed to close the seam.

How is chasing done?

Repair work on repairing cast-iron pipes should be done very carefully. It is better to entrust this important matter to professionals, but if you still decide to do the chasing with your own hands, the following instructions will help you:

Now you know how to do-it-yourself cast-iron pipes. If something remains unclear to you, on our website you can always see a photo that shows the described repair work. A video has also been published, from which you will learn how professional caulking of cast-iron pipes is performed.

Cast iron is a heavy-duty, corrosion-resistant, durable material that can withstand heavy loads. Its main purpose is the device of sewer and water communication. But you should not completely pin your hopes on the cast-iron sewer, since it also has disadvantages, they need special care and repair. In this article, we will look at how to caulk cast-iron pipes with your own hands.

In order to exclude depressurization of individual sections of communications, it is necessary to repair the internal pipes in a timely manner and take preventive measures, removing lime deposits, rust and other organic growths from their surface.

Chasing

The essence of the preparatory work is to inspect and determine the welded places. There are two methods for gluing cast iron pipe parts: gluing the elements with a welding seam and pouring with a mortar. Bonding of parts with a special solution is used if it is necessary to combine pipes of various configurations and diameters. And with a welding seam, fan pipes of the same diameter are mainly glued together. After a visual inspection of the sewer and determining the complexity of the work, you can proceed to the next stage - dismantling.

Most often, over the years, pipes grow together so strongly that it is very difficult to disassemble the sewer. In this case, you need a gas cutter, with which you can disconnect the spliced sections in a short period of time and without effort.

Before proceeding with the caulking of pipes, it is necessary to turn off the water supply. If possible, it is necessary to shut off the water supply system.

The designated section of the pipe, which is to be replaced, is sawn off by a grinder. When sawing damaged areas, strong blows should not be made in order to prevent the formation of cracks in subsequent sections.
After the removal of damaged sections of the pipe is completed, they proceed to install a new pipe with a certain margin for its expansion.

The edges of the pipe, which are inserted into the pipe, are fixed together with a resin strand using a caulk.

Pipe branch

This process is very complex and differs markedly from the previous method. This is argued by the fact that this area is risky and if the caulking is carried out incorrectly, then the riser can be split along the drop line.

Before you start disassembling the pipe, you need to take a hammer and tap on the entire surface of the socket. When tapping, you can determine the method of embossing.

If the bell easily gives in and staggers, then it was minted with a rope and a camboca. In this case, you will need an ordinary screwdriver and pliers. When loosening, a rope should appear, which must be hooked with a screwdriver and taken out to the surface. To make it easier to pull out the rope, it must be grabbed with pliers at the same time, without ceasing to loosen the socket.

Caulking a cast-iron pipe with sulfur eliminates deformation and loosening, therefore, not a hammer or other percussion instrument will help with this. In this case, you will need a blowtorch or a gas burner to burn the sulfur seam. From a high temperature, sulfur will begin to dry out and fall off. After the sulfur has crumbled, take a hammer and follow the same procedure as described in the previous method of caulking a pipe with a rope.

Perform tapping until the bell starts to move, so that it is convenient to loosen the bell, take an adjustable wrench and begin to carry out oscillatory movements from side to side, pulling it towards you. The loosened socket is taken out with a chisel and cleaned.

The saddle should be flat without distortions so that the sealing gum lies tightly to the surface.

The surface of the gum is coated with silicone and inserted into the tee of the bell. At this stage, the caulking and caulking of the cast-iron pipe is completed.

Video

We bring to your attention a video dedicated to chasing pipes.

This article will discuss the caulking of cast-iron pipes - what this procedure is, how to prepare for it and prevent the need to perform it, as well as an example of caulking using the example of a cast-iron pipe.

Cast iron is a material with very high strength as well as high weight. The density of the structure allows the manufacture of massive and strong products from it that can withstand significant loads, due to which cast iron pipes are used as elements of water supply and sewerage systems.

Even with the development of chemical production and the active use of pipes from various plastic options, when laying an external water supply, cast iron is most often used as a more serious material. are usually used in the construction of sewerage systems with very heavy loads, significantly exceeding household ones.

Buildings of catering establishments, factories processing meat and other animal products, etc. they constantly create a stream of waste, quite often leading to ruptures of cast iron pipes, which should be immediately repaired.

And taking into account the fact that the caulking and caulking of cast iron pipes is quite difficult, experts recommend conducting annual scheduled inspections to avoid time-consuming repairs.

Start and sequence of repairs

It is necessary to think about how to emboss a cast-iron pipe if it is necessary to replace the element and it is impossible to correct the damage directly at the site of the accident.

First of all, they carry out preparatory work, that is, they carefully inspect the pipes and figure out exactly how they are welded to each other.

Quite often you have to deal with pipes filled with a special solution used to glue their parts.

In this case, while underground, the elements can grow together so firmly that they cannot be detached without effort. At the same time, experts recommend using a gas cutter, which allows you to quickly remove the fastening compound and separate the pipes.

Speaking of chasing a cast-iron pipe, it should be borne in mind that the work ahead is not easy and requires turning off the water in the whole house or even the area if an important area is being repaired.

Pipe preparation for repair is carried out using special tools:

Cut off the damaged or burst area with a grinder;
Install a new part of the pipe in place of the damage;
The seam is closed with a construction bandage with cement.

Preventing the Problem from Occurring

It should be borne in mind that with all the excellent physical qualities, cast iron is a rather fragile material. It deforms under the action of water and the chemical reactions that occur in it, so all changes affect the pipes, including temperature changes, which makes them fragile and unable to withstand high pressure.

Chasing cast-iron pipes is a rather complex process, the high-quality implementation of which includes leaving a certain margin for its expansion.

The new part of the pipe is inserted into the socket, after which the seam must be securely fixed with a resin strand. To tightly lay and secure the threads, a tool such as caulking is used.

Practical experience shows that the formation of cracks is only part of the problem, which grows if drastic measures are not taken. Patching holes with the help of special compounds temporarily helps, but sooner or later a replacement will still be required, so it’s easier to deal with the breakdown right away.

Chasing a cast iron pipe

When replacing a sewer riser, a lounger from a common riser, a toilet bowl, etc. many faced the problem of caulking a cast-iron pipe. It turned out that the procedure is not as simple as it seems.

Let us consider in more detail the process of caulking a cast-iron pipe:

At the same time, they begin to loosen the socket in different directions;
Pry off the rope with a screwdriver;
Grab the rope with pliers;
Slowly pull the rope, loosening the bell.

If the socket sits firmly, this indicates that it is most likely filled with sulfur and knocking on it is useless. In this case, using a burner or a blowtorch, they start in a circle. In this case, you should also be careful not to damage the socket.